hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
595
| content
stringlengths 0
6.67M
|
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.4.3 7,68 Mcps Option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.5.1 3,84 Mcps Option | void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.5.2 1,28 Mcps Option | 1) In step c), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 28 s.
3) In step g), the UE shall respond on cell 1.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.5.5.3 7,68 Mcps Option | void
8.2.2.5A Scenario 4B: UTRAN to GSM Cell Re-Selection: HCS with only UTRA level changed
8.2.2.5A.1 Definition and applicability
8.2.2.5A.1.1 3,84 Mcps Option
Void
8.2.2.5A.1.2 1,28 Mcps Option
The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.
The requirements and this test apply to Release 6 and later releases for the combined TDD and GSM UE.
8.2.2.5A.1.3 7,68 Mcps Option
Void
8.2.2.5A.2 Minimum requirement
8.2.2.5A.2.1 3,84 Mcps Option
Void
8.2.2.5A.2.2 1,28 Mcps Option
The cell re-selection delay shall be less than 37.7 s + TBCCH, where TBCCH is the maximum time allowed to read BCCH data from GSM cell, see TS 45.008 [30].
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95 %.
NOTE: The cell re-selection delay can be expressed as: 30 s + TmeasureGSM+DRX cycle length + TBCCH, where:
TmeasureGSM
See Table 4.1 in TS 25.123 section 4.2, 6.4s
DRX cycle length
See Table 4.1 in TS 25.123 section 4.2, 1.28s
TBCCH
Maximum time allowed to read BCCH data from GSM cell, see TS 45.008 [30].
According to [20] and [30], the maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.
This gives a total of 37.68 s + 1.9s, allow 40s in the test case.
The normative reference for this requirement is TS 25.123.
8.2.2.5A.2.3 7,68 Mcps Option
Void
8.2.2.5A.3 Test purpose
This test verifies the UE meets the minimum requirement for the case where the UE camps on a TDD cell and then HCS to a GSM cell.
8.2.2.5A.4 Method of Test
8.2.2.5A.4.1 3,84 Mcps Option
Void
8.2.2.5A.4.2 1,28 Mcps Option
8.2.2.5A.4.2.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected, as given in tables 8.2.2.7.8.1 to 8.2.2.7.8.3. The UE is requested to monitor neighbouring cells on 1 UMTS carrier and 12 GSM cells. Cell 1 and cell 2 shall belong to different Location Areas.
Table 8.2.2.5A.1: General test parameters for UTRAN to GSM Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
1,28 Mcps TDD OPTION cell
Neighbour cell
Cell2
GSM cell
Final condition
Active cell
Cell2
GSM cell
DRX cycle length
s
1,28
HCS
Used
Monitored cell list size
12 GSM neighbours including the ARFCN of cell 2
NOTE: See Annex I for cell information
T1
s
45
T2
s
45
Table 8.2.2.5A.1A: Cell re-selection UTRAN to GSM cell case (cell 1) Scenario 4B
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
dB
13
-12
13
-12
dBm/1,28 MHz
-80
PCCPCH RSCP
dBm
-77
-95
Propagation Condition
AWGN
AWGN
Treselection
s
0
SsearchRAT
dB
Not sent
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
SsearchRAT
dB
0
Penalty_time
s
0 (default value)
HCS_PRIO
0 (default value)
Qhcs
0 (default value)
TCrmax
s
not used (default value)
Table 8.2.2.5A.1B: Cell re-selection UTRAN to GSM cell case (cell 2) Scenario 4B
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-80
-80
RXLEV_ACCESS_MIN
dBm
-104
MS_TXPWR_MAX_CCH
dBm
33
Qsearch_I
-
always
Specific 2 quarter Message Contents
All messages indicated shall use the same content as described in the default message content in TS45.008 [30] clause 9, with the above exceptions.
8.2.2.5A.4.2.2 Procedure
a) The SS activates cell 1 and 2 with T1 defined parameters in tables 8.2.3.3.4 and 8.2.3.3.5 and monitors cell 1 and 2 for random access requests from the UE.
b) The UE is switched on.
c) The SS and the UE shall perform a location registration procedure on cell 1.
d) After 45 s from the end of step 3, the parameters are changed as described for T2 in tables 8.2.3.3.4 and 8.2.3.3.5.
e) The SS waits for a location registration procedure from the UE. If the UE begins transmitting on cell 2 within 39.6 s then the number of successful tests is increased by one.
f) After 45 s from the beginning of T2, the parameters are changed as described for T1 in tables 8.2.3.3.4 and 8.2.3.3.5.
g) The SS and the UE shall perform a location registration procedure on cell 1.
h) After 45 s from the end of step 6, the parameters are changed as described for T2 in tables 8.2.3.3.4 and 8.2.3.3.5.
Repeat step e) to h) until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 6.1.0b of 34.108 [3], with the above and the following exceptions:
SYSTEM INFORMATION BLOCK TYPE3:
Information Element
Value
HCS Serving Cell Information
-HCS PRIO
0
-Qhcs
0
-TCRmax
not used
SYSTEM INFORMATION BLOCK TYPE11
Information Element
Value
HCS neighbouring Cell Information
-HCS PRIO
0
-Qhcs
0
-HCS Cell RE-selection Information
-Penalty_time
0
8.2.2.5A.4.3 7,68 Mcps Option
Void
8.2.2.5A.5 Test Requirements
8.2.2.5A.5.1 3,84 Mcps Option
void
8.2.2.5A.5.2 1,28 Mcps Option
For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95 %.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.2.2.5A.5.3 7,68 Mcps Option
Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6 Scenario 5:TDD/E-UTRA cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1 UTRA to E-UTRA TDD cell reselection: E-UTRA is of higher priority | Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.1 Definition and application | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.1.1 3.84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.1.2 1.28Mcps Option | The cell reselection delay to higher priority is defined as the time from the beginning of time period T2, to the moment when the UE camps on cell2, and start to send preamble on the PRACH for the RRC CONNECTION REQUEST message on cell2.
This test is for case when the UE camps on a 1.28Mcps TDD cell and reselects to a E-UTRA TDD cell which is of higher priority.
The requirement and this test apply to release 9 and later releases UTRA 1.28Mcps TDD UEs that support release 8 and later releases E-UTRA TDD. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.1.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.2.1 3.84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.2.2 1.28Mcps Option | The cell re-selection delay to higher priority shall be less than 81 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay to higher priority cell can be expressed as: Thigher_priority_search + TevaluateE-UTRA + TSI,
Where:
Thigher_priority_search 60s, See 25.123[2] section 4.2.2.5a
TevaluateE-UTRA 19.2s, See 25.123[2] Table 4.2A in section 4.2.2.7
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell; 1280 ms is assumed in this test case.
This gives a total of 80.48 s, allow 81 s for higher priority cell reselection in the test case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.2.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.3 Test purpose | This test verifies the UE meet minimum requirement for the case where the UE camps on a TDD cell and reselects to a E-UTRA TDD cell which is of higher priority. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.1 3.84Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.2 1.28Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.2.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
This test scenario comprised of 1UTRA TDD serving cell, and 1E-UTRA TDD cell to be re-selected. Test parameters are given in table 8.2.2.6.1.4.2.1-1, 8.2.2.6.1.4.2.1-2 and 8.2.2.6.1.4.2.1-3.The test consists of three successive time periods, with time duration of T1, T2 and T3 respectively. UTRA cell1 is already identified by the UE prior to the start of the test. At T1 the UE is camped on to cell1. Cell2 is of higher priority than cell1.
Table 8.2.2.6.1.4.2.1-1: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to E-UTRAN TDD Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
UE is on cell 1 in the initialisation phase, so that reselection to cell 2 occurs during T2
T2 end condition
Active cell
Cell2
UE shall perform reselection to cell 2 during T2
Neighbour cell
Cell1
UTRA 1.28 Mcps TDD OPTION cell
T3 end condition
Active cell
Cell 1
UE shall perform reselection to cell 1 during T3
Neighbour cell
Cell 2
E-UTRA TDD cell
Uplink-downlink configuration of cell 2
1
As specified in table 4.2.2 in TS 36.211 [30]
Special subframe configuration of cell 2
6
As specified in table 4.2.1 in TS 36.211 [30]
PRACH configuration of cell 2
53
As specified in table 4.7.1-3 in TS 36.211 [30]
CP length of cell 2
Normal
Time offset between cells
3 ms
Asynchronous cells
Access Barring Information
-
Not sent
No additional delays in random access procedure.
Treselection
s
0
DRX cycle length
s
1,28
HCS
Not used
T1
s
>20
During T1, cell 2 shall be powered off, and during the off time its physical cell identity shall be changed. The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2.
T2
85
T2 needs to be defined so that cell re-selection reaction time is taken into account.
T3
s
25
T3 needs to be defined so that cell re-selection reaction time is taken into account.
Table 8.2.2.6.1.4.2.1-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number (Note1)
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
dB
11
11
11
11
11
11
dBm/1.28 MHz
-80
PCCPCH RSCP
dBm
-72
-72
-72
n.a.
Propagation Condition
AWGN
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
Threshx, high (Note2)
dB
46 (-94dBm)
Sprioritysearch1
dB
24
Sprioritysearch2
dB
0
SsearchE-UTRA
dB
Not sent
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Note2: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell
Table 8.2.2.6.1.4.2.1-3: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)
Parameter
Unit
Cell 2
T1
T2
T3
E-UTRA RF Channel Number
2
BWchannel
MHz
10
OCNG Pattern defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
PBCH_RA
dB
0
0
0
PBCH_RB
dB
PSS_RB
dB
SSS_RB
dB
PCFICH_RA
dB
PHICH_RA
dB
PHICH_RA
dB
PDCCH_RA
dB
PDCCH_RA
dB
PDSCH_RA
dB
PDSCH_RA
dB
OCNG_RA (Note 1)
dB
OCNG_RB (Note 1)
dB
Qrxlevmin
dBm/15kHz
-140
-140
-140
dBm/15kHz
-98
dB
-inf
11
-3
RSRP
dBm/15kHz
-inf
-87
-101
dB
-inf
11
-3
Snonintrasearch
dB
Not sent
Threshserving, low
dB
46 (-94dBm)
Threshx, low (Note2)
dB
24 (-79dBm)
Propagation Condition
AWGN
Note 1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.2.2 Procedure | 1) The SS activates cell 1 with T1 defined parameters in tables 8.2.2.6.1.5.2-1 and, and monitors cell 1 for random access requests from the UE.
2) The UE is switched on.
3) The SS and the UE shall perform a location registration procedure on cell 1 and apply the cell 2 parameters with T1 defined in table 8.2.2.6.1.5.2-2. T1 starts.
4) After T1 expires, the parameters are changed as described for T2 in tables 8.2.2.6.1.5.2-1 and 8.2.2.6.1.5.2-2.
5) The SS waits for random access request information from the UE to perform cell re-selection procedure on cell 2.
6) If the UE camps on cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure or an Attach Procedure for Rel-10 and higher UEs according to TS 36.508 [7] clause 7.2B.1 on cell 2 within 81 s then the number of successful tests is increased by one. Otherwise, the number of failure tests is increased by one.
7) After the re-selection or when T2 expires, the parameters are changed as described for T3 as specified in tables 8.2.2.6.1.5.2-1 and 8.2.2.6.1.5.2-2.If the UE failed to complete a Tracking Area Update procedure or an Attach Procedure for Rel-10 and higher UEs according to TS 36.508 [7] clause 7.2B.1 on cell 2 in step 6), then switch OFF the UE and go to step 1).
