hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.1.2 Test purpose
|
1. To verify that upon initiation of an outgoing broadcast call with User-to-Dispatcher information by the user, the MS includes a User-to-dispatcher information element in the SETUP message.
2. To verify correct establishment and clearing of the broadcast call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
-
PIXIT Statements:
- Way to activate User-to-Dispatcher Information
- Way to configure VBS.
- Way to initiate VBS calls.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
By means of appropriate MMI function, the user enters a string, which shall be included in the User-to-Dispatcher Information.
Then MS is made to initiate a broadcast call. In the SETUP message, the User-to-dispatcher information element shall be present and shall include the requested string. Then, SS releases immediately the call with a TERMINATION message.
Then MS is made to initiate a second broadcast call with User-to-Dispatcher Information including a long string. In the SETUP message, the User-to-dispatcher information element shall be present with the requested string. Then it is checked that the call can be successfully established and cleared.
Maximum Duration of Test
2 minutes
Expected Sequence
Step
Direction
Message
Comments
0
MS
The MS is in idle mode.
1
MS
MMI actions to initiate a VBS call with User-to-Dispatcher Information including the string 'abcdef9'
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/FS
4
MS -> SS
CM SERVICE REQUEST
L2: SABM / UA
5
SS -> MS
CM SERVICE ACCEPT
6
MS -> SS
SETUP
User-to-dispatcher IE included. See specific message contents.
7
SS -> MS
TERMINATION
8
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link. L2: DISC/UA.
9
MS
MMI actions to initiate a VBS call with User-to-Dispatcher Information with the string 'abcdefghijklmnopqrstuvwxyz012345'
10
MS -> SS
CHANNEL REQUEST
11
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/F, single RF channel
GSM 450: 275
GSM 480: 322
GSM 900: 50,
DCS 1 800: 750
PCS 1 900: 650
GSM710: 470
GSM 750: 470
T-GSM 810: 470
GSM 850: 177
12
MS -> SS
CM SERVICE REQUEST
L2: SABM / UA
13
SS -> MS
CM SERVICE ACCEPT
14
MS -> SS
SETUP
User-to-dispatcher IE included. See specific message contents.
15
SS -> MS
CHANNEL MODE MODIFY
16
MS -> SS
CHANNEL MODE MODIFY ACKNOWLEDGE
17
SS -> MS
CONNECT
18
SS -> MS
TERMINATION
19
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2: DISC/UA.
Specific message contents:
SETUP
As default message contents as defined in subclause 26.14.10 except:
Information Element
Value/remark
User-to-dispatcher
- IEI
'7E'O
- length
1+the entered string length
- PD
User specific protocol
- user-user
The string as entered coded in IA5 characters
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.2 VGCS-VBS / User-to-Dispatcher information / GCC MO call
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.2.1 Conformance requirement
|
The request of the calling subscriber to set up a voice group call may specify information to be sent as user-to-dispatcher information to the network; in this case the user-to-dispatcher information is included in the signalling for call setup from the mobile station to the network. It is the responsibility of the input function to ensure that the user-to-dispatcher information has a correct format (in particular, an allowed length).
The initial signalling from the originating service subscriber informs the network that a voice group call is required and details the group ID; it may specify user-to-dispatcher information.
The User-to-dispatcher information element is included in the SETUP message.
References
3GPP TS 03.68 subclauses 4.2.1.1 and 11.3.1.1.1
3GPP TS 04.68 subclause 8.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.2.2 Test purpose
|
1. To verify that upon initiation of an outgoing group call with User-to-Dispatcher Information by the user, the MS includes a User-to-dispatcher information element in the SETUP message.
2. To verify that the group call can be successfully established and cleared.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
-
PIXIT Statements:
- Way to activate User-to-Dispatcher Information.
- Way to configure VGCS.
- Way to initiate VGCS calls.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
By means of appropriate MMI function, the user enters a string, which shall be included in the User-to-Dispatcher Information.
Then MS is made to initiate a VGCS call. In the SETUP message, the User-to-dispatcher information element shall be present and shall include the requested string. Then, SS releases immediately the call with a TERMINATION message.
Then MS is made to initiate a second VGCS call with User-to-Dispatcher Information including a long string. In the SETUP message, the User-to-dispatcher information element shall be present with the requested string. Then it is checked that the call can be successfully established and cleared.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step
Direction
Message
Comments
0
MS
MMI actions to initiate a VGCS call with User-to-Dispatcher Information with the string 'abcdef9'.
1
MS -> SS
CHANNEL REQUEST
2
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/FS
3
MS -> SS
CM SERVICE REQUEST
L2: SABM / UA
4
SS -> MS
CM SERVICE ACCEPT
5
MS -> SS
SETUP
User-to dispatcher IE included. See specific message contents
6
SS -> MS
TERMINATION
7
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2: DISC/UA.
