hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
595
| content
stringlengths 0
6.67M
|
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.5.4.2 Procedure | 1) The wanted signal frequency channel is set to mid range frequency. The wanted signal power level shall be set according to Table 6.5.5.1a for the 3,84 Mcps TDD option, Table 6.5.5.2a for the 1,28 Mcps TDD option and Table 6.5.5.3a for the 7,68 Mcps TDD option.
2) The interfering Signal Generator is set to the frequency offset values indicated in table 6.5.2.1a for the 3,84 Mcps TDD Option, table 6.5.2.2a for the 1,28 Mcps TDD Option and table 6.5.2.3a for the 7,68 Mcps TDD Option. The interfering signal level shall be set according to Table 6.5.5.1a for the 3,84 Mcps TDD option, Table 6.5.5.2a for the 1,28 Mcps TDD option and Table 6.5.5.3a for the 7,68 Mcps TDD option.
3) The interference signal shall be equivalent to a continuously running wideband CDMA signal with one code and chip frequency 3,84 Mchip/s for the 3,84 Mcps TDD Option, 1,28 Mchp/s for the 1,28 Mcps TDD Option and 7,68 Mchip/s for the 7,68 Mcps TDD Option, respectively and rolloff 0.22.
4) Measure the BER of the wanted signal received from the UE at the SS for each step of the interferer.
5) The wanted signal frequency channel is set to an arbitrary frequency chosen from the low, mid or high range. The level of the wanted signal shall be set according to Table 6.5.5.1b for the 3,84 Mcps TDD option, table 6.5.5.2b for the 1,28 Mcps TDD option and table 6.5.5.3b for the 7,68 Mcps TDD option.
6) The interfering Signal Generator is stepped through the frequency range indicated in table 6.5.2.1b for the 3,84 Mcps TDD Option, table 6.5.2.2b for the 1,28 Mcps TDD Option and table 6.5.2.3b for the 7,68 Mcps TDD Option, respectively with a step size of 1 MHz. The interfering signal level shall be set according to Table 6.5.5.1b for the 3,84 Mcps TDD option, Table 6.5.5.2b for the 1,28 Mcps TDD option and Table 6.5.5.3b for the 7,68 Mcps TDD option.
7) The interference signal is a CW signal.
8) Measure the BER of the wanted signal received from the UE at the SS for each step of the interferer.
9) Record the frequencies for which BER exceed the test requirements in Table 6.5.5.1b for the 3,84 Mcps TDD option, table 6.5.5.2b for the 1,28 Mcps TDD option and table 6.5.5.3b for the 7,68 Mcps TDD option. These frequencies are further proceeding in subclause 6.6 Spurious Response.
10) For 7,68Mcps TDD option repeat steps 1 to 9 except use the channel power levels defined for the addition test conditions specified in 6.5.5.3c and the frequency ranges specified in 6.5.2.3c.
NOTE: Due to the large amount of time-consuming BER tests it is recommended to speed up a single BER test by reducing the 0.001-BER confidence level [10 000 bits under test or 10 errors] for screening the critical frequencies. Critical frequencies must be identified using standard BER confidence level. [30 000 bits or 30 errors]. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.5.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.5.5.1 3,84 Mcps TDD Option | The measured BER, derived in step 4) shall not exceed 0,001 (without exception) under test conditions described in table 6.5.5.1a.
The measured BER, derived in step 8), shall not exceed 0,001 except for up to 24 different frequencies of the interfering signal under test conditions described in table 6.5.5.1b.
These frequencies are further processed in clause 6.6 Spurious response.
Table 6.5.5.1a: Test conditions In-band blocking (3,84 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-102
dBm/3,84 MHz
mean power (modulated)
-56
(for Fuw offset 10 MHz)
-44
(for Fuw offset 15 MHz)
dBm
Table 6.5.5.1b: Test conditions Out of band blocking (3,84 Mcps TDD Option)
Parameter
Band 1
Band 2
Band 3
Unit
0
0
0
dB
Îor
-102
-102
-102
dBm/3,84 MHz
Iouw (CW)
-44
-30
-15
dBm
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.5.5.2 1,28 Mcps TDD Option | The measured BER, derived in step 4), shall not exceed 0,001 (without exception) under test conditions described in table 6.5.5.2a.
The measured BER, derived in step 8), shall not exceed 0,001 except for up to 24 different frequencies of the interfering signal under test conditions described in table 6.5.5.2b.
These frequencies are further processed in clause 6.6 Spurious response.
Table 6.5.5.2a: Test conditions In-band blocking (1,28 Mcps TDD Option)
Parameter
Level
Unit
0
dB
-105
dBm/1,28 MHz
mean power (modulated)
-61
(for Fuw offset ±3.2 MHz)
-49
(for Fuw offset ±4.8 MHz)
dBm
Table 6.5.5.2b: Test conditions Out of band blocking (1,28 Mcps TDD Option)
Parameter
Band 1
Band 2
Band 3
Unit
0
0
0
dB
Îor
-105
-105
-105
dBm/1,28 MHz
Iouw
-44
-30
-15
dBm
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.5.5.3 7,68 Mcps TDD Option | The measured BER, derived in step 4) shall not exceed 0,001 (without exception) under test conditions described in table 6.5.5.3a.
The measured BER, derived in step 8), shall not exceed 0,001 except for up to 24 different frequencies of the interfering signal under test conditions described in table 6.5.5.3b and 6.5.5.3c.
These frequencies are further processed in clause 6.6 Spurious response.
Table 6.5.5.3a: Test conditions In-band blocking (7,68 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-102
dBm/7,68 MHz
mean power (modulated)
-53
(for Fuw offset 20 MHz)
-41
(for Fuw offset 30 MHz)
dBm
Table 6.5.5.3b: Test conditions Out of band blocking (7,68 Mcps TDD Option)
Parameter
Band 1
Band 2
Band 3
Unit
0
0
0
dB
Îor
-102
-102
-102
dBm/7,68 MHz
Iouw (CW)
-44
-30
-15
dBm
Table 6.5.5.3c: Test conditions additional Out of band blocking (7,68 Mcps TDD Option)
Parameter
Band 1
Band 2
Band 3
Unit
0
0
0
dB
-102
-102
-102
dBm/7.68 MHz
Iouw (CW)
-44
-30
-15
dBm
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4.
6.5A Blocking Characteristics (IMB)
6.5A.1 Definition and applicability
The blocking characteristics is a measure of the receiver ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels without this unwanted input signal causing a degradation of the performance of the receiver beyond a specified limit.. The blocking performance shall apply at all frequencies except those at which a spurious response occur.
The requirements of this test apply to 3.84 Mcps TDD IMB UE.