8) The SS and the UE shall perform a location registration procedure on cell 1.
9) After the re-selection or when T3 expires, the parameters are changed as described for T1 in tables 8.2.2.6.1.5.2-1 and 8.2.2.6.1.5.2-2. During T1, Cell 2 shall be powered off and the SS shall set Cell 2 physical cell identity = ((current cell 2 physical cell identity +1) mod 14 + 2).
10) If the UE failed to complete the location registration procedure on cell 1 in step 8), then switch OFF the UE and go to step 1).
11) When T1 expires, the parameters are changed as described for T2 in tables 8.2.2.6.1.5.2-1 and 8.2.2.6.1.5.2-2.
12) Repeat steps 5) to 11) until the confidence level according to Tables G.2.3-1 in TS 36.521-3 [33] is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.2.3 Message contents | All messages indicated above shall use the same content as described in the default message content in TS 36.508 [28] clause 4.4 and 4.6 with the following exceptions:
SystemInformationBlockType19: for inter-RAT UTRA TDD - EUTRAN TDD is of higher priority cell re-selection
Derivation Path: TS 36.508 [28] clause 4.4.4.1, Table 4.4.4.1-1 SystemInformationBlockType19
Information Element
Value/remark
Comment
Condition
SysInfoType19 ::= SEQUENCE {
utran-TDD-FrequencyList SEQUENCE (SIZE(1..maxNumTDDFreqs)) OF SEQUENCE {
Priority
3
UTRA is of lower priority
s-PrioritySearch1
24
s-PrioritySearch2
0
}
eutra-FrequencyAndPriorityInfoList SEQUENCE (SIZE (1..maxNumEUTRAFreqs)) OF SEQUENCE {
n denotes the index of the entry
Priority
5
E-UTRA is of higher priority
qRxLevMinEUTRA
-70 (-140 dBm)
Threshx, high
46 dB
}
}
PRACH-ConfCommonDEFAULT: (TDD) for Inter-RAT cell re-selection
Derivation Path: TS 36.508 [28] clause 4.6.3, Table 4.6.3-7 PRACH-ConfCommonDEFAULT
Information Element
Value/remark
Comment
Condition
PRACH-ConfigInfo SEQUENCE {
prach-ConfigIndex
53
} |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.4.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.5 Test requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.5.1 3.84Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.5.2 1.28Mcps Option | Table 8.2.2.6.1.5.2-1: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number (Note1)
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
dB
11
11
11
11
11
11
dBm/1.28 MHz
-80
PCCPCH RSCP
dBm
-72
-72
-72
n.a.
Propagation Condition
AWGN
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
Threshx, high (Note2)
dB
46 (-94dBm)
Sprioritysearch1
dB
24
Sprioritysearch2
dB
0
SsearchE-UTRA
dB
Not sent
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Note2: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell
Table 8.2.2.6.1.5.2-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)
Parameter
Unit
Cell 2
T1
T2
T3
E-UTRA RF Channel Number
2
BWchannel
MHz
10
OCNG Pattern defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
PBCH_RA
dB
0
0
0
PBCH_RB
dB
PSS_RA
dB
SSS_RA
dB
PCFICH_RB
dB
PHICH_RA
dB
PHICH_RB
dB
PDCCH_RA
dB
PDCCH_RB
dB
PDSCH_RA
dB
PDSCH_RB
dB
OCNG_RA (Note 1)
dB
OCNG_RB (Note 1)
dB
Qrxlevmin
dBm
-140
-140
-140
dBm/15kHz
-98
dB
-inf
11
-3
RSRP
dBm/15kHz
-inf
-87
-101
dB
-inf
11
-3
Snonintrasearch
dB
Not sent
Threshserving, low
dB
46 (-94dBm)
Threshx, low (Note2)
dB
24 (-79dBm)
Propagation Condition
AWGN
Note 1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell
For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.1.5.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2 UTRA to E-UTRA TDD cell reselection: E-UTRA is of lower priority | Editor’s note: This Test case is incomplete for frequencies above 3GHz
• The Test system uncertainties applicable above 3GHz are undefined
• The Test Tolerances and Test Requirements applicable above 3GHz are undefined |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.1 Definition and application | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.1.1 3.84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.1.2 1.28Mcps Option | The cell reselection delay to low priority is defined as the time from the beginning of time period T2, to the moment when the UE camps on cell2, and start to send preamble on the PRACH for the RRC CONNECTION REQUEST message on cell2.
This test is for case when the UE camps on a 1.28Mcps TDD cell and reselects to a E-UTRA TDD cell which is of lower priority.
The requirement and this test apply to release 9 and later releases UTRA 1.28Mcps TDD UEs that support release 8 and later releases E-UTRA TDD. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.1.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.2.1 3.84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.2.2 1.28Mcps Option | The cell re-selection delay to lower priority shall be less than 21 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay to lower priority cell can be expressed as: TevaluateE-UTRA + TSI,
Where:
TevaluateE-UTRA 19.2s, See Table 4.2A in section 4.2.2.7 in 25.123
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell; 1280 ms is assumed in this test case.
This gives a total of 20.48 s, allow 21 s for lower priority cell reselection in the test case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.2.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.3 Test purpose | This test verifies the UE meet minimum requirement for the case where the UE camps on a TDD cell and reselects to a E-UTRA TDD cell which is of lower priority. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.1 3.84Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.2 1.28Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.2.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: see table J.2 in Annex J.
This test scenario comprised of 1 UTRA TDD serving cell ,and 1 E-UTRA TDD cell to be re-selected.Test parameters are given in table 8.2.2.6.2.4.2.1-1, 8.2.2.6.2.4.2.1-2 and 8.2.2.6.2.4.2.1-3. The test consisits of two successive time periods,with time duration of T1 and T2 respectively. At T1 the UE is camped on to cell1. Cell2 is of lower priority than cell1.
Table 8.2.2.6.2.4.2.1-1: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to E-UTRAN TDD Cell Re-selection
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell 1
UTRA 1.28 Mcps TDD option cell
T1 end condition
Active cell
Cell1
UE shall perform reselection to cell 1 during T1 for subsequent iterations of the test.
Neighbour cell
Cell2
E-UTRA TDD cell
T2 end condition
Active cell
Cell2
UE shall perform reselection to cell 2 during T2
Neighbour cell
Cell1
UTRA 1.28 Mcps TDD OPTION cell
Uplink-downlink configuration of cell 2
1
As specified in table 4.2.2 in TS 36.211 [30]
Special subframe configuration of cell 2
6
As specified in table 4.2.1 in TS 36.211 [30]
PRACH configuration of cell 2
53
As specified in table 4.7.1-3 in TS 36.211 [30]
CP length of cell 2
Normal
Time offset between cells
3 ms
Asynchronous cells
Access Barring Information
-
Not sent
No additional delays in random access procedure.
Treselection
s
0
DRX cycle length
s
1,28
HCS
Not used
T1
s
85
T1 need to be defined so that cell re-selection reaction time is taken into account.
T2
s
25
T2 need to be defined so that cell re-selection reaction time is taken into account.
Table 8.2.2.6.2.4.2.1-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number (Note1)
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
OCNS_Ec/Ior
dB
-3
-3
dB
11
-3
11
-3
dBm/1.28 MHz
-80
PCCPCH RSCP
dBm
-72
-86
n.a.
n.a.
Propagation Condition
AWGN
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
Threshserving, low
dB
24 (-79dBm)
Threshx, low (Note2)
dB
46 (-94dBm)
Sprioritysearch1
dB
62
Sprioritysearch2
dB
0
SsearchE-UTRA
dB
Not send
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Note2: This refers to the value of Threshx, low which is included in UTRA system information, and is a threshold for the E-UTRA target cell
Table 8.2.2.6.2.4.2.1-3: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)
Parameter
Unit
Cell 2
T1
T2
E-UTRA RF Channel Number
2
BWchannel
MHz
10
OCNG Pattern defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
PBCH_RA
dB
0
0
PBCH_RB
dB
PSS_RB
dB
SSS_RB
dB
PCFICH_RA
dB
PHICH_RA
dB
PHICH_RA
dB
PDCCH_RA
dB
PDCCH_RA
dB
PDSCH_RA
dB
PDSCH_RA
dB
OCNG_RA (Note1)
dB
OCNG_RB (Note1)
dB
Qrxlevmin
dBm/15kHz
-140
-140
dBm/15kHz
-98
RSRP
dBm/15kHz
-87
-87
dB
11
11
Threshx, high (Note2)
dB
24(-79dBm)
Snonintrasearch
dB
46
Propagation Condition
AWGN
Note1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note2: This refers to the value of Threshx, high which is included in E-UTRA system information, and is a threshold for the UTRA target cell |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.2.2 Procedure | 1) The SS activates cell1 with T1 defined parameters in tables 8.2.2.6.2.5.2-1 and monitors cell1 for random access requests from the UE.
2) The UE is switched on.
3) The SS and the UE shall perform a location registration procedure on cell1 and apply the cell 2 parameters with T1 defined in table 8.2.2.6.2.5.2-2. T1 starts.
4) After the re-selection or when T1 expires, the parameters are changed as described for T2 in tables 8.2.2.6.2.5.2-1 and 8.2.2.6.2.5.2-2.
5) The SS waits for random access request information from the UE to perform cell re-selection procedure on cell 2.
6) If the UE camps on cell 2 and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure or an Attach Procedure for Rel-10 and higher UEs according to TS 36.508 [7] clause 7.2B.1 on cell 2 within 21 s, then the number of successful tests is increased by one. Otherwise, the number of failure tests is increased by one.
7) After the re-selection or when T2 expires, the parameters are changed as defined for T1 in tables 8.2.2.6.2.5.2-1 and 8.2.2.6.2.5.2-2. If the UE failed to complete a Tracking Area Update procedure or an Attach Procedure for Rel-10 and higher UEs according to TS 36.508 [7] clause 7.2B.1 on cell 2 in step 6), then switch OFF the UE and go to step 1).
8) The SS and the UE shall perform a location registration procedure on cell 1.
9) If the UE failed to complete the location registration procedure on cell 1 in step 8), then switch OFF the UE and go to step 1).
10) Repeat steps 4) to 9) until the confidence level according to Tables G.2.3-1 in TS 36.521-3 [33] is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.2.3 Message contents | All messages indicated above shall use the same content as described in the default message content in TS 36.508 [28] clause 4.4 and 4.6 with the following exceptions:
SystemInformationBlockType19: for inter-RAT UTRA TDD - EUTRAN TDD is of lower priority cell re-selection
Derivation Path: TS 36.508 [28] clause 4.4.4.1, Table 4.4.4.1-1 SystemInformationBlockType19
Information Element
Value/remark
Comment
Condition
SysInfoType19 ::= SEQUENCE {
utra-PriorityInfoList SEQUENCE {
utra-ServingCell SEQUENCE {
Priority
5
UTRA is of higher priority
s-PrioritySearch1
62
Maximum value
s-PrioritySearch2
0
threshServingLow
24 dB
}
eutra-FrequencyAndPriorityInfoList SEQUENCE (SIZE (1..maxNumEUTRAFreqs)) OF SEQUENCE
priority
3
E-UTRA is of lower priority
qRxLevMinEUTRA
-70 (-140 dBm)
Threshx, low
46 dB
}
}
PRACH-ConfCommonDEFAULT: (FDD) for Inter-RAT cell re-selection
Derivation Path: TS 36.508 [28] clause 4.6.3, Table 4.6.3-7 PRACH-ConfCommonDEFAULT
Information Element
Value/remark
Comment
Condition
PRACH-ConfigInfo SEQUENCE {
prach-ConfigIndex
53
} |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.4.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.5 Test requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.5.1 3.84Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.5.2 1.28Mcps Option | Table 8.2.2.6.2.5.2-1: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number (Note1)
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
OCNS_Ec/Ior
dB
-3
-3
dB
11
-3
11
-3
dBm/1.28 MHz
-80
PCCPCH RSCP
dBm
-72
-86
n.a.
n.a.
