hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
595
| content
stringlengths 0
6.67M
|
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1 and table 8.2.2.1.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.1.1: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.2.2.1.2: Cell re-selection single carrier to intra-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
9
7
9
7
7
9
7
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-66
-66
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2 1,28 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1A and 8.2.2.1.2A.
Table 8.2.2.1.1A: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑– Persistence value
0..1
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.2.2.1.2A: Cell re-selection to intra-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
7
10
7
7
10
7
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-66
-66
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/ 1.28 MHz
-70
Propagation Condition
AWGN
Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for SYNCH-UL sequence in the UpPTS for sending for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps b)-g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3 7,68 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3.1 Initial conditions | This scenario implies the presence of 1 carrier and 6 cells as given in table 8.2.2.1.1B and table 8.2.2.1.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.1.1B: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1.28
The value shall be used for all cells in the test.
DRX cycle length
s
1.28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.2.2.1.2B: Cell re-selection to intra-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
9
7
9
7
7
9
7
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-66
-66
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2,C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3,C6:0
Qhyst 1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.1 3,84 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.2 1,28 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.1.5.3 7,68 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2 Scenario 2: Cell re-selection to inter-frequency TDD cell | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on cell 2.
This test is applicable to 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell, and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.1 3,84 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to table 4.1 in clause 4.2.2.7 in [2].
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.2 1,28 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
TevaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate NTDD of 6.4s according to table 4.1A in clause 4.2 in [2].
TSI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.2.3 7,68 Mcps Option | The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to table 4.1B in clause 4.2.2.7.3 in [2].
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.3 Test purpose | This test is to verify the requirement for the cell re-selection delay in the multi carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1 and table 8.2.2.2.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1: General test parameters for Cell Re-selection to inter-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.2.2.2.2: Cell re-selection to inter-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
dB
10
7
10
7
7
10
7
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-66
-66
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel
Channel 2
Channel
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times.
NOTE: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1A and table 8.2.2.2.2A. For this test purpose the broadcast repetition period of the target cell shall be 1.28s. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1A: General test parameters for Cell Re-selection to inter-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.2.2.2.2A: Cell re-selection to inter-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
4
10
4
4
10
4
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-69
-69
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/1,28 MHz
-70
Propagation Condition
AWGN
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps b)-g) until the confidence level according to annex F.6.2 is achieved.
NOTE: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3 7,68 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3.1 Initial conditions | This scenario implies the presence of 2 carriers and 6 cells as given in table 8.2.2.2.1B and table 8.2.2.2.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2.1B: General test parameters for Cell Re-selection to intra-frequency TDD cell
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1.28
The value shall be used for all cells in the test.
DRX cycle length
s
1.28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.2.2.2.2B: Cell re-selection to intra-frequency TDD cell
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
6
0
6
0
0
6
0
6
-3
-3
-3
-3
PCCPCH RSCP
dBm
-67
-73
-73
-67
-76
-76
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
PCCPCH RSCP
dBm
-76
-76
-76
-76
-76
-76
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) until the confidence level according to annex F.6.2 is achieved.
NOTE: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.1 3,84 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.2 1,28 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.2.5.3 7,68 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.2.2.2A Scenario 2A: 3,84 Mcps TDD cell re-selection for 1,28 Mcps TDD UE
[FFS]
8.2.2.2B Scenario 2B: 1,28 Mcps TDD cell re-selection for 3,84 Mcps TDD UE
FFS
8.2.2.2C Scenario 2C: 3,84 Mcps TDD cell re-selection for 7,68 Mcps TDD UE
8.2.2.2C.1 Definition and applicability
The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test applies to to UEs supporting both 3.84 Mcps TDD and 7.68Mcps TDD.
8.2.2.2C.2 Minimum requirement
The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE:
TevaluateTDD + TSI
where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to Table 4.1B in section 4.2.
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.2.