6.5A.2 Minimum Requirements
The BLER shall not exceed 0.01 for the parameters specified in table 6.5A.2.1a and table 6.5A.2.1b. For table 6.5A.2.1b up to 24 exceptions are allowed for spurious response frequencies in each assigned frequency channel when measured using a 1MHz step size for the interference signal.
The normative reference for this requirement is TS 25.102 clause 7.6.1.1.
Table 6.5A.2.1a: In-band blocking (3,84 Mcps TDD IMB)
Parameter
Level
Unit
-0.77
dB
Îor
-102
dBm/3,84 MHz
mean power (modulated)
-56
(for Fuw offset 10 MHz)
-44
(for Fuw offset 15 MHz)
dBm
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
Table 6.5A.2.1b: Out of band blocking (3,84 Mcps TDD IMB)
Parameter
Band 1
Band 2
Band 3
Unit
-0.77
-0.77
-0.77
dB
Îor
-102
-102
-102
dBm/3,84 MHz
Iouw
-44
-30
-15
dBm
Fuw
For operation in frequency bands as defined in clause 4.2(a)
1840 <f <1885
1935 <f <1995
2040 <f <2085
1815 <f <1840
2085 <f <2110
1< f <1815
2110< f <12750
MHz
Fuw
For operation in frequency bands as defined in clause 4.2(b)
1790 < f < 1835
2005 < f < 2050
1765 < f < 1790
2050 < f < 2075
1 < f < 1765
2075 < f < 12750
MHz
Fuw
For operation in frequency bands as defined in clause 4.2(c)
1850 < f < 1895
1945 < f < 1990
1825 < f < 1850
1990 < f < 2015
1 < f < 1825
2015 < f < 12750
MHz
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
NOTE 1: For operation referenced in 4.2(a), from 1885 <f< 1900 MHz, 1920 <f< 1935 MHz, 1995 <f< 2010 MHz and 2025<f< 2040 MHz , the appropriate in-band blocking or adjacent channel selectivity in clause 6.4.2.1 shall be applied.
NOTE 2: For operation referenced in 4.2(b), from 1835 < f < 1850 MHz and 1990< f < 2005 MHz, the appropriate in-band blocking or adjacent channel selectivity in clause 6.4.2.1 shall be applied.
NOTE 3: For operation referenced in 4.2(c), from 1895 < f < 1910 MHz and 1930< f < 1945 MHz, the appropriate in-band blocking or adjacent channel selectivity in clause 6.4.2.1 shall be applied.
6.5A.3 Test purpose
"The test stresses the ability of the UE receiver to withstand high-level interference from unwanted signals at frequency offsets of 10 MHz or more, without undue degradation of its sensitivity."
6.5A.4 Method of test
6.5A.4.1 Initial conditions
For in-band case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
For out-of-band case:
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequency to be tested: 1 arbitrary frequency chosen from the low, mid or high range; see clause G.2.4.
1) Connect the SS and the interfering Signal generator to the UE antenna connector as shown in figure A.5.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback mode 3 and start the loopback test. See TS 34.108 and TS 34.109 for details regarding loopback test mode 3 for MBMS.
6.5A.4.2 Procedure
1) The wanted signal frequency channel is set to mid range frequency. The wanted signal power level shall be set according to Table 6.5A.5.1a.
2) The interfering Signal Generator is stepped through the frequency range indicated in table 6.5A.2.1a with a step size of 1 MHz. The interfering signal level shall be set according to Table 6.5A.5.1a.
3) The interference signal shall be equivalent to a continuously running wideband CDMA signal with one code and chip frequency 3,84 Mchip/s and rolloff 0.22.
4) SS shall start the test by sending data on the MTCH radio bearer and maintain the count of transmitted RLC SDU blocks on the MTCH.
5) SS shall send a “UE TEST LOOP MODE 3 RLC SDU COUNTER REQUEST” message and wait for the UE to response with a “UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE” reporting the received RLC SDU counter value.
6) SS shall compute the RLC SDU error rate based on the transmitted RLC SDUs count and received RLC SDU count reported by the UE.
7) The test shall be run for the wanted signal received from the UE at the SS for each step of the interferer.
8) The wanted signal frequency channel is set to an arbitrary frequency chosen from the low, mid or high range. The level of the wanted signal shall be set according to Table 6.5A.5.1b.
9) The interfering Signal Generator is stepped through the frequency range indicated in table 6.5A.2.1b with a step size of 1 MHz. The interfering signal level shall be set according to Table 6.5A.5.1b
10) The interference signal is a CW signal.
11) SS shall start the test by sending data on the MTCH radio bearer and maintain the count of transmitted RLC SDU blocks on the MTCH.
12) SS shall send a “UE TEST LOOP MODE 3 RLC SDU COUNTER REQUEST” message and wait for the UE to response with a “UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE” reporting the received RLC SDU counter value.
13) SS shall compute the RLC SDU error rate based on the transmitted RLC SDUs count and received RLC SDU count reported by the UE.
14) The test shall be run for the wanted signal received from the UE at the SS for each step of the interferer.
15) Record the frequencies for which BLER exceed the test requirements in Table 6.5A.5.1b. These frequencies are further proceeding in subclause 6.6A Spurious Response.
NOTE: Due to the large amount of time consumed by the BLER test it is recommended to speed up a single BLER test by reducing the 0.01-BLER confidence level [1 000 blocks under test or 10 errors] for screening the critical frequencies. Critical frequencies must be identified using standard BLER confidence level. [3 000 blocks or 30 errors].
6.5A.5 Test requirements
The computed BLER, in step 6) shall not exceed 0.01 (without exception) under test conditions described in table 6.5A.5.1a.
The computed BLER, in step 13), shall not exceed 0.01 except for up to 24 different frequencies of the interfering signal under test conditions described in table 6.5A.5.1b.
These frequencies are further processed in clause 6.6A Spurious response.
Table 6.5A.5.1a: Test conditions In-band blocking (3,84 Mcps TDD IMB)
Parameter
Level
Unit
-0.77
dB
Îor
-102
dBm/3,84 MHz
mean power (modulated)
-56
(for Fuw offset 10 MHz)
-44
(for Fuw offset 15 MHz)
dBm
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
Table 6.5A.5.1b: Test conditions Out of band blocking (3,84 Mcps TDD IMB)
Parameter
Band 1
Band 2
Band 3
Unit
-0.77
-0.77
-0.77
dB
Îor
-102
-102
-102
dBm/3,84 MHz
Iouw (CW)
-44
-30
-15
dBm
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6 Spurious Response | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.1 Definition and applicability | Spurious response is a measure of the receiver's ability to receive a wanted signal on its assigned channel frequency without exceeding a given degradation due to the presence of an unwanted CW interfering signal at any other frequency at which a response is obtained i.e. for which the blocking limit is not met.