Propagation Condition
AWGN
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
Threshserving, low
dB
24 (-79dBm)
Threshx, low (Note2)
dB
46 (-94dBm)
Sprioritysearch1
dB
62
Sprioritysearch2
dB
0
SsearchE-UTRA
dB
Not send
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.
Note2: This refers to the value of Threshx, low which is included in UTRA system information, and is a threshold for the E-UTRA target cell
Table 8.2.2.6.2.5.2-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)
Parameter
Unit
Cell 2
T1
T2
E-UTRA RF Channel Number
2
BWchannel
MHz
10
OCNG Pattern defined in D.2.2 (OP.2 TDD) in TS 36.521-3 [33]
OP.2 TDD
PBCH_RA
dB
0
0
PBCH_RB
dB
PSS_RA
dB
SSS_RA
dB
PCFICH_RB
dB
PHICH_RA
dB
PHICH_RB
dB
PDCCH_RA
dB
PDCCH_RB
dB
PDSCH_RA
dB
PDSCH_RB
dB
OCNG_RA (Note1)
dB
OCNG_RB (Note1)
dB
Qrxlevmin
dBm
-140
-140
dBm/15kHz
-98
RSRP
dBm/15kHz
-87
-87
dB
11
11
Threshx, high (Note2)
dB
24(-79dBm)
Snonintrasearch
dB
46
Propagation Condition
AWGN
Note1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols.
Note2: This refers to the value of Threshx, high which is included in E-UTRA system information, and is a threshold for the UTRA target cell
For the test to pass, the total number of successful tests shall be at least 90% of the cases with a confidence level of 95%.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.6.2.5.3 7.68Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7 Scenario 6: Inter-band Cell Re-selection for 1.28 Mcps TDD UE | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.1 Definition and applicability | The cell re-selection delay is defined as the time from a change of cell parameters to the moment when the UE camps on a new cell, and starts to send SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on the new cell.
The requirements and this test apply to all types of 1.28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.2 Minimum requirement | The cell re-selection delay shall be less than 8 s. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.3 Test purpose | This test is to verify the requirement for the cell re-selection delay in the cross frequency band case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
Cell condition:
There are six cells. Two frequency points are in frequency band a and frequency band b respectively. (The cells are two service cells and four background cells. The service cells use different frequencies. Every two background cells use the same frequency.)
Signal propagation condition: AWGN
Test instrument: Noise source
Table 8.2.2.7.4.1-1 General test parameters for inter-frequency cell re-selection
Parameter
Unit
Value
Remarks
Initial conditions
Active cell
Cell1
Neighbour cell
Cell2, Cell3, Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
Qrxlevmin
dBm
–103
Access Service Class (ASC#0)
‑ Persistence value
1
TSI
s
1.28
DRX cycle length
s
1.28
T1
s
30
T2
s
15
Table 8.2.2.7.4.1-2 Cell settings for inter-frequency cell re-selection
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number (Note 1)
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
–3
–3
–3
–3
–3
–3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
–3
–3
–3
–3
–3
–3
dB
10
4
10
4
4
10
4
10
–1
–1
–1
–1
PCCPCH RSCP
dBm
–63
–69
–69
–63
–74
–74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1, C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2, C4:0C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3, C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number (Note 1)
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
–3
–3
–3
–3
–3
–3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
–3
–3
–3
–3
–3
–3
dB
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
–1
PCCPCH RSCP
dBm
–74
–74
–74
–74
–74
–74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4, C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5, C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6, C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/1.28 MHz
–70
Propagation Condition
AWGN
Note 1: Channel 1 is in frequency band a, and channel 2 is in frequency band f.
NOTE: The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
To evaluate NTDD: A DRX cycle length of 1280 ms is assumed for this test case, and this leads to a TevaluateNTDD of 6.4 s according to "Appendix F."
TSI: Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks for a UTRAN cell (ms). 1280 ms is assumed in this test case.
This gives a total of 7.68s, allow 8s in the test case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.4.2 Procedure | 1) The SS activates cells 1–6 with T1 defined parameters and monitors cells 1 and 2 for RRC CONNECTION REQUEST messages from the UE.
2) The UE is switched on.
3) The SS waits until the UE camps on Cell 1 and sends the RRC CONNECTION REQUEST message.
4) After 15 seconds, the SS shall switch the power settings from T1 to T2.
5) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
6) After another 15 seconds, the SS shall switch the power settings as described for T1.
7) The SS waits for SYNCH-UL sequence in the UpPTS for sending RRC CONNECTION REQUEST messages from the UE.
8) Repeat steps 2 to 7 until the required confidence level is achieved.
NOTE: T1 is initially 30s to allow enough time for the UE to search for cells. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.2.2.7.5 Test Requirements | The cell re-selection delay shall be less than 8s.
The rate of correct cell reselections observed during repeated tests shall be at least 90% with a confidence level of 95%.
In step 3, after the UE has responded on cell 1, it shall not respond on any other cell.
In step 5, the UE shall respond on cell 2 within eight seconds.
In step 7, the UE shall respond on cell 1 within eight seconds. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3 UTRAN Connected Mode Mobility | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1 TDD/TDD Handover for 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1 Handover to intra-frequency cell | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.1 Definition and applicability | Handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCH.
The requirements and this test apply to the UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.2 Minimum requirement | The interruption time shall be less than 40 ms in the single carrier case when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/TDD intra-frequency handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+TUL+30*FSFN+20*KC+180*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell and the time that can elapse until the appearance of a Beacon channel
TUL Equal to 10 ms, the time that can elapse until the appearance of the UL timeslot in the target cell
FSFN Equal to 1 if SFN decoding is required and equal to 0 otherwise
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
An intra-frequency TDD target cell shall be considered as known by the UE, if either or both of the following conditions are true:
- the target cell has been measured during the last 5 seconds
- the UE has had a radio link connected to the target cell during the last 5 seconds.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.1. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.3 Test purpose | The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the single carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1.1.1 and 8.3.1.1.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table 8.3.1.1.1: General test parameters for Handover to intra-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
T1
s
10
T2
s
10
T3
s
10
Table 8.3.1.1.2: Cell specific test parameters for Handover to intra-frequency cell
Parameter
Unit
Cell 1
Cell 2
DL timeslot number
0
4
0
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
-9
n.a.
SCH_toffset
dB
0
n.a.
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
n.a.
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
n.a.
-3,12
n.a.
Note 2
dB
1
-Inf.
3
-Inf.
3
PCCPCH RSCP
dBm
-72
n.a.
-Inf.
-70
n.a.
dBm/3,84 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
[Editor's note: subclause 7.3.4 in TS 34.108 (Message sequence chart for Handover Test procedure) is not yet specified]
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCH to cell 2 less than 40 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 10 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps TDD
-UL Target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
3,84 Mcps TDD
-Indivdual Timeslot interference info
1
-Individual timeslot interference (10.3.6.38)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
3,84 Mcps TDD
-Timeslot number
12
-UL Timeslot Interference
-90 dBm
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
TBD dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
3,84 Mcps
-Timeslot number
12
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
3,84 Mcps
-Choice Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
3,84 Mcps
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps
-TX Diversity mode (10.3.6.86)
None
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps
-CHOICE sync case
Case 2
-Timeslot
0
-Cell parameters ID
20
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
3,84 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
3,84 Mcps
-CHOICE Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
3,84 Mcps
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Checked that this IE is present
-CHOICE mode
TDD
-Cell parameters ID
20
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
40 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.1.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]% of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2 Handover to inter-frequency cell | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.1 Definition and applicability | The handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCH.
The requirements and this test apply to the UTRA TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.2 Minimum requirement | The interruption time shall be less than 40 ms in the dual carrier case when the cell is known by the UE and the SFN of the target cell needs to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/TDD inter-frequency handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+TUL+30*FSFN+20*KC+180*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell and the time that can elapse until the appearance of a Beacon channel
TUL Equal to 10 ms, the time that can elapse until the appearance of the UL timeslot in the target cell
FSFN Equal to 1 if SFN decoding is required and equal to 0 otherwise
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
An inter-frequency TDD target cell shall be considered as known by the UE, if either or both of the following conditions are true:
- the target cell has been measured during the last 5 seconds
- the UE has had a radio link connected to the target cell during the last 5 seconds.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.3 Test purpose | The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state in the dual carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1.2.1 and 8.3.1.2.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at beginning of T3 with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table 8.3.1.2.1: General test parameters for Handover to inter-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Hysteresis parameter for event 2C
Time to Trigger
ms
0
Threshold non-used frequency
dBm
-80
Applicable for Event 2C
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
10
T2
s
10
T3
s
10
Table 8.3.1.2.2: Cell Specific parameters for Handover to inter-frequency cell
Parameter
Unit
Cell 1
Cell 2
DL timeslot number
0
4
2
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
-9
n.a.
SCH_toffset
dB
0
n.a.
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
n.a.
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
n.a.
-3,12
n.a.
Note 2
dB
1
-Inf.
7
-Inf
7
PCCPCH RSCP
dBm
-72
n.a.
-Inf.
-66
n.a.
dBm/3,84 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
[Editor's note: subclause 7.3.4 in TS 34.108 (Message sequence chart for Handover Test procedure) is not yet specified]
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCH to cell 2 less than 40 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 10 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
MEASUREMENT CONTROL message, event 2C (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No Report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-80 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps TDD
-UL Target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
3,84 Mcps TDD
-Indivdual Timeslot interference info
1
-Individual timeslot interference (10.3.6.38)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
3,84 Mcps TDD
-Timeslot number
12
- UL Timeslot Interference
-90 dBm
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
TBD dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
3,84 Mcps
-Timeslot number
12
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
3,84 Mcps
-CHOICE Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
3,84 Mcps
-First timeslot code list
1
-Channelisation code
8/1
-CHOICE more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps
-TX Diversity mode (10.3.6.86)
None
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
- CHOICE mode
TDD
- CHOICE TDD option
3,84 Mcps
- CHOICE sync case
Case 2
- Timeslot
2
- Cell parameters ID
20
- SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
- DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
- Downlink DPCH timeslots and codes (10.3.6.32)
- First individual timeslot info (10.3.6.37)
- Timeslot Number (10.3.6.84)
- CHOICE TDD option
3,84 Mcps
- Timeslot number
5
- TFCI existence
True
- Midamble shift and burst type (10.3.6.41)
- CHOICE TDD option
3,84 Mcps
- CHOICE Burst Type
Type 1
- Midamble Allocation Mode
Default
- Midamble configuration burst type 1 and 3
16
- Midamble shift
Not present
- CHOICE TDD option
3,84 Mcps
- First timeslot channelisation codes (10.3.6.17)
- CHOICE codes representation
Consecutive codes
- First channelisation code
16/1
- Last channelisation code
16/2
- CHOICE more timeslots
No more timeslots
- SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2 in Table 8.6.2.4.1.2
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Checked that this IE is present
-CHOICE mode
TDD
-Cell parameters ID
Set to cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2C
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2 in Table 8.6.2.4.1.2
-CHOICE mode
TDD
-Primary CCPCH Info
-CHOICE mode
TDD
-CHOICE TDD Option
3,84 Mcps TDD
-CHOICE Sync Case
Not Present
-Cell Parameters ID
Set to cell parameters ID of Cell 2
-SCTD Indicator
FALSE |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.1.2.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]% of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A TDD/TDD Handover for 1,28 Mcps Option
8.3.1A.1 Handover to intra-frequency cell
8.3.1A.1.1 Scenario 1
This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to primary frequency in multi-frequency network
8.3.1A.1.1.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.1.1.2 Minimum requirement
The hard handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.1.1.3 Test purpose
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state.