8.2.2.2C.3 Test purpose
This test is to verify the requirement for the cell re-selection delay in the 7.68Mcps TDD to 3.84 Mcps TDD case.
8.2.2.2C.4 Method of test
8.2.2.2C.4.1 Initial conditions
This scenario implies the presence of 1 higher chip rate (7.68 Mcps TDD OPTION) and 1 high chip rate (3.84 Mcps TDD OPTION)) cell as given in Table 8.2.2.2C.1 and 8.2.2.2C.1.
Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2C.1: General test parameters for TDD higher chip rate (7.68 Mcps) to TDD high chip rate (3.84 Mcps) cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
7.68 Mcps TDD OPTION cell
Neighbour cell
Cell2
3.84 Mcps TDD OPTION cell
Final condition
Active cell
Cell2
3.84 Mcps TDD OPTION cell
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
S
1,28
The value shall be used for all cells in the test.
DRX cycle length
S
1,28
The value shall be used for all cells in the test.
T1
S
30
T2
S
15
Table 8.2.2.2C.2: Test parameters for TDD higher chip rate (7.68 Mcps) to TDD high chip rate (3.84 Mcps) cell re-selection
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
8
0
8
T1
T2
T 1
T 2
T1
T2
T 1
T 2
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
PICH_Ec/Ior
dB
-3
-3
-3
-3
OCNS_Ec/Ior
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
10
7
10
7
7
10
7
10
PCCPCH_RSCP
dBm
-63
-66
-66
-63
Qoffset1s,n
dB
C1, C2: 0
C2, C1: 0
Qhyst1s
dB
0
0
Treselection
s
0
0
Sintersearch
dB
not sent
not sent
-70 dBm/7.68 MHz
-70 dBm/3.84 MHz
Propagation Condition
AWGN
8.2.2.2C.4.2 Procedure
a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times.
NOTE: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these.
8.2.2.2C.5 Test Requirements
1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.2.2.2D Scenario 2D: 7,68 Mcps TDD cell re-selection for 3,84 Mcps TDD UE
8.2.2.2D.1 Definition and applicability
The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
The requirements and this test applies to to UEs supporting both 3.84 Mcps TDD and 7.68Mcps TDD.
8.2.2.2D.2 Minimum requirement
The cell re-selection delay shall be less than 8 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE:
TevaluateTDD + TSI
where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to Table 4.1B in section 4.2.
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.2.
8.2.2.2D.3 Test purpose
This test is to verify the requirement for the cell re-selection delay in the 3.84Mcps TDD to 7.68 Mcps TDD case.
8.2.2.2D.4 Method of test
8.2.2.2D.4.1 Initial conditions
This scenario implies the presence of one 3.84 Mcps TDD serving cell, and one 7.68 Mcps TDD cell to be re-selected. The UE is requested to monitor neighbouring cells on one 3.84Mcps TDD carrier and one 7.68 Mcps TDD carrier. Test parameters are given in Table 8.2.2.2D.1and 8.2.2.2D.2.
Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.2D.1: General test parameters for 3.84 Mcps /7.68 Mcps TDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell 1
3.84 Mcps TDD OPTION cell
Neighbour cell
Cell 2
7.68 Mcps TDD OPTION cell
Final condition
Active cell
Cell 2
7.68 Mcps TDD OPTION cell
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
S
1,28
The value shall be used for all cells in the test.
DRX cycle length
S
1,28
The value shall be used for all cells in the test.
T1
S
30
T2
S
15
Table 8.2.2.2D.2: Cell 1 specific test parameters for 3.84 Mcps TDD/7.68 Mcps TDD cell re-selection
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
8
0
8
T1
T2
T 1
T 2
T1
T2
T 1
T 2
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
PICH_Ec/Ior
dB
-3
-3
-3
-3
OCNS_Ec/Ior
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
10
7
10
7
7
10
7
10
PCCPCH_RSCP
dBm
-63
-66
-66
-63
Qoffset1s,n
dB
C1, C2: 0
C2, C1: 0
Qhyst1s
dB
0
0
Treselection
s
0
0
Sintersearch
dB
not sent
not sent
-70 dBm/3.84 MHz
-70 dBm/7.68 MHz
Propagation Condition
AWGN
8.2.2.2D.4.2 Procedure
a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times.