The requirements of this test apply to all types of UTRA for the UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.2 Minimum Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.2.1 3,84 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.6.2.1.
The normative reference for this requirement is TS 25.102 clause 7.7.1.1.
Table 6.6.2.1: Spurious Response (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-102
dBm/3,84 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.2.2 1,28 Mcps TDD Option | The BER shall not exceed 0.001 for the parameters specified in table 6.6.2.2.
Table 6.6.2.2: Spurious Response (1,28Mcps TDD Option)
Parameter
Level
Unit
0
dB
-105
dBm/1,28 MHz
(CW)
-44
dBm
Fuw
Spurious response frequencies
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.2.3 7,68 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.6.2.3.
The normative reference for this requirement is TS 25.102 clause 7.7.1.3.
Table 6.6.2.3: Spurious Response (7,68 Mcps TDD Option)
Parameter
Level
Unit
0
dB
-102
dBm/7.68 MHz
(CW)
-44
dBm
Fuw
Spurious response frequencies
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.3 Test purpose | Spurious response frequencies, identified in the blocking test, are measured against a less stringent test requirement. The test stresses the ability of the receiver to withstand high level interference signals without undue degradation of its sensitivity due to the receiver's frequency conversion concept. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequency to be tested: the same frequency as chosen in subclause 6.5.4.1 for Blocking characteristics out-of-band case.
1) Connect the SS and the unwanted signal to the UE antenna connector as shown in figure A.6.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback test mode and start the loopback test. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.4.2 Procedure | 1) Set the wanted signal frequency to the frequency used for the out-of-band blocking test. Set the power level of the wanted signal according to table 6.6.2.1 for the 3,84 Mcps TDD Option, table 6.6.2.2 for the 1,28 Mcps TDD Option and table 6.6.2.3 for the 7,68 Mcps TDD Option, respectively.
2) Set the frequency of the interferer signal according the recorded spurious response frequency values obtained from the out-of-band blocking test as described in 6.5.4.2, at which the blocking test failed. Set the power level of the interferer according to table 6.6.5.1 for the 3,84 Mcps TDD Option, table 6.6.5.2 for the 1,28 Mcps TDD Option and table 6.6.5.3 for the 7,68 Mcps TDD Option, respectively.
3) Measure the BER of DCH received from the UE at the SS. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.5.1 3,84 Mcps TDD | The measured BER, derived in step 3), shall not exceed 0,001 under. test conditions described in table 6.6.5.1 for the 3,84 Mcps TDD Option.
Table 6.6.5.1: Test Parameters Spurious Response (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-102
dBm/3,84 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.5.2 1,28 Mcps TDD | The measured BER, derived in step 3), shall not exceed 0,001 under test conditions described in table 6.6.5.2 for the 1,28 Mcps TDD Option.
Table 6.6.5.2: Test Parameters Spurious Response (1,28 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-105
dBm/1,28 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.6.5.3 7,68 Mcps TDD | The measured BER, derived in step 3), shall not exceed 0,001 under. test conditions described in table 6.6.5.3 for the 7,68 Mcps TDD Option.
Table 6.6.5.3: Test Parameters Spurious Response (7,68 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-102
dBm/3,84 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4.
6.6A Spurious Response (IMB)
6.6A.1 Definition and applicability
Spurious response is a measure of the receiver's ability to receive a wanted signal on its assigned channel frequency without exceeding a given degradation due to the presence of an unwanted CW interfering signal at any other frequency at which a response is obtained i.e. for which the blocking limit is not met.
The requirements of this test apply to 3.84 Mcps TDD IMB UE.
6.6A.2 Minimum Requirements
The BLER shall not exceed 0.01 for the parameters specified in table 6.6A.2.1.
The normative reference for this requirement is TS 25.102 clause 7.7.1.1.
Table 6.6A.2.1: Spurious Response (3,84 Mcps TDD IMB)
Parameter
Value
Unit
-0.77
dB
Îor
-102
dBm/3,84 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
6.6A.3 Test purpose
Spurious response frequencies, identified in the blocking test, are measured against a less stringent test requirement. The test stresses the ability of the receiver to withstand high level interference signals without undue degradation of its sensitivity due to the receiver's frequency conversion concept.
6.6A.4 Method of test
6.6A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequency to be tested: the same frequency as chosen in subclause 6.5A.4.1 for Blocking characteristics out-of-band case.
1) Connect the SS and the unwanted signal to the UE antenna connector as shown in figure A.6.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback mode 3 and start the loopback test. See TS 34.108 and TS 34.109 for details regarding loopback test mode 3 for MBMS.
6.6A.4.2 Procedure
1) Set the wanted signal frequency to the frequency used for the out-of-band blocking test. Set the power level of the wanted signal according to table 6.6A.2.1.
2) Set the frequency of the interferer signal according the recorded spurious response frequency values obtained from the out-of-band blocking test as described in 6.5A.4.2, at which the blocking test failed. Set the power level of the interferer according to table 6.6A.5.1.
3) SS shall start the test by sending data on the MTCH radio bearer and maintain the count of transmitted RLC SDU blocks on the MTCH.
2) SS shall send a “UE TEST LOOP MODE 3 RLC SDU COUNTER REQUEST” message and wait for the UE to response with a “UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE” reporting the received RLC SDU counter value.
3) SS shall compute the RLC SDU error rate based on the transmitted RLC SDUs count and received RLC SDU count reported by the UE.
6.6A.5 Test requirements
The computed BLER in step 3), shall not exceed 0.01 under test conditions described in table 6.6A.5.1.
Table 6.6A.5.1: Test Parameters Spurious Response (3,84 Mcps TDD IMB)
Parameter
Value
Unit
-0.77
dB
Îor
-102
dBm/3,84 MHz
Iouw (CW)
-44
dBm
Fuw
Spurious response frequencies
MHz
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7 Intermodulation Characteristics | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.1 Definition and applicability | Third and higher order mixing of the two interfering RF signals can produce an interfering signal in the band of the desired channel. Intermodulation response rejection is a measure of the capability of the receiver to receiver a wanted signal on its assigned channel frequency in the presence of two or more interfering signals which have a specific frequency relationship to the wanted signal.
The requirements of this test shall apply to all UTRA UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2 Minimum Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.1 3,84 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.7.2.1.
The normative reference for this requirement is TS 25.102 clause 7.8.1.1.
Table 6.7.2.1: Receive intermodulation characteristics (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
Îor
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
10
MHz
Fuw2 (Modulated)
20
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.2 1,28 Mcps TDD Option | The BER shall not exceed 0.001 for the parameters specified in table 6.7.2.2.