8.3.1A.1.1.4 Method of test
8.3.1A.1.1.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1A.1.1.1 and 8.3.1A.1.1.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time ”now” with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.1.1.1: General test parameters for Handover to intra-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multi-frequency network, UE will handover to the primary frequency in cell 2.
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
T1
s
5
T2
s
5
T3
s
5
Table 8.3.1A.1.1.2: Cell specific test parameters for Handover to intra-frequency cell 1,28Mcps option
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(NOTE3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
6
-Inf.
6
-Inf.
6
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-67
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number.
8.3.1A.1.4.1.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 5 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by oneUE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Intra frequency test cases
This message is common for all intra frequency test cases in clause 8.7 and is described in Annex I.
8.3.1A.1.1.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A.1.2 Scenario 2
This test case is applicable for UE handovers from primary frequency to secondary frequency in the case of multi-frequency network.
8.3.1A.1.2.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.1.2.2 Minimum requirement
The hard handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.1.2.3 Test purpose
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state.
8.3.1A.1.2.4 Method of test
8.3.1A.1.2.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1A.1.2.1 and 8.3.1A.1.2.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 2C. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time ”now” with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.1.2.1: General test parameters for Handover to intra-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
The UE has a RRC connection on the secondary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
The UE will handover to the primary frequency in cell 2.
Hysteresis
dB
0
Threshold non-used frequency
dBm
-75
Absolute threshold RSCP for Event 2C
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
T1
s
5
T2
s
5
T3
s
5
Table 8.3.1A.1.2.2: Cell specific test parameters for Handover to intra-frequency cell 1,28Mcps option
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(NOTE3)
Channel 2
UTRA RF Channel Number(NOTE4)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
4
-Inf.
4
-Inf.
4
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-69
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number.
Note 4: In the case of multi-frequency network, the UTRA RF Channel Number is the secondary frequency’s channel number
8.3.1A.1.2.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 5 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by oneUE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
Type 1
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-75 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Intra frequency test cases
This message is common for all intra frequency test cases in clause 8.7 and is described in Annex I.
8.3.1A.1.2.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A.2 Handover to inter-frequency cell
8.3.1A.2.1 Scenario 1
This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to the primary frequency in multi-frequency network.
8.3.1A.2.1.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.2.1.2 Minimum requirement
The hard handover delay shall be less than 160ms when the cell is known by the UE and the SFN of the target cell needs to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.2.1.3 Test purpose
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state.
8.3.1A.2.1.4 Method of test
8.3.1A.2.1.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1A.2.1.1 and 8.3.1A.2.1.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time"now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C , The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.2.1.1: General test parameters for Handover to inter-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multi-frequency network, the UE will handover to the primary frequency in cell 2.
Threshold non-used frequency
dBm
-75
Absolute threshold RSCP for Event 2C
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.3.1A.2.1.2: Cell Specific parameters for Handover to inter-frequency cell
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
4
-Inf.
4
-Inf.
4
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-69
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number.
8.3.1A.2.1.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by one.UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message, event 2C (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
Type 1
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-75 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
now
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
-1,28 Mcps TDD
-TPC stepsize
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-CHOICE more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
- CHOICE mode
TDD
- CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
- Cell parameters ID
0
- SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
- DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
- Downlink DPCH timeslots and codes (10.3.6.32)
- First individual timeslot info (10.3.6.37)
- Timeslot Number (10.3.6.84)
- CHOICE TDD option
1,28 Mcps
- Timeslot number
5
- TFCI existence
True
- Midamble shift and burst type (10.3.6.41)
- CHOICE TDD option
1,28 Mcps
- Midamble Allocation Mode
Default
- Midamble configuration
16
- Midamble shift
Not present
- CHOICE TDD option
1,28 Mcps
- First timeslot channelisation codes (10.3.6.17)
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
- CHOICE codes representation
Consecutive codes
- First channelisation code
16/1
- Last channelisation code
16/2
- CHOICE more timeslots
No more timeslots
- SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Inter frequency test cases
This message is common for all inter frequency TDD test cases in clause 8.7 and is described in Annex I.
8.3.1A.2.1.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A.2.2 Scenario 2
This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to the secondary frequency in multi-frequency network.
8.3.1A.2.2.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.2.2.2 Minimum requirement
The hard handover delay shall be less than 160ms when the cell is known by the UE and the SFN of the target cell needs to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.2.2.3 Test purpose
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state.
8.3.1A.2.2.4 Method of test
8.3.1A.2.2.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1A.2.2.1 and 8.3.1A.2.2.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 1G reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time"now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G , The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.2.2.1: General test parameters for Handover to inter-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multi-frequency network, the UE will handover to the secondary frequency in cell 2.
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.3.1A.2.2.2: Cell Specific parameters for Handover to inter-frequency cell
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
UTRA RF Channel Number(Note 4)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
6
-Inf.
6
-Inf.
6
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-67
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number.
Note 4: In the case of multi-frequency network, the UTRA RF Channel Number is the secondary frequency’s channel number.
8.3.1A.2.2.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by one.UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message, event 2C (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Inter frequency test cases
This message is common for all inter frequency TDD test cases in clause 8.7 and is described in Annex I.
8.3.1A.2.2.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A.3 Handover to inter-band cell
8.3.1A.3.1 Scenario 1
This test case is applicable for UE handovers from primary frequency to the primary frequency in multi-band network.
8.3.1A.3.1.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying handover to the transmission of the SYNC-UL, including the RRC procedure delay as defined in [9].
The requirements and this test apply to all types of 1.28 Mcps TDD UE.
8.3.1A.3.1.2 Minimum Requirements
The inter-frequency hard handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded.
8.3.1A.3.1.3 Test purpose
The purpose of this test is to verify that the hard handover success rate from primary frequency to primary frequency of the UE in CELL_DCH state meets the requirements of the specifications. (Here, the handover success means that the handover delay meets the related requirements.)
8.3.1A.3.1.4 Method of test
8.3.1A.3.1.4.1 Initial conditions
Test environment: normal,; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
Cell condition: In cell 1, the primary frequency uses frequency b of band a, and the secondary frequency uses frequencies a and c. In cell 2, the primary frequency uses frequency e of band f, and the secondary frequency uses frequencies d and f.
Signal propagation condition: AWGN
Test instrument: Noise source
The test parameters are given in table1 and table2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The P-CCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.3.1 General test parameters for TD-SCDMA/TD-SCDMA primary frequency -> primary frequency hard handover (cross frequency band)
Parameter
Unit
Value
Remarks
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbit/s
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
Threshold non-used frequency
dBm
–75
Threshold RSCP for Event 2C
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TD-SCDMA neighbours on Channel 1
6 TD-SCDMA neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.3.1A.3.2 Cell specific test parameters for TD-SCDMA/TD-SCDMA primary frequency -> primary frequency hard handover (cross frequency band)
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number (Note 2)
Channel 1
PCCPCH_Ec/Ior
dB
–3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note 1
n.a.
dB
–3
dB
3
3
3
dBm/1.28 MHz
–70
PCCPCH_RSCP
dBm
–70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number (Note 2)
Channel 2
PCCPCH_Ec/Ior
dB
–3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note 1
dB
–3
dB
–Inf.
4
–Inf.
4
–Inf.
4
dBm/1.28 MHz
–70
PCCPCH_RSCP
dBm
–Inf.
–69
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop.
Note 2: In the case of multi-frequency network, the UTRA RF Channel Number is the channel number of the primary frequency.
8.3.1A.3.1.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in 3GPP TS 34.108 [3] sub-clause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After five seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time "now".
8) After 10 seconds, the SS shall switch the power settings from T2 to T3.
9) If the UE transmits the SYNC-UL to cell 2 less than 160 ms from the beginning of time period T3, then the number of successful tests is increased by one. UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After five seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps 1 to 10 until the required confidence level is achieved.
All messages indicated above shall use the same content as described in the default message content in clause 9 of TS34.108 with the following exceptions:
MEASUREMENT CONTROL message (step 4)
Information Element/Group Name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting/Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TD-SCDMA
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
Type 1
-Cell synchronization information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TD-SCDMA
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
–75 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7)
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
now
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronization info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TD-SCDMA
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TD-SCDMA
-CHOICE TD-SCDMA option
TD-SCDMA
-UL target SIR
–80 dBm
-CHOICE UL OL PC info
Individually signalled
-CHOICE TD-SCDMA option
TD-SCDMA
-TPC stepsize
1
- UL Timeslot Interference
–90 dBm
-CHOICE mode
TD-SCDMA
-Uplink timing advance control (10.3.6.96)
- CHOICE Timing Advance
Enabled
- CHOICE TDD option
1.28 Mcps TDD
- Uplink synchronization parameters
- Uplink synchronization step size
1
- Uplink synchronization frequency
1
- Synchronization parameters
- SYNC_UL codes bitmap
01010101
- FPACH info
- Timeslot number
0
- Channelisation code
16/15
- Midamble Shift and burst type
- CHOICE TDD option
1.28 Mcps TDD
- Midamble Allocation Mode
Default midamble
- Midamble configuration
16
- WT
4
- PRXUpPCHdes
–80 dBm
- SYNC_UL procedure
- Max SYNC_UL Transmissions
2
- Power Ramp Step
2
- Frequency info
Not present
- UpPCH position info
0
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
TBD dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TD-SCDMA option
1.28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TD-SCDMA option
1.28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TD-SCDMA option
1.28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-CHOICE more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TD-SCDMA
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TD-SCDMA
-TPC Step size
1 dB
-CHOICE mode
TD-SCDMA
-CHOICE mode
TD-SCDMA
-CHOICE TD-SCDMA option
1.28 Mcps
-tstd_indicator
FALSE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TD-SCDMA
-Primary CCPCH info (10.3.6.57)
- CHOICE mode
TD-SCDMA
- CHOICE TD-SCDMA option
1.28 Mcps
TSTD indicator
TRUE
- Cell parameters ID
0
- SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TD-SCDMA
- DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
- Downlink DPCH timeslots and codes (10.3.6.32)
- First individual timeslot info (10.3.6.37)
- Timeslot Number (10.3.6.84)
- CHOICE TD-SCDMA option
1.28 Mcps
- Timeslot number
5
- TFCI existence
True
- Midamble shift and burst type (10.3.6.41)
- CHOICE TD-SCDMA option
1.28 Mcps
- Midamble Allocation Mode
Default
- Midamble configuration
16
- Midamble shift
Not present
- CHOICE TD-SCDMA option
1.28 Mcps
- First timeslot channelisation codes (10.3.6.17)
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
- CHOICE codes representation
Consecutive codes
- First channelisation code
16/1
- Last channelisation code
16/2
- CHOICE more timeslots
No more timeslots
- SCCPCH information for FACH (10.3.6.70)
Not Present
8.3.1A.3.1.5 Test requirements
The inter-frequency hard handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded (see the Note). The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
NOTE: For the target cell and original cell, the SFNs are the same, but the DOFFs are different; therefore, the CFNs are different.