NOTE: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these.
8.2.2.2D.5 Test Requirements
1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 8 s.
3) In step g), the UE shall respond on cell 2 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3 Scenario 3: TDD/FDD Cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
This test is for the case where the UE camps on a 3,84 Mcps TDD cell and reselects to an FDD cell.
The requirements and this test apply to UEs supporting both 3,84 Mcps TDD and FDD. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on cell 2.
This test is for the case where the UE camps on a 1,28 Mcps TDD cell and reselects to an FDD cell.
The requirements and this test apply to UEs supporting both 1,28 Mcps TDD and FDD. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on the new cell.
This test is for the case where the UE camps on a 7,68 Mcps TDD cell and reselects to an FDD cell.
The requirements and this test apply to UEs supporting both 7,68 Mcps TDD and FDD. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.1 3,84 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD See TS 25.123 [2] table 4.1 in clause 4.2.2.
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.2 1,28 Mcps TDD Option | The minimum requirement for the cell re-selection delay is less than 8 s with a DRX cycle length of 1280ms.
This shall be verified in more than 90% of the cases with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2]clauses 4.2.2 and A4.2.3.
NOTE: The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a TevaluateFDD of 6.4s according to table F2.4.1.A in Annex F clause F.2.4.
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7,68 s, allow 8 s in the test case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.2.3 7,68 Mcps TDD Option | The cell re-selection delay shall be less than 8 s when the DRX cycle length is 1,28 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE:
The cell re-selection delay can be expressed as: TevaluateFDD + TSI, where:
TevaluateFDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s. See TS 25.123 [2] table 4.1 in clause 4.2.2.
TSI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.3 Test purpose | The test purpose is to verify the requirement for the cell re-selection. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1.1 Initial conditions | This scenario implies the presence of 1 TDD and 1 FDD cell as given in table 8.2.2.3.4.1 and table 8.2.2.3.4.2. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.3.4.1: General test parameters for the TDD/FDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
TDD cell
Neighbour cells
Cell2
FDD cell
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.2.2.3.4.2: TDD/FDD cell re-selection
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
8
n.a
n.a.
T1
T2
T 1
T 2
T 1
T 2
UTRA RF Channel Number
Channel 1
Channel 2
CPICH_Ec/Ior
dB
n.a.
n.a.
-10
-10
PCCPCH_Ec/Ior
dB
-3
-3
-12
-12
SCH_Ec/Ior
dB
-9
-9
-9
-9
-12
-12
SCH_toffset
0
0
0
0
n.a.
n.a.
PICH_Ec/Ior
dB
-3
-3
-15
-15
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-0,941
-0,941
dB
3
-2
3
-2
-2
3
dBm/3,84 MHz
-70
CPICH_RSCP
dBm
n.a.
n.a.
-82
-77
PCCPCH_RSCP
dBm
-70
-75
n.a.
n.a.
Cell_selection and reselectionquality _measure
CPICH_RSCP
CPICH_RSCP
Qrxlevmin
dBm
-102
-115
Qoffset1s,n
dB
C1, C2: -12
C2, C1: +12
Qhyst1s
dB
0
0
Treselection
s
0
0
Sintersearch
dB
not sent
not sent
Propagation Condition
AWGN
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.1.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2.1 Initial Conditions | This test is to verify the requirement for the 1,28 Mcps TDD OPTION/FDD cell re-selection delay reported in clause 4.2. in [2]
This scenario implies the presence 1.28Mps TDD serving cell, and 1 FDD cell to be selected. The UE is requested to monitor neighbouring cells on 1 1.28Mcps TDD carrier and 1 FDD carrier. Test parameters are given in table 8.2.2.3.4.1A and table 8.2.2.3.4.2A.
Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.3.4.1A: General test parameters for the TDD/FDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
1,28 Mcps TDD OPTION cell
Neighbour cells
Cell2
FDD cell
Final condition
Active cell
Cell2
FDD cell
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.2.2.3.4.2A: Test parameters for the 1,28 Mcps TDD OPTION/FDD cell re-selection
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
DwPts
n.a.
T1
T2
T 1
T 2
T1
T2
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-12
-12
DwPCH_Ec/Ior
dB
0
0
n.a.
CPICH_Ec/Ior
dB
n.a.
n.a.
-10
-10
SCH_Ec/Ior
dB
n.a.
n.a.
-12
-12
PICH_Ec/Ior
dB
-15
-15
OCNS_Ec/Ior
dB
-3
-3
-0,941
-0,941
dB
8
2
8
2
-3
-3
-70 dBm/1.28MHz
-70 dBm/3.84MHz
PCCPCH_RSCP
dBm
-65
-71
n.a.
n.a.
CPICH_RSCP
n.a.
-83
-77
Cell_selection_and_reselection quality _measure
CPICH_RSCP
CPICH_RSCP
Qrxlevmin
dBm
-103
-115
Qoffset1s,n
dB
C1, C2: -12
C2, C1: +12
Qhyst1s
dB
0
0
Treselection
s
0
0
Sintersearch
dB
not sent
Propagation Condition
AWGN
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.2.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps b)-g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3 7,68 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3.1 Initial conditions | This scenario implies the presence of 1 TDD and 1 FDD cell as given in table 8.2.2.3.4.1B and table 8.2.2.3.4.2B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.3.4.1B: General test parameters for the TDD/FDD cell re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
TDD cell
Neighbour cells
Cell2
FDD cell
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
DRX cycle length
s
1.28
The value shall be used for all cells in the test.
T1
s
30
During T1 cell 1 better ranked than cell 2
T2
s
15
During T2 cell 2 better ranked than cell 1
Table 8.2.2.3.4.2B: TDD/FDD cell re-selection
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
8
n.a
n.a.
T1
T2
T 1
T 2
T 1
T 2
UTRA RF Channel Number
Channel 1
Channel 2
CPICH_Ec/Ior
dB
n.a.
n.a.
-10
-10
PCCPCH_Ec/Ior
dB
-3
-3
-12
-12
SCH_Ec/Ior
dB
-9
-9
-9
-9
-12
-12
SCH_toffset
0
0
0
0
n.a.
n.a.
PICH_Ec/Ior
dB
-3
-3
-15
-15
OCNS_EcIor
dB
-3,12
-3,12
-3,12
-3,12
-0,941
-0,941
dB
3
-2
3
-2
-2
3
-70 dBm/7.68 MHz
-70 dBm/3.84 MHz
CPICH_RSCP
dBm
n.a.
n.a.
-82
-77
PCCPCH_RSCP
dBm
-70
-75
n.a.
n.a.
Cell_selection_and reselection_quality _measure
CPICH_RSCP
CPICH_RSCP
Qrxlevmin
dBm
-102
-115
Qoffset1s,n
dB
C1, C2: -12
C2, C1: +12
Qhyst1s
dB
0
0
Treselection
s
0
0
Propagation Condition
AWGN
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.4.3.2 Procedure | a) The SS activates cell 1 and cell 2 with T1 defined parameters and monitors them for RRC CONNECTION REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 30 s, the parameters are changed as described for T2.
e) The SS waits for RRC CONNECTION REQUEST messages from the UE.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.1 3,84 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.2 1,28 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.3.5.3 7,68 Mcps TDD Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 8 s.
3) In step g), the UE shall respond on cell 1 within 8 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4 Scenario 4: inter RAT cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.1 3,84 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 3,84 Mcps TDD cell and reselects to a GSM cell.