The normative reference for this requirement is TS 25.102 clause 7.8.1.2.
Table 6.7.2.2: Receive intermodulation characteristics (1,28 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-105
dBm/1,28 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
3.2
MHz
Fuw2 (Modulated)
6.4
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.2.3 7,68 Mcps TDD Option | The BER shall not exceed 0,001 for the parameters specified in table 6.7.2.3.
The normative reference for this requirement is TS 25.102 clause 7.8.1.3.
Table 6.7.2.3: Receive intermodulation characteristics (7,68 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-102
dBm/7.68 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
±20
MHz
Fuw2 (modulated)
±40
MHz |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.3 Test purpose | The test stresses the ability of the receiver to withstand two or more high level interference signals without undue degradation of its sensitivity due to the receiver's non-linear elements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and the unwanted signals to the UE antenna connector as shown in figure A.7.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback test mode and start the loopback test. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.4.2 Procedure | 1) Set the wanted and interfering signals as indicated in table 6.7.2.1 for the 3,84 Mcps TDD Option, table 6.7.2.2 for the 1,28 Mcps TDD Option and table 6.7.2.3 for the 7,68 Mcps TDD Option with positive offset with respect to the wanted signal.
2) Measure the BER of DCH received from the UE at the SS.
3) Set the interfering signals as indicated in table 6.7.2.1 for the 3,84 Mcps TDD Option, table 6.7.2.2 for the 1,28 Mcps TDD Option and table 6.7.2.3 for the 7,68 Mcps TDD Option with negative offset with respect to the wanted signal and repeat 2). |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.1 3,84 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.1 for the 3,84 Mcps TDD Option.
Table 6.7.5.1: Test parameters Receive intermodulation characteristics (3,84 Mcps TDD Option)
Parameter
Value
Unit
0
dB
ÎorWanted Signal Level
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
±10
MHz
Fuw2 (Modulated)
±20
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.2 1,28 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.2 for the 1,28 Mcps TDD Option.
Table 6.7.5.2: Test parameters Receive intermodulation characteristics (1,28 Mcps TDD Option)
Parameter
Level
Unit
0
dB
Îor
-105
dBm/1,28 MHz
Iouw1 (CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
±3.2
MHz
Fuw2 (Modulated)
±6.4
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in Annex F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in Annex F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.7.5.3 7,68 Mcps TDD Option | The measured BER, derived in step 2) and 3), shall not exceed 0,001 under test conditions described in table 6.7.5.3 for the 7,68 Mcps TDD Option.
Table 6.7.5.3: Test parameters Receive intermodulation characteristics (7,68 Mcps TDD Option)
Parameter
Value
Unit
0
dB
ÎorWanted Signal Level
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
±20
MHz
Fuw2 (Modulated)
±40
MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4.
6.7A Intermodulation Characteristics (IMB)
6.7A.1 Definition and applicability
Third and higher order mixing of the two interfering RF signals can produce an interfering signal in the band of the desired channel. Intermodulation response rejection is a measure of the capability of the receiver to receiver a wanted signal on its assigned channel frequency in the presence of two or more interfering signals which have a specific frequency relationship to the wanted signal.
The requirements of this test shall apply to 3.84 Mcps TDD IMB UE.
6.7A.2 Minimum Requirements
The BLER shall not exceed 0.01 for the parameters specified in table 6.7A.2.1.
The normative reference for this requirement is TS 25.102 clause 7.8.1.1.
Table 6.7A.2.1: Receive intermodulation characteristics (3,84 Mcps TDD IMB)
Parameter
Value
Unit
-0.77
dB
Îor
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
10
MHz
Fuw2 (Modulated)
20
MHz
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
6.7A.3 Test purpose
The test stresses the ability of the receiver to withstand two or more high level interference signals without undue degradation of its sensitivity due to the receiver's non-linear elements.
6.7A.4 Method of test
6.7A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS and the unwanted signals to the UE antenna connector as shown in figure A.7.
2) A call is set up according to the Generic call setup procedure.
3) Enter the UE into loopback mode 3 and start the loopback test. See TS 34.108 and TS 34.109 for details regarding loopback test mode 3 for MBMS.
6.7A.4.2 Procedure
1) Set the wanted and interfering signals as indicated in table 6.7A.2.1 with positive offset with respect to the wanted signal.
2) SS shall start the test by sending data on the MTCH radio bearer and maintain the count of transmitted RLC SDU blocks on the MTCH.
3) SS shall send a “UE TEST LOOP MODE 3 RLC SDU COUNTER REQUEST” message and wait for the UE to response with a “UE TEST LOOP MODE 3 RLC SDU COUNTER RESPONSE” reporting the received RLC SDU counter value.
4) SS shall compute the RLC SDU error rate based on the transmitted RLC SDUs count and received RLC SDU count reported by the UE.
5) Set the interfering signals as indicated in table 6.7A.2.1 with negative offset with respect to the wanted signal and repeat steps 2 to 4).
6.7A.5 Test requirements
The computed BLER in step 4) and 5), shall not exceed 0.01 under test conditions described in table 6.7A.5.1.
Table 6.7A.5.1: Test parameters Receive intermodulation characteristics (3,84 Mcps TDD IMB)
Parameter
Value
Unit
-0.77
dB
ÎorWanted Signal Level
-102
dBm/3,84 MHz
Iouw1(CW)
-46
dBm
Iouw2 mean power (modulated)
-46
dBm
Fuw1 (CW)
±10
MHz
Fuw2 (Modulated)
±20
MHz
NOTE: The term DPCH_Ec refers to the sum of the energy of the physical channels comprising the IMB DL reference measurement channel.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8 Spurious Emissions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.1 Definition and applicability | The Spurious Emissions Power is the power of emissions generated or amplified in a receiver that appear at the UE antenna connector.
The requirements of this test are applicable for all UTRA UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2 Minimum Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.1 3,84 Mcps TDD Option | The power of any spurious emission shall not exceed:
Table 6.8.2.1: Receiver spurious emission requirements (3,84 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz – 1 GHz
-57 dBm
100 kHz
1 GHz – 1,9 GHz and
1,92 GHz – 2,01 GHz and
2,025 GHz – 2,11 GHz
-47 dBm
1 MHz
1,9 GHz – 1,92 GHz and
2,01 GHz – 2,025 GHz and
2,11 GHz – 2,170 GHz
-60 dBm
3,84 MHz
2,170 GHz – 12,75 GHz
-47 dBm
1 MHz
The normative reference for this requirement is TS 25.102 [1] clause 7.9.1.1. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.2 1,28 Mcps TDD Option | The power of any spurious emission shall not exceed the maximum level specified in Table 6.8.2.2 and Table 6.8.2.2A.