8.3.1A.3.2 Scenario 2
This test case is applicable for UE handovers from primary frequency to the secondary frequency in multi-band network.
8.3.1A.3.2.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.3.2.2 Minimum requirement
The handover delay shall be less than 160ms when the cell is known by the UE and the SFN of the target cell dose not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.3.2.3 Test purpose
The purpose of this test is to verify the requirement for the inter-band handover delay in CELL_DCH state.
8.3.1A.3.2.4 Method of test
8.3.1A.3.2.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
Cell condition: In cell 1, the primary frequency and the secondary frequencies are in band a. In cell 2, the primary frequency uses band a and the secondary frequencies are in band f.
Signal propagation condition: AWGN.
Test instrument: Noise source.
The test parameters are given in table 8.3.1A.3.2.1 and 8.3.1A.3.2.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time"now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C, The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.3.2.1: General test parameters for Handover to inter-band cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-band network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multi-band network, the UE will handover to the secondary frequency in cell 2.
Threshold non-used frequency
dBm
-75
Threshold RSCP for Event 2C
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.3.1A.3.2.2: Cell Specific parameters for Handover to inter-band cell
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
UTRA RF Channel Number(Note 4)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
6
-Inf.
6
-Inf.
6
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-67
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.1A.3.2.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by one.UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
Type 1
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-75 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
Now
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
FALSE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Inter frequency test cases
This message is common for all inter frequency TDD test cases in clause 8.7 and is described in Annex I.
8.3.1A.3.2.5 Test requirements
The inter-band handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded. For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1A.3.3 Scenario 3
This test case is applicable for UE handovers from secondary frequency to secondary frequency in multi-band network.
8.3.1A.3.3.1 Definition and applicability
Handover delay of the UE is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission of the new uplink DPCH or the SYNC-UL in case that a handover with SYNCH uplink exchange is recommended, including the RRC procedure delay as defined in [9].
The requirements and this test apply to the UTRA TDD UE 1,28 Mcps option.
8.3.1A.3.3.2 Minimum requirement
The handover delay shall be less than 160ms when the cell is known by the UE and the SFN of the target cell dose not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.2.
8.3.1A.3.3.3 Test purpose
The purpose of this test is to verify the requirement for the inter-band handover delay in CELL_DCH state.
8.3.1A.3.3.4 Method of test
8.3.1A.3.3.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
Cell condition: In cell 1, the primary frequency uses band a and the secondary frequencies are in band f. In cell 2, the primary frequency and the secondary frequencies are in band a.
Signal propagation condition: AWGN.
Test instrument: Noise source.
The test parameters are given in table 8.3.1A.3.3.1 and 8.3.1A.3.3.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time"now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C, The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.3.1A.3.3.1: General test parameters for Handover to inter-band cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-band network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multi-band network, the UE will handover to the secondary frequency in cell 2.
Threshold non-used frequency
dBm
-75
Threshold RSCP for Event 2C
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.3.1A.3.3.2: Cell Specific parameters for Handover to inter-band cell
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
UTRA RF Channel Number(Note 4)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
6
-Inf.
6
-Inf.
6
dBm/1,28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-67
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.1A.3.3.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) If the UE transmits the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3 then the number of successful tests is increased by one.UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
Type 1
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-75 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
Now
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
FALSE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Inter frequency test cases
This message is common for all inter frequency TDD test cases in clause 8.7 and is described in Annex I.
8.3.1A.3.3.5 Test requirements
The inter-band handover delay shall be less than 160 ms when the cell is known by the UE and the SFN of the target cell does not need to be decoded. For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1B TDD/TDD Handover for 7,68 Mcps Option
8.3.1B.1 Handover to intra-frequency cell
8.3.1B.1.1 Definition and applicability
Handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCH.
The requirements and this test apply to the UTRA TDD UE 7,68 Mcps option.
8.3.1B.1.2 Minimum requirement
The interruption time shall be less than 40 ms in the single carrier case when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/TDD intra-frequency handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+TUL+30*FSFN+20*KC+180*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell and the time that can elapse until the appearance of a Beacon channel
TUL Equal to 10 ms, the time that can elapse until the appearance of the UL timeslot in the target cell
FSFN Equal to 1 if SFN decoding is required and equal to 0 otherwise
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
An intra-frequency TDD target cell shall be considered as known by the UE, if either or both of the following conditions are true:
- the target cell has been measured during the last 5 seconds
- the UE has had a radio link connected to the target cell during the last 5 seconds.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.3.
8.3.1B.1.3 Test purpose
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the single carrier case.
8.3.1B.1.4 Method of test
8.3.1B.1.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1B.1.1 and 8.3.1B.1.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table 8.3.1B.1.1: General test parameters for Handover to intra-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2 and A.2.1
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
T1
s
10
T2
s
10
T3
s
10
Table 8.3.1B.1.2: Cell specific test parameters for Handover to intra-frequency cell
Parameter
Unit
Cell 1
Cell 2
DL timeslot number
0
4
0
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
-9
n.a.
SCH_toffset
dB
0
n.a.
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
n.a.
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
n.a.
-3,12
n.a.
Note 2
dB
1
-Inf.
3
-Inf.
3
PCCPCH RSCP
dBm
-72
n.a.
-Inf.
-70
n.a.
dBm/7,68 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.1B.1.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCH to cell 2 less than 40 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 10 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-Delay restriction flag
Not present
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-New DSCH-RNTI
Not Present
-New H-RNTI
Not Present
-CHOICE mode
TDD
-New E-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-UL Target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
7,68 Mcps TDD
-Indivdual Timeslot interference info
1
-Individual timeslot interference (10.3.6.38)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps TDD
-Timeslot number
12
-UL Timeslot Interference
-90 dBm
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
- TFCS ID
1
-UL Target SIR
20 dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-CHOICE TDD option
7,68 Mcps TDD
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps
-Timeslot number
12
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
7,68 Mcps
-Choice Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
7,68 Mcps
-First timeslot code list
1
-Channelisation code
16/1
-Choice more timeslots
No more timeslots
-E-DCH info
Not Present
Downlink radio resources
-Downlnk HS-PDSCH information
Not Present
-Downlink information common for all radio links (10.3.6.24)
- Choice DPCH info
Downlink DPCH info common for all RL
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-MAC-d HFN initial value
Not present
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps
-TX Diversity mode (10.3.6.86)
None
-Default DPCH Offset Value (10.3.6.16)
0
-MAC-hs reset indicator
Not present
-Post-verification period
Not present
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps
-CHOICE sync case
Case 2
-Timeslot
0
-Cell parameters ID
20
-SCTD indicator
False
-CHOICE DPCH info
Downlink DPCH info for each RL
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
7.68 Mcps TDD
-DL CCTrCH list
1
-TFCS ID
1
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes VHCR (10.3.6.32a)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
7,68 Mcps
-CHOICE Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
7,68 Mcps
-First timeslot channelisation codes VHCR (10.3.6.17a)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/1
-CHOICE more timeslots
No more timeslots
-UL CCTrCH TPC List
Not Present
- DL CCTrCH List to Remove
Not Present
- E-AGCH Info
Not Present
- CHOICE mode
TDD
- E=HICH information
Not Present
-MBMS PL Service Restriction Information
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Checked that this IE is present
-CHOICE mode
TDD
-Cell parameters ID
20
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7.68Mcps TDD
-CHOICE SyncCase
Not Present
-Cell parameters ID
40
- SCTD indicator
FALSE
8.3.1B.1.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.1B.2 Handover to inter-frequency cell
8.3.1B.2.1 Definition and applicability
The handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCH.
The requirements and this test apply to the UTRA TDD UE.
8.3.1B.2.2 Minimum requirement
The interruption time shall be less than 40 ms in the dual carrier case when the cell is known by the UE and the SFN of the target cell needs to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/TDD inter-frequency handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+TUL+30*FSFN+20*KC+180*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell and the time that can elapse until the appearance of a Beacon channel
TUL Equal to 10 ms, the time that can elapse until the appearance of the UL timeslot in the target cell
FSFN Equal to 1 if SFN decoding is required and equal to 0 otherwise
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/TDD handover and equal to 0 otherwise
An inter-frequency TDD target cell shall be considered as known by the UE, if either or both of the following conditions are true:
- the target cell has been measured during the last 5 seconds
- the UE has had a radio link connected to the target cell during the last 5 seconds.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.1.2 and A.5.1.3.
8.3.1B.2.3 Test purpose
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state in the dual carrier case.
8.3.1B.2.4 Method of test
8.3.1B.2.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.1B.2.1 and 8.3.1B.2.2. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at beginning of T3 with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table 8.3.1B.2.1: General test parameters for Handover to inter-frequency cell
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2 and A.2.1
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 2
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Hysteresis parameter for event 2C
Time to Trigger
ms
0
Threshold non-used frequency
dBm
-80
Applicable for Event 2C
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
TSI
s
1.28
The value shall be used for all cells in the test.
T1
s
10
T2
s
10
T3
s
10
Table 8.3.1B.2.2: Cell Specific parameters for Handover to inter-frequency cell
Parameter
Unit
Cell 1
Cell 2
DL timeslot number
0
4
2
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
-9
n.a.
SCH_toffset
dB
0
n.a.
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
n.a.
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
n.a.
-3,12
n.a.
Note 2
dB
1
-Inf.
7
-Inf.
7
PCCPCH RSCP
dBm
-72
n.a.
-Inf.
-66
n.a.
dBm/ 7,68 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.1B.2.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2C.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCH to cell 2 less than 40 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 10 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved..