The requirements and this test apply to UEs supporting both 3,84 Mcps TDD and GSM. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send LOCATION UPDATING REQUEST message to perform a Location update.
This test is for the case where the UE camps on a 1,28 Mcps TDD cell and reselects to a GSM cell.
The requirements and this test apply to UEs supporting both 1,28 Mcps TDD and GSM. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.1.3 7,68 Mcps Option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 7,68 Mcps TDD cell and reselects to a GSM cell.
The requirements and this test apply to UEs supporting both 7,68 Mcps TDD and GSM. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.1 3,84 Mcps Option | The cell re-selection delay shall be less than 26 s + TBCCH, where TBCCH is the maximum time allowed to read BCCH data in the GSM cell.
NOTE: The cell re-selection delay can be expressed as:
4 * TmeasureGSM + TBCCH
where:
TmeasureGSM Specified in Table 4.1 in sub clause 4.2.2.7.1 in [2].
TBCCH Equal to 1.9 s, i.e. the maximum time allowed to read BCCH data when synchronised to a BCCH carrier from a GSM cell (specified in TS 45.005).
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.4 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.2 1,28 Mcps Option | The cell re-selection delay shall be less than 8 s + TBCCH where TBCCH is the maximum time allowed to read BCCH data from GSM cell.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: Max(3*TmeasureNTDD , Tmeasure GSM +1DRX)+ TBCCH, where:
TmeasureTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a TmeasureNTDD of 1.28s according to Table 4.1A in [2].
TmeasureGSM A DRX cycle length of 1280ms is assumed for this test case, this leads to a TmeasureGSM of 6.4s according to Table 4.1A in [2].
DRX cycle length 1.28s is assumed, see Table A.4.1A in [2].
TBCCH Maximum time allowed to read BCCH data from GSM cell in TS 45.005.
According to[20], the maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.
This gives a total of 7.68s +TBCCH, thus allow 8s +TBCCH.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.4 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.2.3 7,68 Mcps Option | The cell re-selection delay shall be less than 26 s + TBCCH, where TBCCH is the maximum time allowed to read BCCH data in the GSM cell [21].
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
4 * TmeasureGSM + TBCCH
where:
TmeasureGSM Specified in Table 4.1B in sub clause 4.2.2.7.3 in [2].
TBCCH Equal to 1.9 s, i.e. the maximum time allowed to read BCCH data when synchronised to a BCCH carrier from a GSM cell [21].
This gives a total of 25.6 s + TBCCH, allow 26 s + TBCCH in the test case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.3 Test purpose | This test verifies the UE meets the minimum requirement for the case where the UE camps on a TDD cell and reselects to a GSM cell. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4 Method of Test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.1 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.1.1 Initial conditions | This scenario implies the presence of 1 3,84 Mcps TDD and 1 GSM cell as given in table 8.2.2.4.1, 8.2.2.4.2, and 8.2.2.4.3. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.4.1: General test parameters for UTRAN to GSM Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
TDD Cell
Neighbour cell
Cell2
GSM Cell
Final condition
Active cell
Cell2
DRX cycle length
s
1,28
UTRAN cell
BCCH repetition period (GSM cell)
s
1,87
In GSM the system information is scheduled according to an 8 x (51 x 8) cycle (i.e. a system information message is transmitted every 235 ms). The cell selection parameters in system info 3 and 4 are transmitted at least every second. (GSM 05.02)
T1
s
45
T2
s
35
Table 8.2.2.4.2: Cell re-selection UTRAN to GSM cell case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
8
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
SCH_toffset
0
0
0
0
PICH_Ec/Ior
dB
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
dB
3
-2
3
-2
dBm/3,84 MHz
–70
–70
PCCPCH RSCP
dBm
-70
-75
Propagation Condition
AWGN
AWGN
Treselection
s
0
SsearchRAT
dB
not sent
Table 8.2.2.4.3: Cell re-selection UTRAN to GSM cell case (cell 2)
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-90
-75
RXLEV_ACCESS_MIN
dBm
-100
MS_TXPWR_MAX_CCH
dBm
30 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.1.2 Procedure | a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST and LOCATION UPDATING REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 45 s, the parameters are changed as described for T2.