Table 6.8.2.2: Receiver spurious emission requirements (1,28Mcps TDD Option)
Frequency Band
Measurement
Bandwidth
Maximum level
Note
30MHz f < 1GHz
100 kHz
-57 dBm
1GHz f 12.75 GHz
1 MHz
-47 dBm
Table 6.8.2.2A: Additional receiver spurious emission requirements (1.28 Mcps TDD Option)
Band
Frequency Band
Measurement Bandwidth
Maximum level
Note
a
703 MHz f < 803 MHz
1 MHz
-50 dBm
2010 MHz f MHz
1.28MHz
-64dBm
2570 MHz f MHz
1.28MHz
-64dBm
2300 MHz f MHz
1.28MHz
-64dBm
1880 MHz f z
1.28MHz
-64dBm
2110 MHz f MHz
3.84MHz
-60dBm
2620 MHz f MHz
3.84MHz
-60dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
b
1850 MHz f 910 MHz
1.28MHz
-64dBm
1910 MHz f 990 MHz
1.28MHz
-64dBm
c
1910 MHz f 1930MHz
1.28MHz
-64dBm
d
2570 MHz f z
1.28MHz
-64dBm
2010 MHz f z
1.28MHz
-64dBm
2110 MHz f z
3.84MHz
-60dBm
2620 MHz f z
3.84MHz
-60dBm
e
703 MHz f < 803 MHz
1 MHz
-50 dBm
2300 MHz f z
1.28MHz
-64dBm
2010 MHz f z
1.28MHz
-64dBm
1880 MHz f z
1.28MHz
-64dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
f
703 MHz f < 803 MHz
1 MHz
-50 dBm
1880 MHz f z
1.28MHz
-64dBm
2010 MHz f MHz
1.28MHz
-64dBm
2300 MHz f MHz
1.28MHz
-64dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
Note 1: The frequency bandwidth protection 703-803 MHz and 2496-2690 MHz test requirements for Bands a, e and f deviate from the requirements in TS 25.102 [1] Rel-10 and earlier releases.
The normative reference for this requirement is TS 25.102 [1] clause 7.9.1.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.2.3 7,68 Mcps TDD Option | The power of any spurious emission shall not exceed:
Table 6.8.2.3: Receiver spurious emission requirements (7,68 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz - 1 GHz
-57 dBm
100 kHz
1 GHz - 1.9 GHz and
1.92 GHz - 2.01 GHz and
2.025 GHz - 2.11 GHz
2.17 GHz - 2.57 GHz
-47 dBm
1 MHz
1.9 GHz - 1.92 GHz and
2.01 GHz - 2.025 GHz and
2.11 GHz - 2.170 GHz
2.57 Ghz - 2.69 GHz
-57 dBm
7.68 MHz
2.69 GHz - 12.75 GHz
-47 dBm
1 MHz
The normative reference for this requirement is TS 25.102 [1] clause 7.9.1.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.3 Test purpose | The test purpose is to verify the UE's ability to limit interference caused by receiver spurious emissions to the own and the other systems. The test requirements are tighter than in clause 5.5.3 ((TX) Spurious Emissions) because the time of Receive–Only-Operation is generally much longer than RX-TX-Operation. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: 1 arbitrary frequency selected between low, mid and high range; see clause G.2.4.
1) Connect the measurement equipment to the UE antenna connector according to figure A.8.
2) RF parameters are setup according to table 6.8.4.1a for 3,84 Mcps TDD option, 6.8.4.1b for 1,28 Mcps TDD and table 6.8.4.1a for 7,68 Mcps TDD option respectively.
3) A call is set up according to the setup procedure specified in TS34.108 [3] sub-clause 7.3.3, with the following exceptions for information elements in System Information Block type3.
Information Element
Value/Remark
- Cell selection and re-selection info
- CHOICE mode
TDD
- Sintrasearch
0 dB
- Sintersearch
0 dB
- RAT List
This parameter is configurable
- Ssearch,RAT
0 dB
- Maximum allowed UL TX power
Power level where Pcompensation=0
NOTE: The setup procedure (3) sets the UE into CELL_FACH state. With this state and the SS level (2) it is ensured that UE continuously monitors the S-CCPCH and no cell reselections are performed [see 25.304, subcl. 5.2.3.and 5.2.6]. No transmission of the UE will interfere with the measurement.
Table 6.8.4.1a: RF parameters for receiver spurious test (3,84Mcps TDD Option and 7.68Mcps TDD option)
Parameter
Unit
Level
PCCPCH_Ec/Ior
dB
-3
SCH_Ec/Ior
dB
-9
dB
9
PCCPCH RSCP
dBm
-64
Table 6.8.4.1b: RF parameters for receiver spurious test (1,28Mcps TDD Option)
Parameter
Unit
Level
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
dB
9
PCCPCH RSCP
dBm
-64 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.4.2 Procedure | Measure the average power of spurious emissions by covering the frequency ranges of table 6.8.2.1 for the 3,84 Mcps TDD Option, table 6.8.2.2 for the 1,28 Mcps TDD Option and table 6.8.2.3 for the 7,68 Mcps TDD Option. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.1 3,84 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.1 for the 3,84 Mcps TDD Option.
Table 6.8.5.1: Receiver spurious emission test requirements (3,84 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz – 1 GHz
-57 dBm
100 kHz
1 GHz – 1,9 GHz and
1,92 GHz – 2,01 GHz and
2,025 GHz – 2,11 GHz
-47 dBm
1 MHz
1,9 GHz – 1,92 GHz and
2,01 GHz – 2,025 GHz and
2,11 GHz – 2,170 GHz
-60 dBm
3,84 MHz
2,170 GHz – 12,75 GHz
-47 dBm
1MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.2 1,28 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.2 and table 6.8.5.2A for the 1,28 Mcps TDD Option.