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
MEASUREMENT CONTROL message, event 2C (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No Report
-Cell synchronisation information reporting indicator
TRUE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2C
-Threshold used frequency
Not Present
-W used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-80 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-Delay restriction flag
Not present
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-New DSCH-RNTI
Not Present
-New H-RNTI
Not Present
-CHOICE mode
TDD
-New E-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-UL Target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
7,68 Mcps TDD
-Indivdual Timeslot interference info
1
-Individual timeslot interference (10.3.6.38)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps TDD
-Timeslot number
12
-UL Timeslot Interference
-90 dBm
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
- TFCS ID
1
-UL Target SIR
20 dB
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-CHOICE TDD option
7,68 Mcps TDD
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps
-Timeslot number
12
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
7,68 Mcps
-Choice Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
7,68 Mcps
-First timeslot code list
1
-Channelisation code
16/1
-Choice more timeslots
No more timeslots
-E-DCH info
Not Present
Downlink radio resources
-Downlnk HS-PDSCH information
Not Present
-Downlink information common for all radio links (10.3.6.24)
- Choice DPCH info
Downlink DPCH info common for all RL
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-MAC-d HFN initial value
Not present
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps
-TX Diversity mode (10.3.6.86)
None
-Default DPCH Offset Value (10.3.6.16)
0
-MAC-hs reset indicator
Not present
-Post-verification period
Not present
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps
-CHOICE sync case
Case 2
-Timeslot
0
-Cell parameters ID
20
-SCTD indicator
False
-CHOICE DPCH info
Downlink DPCH info for each RL
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
7.68 Mcps TDD
-DL CCTrCH list
1
-TFCS ID
1
-Time Info (10.3.6.83)
-Activation Time
T3
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes VHCR (10.3.6.32a)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
7,68 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
7,68 Mcps
-CHOICE Burst Type
Type 1
-Midamble Allocation Mode
Default
-Midamble configuration burst type 1 and 3
16
-Midamble shift
Not present
-CHOICE TDD option
7,68 Mcps
-First timeslot channelisation codes VHCR (10.3.6.17a)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/1
-CHOICE more timeslots
No more timeslots
-UL CCTrCH TPC List
Not Present
- DL CCTrCH List to Remove
Not Present
- E-AGCH Info
Not Present
- CHOICE mode
TDD
- E=HICH information
Not Present
-MBMS PL Service Restriction Information
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2 in Table 8.6.2.4.1.2
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Checked that this IE is present
-CHOICE mode
TDD
-Cell parameters ID
Set to cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2C
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2 in Table 8.6.2.4.1.2
-CHOICE mode
TDD
-Primary CCPCH Info
-CHOICE mode
TDD
-CHOICE TDD Option
7,68 Mcps TDD
-CHOICE Sync Case
Not Present
-Cell Parameters ID
Set to cell parameters ID of Cell 2
-SCTD Indicator
FALSE
8.3.1B.2.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2 TDD/FDD Handover for 3,84 Mcps Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.1 Definition and applicability | The handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCCH.
The requirements and this test apply to the UTRA TDD / FDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.2 Minimum requirement | The interruption time shall be less than 100 ms in the single carrier case when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/FDD handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+40+50*KC+150*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell.
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
An inter-frequency FDD target cell shall be considered known by the UE, if the target cell has been measured by the UE during the last 5 seconds.
The phase reference is the Primary CPICH.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.2 and A.5.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.3 Test purpose | The purpose of this test is to verify the requirement for the TDD/FDD handover delay in CELL_DCH state. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.2.1, 8.3.2.2 and 8.3.2.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G and 2B shall be used. The CPICH_RSCP of the best cell on the unused frequency shall be reported together with Event 2B reporting. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
Table 8.3.2.1: General test parameters for TDD/FDD handover
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 clause A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
TDD cell
Neighbour cell
Cell 2
FDD cell
Final condition
Active cell
Cell 2
FDD cell
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
3
Hysteresis parameter for event 2B
Time to Trigger
ms
0
Absolute threshold used frequency
dBm
-71
Applicable for Event 2B
Threshold non-used frequency
dBm
-80
Applicable for Event 2B
W non-used frequency
1
Applicable for Event 2B
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 FDD neighbours on Channel 2
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
5
T2
s
15
T3
s
5
Table 8.3.2.2: Cell 1 specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 1
DL timeslot number
0
2
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
0
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
dB
5
-1
5
-1
PCCPCH RSCP
dBm
-68
-74
n.a.
dBm/3,84 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior.
Table 8.3.2.3: Cell 2 specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 2
T1, T2
T3
CPICH_Ec/Ior
dB
-10
-12
-12
-15
PCCPCH_Ec/Ior
dB
SCH_Ec/Ior
dB
PICH_Ec/Ior
dB
DPCH_Ec/Ior
dB
n.a.
Note 1
OCNS_Ec/Ior
dB
-0,941
Note 2
CPICH_RSCP
dBm
-83
-77
dB
-3
3
dBm/3,84 MHz
‑70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2 : The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
[Editor's note: subclause 7.3.4 in TS 34.108 (Message sequence chart for Handover Test procedure) is not yet specified]
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2B.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 15 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCCH to cell 2 less than 100 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 [TBD] times.
Specific Message Contents
All messages indicated belowabove shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
MEASUREMENT CONTROL message, event 2B (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
FDD
-Measurement quantity for frequency quality estimate
CPICH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No Report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
FDD
-CPICH Ec/N0 reporting indicator
FALSE
-CPICH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2B
-Threshold used frequency
-71 dBm
-W used frequency
1
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-80 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
FDD
-UARFCN uplink(Nu)
Same uplink UARFCN as used for cell 2
-UARFCN downlink(Nd)
Same downlink UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
FDD
-DPCCH power offset
-6dB
- PC Preamble
1 frame
- SRB delay
7 frames
- Power Control Algorithm
Algorithm1
- TPC step size
1dB
-CHOICE mode
FDD
-Scrambling code type
Long
-Scrambling code number
0 (0 to 16777215)
-Number of DPDCH
Not Present(1)
-Spreading factor
SF is reference to TS34.108 clause 6.10 Parameter Set
-TFCI existence
TRUE
-Number of FBI bit
Not Present(0)
-Puncturing Limit
Reference to TS34.108 clause 6.10 Parameter Set
Downlink radio resources
-CHOICE mode
FDD
-Downlink PDSCH information
Not Present
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-DPC mode
0 (single)
-CHOICE mode
FDD
-Power offset PPilot-DPDCH
TBD
-DL rate matching restriction information
Not Present
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Fixed or Flexible Position
Flexible
-TFCI existence
TRUE
-CHOICE SF
Not Present
-Number of bits for Pilot bits(SF=128,256)
Not Present
-CHOICE mode
FDD
-DPCH compressed mode info (10.3.6.33)
Not Present (Note 1)
-TX Diversity mode (10.3.6.86)
None
-SSDT information (10.3.6.77)
Not Present
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
FDD
-Primary CPICH info (10.3.6.60)
-Primary scrambling code
350
-PDSCH with SHO DCH info (10.3.6.47)
Not Present
-PDSCH code mapping (10.3.6.43)
Not Present
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
FDD
-Primary CPICH usage for channel estimation
Primary CPICH may be used
-DPCH frame offset
0 chips
-Secondary CPICH info
Not Present
-DL channelisation code
-Secondary scrambling code
1
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Code number
SF-1(SF is reference to TS34.108 clause 6.10 Parameter Set)
-Scrambling code change
No change
-TPC combination index
0
- SSDT Cell Identity
-a
- Closed loop timing adjustment mode
Not Present
- SCCPCH information for FACH (10.3.6.70)
Not Present
Note 1: IE "DPCH compressed mode info" is not needed as default values are applied that have previously been received in RADIO BEARER SETUP or RRC CONNECTION SETUP
MEASUREMENT REPORT message for Inter frequency test cases
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
FDD
-Primary CPICH Info
-Primary scrambling code
Set to Primary scrambling code of Cell2
-CPICH Ec/No
Not Present
-CPICH RSCP
Checked that this IE is present
-Pathloss
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2B
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-CHOICE mode
FDD
-Primary CPICH info
-Primary Scrambling Code
Set to Primary scrambling code of Cell2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.2.5 Test requirements | For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]%of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.2A TDD/FDD Handover for 1,28 Mcps Option
8.3.2A.1 Definition and applicability
The handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCCH.
The requirements and this test apply to the UTRA 1,28Mcps TDD / FDD UE.
8.3.2A.2 Minimum requirement
The interruption time shall be less than 100 ms in the single carrier case when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/FDD handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+40+50*KC+150*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell.
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
An inter-frequency FDD target cell shall be considered known by the UE, if the target cell has been measured by the UE during the last 5 seconds.
The phase reference is the Primary CPICH.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.2.2 and A.5.2.2
8.3.2A.3 Test purpose
The purpose of this test is to verify the requirement for the TDD/FDD handover delay in CELL_DCH state.
8.3.2A.4 Method of test
8.3.2A.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.2.1, 8.3.2.2 and 8.3.2.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G and 2B shall be used. The CPICH_RSCP of the best cell on the unused frequency shall be reported together with Event 2B reporting. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
Table 8.3.2A.1: General test parameters for 1,28 Mcps TDD/FDD handover
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channels 12.2 kbps
As specified in TS 25.102 annex A and TS 25.101 annex A
Power Control
On
Initial conditions
Active cell
Cell 1
TDD cell
Neighbour cell
Cell 2
FDD cell
Final condition
Active cell
Cell 2
FDD cell
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
3
Hysteresis parameter for event 2B
Time to Trigger
ms
0
Absolute threshold used frequency
dBm
-71
Applicable for Event 2B
Threshold non-used frequency
dBm
-80
Applicable for Event 2B
W non-used frequency
1
Applicable for Event 2B
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 FDD neighbours on Channel 2
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
5
T2
s
15
T3
s
5
Table 8.3.2A.2: Cell 1 (1,28 Mcps TDD cell) specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 1
Timeslot number
0
5
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
OCNS_Ec/Ior
dB
-3
Note 2
n.a.
dB
5
-1
5
-1
PCCPCH RSCP
dBm
-68
-74
n.a.
dBm/ 1,28 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Table 8.3.2A.3: Cell 2 (FDD cell) specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 2
T1
T2
T3
CPICH_Ec/Ior
dB
-10
PCCPCH_Ec/Ior
dB
-12
SCH_Ec/Ior
dB
-12
PICH_Ec/Ior
dB
-15
DPCH_Ec/Ior
dB
n.a.
Note 1
OCNS_Ec/Ior
dB
-0.941
Note 2
CPICH_RSCP
dBm
-Inf
-75
dB
-Inf
5
dBm/ 3,84 MHz
‑70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2 : The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.2A.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure to be specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2B.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 15 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCCH to cell 2 less than 100 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved..
Specific Message Contents
All messages indicated belowabove shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
MEASUREMENT CONTROL message, event 2B (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
FDD
-Measurement quantity for frequency quality estimate
CPICH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No Report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
FDD
-CPICH Ec/N0 reporting indicator
FALSE
-CPICH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2B
-Threshold used frequency
-71 dBm
-W used frequency
1
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-80 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
FDD
-UARFCN uplink(Nu)
Same uplink UARFCN as used for cell 2
-UARFCN downlink(Nd)
Same downlink UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
FDD
-DPCCH power offset
-6dB
- PC Preamble
1 frame
- SRB delay
7 frames
- Power Control Algorithm
Algorithm1
- TPC step size
1dB
-CHOICE mode
FDD
-Scrambling code type
Long
-Scrambling code number
0 (0 to 16777215)
-Number of DPDCH
Not Present(1)
-Spreading factor
SF is reference to TS34.108 clause 6.10 Parameter Set
-TFCI existence
TRUE
-Number of FBI bit
Not Present(0)
-Puncturing Limit
Reference to TS34.108 clause 6.10 Parameter Set
Downlink radio resources
-CHOICE mode
FDD
-Downlink PDSCH information
Not Present
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-DPC mode
0 (single)
-CHOICE mode
FDD
-Power offset PPilot-DPDCH
TBD
-DL rate matching restriction information
Not Present
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Fixed or Flexible Position
Flexible
-TFCI existence
TRUE
-CHOICE SF
Not Present
-Number of bits for Pilot bits(SF=128,256)
Not Present
-CHOICE mode
FDD
-DPCH compressed mode info (10.3.6.33)
Not Present (Note 1)
-TX Diversity mode (10.3.6.86)
None
-SSDT information (10.3.6.77)
Not Present
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
FDD
-Primary CPICH info (10.3.6.60)
-Primary scrambling code
350
-PDSCH with SHO DCH info (10.3.6.47)
Not Present
-PDSCH code mapping (10.3.6.43)
Not Present
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
FDD
-Primary CPICH usage for channel estimation
Primary CPICH may be used
-DPCH frame offset
0 chips
-Secondary CPICH info
Not Present
-DL channelisation code
-Secondary scrambling code
1
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Code number
SF-1(SF is reference to TS34.108 clause 6.10 Parameter Set)
-Scrambling code change
No change
-TPC combination index
0
- SSDT Cell Identity
-a
- Closed loop timing adjustment mode
Not Present
- SCCPCH information for FACH (10.3.6.70)
Not Present
Note 1: IE "DPCH compressed mode info" is not needed as default values are applied that have previously been received in RADIO BEARER SETUP or RRC CONNECTION SETUP
MEASUREMENT REPORT message for Inter frequency test cases
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
FDD
-Primary CPICH Info
-Primary scrambling code
Set to Primary scrambling code of Cell2
-CPICH Ec/No
Not Present
-CPICH RSCP
Checked that this IE is present
-Pathloss
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2B
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-CHOICE mode
FDD
-Primary CPICH info
-Primary Scrambling Code
Set to Primary scrambling code of Cell2
8.3.2A.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95%of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.2B TDD/FDD Handover for 7,68 Mcps Option
8.3.2B.1 Definition and applicability
The handover interruption time is defined as the time between the end of the last TTI containing a transport block on the old DPCH and the time the UE starts transmission of the new uplink DPCCH.