e) The SS waits for LOCATION UPDATING REQUEST messages from the UE.
f) After 35 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) [TBD] times. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.2.1 Initial conditions | This scenario implies the presence of 1 1,28 Mcps TDD serving cell, and 1 GSM cell to be re-selected. Test parameters are given in table 8.2.2.4.1A, 8.2.2.4.2A, and 8.2.2.4.3A.
The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304. Cell 1 and cell 2 shall belong to different location areas.
Table 8.2.2.4.1A: General test parameters for UTRAN (1,28 Mcps TDD OPTION) to
GSM Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cell
Cell2
Final condition
Active cell
Cell2
DRX cycle length
s
1,28
T1
s
15
T2
s
15
Table 8.2.2.4.2A: Cell re-selection UTRAN to GSM cell case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
dB
13
-12
13
-12
dBm/1,28 MHz
-80
PCCPCH RSCP
dBm
-70
-95
n.a.
n.a.
Propagation Condition
AWGN
AWGN
Treselection
s
0
SsearchRAT
dB
Not sent
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Table 8.2.2.4.3A: Cell re-selection UTRAN to GSM cell case (cell 2)
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-75
-75
RXLEV_ACCESS_MIN
dBm
-104
MS_TXPWR_MAX_CCH
dBm
33 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.2.2 Procedure | a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST and LOCATION UPDATING REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for LOCATION UPDATING REQUEST messages from the UE.
f) After 15 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps b)-g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.3 7,68 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.3.1 Initial conditions | This scenario implies the presence of 1 7,68 Mcps TDD and 1 GSM cell as given in table 8.2.2.4.1B, 8.2.2.4.2B, and 8.2.2.4.3B. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.4.1B: General test parameters for UTRAN to GSM Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
UTRA TDD Cell
Neighbour cell
Cell2
GSM Cell
Final condition
Active cell
Cell2
HCS
Not used
DRX cycle length
s
1,28
UTRA TDD cell
T1
s
45
T2
s
35
Table 8.2.2.4.2B: Cell re-selection UTRAN to GSM cell case (cell 1)
Parameter
Unit
Cell 1 (UTRA TDD)
Timeslot Number
0
8
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
SCH_toffset
0
0
0
0
PICH_Ec/Ior
dB
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
dB
3
-2
3
-2
dBm/7,68 MHz
-70
-70
PCCPCH RSCP
dBm
-70
-75
n.a.
n.a.
Propagation Condition
AWGN
AWGN
Qrxlevmin
dBm
-102
Qoffset1s, n
dB
C1, C2: 0
Qhyst1
dB
0
Treselection
s
0
SsearchRAT
dB
not sent
Table 8.2.2.4.3B: Cell re-selection UTRAN to GSM cell case (cell 2)
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-90
-75
RXLEV_ACCESS_MIN
dBm
-104
MS_TXPWR_MAX_CCH
dBm
33 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.4.3.2 Procedure | a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST and LOCATION UPDATING REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 45 s, the parameters are changed as described for T2.
e) The SS waits for LOCATION UPDATING REQUEST messages from the UE.
f) After 35 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps d) to g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.5.1 3,84 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 27.9 s.
3) In step g), the UE shall respond on cell 1.
For the test to pass, the total number of fulfilled test requirements in step 2) shall be at least 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.5.2 1,28 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 9.7 s.
3) In step g), the UE shall respond on cell 1.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.4.5.3 7,68 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 27.9 s.
3) In step g), the UE shall respond on cell 1.