Table 6.8.5.2: Receiver spurious emission requirements (1,28Mcps TDD Option)
Frequency Band
Measurement
Bandwidth
Maximum level
Note
30MHz f < 1GHz
100 kHz
-57 dBm
1GHz f 12.75 GHz
1 MHz
-47 dBm
Table 6.8.5.2A: Additional receiver spurious emission requirements (1.28 Mcps TDD Option)
Band
Frequency Band
Measurement Bandwidth
Maximum level
Note
a
703 MHz f < 803 MHz
1 MHz
-50 dBm
2010 MHz f MHz
1.28MHz
-64dBm
2570 MHz f MHz
1.28MHz
-64dBm
2300 MHz f MHz
1.28MHz
-64dBm
1880 MHz f z
1.28MHz
-64dBm
2110 MHz f MHz
3.84MHz
-60dBm
2620 MHz f MHz
3.84MHz
-60dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
b
1850 MHz f 910 MHz
1.28MHz
-64dBm
1910 MHz f 990 MHz
1.28MHz
-64dBm
c
1910 MHz f 1930MHz
1.28MHz
-64dBm
d
2570 MHz f z
1.28MHz
-64dBm
2010 MHz f z
1.28MHz
-64dBm
2110 MHz f z
3.84MHz
-60dBm
2620 MHz f z
3.84MHz
-60dBm
e
703 MHz f < 803 MHz
1 MHz
-50 dBm
2300 MHz f z
1.28MHz
-64dBm
2010 MHz f z
1.28MHz
-64dBm
1880 MHz f z
1.28MHz
-64dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
f
703 MHz f < 803 MHz
1 MHz
-50 dBm
1880 MHz f z
1.28MHz
-64dBm
2010 MHz f MHz
1.28MHz
-64dBm
2300 MHz f MHz
1.28MHz
-64dBm
2496 MHz f 2690 MHz
1MHz
-50dBm
Note 1: The frequency bandwidth protection 703-803 MHz and 2496-2690 MHz test requirements for Bands a, e and f deviate from the requirements in TS 25.102 [1] Rel-10 and earlier releases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 6.8.5.3 7,68 Mcps TDD Option | The spurious emissions shall be according to table 6.8.5.3 for the 7,68 Mcps TDD Option.
Table 6.8.5.3: Receiver spurious emission test requirements (7,68 Mcps TDD Option)
Band
Maximum level
Measurement Bandwidth
Note
30 MHz - 1 GHz
-57 dBm
100 kHz
1 GHz - 1.9 GHz and
1.92 GHz - 2.01 GHz and
2.025 GHz - 2.11 GHz
2.17 GHz - 2.57 GHz
-47 dBm
1 MHz
1.9 GHz - 1.92 GHz and
2.01 GHz - 2.025 GHz and
2.11 GHz - 2.170 GHz
2.57 Ghz - 2.69 GHz
-57 dBm
7.68 MHz
2.69 GHz - 12.75 GHz
-47 dBm
1 MHz
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in annex F clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in annex F clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7 Performance Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.1 General | The performance requirements for the UE in this clause is specified for the measurement channels specified in annex C and the test environments specified in annex D.
All Block Error ratio (BLER) measurements in clause 7 shall be performed according to the general rules for statistical testing in Annex F.6. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.1.2 Definition of Additive White Gaussian Noise (AWGN) Interferer | The minimum bandwidth of the AWGN interferer shall be 1.5 times chip rate of the radio access mode. (e.g. 5.76 MHz for a chip rate of 3,84 Mcps). The flatness across this minimum bandwidth shall be less than 0.5 dB and the peak to average ratio at a probability of 0.001% shall exceed 10 dB. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2 Demodulation in static propagation conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1 Demodulation of DCH | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.1 Definition and applicability | The performance requirement of DCH in static propagation conditions is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The data-rate-corresponding requirements shall apply to the UE.
The requirements and this test apply to all types of UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.2.1.2.1a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.1.
Table 7.2.1.2.1a: DCH parameters in static propagation conditions (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
dB
-6
-3
0
0
0
Ioc
dBm/3,84 MHz
-60
Cell Parameter*
0,1
DPCH Channelization Codes*
C(k,Q)
C(i,16) i=1,2
C(i,16) i=1 . .5
C(i,16) i=1 . .9
C(i,16) i=1 . .8
-
OCNS Channelization Code*
C(k,Q)
C(3,16)
C(6,16)
-
-
-
Information Data Rate
kbps
12,2
64
144
384
2048
Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.2.1.2.1b: Performance requirements in AWGN channel (3,84 Mcps TDD Option)
Test Number
[dB]
BLER
1
1,1
10-2
2
3,5
10-1
3,8
10-2
3
3,4
10-1
3,6
10-2
4
2,7
10-1
3,0
10-2
5
3,5
10-1
3,6
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.2.1.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.2.
Table 7.2.1.2.2a: DCH parameters in static propagation conditions (1,28Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Number of DPCHo
8
2
2
0
Scrambling code and basic midamble code number*
0
0
0
0
DPCH Channelization Codes*
C(k,Q)
C(i,16)
i=1,2
C(i,16)
i=1…8
C(i,16)
i=1…8
C(i,16)
i=1…9
DPCHo Channelization Codes*
C(k,Q)
C(i,16)
3≤ i ≤10
C(i,16)
9≤ i ≤10
C(i,16)
9≤ i ≤10
-
dB
-10
-10
-10
0
Ioc
dBm/1,28MHz
-60
Midamble
Common midamble
Information Data Rate
Kbps
12.2
64
144
384
*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 7.2.1.2.2b: Performance requirements in AWGN channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
3.6
10-2
2
2.4
10-1
2.7
10-2
3
2.8
10-1
3.2
10-2
4
4.6
10-1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.2.1.2.3a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.2.1.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.2.1.1.3.
Table 7.2.1.2.3a: DCH parameters in static propagation conditions (7,68 Mcps TDD Option)
Parameters
Unit
Test 1
dB
-9
Ioc
dBm/7.68 MHz
-60
Cell Parameter*
-
0,1
DPCH Channelization Codes*
C(k, Q)
C(i, 32), i = 1,2
OCNS Channelization Code*
C(k, Q)
C(3, 32)
Information Data Rate
kbps
12.2
*Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.2.1.2.3b: Performance requirements in AWGN channel (7,68 Mcps TDD Option)
Test Number
[dB]
BLER
1
1.1
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal ,representing a static propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a block error ratio (BLER) not exceeding a specified value. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, AWGN Generator and additional components to the UE antenna connector as shown in figure A.9.
2) A call is set up according to the Generic call setup procedure. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s) (64 kbit/s), (144 kbit/s), and (384 kbit/s) specified in annex C for 3.84 Mcps TDD option and 1.28Mcps TDD option. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s) for 7.68 Mcps TDD option.
3) Enter the UE into loopback test mode and start the loopback test. (test 1) and/or activate the Ack/Nack test mode (test 1 to test 4).
4) The levels of the wanted signal and the co-channel signals are set according to table 7.2.1.2.1a and b for the 3,84 Mcps TDD Option, table 7.2.1.2.2a and b for the 1,28 Mcps TDD Option and table 7.2.1.2.3a and b for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.2.1.2.1a for the 3,84 Mcps TDD Option, table 7.2.1.2.2a for the 1,28 Mcps TDD Option and table 7.2.1.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.5.2 for the1.28 Mcps TDD Option
Table 7.2.1.5.2: Performance requirements in AWGN channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
3.9
10-2
2
2.7
10-1
3.0
10-2
3
3.1
10-1
3.5
10-2
4
4.9
10-1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.2.1.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.2.1.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3 Demodulation of DCH in multipath fading conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1 Multipath fading Case 1 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER). The BLER is specified for each individual data ratio of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data ratios, supported. The data-ratio-corresponding requirements shall apply to the UE.