The requirements and this test apply to the UTRA TDD / FDD UE.
8.3.2B.2 Minimum requirement
The interruption time shall be less than 100 ms in the single carrier case when the cell is known by the UE and the SFN of the target cell does not need to be decoded. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The interruption time is dependent on whether the target cell is known for the UE or not.
If TDD/FDD handover is commanded, the interruption time shall be less than,
Tinterrupt= Toffset+40+50*KC+150*UC ms
where,
Toffset Equal to 10 ms, the frame timing uncertainty between the old cell and the target cell.
KC Equal to 1 if a known target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
UC Equal to 1 if an unknown target cell is indicated in the RRC message implying TDD/FDD handover and equal to 0 otherwise
An inter-frequency FDD target cell shall be considered known by the UE, if the target cell has been measured by the UE during the last 5 seconds.
The phase reference is the Primary CPICH.
The interruption time requirements for an unknown target cell shall apply only if the signal quality of the unknown target cell is sufficient for successful synchronisation with one attempt.
The normative reference for this requirement is TS 25.123 [2] clauses 5.2 and A.5.3.
8.3.2B.3 Test purpose
The purpose of this test is to verify the requirement for the TDD/FDD handover delay in CELL_DCH state.
8.3.2B.4 Method of test
8.3.2B.4.1 Initial conditions
Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in table 8.3.2B.1, 8.3.2B.2 and 8.3.2B.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G and 2B shall be used. The CPICH_RSCP of the best cell on the unused frequency shall be reported together with Event 2B reporting. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [16].
Table 8.3.2B.1: General test parameters for TDD/FDD handover
Parameter
Unit
Value
Comment
DCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 annex A.2.2 and TS 25.101 annex A
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
TDD cell
Neighbour cell
Cell 2
FDD cell
Final condition
Active cell
Cell 2
FDD cell
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
3
Hysteresis parameter for event 2B
Time to Trigger
ms
0
Absolute threshold used frequency
dBm
-71
Applicable for Event 2B
Threshold non-used frequency
dBm
-80
Applicable for Event 2B
W non-used frequency
1
Applicable for Event 2B
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 FDD neighbours on Channel 2
TSI
s
1.28
The value shall be used for all cells in the test.
T1
s
5
T2
s
15
T3
s
5
Table 8.3.2B.2: Cell 1 specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 1
DL timeslot number
0
2
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
0
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
dB
5
-1
5
-1
PCCPCH RSCP
dBm
-68
-74
n.a.
dBm/7,68 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior
Table 8.3.2B.3: Cell 2 specific test parameters for TDD/FDD handover
Parameter
Unit
Cell 2
T1, T2
T3
CPICH_Ec/Ior
dB
-10
PCCPCH_Ec/Ior
dB
-12
SCH_Ec/Ior
dB
-12
PICH_Ec/Ior
dB
-15
DPCH_Ec/Ior
dB
n.a.
Note 1
OCNS_Ec/Ior
dB
-0.941
Note 2
CPICH_RSCP
dBm
-83
-77
dB
-3
3
dBm/7.68 MHz
‑70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2 : The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
8.3.2B.4.2 Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
[Editor's note: subclause 7.3.4 in TS 34.108 (Message sequence chart for Handover Test procedure) is not yet specified]
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2B.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time at T3.
8) After 15 seconds, the SS shall switch the power settings from T2 to T3
9) UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2. If the UE transmits the UL DPCCH to cell 2 less than 100 ms from the beginning of time period T3 then the number of successful tests is increased by one.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved..
Specific Message Contents
All messages indicated belowabove shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
MEASUREMENT CONTROL message, event 2B (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting criteria
Inter-frequency reporting criteria
-Inter-frequency reporting criteria
-Filter coefficient
0
-CHOICE mode
FDD
-Measurement quantity for frequency quality estimate
CPICH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA Carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No Report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
FDD
-CPICH Ec/N0 reporting indicator
FALSE
-CPICH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Measurement validity (10.3.7.51)
Not Present
-Inter-frequency set update (10.3.7.22)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Inter-frequency event identity (10.3.7.14)
Event 2B
-Threshold used frequency
-71 dBm
-W used frequency
1
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within monitored set on non-used frequency
-Maximum number of reported cells per reported non-used frequency
1
-Parameters required for each non-used frequency
1
-Threshold non-used frequency
-80 dBm
-W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
FDD
-UARFCN uplink(Nu)
Same uplink UARFCN as used for cell 2
-UARFCN downlink(Nd)
Same downlink UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
33 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
FDD
-DPCCH power offset
-6dB
- PC Preamble
1 frame
- SRB delay
7 frames
- Power Control Algorithm
Algorithm1
- TPC step size
1dB
-CHOICE mode
FDD
-Scrambling code type
Long
-Scrambling code number
0 (0 to 16777215)
-Number of DPDCH
Not Present(1)
-Spreading factor
SF is reference to TS34.108 clause 6.10 Parameter Set
-TFCI existence
TRUE
-Number of FBI bit
Not Present(0)
-Puncturing Limit
Reference to TS34.108 clause 6.10 Parameter Set
Downlink radio resources
-CHOICE mode
FDD
-Downlink PDSCH information
Not Present
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-DPC mode
0 (single)
-CHOICE mode
FDD
-Power offset PPilot-DPDCH
TBD
-DL rate matching restriction information
Not Present
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Fixed or Flexible Position
Flexible
-TFCI existence
TRUE
-CHOICE SF
Not Present
-Number of bits for Pilot bits(SF=128,256)
Not Present
-CHOICE mode
FDD
-DPCH compressed mode info (10.3.6.33)
Not Present (Note 1)
-TX Diversity mode (10.3.6.86)
None
-SSDT information (10.3.6.77)
Not Present
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
FDD
-Primary CPICH info (10.3.6.60)
-Primary scrambling code
350
-PDSCH with SHO DCH info (10.3.6.47)
Not Present
-PDSCH code mapping (10.3.6.43)
Not Present
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
FDD
-Primary CPICH usage for channel estimation
Primary CPICH may be used
-DPCH frame offset
0 chips
-Secondary CPICH info
Not Present
-DL channelisation code
-Secondary scrambling code
1
-Spreading factor
Reference to TS34.108 clause 6.10 Parameter Set
-Code number
SF-1(SF is reference to TS34.108 clause 6.10 Parameter Set)
-Scrambling code change
No change
-TPC combination index
0
- SSDT Cell Identity
-a
- Closed loop timing adjustment mode
Not Present
- SCCPCH information for FACH (10.3.6.70)
Not Present
Note 1: IE "DPCH compressed mode info" is not needed as default values are applied that have previously been received in RADIO BEARER SETUP or RRC CONNECTION SETUP
MEASUREMENT REPORT message for Inter frequency test cases
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Checked that this IE is present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
FDD
-Primary CPICH Info
-Primary scrambling code
Set to Primary scrambling code of Cell2
-CPICH Ec/No
Not Present
-CPICH RSCP
Checked that this IE is present
-Pathloss
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2B
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
FDD
-UARFCN uplink (Nu)
Not Present
-UARFCN downlink (Nd)
Same frequency as channel 2 in Table 8.3.2.3
-CHOICE mode
FDD
-Primary CPICH info
-Primary Scrambling Code
Set to Primary scrambling code of Cell2
8.3.2B.5 Test requirements
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95%of the cases.
Note: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3 TDD/GSM Handover | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.1.1 3,84 Mcps option | The UTRAN to GSM cell handover interruption time is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission on the channel of the new RAT.
The requirements and this test apply to the combined TDD (3,84 Mcps option) and GSM UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.1.2 1,28 Mcps option | The UTRAN to GSM cell handover delay is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission on the channel of the new RAT.
The requirements and this test apply to the combined TDD (1,28 Mcps option) and GSM UE |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.1.3 7,68 Mcps option | The UTRAN to GSM cell handover delay is defined as the time from the end of the last TTI containing an RRC message implying hard handover to the transmission on the channel of the new RAT.
The requirements and this test apply to the combined TDD (7,68 Mcps option) and GSM UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.2.1 3,84 Mcps option | The interruption time shall be less than 40 ms in the case where the UE has synchronised to the GSM cell before the HANDOVER FROM UTRAN COMMAND is received. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of [FFS]%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.3.2 and A.5.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.2.2 1,28 Mcps option | The handover delay shall be less than 90 ms in the case where the UE has synchronised to the GSM cell before the HANDOVER FROM UTRAN COMMAND is received. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.3.2 and A.5.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.2.3 7,68 Mcps option | The handover delay shall be less than 90 ms in the case where the UE has synchronised to the GSM cell before the HANDOVER FROM UTRAN COMMAND is received. The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.3.2 and A.5.3. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.3 Test purpose | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.3.1 3,84 Mcps option | To verify that the UE meets the minimum requirement. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.3.2 1,28 Mcps option | To verify that the UE meets the minimum requirement. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4.1 3,84 Mcps option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4.1.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4 for TDD conditions, and clause A1.2 of TS 51.010-1 [23] for the corresponding GSM conditions.
The test parameters are given in Table 8.3.3.1, 8.3.3.2 and 8.3.3.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 3C shall be used. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a HANDOVER FROM UTRAN COMMAND message with activation time at beginning of T3 with one active cell, cell 2. The HANDOVER FROM UTRAN COMMAND message shall be sent to the UE such that the delay between the last the end of the last received TTI containing the message and the beginning of T3 is at least equal to the RRC procedure delay as defined in [9]. In the GSM Handover command contained in this message, IE starting time shall not be included.
Cell 1 is a UTRA TDD cell and cell 2 is a GSM cell. The Beacon timeslot shall be transmitted in timeslot 0 for cell 1 and no second Beacon timeslot shall be provided for cell 1. The DL DPCH shall be transmitted in timeslot 1 and the UL DPCH shall be transmitted in timeslot 3.