For the test to pass, the total number of fulfilled test requirements in step 2) shall be at least 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5 Scenario 4A: inter RAT cell acquisition and re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.1.1 3,84 Mcps Option | Void
Note: Scenario 4A does not apply for 3,84 Mcps TDD, this section numbering is purely for consistency with TS 25.123, where corresponding sections are also void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.1.2 1,28 Mcps Option | The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send RR Channel Request message for location update to Cell 2. ,
Unlike 1,28 Mcps scenario 4 the initial GSM RX_LEV is set below monitoring threshold and GSM measurements do not start until the second phase of the test. The requirements and this test apply to UEs supporting both 1,28 Mcps TDD and GSM. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.1.3 7,68 Mcps Option | Void
Note: Scenario 4A does not apply for 7,68 Mcps TDD, this section numbering is purely for consistency with TS 25.123, where corresponding sections are also void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.2.1 3,84 Mcps Option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.2.2 1,28 Mcps Option | The cell re-selection delay shall be less than 26 s+ TBCCH, where TBCCH is the maximum time allowed to read BCCH data from GSM cell [21].
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The UE shall keep a running average of 4 measurements, thus gives 4* TmeasureGSM +TBCCH, where:
TmeasureGSM A DRX cycle length of 1280ms is assumed for this test case, this leads to a TmeasureGSM of 6.4s according to Table 4.1A in section 4.2. in [2].
TBCCH Maximum time allowed to read BCCH data from GSM cell in TS 45.005 [20].
According to [21], the maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.
This gives a total of 25,6s +TBCCH, thus allow 26s +TBCCH.
The normative reference for this requirement is TS 25.123 [2] clauses 4.2.2 and A.4.2.4.3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.2.3 7,68 Mcps Option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.3 Test purpose | This test verifies the UE meets the minimum requirement for the case where the UE camps on a TDD cell and then acquires and reselects to a GSM cell |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4 Method of Test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4.1 3,84 Mcps Option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4.2 1,28 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4.2.1 Initial conditions | This scenario implies the presence of 1 1,28 Mcps TDD serving cell, and 1 GSM cell to be re-selected. Test parameters are given in table 8.2.2.5.1A, 8.2.2.5.2A, and 8.2.2.5.3A.
The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304. Cell 1 and cell 2 shall belong to different location areas.
Table 8.2.2.5.1A: General test parameters for UTRAN (1,28 Mcps TDD OPTION) to GSM Cell Re-selection Scenario 4A
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
1,28 Mcps TDD OPTION cell
Neighbour cell
Cell2
GSM cell
Final condition
Active cell
Cell2
GSM cell
DRX cycle length
s
1,28
HCS
Not Used
T1
s
45
T2
s
45
Table 8.2.2.5.2A: Cell re-selection UTRAN to GSM cell case (cell 1) Scenario 4A
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
OCNS_Ec/Ior
dB
-3
-3
dB
6
6
6
6
dBm/1,28 MHz
-80
PCCPCH RSCP
dBm
-77
-77
Propagation Condition
AWGN
AWGN
Treselection
s
0
SsearchRAT
dB
Not sent
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Table 8.2.2.5.3A: Cell re-selection UTRAN to GSM cell case (cell 2) Scenario 4A
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-90
-70
RXLEV_ACCESS_MIN
dBm
-104
MS_TXPWR_MAX_CCH
dBm
33 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4.2.2 Procedure | a) The SS activates cell 1 and 2 with T1 defined parameters and monitors cell 1 and 2 for RRC CONNECTION REQUEST and LOCATION UPDATING REQUEST messages from the UE.
b) The UE is switched on.
c) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
d) After 45 s, the parameters are changed as described for T2.
e) The SS waits for RR Channel Request message for a location update to Cell 2 from the UE.
f) After 45 s, the parameters are changed as described for T1.
g) The SS waits for RRC CONNECTION REQUEST messages from the UE.
h) Repeat steps b)-g) until the confidence level according to annex F.6.2 is achieved. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.