The requirements and this test apply to all types of UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.1.2.1a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.1.1.1.
Table 7.3.1.2.1a: DCH parameters in multipath Case 1 channel (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
DB
-6
-3
0
0
0
Ioc
dBm/3,84 MHz
-60
Cell Parameter (note)
0,1
DPCH Channelization Codes (note)
C(k,Q)
C(i,16) i=1,2
C(i,16) i=1 . .5
C(i,16) i=1 . .9
C(i,16) i=1 . .8
-
OCNS Channelization Code (note)
C(k,Q)
C(3,16)
C(6,16)
-
-
-
Information Data Rate
kbps
12,2
64
144
384
2048
Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.1.2.1b: Performance requirements in multipath Case 1 channel (3,84 Mcps TDD Option)
Test Number
[dB]
BLER
1
13,9
10-2
2
13,7
10-1
19,8
10-2
3
14,1
10-1
20,6
10-2
4
13,8
10-1
20,0
10-2
5
13,2
10-1
17,8
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.1.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.1.1.2.
Table 7.3.1.2.2a: DCH parameters in a multipath Case 1 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Number of DPCHo
8
2
2
0
Scrambling code and basic midamble code number (see note)
0
0
0
0
DPCH Channelization Codes (see note)
C(k,Q)
C(i,16)
i=1,2
C(i,16)
i=1…8
C(i,16)
i=1…8
C(i,16)
i=1…9
DPCHo Channelization Codes (see note)
C(k,Q)
C(i,16)
3≤ i ≤10
C(i,16)
9≤ i ≤10
C(i,16)
9≤ i ≤10
-
DB
-10
-10
-10
0
Ioc
dBm/1,28MHz
-60
Midamble
Common midamble
Information Data Rate
Kbps
12.2
64
144
384
Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 7.3.1.2.2b: Performance requirements in a multipath Case 1 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
22.4
10-2
2
15.8
10-1
22.9
10-2
3
16.6
10-1
23.9
10-2
4
15.5
10-1
21.4
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.1.2.3a the BLER shall not exceed the piece-wise linear BLER curve specified in table 7.3.1.2.3b. This requirement is applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.1.1.3.
Table 7.3.1.2.3a: DCH parameters in multipath Case 1 channel (7,68 Mcps TDD Option)
Parameters
Unit
Test 1
dB
-9
Ioc
dBm/7.68 MHz
-60
Cell Parameter*
-
0,1
DPCH Channelization Codes*
C(k, Q)
C(i, 32), i = 1,2
OCNS Channelization Code*
C(k, Q)
C(3, 32)
Information Data Rate
kbps
12.2
*Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.1.2.3b: Performance requirements in multipath Case 1 channel (7,68 Mcps TDD Option)
Test Number
[dB]
BLER
1
13.9
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal, representing a multipath propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a block error ratio (BLER) not exceeding a specified value. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, , the fading simulator, the AWGN generator and additional components to the UE antenna connector as shown in figure A.10.
2) A call is set up according to the Generic call setup procedure. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s), (64 kbit/s), (144 kbit/s), and (384 kbit/s) specified in annex C for 3.84 Mcps TDD option and 1.28Mcps TDD option. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s) for 7.68 Mcps TDD option.
3) Enter the UE into loopback test mode and start the loopback test. (test 1) and/or activate the Ack/Nack test mode (test 1 to test 4).
4) The levels of the wanted signal and the co-channel signals are set according to table 7.3.1.2.1a and b for the 3,84 Mcps TDD Option, table 7.3.1.2.2a and b for the 1,28 Mcps TDD Option and table 7.3.1.2.3a and b for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.3.1.2.1a for the 3,84 Mcps TDD Option, table 7.3.1.2.2a for the 1,28 Mcps TDD Option and table 7.3.1.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.5.2b for the1.28 Mcps TDD Option
Table 7.3.1.5.2b: Performance requirements in a multipath Case 1 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
23.0
10-2
2
16.4
10-1
23.5
10-2
3
17.2
10-1
24.5
10-2
4
16.2
10-1
22.0
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.1.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.1.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2 Multipath fading Case 2 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The data-rate-corresponding requirements shall apply to the UE.
The requirements and this test apply to all types of UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.2.2.1a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.
Table 7.3.2.2.1a: DCH parameters in multipath Case 2 channel (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
DB
-3
0
0
0
0
Ioc
dBm/3,84 MHz
-60
Cell Parameter (note)
0,1
DPCH Channelization Codes (note)
C(k,Q)
C(i,16) i=1,2
C(i,16) i=1 . .5
C(i,16) i=1 . .9
C(i,16) i=1 . .8
-
OCNS Channelization Code (note)
C(k,Q)
C(3,16)
-
-
-
-
Information Data Rate
kbps
12,2
64
144
384
2048
Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.2.2.1b: Performance requirements in multipath Case 2 channel (3,84 Mcps TDD Option)
Test Number
[dB]
BLER
1
5,8
10-2
2
5,7
10-1
9,2
10-2
3
9,3
10-1
12,7
10-2
4
8,8
10-1
12,0
10-2
5
10,3
10-1
12,7
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.2.2.2a: the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.2.
Table 7.3.2.2.2a: DCH parameters in multipath Case 2 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Number of DPCHo
8
2
2
0
Scrambling code and basic midamble code number (see note)
0
0
0
0
DPCH Channelization Codes (see note)
C(k,Q)
C(i,16)
i=1,2
C(i,16)
i=1…8
C(i,16)
i=1…8
C(i,16)
i=1…9
DPCHo Channelization Codes (see note)
C(k,Q)
C(i,16)
3≤ i ≤10
C(i,16)
9≤ i ≤10
C(i,16)
9≤ i ≤10
-
dB
-10
-10
-10
0
Ioc
dBm/1,28MHz
-60
Midamble
Common midamble
Information Data Rate
Kbps
12.2
64
144
384
Note Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 7.3.2.2.2b: Performance requirements in multipath Case 2 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
13.6
10-2
2
9.8
10-1
13.9
10-2
3
10.3
10-1
14.4
10-2
4
11.4
10-1
15.0
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.2.2.3a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.2.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 [1] clause 8.3.2.1.3.