Table 8.3.3.1: General test parameters for TDD/GSM handover
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
UTRA TDD cell
Neighbour cell
Cell 2
GSM cell
Final condition
Active cell
Cell 2
GSM cell
Inter-RAT measurement quantity
GSM carrier RSSI
BSIC verification required
Required
Threshold other system
dBm
-80
Absolute GSM carrier RSSI threshold for Event 3C.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
12 TDD neighbours on Channel 1
6 GSM neighbours including ARFCN 1
Measurement control information is sent before the start of time period T1.
Tidentify abort
s
5
Treconfirm abort
s
5
T1
s
10
T2
s
10
T3
s
10
Table 8.3.3.2: Cell Specific Parameters for Handover UTRAN to GSM cell case (cell 1)
Parameter
Unit
Cell 1
DL timeslot number
0
1
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
0
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
n.a.
OCNS_Ec/Ior
dB
-3,12
Note 2
n.a.
dB
6
6
PCCPCH RSCP
dBm
-68
n.a.
dBm/3,84 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Table 8.3.3.3: Cell Specific Parameters for Handover UTRAN to GSM cell case (cell 2)
Parameter
Unit
Cell 2
T1
T2, T3
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-85
-75 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4.1.2 Procedure | 1) The RF parameters for cell 1 are set up according to T1.
2) The UE is switched on
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4
4) The RF parameters for cell 2 are set up according to T1 and the SS configures a traffic channel
5) SS shall transmit a MEASUREMENT CONTROL message to cell 1
6) After 10 seconds, the SS shall switch the power settings from T1 to T2
7) UE shall transmit a MEASUREMENT REPORT message triggered by event 3C
8) SS shall transmit a HANDOVER FROM UTRAN COMMAND message with activation time at T3 and indicating the traffic channel of the target GSM cell to the UE through DCCH of the serving UTRAN cell.
9) After 10 seconds, the SS shall switch the power settings from T2 to T3
10) UE shall transmit a burst on the traffic channel of cell 2 implying that it has switched to the GSM cell. The UE sends a HANDOVER ACCESS message. If the UE transmits access bursts on the new DCCH of the target cell less than 40 ms from the beginning of time period T3, then the number of successful tests is increased by one.
[Editor's note: TS 34.108, 7.3.4 shall specify the messages HANDOVER ACCESS, PHYSICAL INFORMATION, SABM, UA and HANDOVER COMPLETE]
11) After 10 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
12) Repeat step 1-11 [TBD] times
Specific Message Contents
All messages indicated below above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
Note: Numbers in brackets after an item e.g “Message Type (10.2.17)” in the IE description are references to clause numbers in TS 25.331 [9] describing that item in more detail.
MEASUREMENT CONTROL message (step 5):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
4
-Measurement Command (10.3.7.46)
Setup
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-RAT measurement
-Inter-RAT measurement (10.3.7.27)
-Inter-RAT measurement objects list (10.3.7.23)
Not Present
-Inter-RAT measurement quantity (10.3.7.29)
-Measurement quantity for UTRAN quality estimate (10.3.7.38)
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH RSCP
-CHOICE system
GSM
-Measurement quantity
GSM Carrier RSSI
-Filter coefficient
0
-BSIC verification required
Required
-Inter-RAT reporting quantity (10.3.7.32)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within active set or within virtual active set or of the other RAT
-Maximum number of reported cells
2
-CHOICE report criteria
Inter-RAT measurement reporting criteria
-Inter-RAT measurement reporting criteria (10.3.7.30)
-Parameters required for each event
1
-Inter-RAT event identity (10.3.7.24)
Event 3C
-Threshold own system
Not Present
-W
Not Present
-Threshold other system
-80 dBm
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
HANDOVER FROM UTRAN COMMAND message (step 8):
Information Element
Value/remark
Message Type
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Activation time
At T3
RB information elements
-RAB information list
1
-RAB Info
Not present
Other information elements
-CHOICE System type
GSM
-Frequency Band
GSM/DCS 1800 Band
-GSM message
-Single GSM message
[TBD]
-GSM message List
GSM HANDOVER COMMAND formatted as BIT STRING(1..512). The contents of the HANDOVER COMMAND see next table.
HANDOVER COMMAND
Same as the HANDOVER COMMAND for M = 2 in clause 26.6.5.1 of TS 51.010, except that the CHANNEL MODE IE is included with value = speech full rate or half rate version 3
MEASUREMENT REPORT message (step 7)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-RAT Measured results list
-Inter-RAT-frequency measured results (10.3.7.26)
1
-CHOICE System
GSM
-Measured GSM cells
1
-GSM Carrier RSSI
Checked that this IE is present
-CHOICE BSIC
Verified BSIC
-inter-RAT cell id
Checked that this IE is present
-Observed Time difference to GSM cell
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-RAT measurement event results
-Inter-RAT event identity
3C
-Cells to report
1
-CHOICE BSIC
Verified BSIC
-inter-RAT cell id
Checked that this IE is present |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4.2 1,28 Mcps option | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4 for TDD conditions, and clause A1.2 of TS 51.010-1 [24] for the corresponding GSM conditions.
The test parameters are given in Table 8.3.4.1, 8.3.4.2 and 8.3.4.3 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 3C shall be used. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a HANDOVER FROM UTRAN COMMAND message with activation time "now" with one active cell, cell 2. The HANDOVER FROM UTRAN COMMAND message shall be sent to the UE during period T2. The starting point of T3 is defined as the end of the last TTI containing the HANDOVER COMMAND. In the GSM Handover command contained in this message, IE starting time shall not be included.
Cell 1 is a UTRA TDD cell and cell 2 is a GSM cell. The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 2.
Table 8.3.3.4.1: General test parameters for 1,28Mcps TDD/GSM handover
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
UTRA TDD cell
Neighbour cell
Cell 2
GSM cell
Final condition
Active cell
Cell 2
GSM cell
Inter-RAT measurement quantity
GSM carrier RSSI
BSIC verification required
Required
Threshold other system
dBm
-80
Absolute GSM carrier RSSI threshold for Event 3C.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
12 TDD neighbours on Channel 1
6 GSM neighbours including ARFCN 1
Measurement control information is sent before the start of time period T1.
Tidentify abort
s
5
As specified in section 8.1A.2.5
Treconfirm abort
s
5
As specified in section 8.1A.2.5
T1
s
10
T2
s
10
T3
s
10
Table 8.3.3.4.2: Cell 1 (1,28Mcps )specific test parameters for TDD/GSM handover
Parameter
Unit
Cell 1
DL timeslot number
0
DwPTS
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
PCCPCH_Ec/Ior
dB
-3
DwPCH_Ec/Ior
dB
0
OCNS_Ec/Ior
dB
-3
dB
5
5
dBm/1.28 MHz
-70
Propagation Condition
AWGN
Table 8.3.3.4.3: Cell 2 (GSM )specific test parameters for TDD/GSM handover
Parameter
Unit
Cell 2
T1
T2, T3
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-85
-75 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.3.4.2.2 Procedure | 1) The RF parameters for cell 1 are set up according to T1.
2) The UE is switched on
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4
4) The RF parameters for cell 2 are set up according to T1 and the SS configures a traffic channel
5) SS shall transmit a MEASUREMENT CONTROL message to cell 1
6) After 10 seconds, the SS shall switch the power settings from T1 to T2
7) UE shall transmit a MEASUREMENT REPORT message triggered by event 3C
8) SS shall transmit a HANDOVER FROM UTRAN COMMAND message with activation time “now” and indicating the traffic channel of the target GSM cell to the UE through DCCH of the serving UTRAN cell. The start of T3 is defined as the end of the last TTI, containing the HANDOVER COMMAND.
10) UE shall transmit a burst on the traffic channel of cell 2 implying that it has switched to the GSM cell. The UE sends a HANDOVER ACCESS message. If the UE transmits access bursts on the new DCCH of the target cell less than 90 ms from the beginning of time period T3, then the number of successful tests is increased by one.
11) At the end of T3 the UE is switched off. Any timing information of cell 2 is deleted in the UE.
12) Repeat step 1-11 until the confidence level according to annex F.6.2A is achieved
Specific Message Contents
All messages shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
Note: 10.x.y.z in the IE description refers to clauses in TS 25.331 [9].
MEASUREMENT CONTROL message (step 5):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
4
-Measurement Command (10.3.7.46)
Setup
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-RAT measurement
-Inter-RAT measurement (10.3.7.27)
-Inter-RAT measurement objects list (10.3.7.23)
Not Present
-Inter-RAT measurement quantity (10.3.7.29)
-Measurement quantity for UTRAN quality estimate (10.3.7.38)
-Filter coefficient
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH RSCP
-CHOICE system
GSM
-Measurement quantity
GSM Carrier RSSI
-Filter coefficient
0
-BSIC verification required
Required
-Inter-RAT reporting quantity (10.3.7.32)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report cells within active set or within virtual active set or of the other RAT
-Maximum number of reported cells
2
-CHOICE report criteria
Inter-RAT measurement reporting criteria
-Inter-RAT measurement reporting criteria (10.3.7.30)
-Parameters required for each event
1
-Inter-RAT event identity (10.3.7.24)
Event 3C
-Threshold own system
Not Present
-W
Not Present
-Threshold other system
-80 dBm
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting cell status (10.3.7.61)
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
HANDOVER FROM UTRAN COMMAND message (step 8):
Information Element
Value/remark
Message Type(10.2.15)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Activation time
now
RB information elements
-RAB information list
1
-RAB Info
Not present
- RAB identity
0000 0001B
The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.
- CN domain identity
CS domain
- NAS Synchronization Indicator
Not present
- Re-establishment timer
Use T315
Other information elements
-CHOICE System type
GSM
-Frequency Band
Set to "GSM/ PCS 1900" if GSM/ PCS 1900 is used in this test. Otherwise set to "GSM/DCS 1800 Band"
-CHOICE GSM message
- Single GSM message
GSM HANDOVER COMMAND formatted and coded according to GSM specifications as BIT STRING (1..512). The first/ leftmost/ most significant bit of the bit string contains bit 8 of the first octet of the GSM message. The contents of the HANDOVER COMMAND see next table.
HANDOVER COMMAND
Information Element (GSM)
Value/remark
Version
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
5
- BCCH Carrier Number
1
Channel Description 2
- Channel Type and TDMA offset
TCH/F + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house, but not Zero.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
1
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command and ACCESS Type
- ATC
0
- EPC_mode
0
REL-5
- FPC
0
R99 and REL-4 only
- EPC_FPC
0
REL-5
- Power level
Chosen arbitrarily by the test house.
Synchronization Indication
Not present.
Channel Mode
speech full rate or half rate version 1
All other information elements
Not present.
MEASUREMENT REPORT message (step 7)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-RAT Measured results list
-Inter-RAT-frequency measured results (10.3.7.26)
1
-CHOICE System
GSM
-Measured GSM cells
1
-GSM Carrier RSSI
Checked that this IE is present
-CHOICE BSIC
Verified BSIC
-inter-RAT cell id
Checked that this IE is present
-Observed Time difference to GSM cell
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-RAT measurement event results
-Inter-RAT event identity
3C
-Cells to report
1
-CHOICE BSIC
Verified BSIC
-inter-RAT cell id
Checked that this IE is present |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.