Table 7.3.2.2.3a: DCH parameters in multipath Case 2 channel (7,68 Mcps TDD Option)
Parameters
Unit
Test 1
dB
-6
Ioc
dBm/7.68 MHz
-60
Cell Parameter (note)
-
0,1
DPCH Channelization Codes (note)
C(k, Q)
C(i, 32), i = 1,2
OCNS Channelization Code (note)
C(k, Q)
C(3, 32)
Information Data Rate
kbps
12.2
NOTE: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.2.2.3b: Performance requirements in multipath Case 2 channel (7,68 Mcps TDD Option)
Test Number
[dB]
BLER
1
5.8
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.3 Test purpose | While the receiver tests in clause 6 aims for the RF hardware, this performance requirement aims for the receiver's signal processing.
The test purpose is to verify the ability of the receiver to receive a predefined test signal, representing a multipath propagation channel for the wanted and for the co-channel signals from serving and adjacent cells, with a block error ratio (BLER) not exceeding a specified value. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
1) Connect the SS, the fading simulator, the AWGN generator and additional components to the UE antenna connector as shown in figure A.10.
2) A call is set up according to the Generic call setup procedure. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s) (64 kbit/s), (144 kbit/s), and (384 kbit/s) specified in annex C for 3.84 Mcps TDD option and 1.28Mcps TDD option. The characteristic of the call shall be according to the DL reference measurement channels (12,2 kbit/s) for 7.68 Mcps TDD option.
3) Enter the UE into loopback test mode and start the loopback test. (test 1) and/or activate the Ack/Nack test mode (test 1 to test 4).
4) The levels of the wanted signal and the co-channel signals are set according to table 7.3.2.2.1a and b for the 3,84 Mcps TDD Option, table 7.3.2.2.2a and b for the 1,28 Mcps TDD Option and table 7.3.2.2.3a and b for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.4.2 Procedure | Measure the BLER of DCH received from the UE at the SS for all tests specified in table 7.3.2.2.1a for the 3,84 Mcps TDD Option, table 7.3.2.2.2a for the 1,28 Mcps TDD Option and table 7.3.2.2.3a for the 7,68 Mcps TDD Option, respectively. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.1 3.84Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.2.1b for the 3,84 Mcps TDD Option |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.2 1.28Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.5.2b for the1.28 Mcps TDD Option
Table 7.3.2.5.2b: Performance requirements in multipath Case 2 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
14.2
10-2
2
10.4
10-1
14.5
10-2
3
10.9
10-1
15.0
10-2
4
12.0
10-1
15.6
10-2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.2.5.3 7.68Mcps TDD Option | The measured BLER shall not exceed the values indicated in table 7.3.2.2.3b for the 7.68 Mcps TDD Option
NOTE: If the Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3 Multipath fading Case 3 | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.1 Definition and applicability | The performance requirement of DCH is determined by the maximum Block Error Ratio (BLER ). The BLER is specified for each individual data rate of the DCH. DCH is mapped into the Dedicated Physical Channel (DPCH).
The UE shall be tested only according to the data rates, supported. The data-rate-corresponding requirements shall apply to the UE.
The requirements and this test apply to all types of UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2 Minimum requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.1 3,84 Mcps TDD Option | For the parameters specified in table 7.3.3.2.1a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.1b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.3.1.1.
Table 7.3.3.2.1a: DCH parameters in multipath Case 3 channel (3,84 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Test 5
DB
-3
0
0
0
0
Ioc
dBm/3,84 MHz
-60
Cell Parameter (note)
0,1
DPCH Channelization Codes (note)
C(k,Q)
C(i,16) i=1,2
C(i,16) i=1 . .5
C(i,16) i=1 . .9
C(i,16) i=1 . .8
-
OCNS Channelization Code (note)
C(k,Q)
C(3,16)
-
-
-
-
Information Data Rate
kbps
12,2
64
144
384
2048
Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.3.2.1b: Performance requirements in multipath Case 3 channel (3,84 Mcps TDD Option)
Test Number
[dB]
BLER
1
4,8
10-2
2
5,8
10-1
8,5
10-2
10,7
10-3
3
10,3
10-1
13,3
10-2
16,0
10-3
4
8,9
10-1
11,5
10-2
13,6
10-3
5
9,4
10-1
11,5
10-2
13,6
10-3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.2 1,28 Mcps TDD Option | For the parameters specified in table 7.3.3.2.2a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.2b. The reference for this requirement is TS 25.102 [1] clause 8.3.3.1.2.
Table 7.3.3.2.2a: DCH parameters in multipath Case 3 channel (1,28 Mcps TDD Option)
Parameters
Unit
Test 1
Test 2
Test 3
Test 4
Number of DPCHo
8
2
2
0
Scrambling code and basic midamble code number (see note)
0
0
0
0
DPCH Channelization Codes (see note)
C(k,Q)
C(i,16)
i=1,2
C(i,16)
i=1…8
C(i,16)
i=1…8
C(i,16)
i=1…9
DPCHo Channelization Codes (see note)
C(k,Q)
C(i,16)
3≤ i ≤10
C(i,16)
9≤ i ≤10
C(i,16)
9≤ i ≤10
-
dB
-10
-10
-10
0
Ioc
dBm/1,28MHz
-60
Midamble
Common midamble
Information Data Rate
Kbps
12.2
64
144
384
Note Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.
Table 7.3.3.2.2b: Performance requirements in multipath Case 3 channel (1,28 Mcps TDD Option)
Test Number
[dB]
BLER
1
11.7
10-2
2
9.0
10-1
11.7
10-2
14.3
10-3
3
9.1
10-1
11.2
10-2
12.7
10-3
4
9.9
10-1
11.2
10-2
12.4
10-3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 7.3.3.2.3 7,68 Mcps TDD Option | For the parameters specified in table 7.3.3.2.3a the BLER should not exceed the piece-wise linear BLER curve specified in table 7.3.3.2.3b. These requirements are applicable for TFCS size 16.
The reference for this requirement is TS 25.102 clause 8.3.3.1.3.
Table 7.3.3.2.3a: DCH parameters in multipath Case 3 channel (7,68 Mcps TDD Option)
Parameters
Unit
Test 1
dB
-6
Ioc
dBm/7.68 MHz
-60
Cell Parameter*
-
0,1
DPCH Channelization Codes*
C(k, Q)
C(i, 32), i = 1,2
OCNS Channelization Code*
C(k, Q)
C(3, 32)
Information Data Rate
kbps
12.2
*Note: Refer to TS 25.223 for definition of channelization codes and cell parameter.
Table 7.3.3.2.3b: Performance requirements in multipath Case 3 channel (7,68 Mcps TDD Option)
Test Number
[dB]
BLER
1
4.8
10-2 |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.