10
MS
MMI actions to initiate a VGCS call with User-to-Dispatcher Information with the string 'abcdefghijklmnopqrstuvwxyz012345'.
11
MS -> SS
CHANNEL REQUEST
12
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/F, single RF channel
GSM 450: 275
GSM 480: 322
GSM 900: 50
DCS 1 800: 750
PCS 1 900: 650
GSM710: 470
GSM 750: 470
T-GSM 810: 470
GSM 850: 177
13
MS -> SS
CM SERVICE REQUEST
L2: SABM / UA
14
SS -> MS
CM SERVICE ACCEPT
15
MS -> SS
SETUP
User-to-dispatcher IE included
16
SS -> MS
CHANNEL MODE MODIFY
17
MS -> SS
CHANNEL MODE MODIFY ACKNOWLEDGE
18
SS -> MS
CONNECT
19
SS -> MS
TERMINATION
20
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2: DISC/UA.
Specific message contents:
SETUP
As default message contents as defined in subclause 26.14.10 except:
Information Element
Value/remark
User-user
- IEI
'7E'O
- length
1 + the entered string length
- PD
User specific protocol
- user-user
The string as entered coded in IA5 characters
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.3 VGCS-VBS / User-to-Dispatcher information / Compressed user information in VBS fast call set-up
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.3.1 Conformance requirement
|
The request of the calling subscriber to set up a voice group call may specify information to be sent as user-to-dispatcher information to the network; in this case the user-to-dispatcher information is included in the signalling for call setup from the mobile station to the network. It is the responsibility of the input function to ensure that the user-to-dispatcher information has a correct format (in particular, an allowed length).
User-to-dispatcher information can be compressed or uncompressed.
The message IMMEDIATE SETUP 2 is sent by the MS to the network in order to set-up a group call immediately, i.e. without previous establishment of an MM connection, and to include compressed user-to dispatcher information. The message shall be used if the MS has a valid TMSI.
References
3GPP TS 04.69 subclauses 4.2.1.1, 4.2.7, 11.3.1.1.1 and 11.3.1.1.3.
3GPP TS 04.69 subclause 6.2.2 and clause 8.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.3.2 Test purpose
|
To verify that upon initiation of an outgoing VBS fast call with User-to-Dispatcher Information by the user, the MS includes a Compressed User-to-Dispatcher Information information element in the IMMEDIATE SETUP 2 message;
To verify that the VBS fast call can be successfully established and cleared.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
-
PIXIT Statements:
- Way to activate User-to-Dispatcher Information.
- Way to configure VBS.
- Way to initiate VBS fast calls set-up.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
By means of appropriate MMI function, the user enters a string, which shall be included in the User-to-Dispatcher Information. Then MS is made to initiate a VBS fast call. Check that the MS sends an IMMEDIATE SETUP 2 message, and check that the Compressed User-to-Dispatcher Information element is present. Then, it is checked that the call can be successfully established and released.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step
Direction
Message
Comments
0
MS
The MS is in idle mode.
1
MS
MMI actions to initiate a VBS fast call with the User-to-Dispatcher Information "1234567890"
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/F, single RF channel
GSM 450: 275
GSM 480: 322
GSM 900: 50
DCS 1 800: 750
PCS 1 900: 650
GSM710: 470
GSM 750: 470
T-GSM 810: 470
GSM 850: 177
4
MS -> SS
IMMEDIATE SETUP
L2: SABM / UA, BCC message including the Compressed User-to-Dispatcher Information information element shall be present, see Specific message contents
5
SS -> MS
CHANNEL MODE MODIFY
Very early assignment
6
MS -> SS
CHANNEL MODE MODIFY ACK
7
SS -> MS
CONNECT
8
SS -> MS
TERMINATION
9
SS -> MS
CHANNEL RELEASE
Specific message contents:
IMMEDIATE SETUP 2
Information element
Value/remark
Protocol discriminator
'0001'B for BCC
Transaction identifier
'0001'B
Message type
'0x111011'B
Spare half octet
'0000'B
Ciphering key sequence number
PICS/PIXIT
Mobile station classmark
PICS/PIXIT
TMSI
PICS/PIXIT
Group identity
PICS/PIXIT
Compressed utdi
'00075BCD16'O
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.4 VGCS-VBS / User-to-Dispatcher information / Compressed User-to-Dispatcher information in VGCS fast call set-up
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.4.1 Conformance requirement
|
The request of the calling subscriber to set up a voice group call may specify information to be sent as user-to-dispatcher information to the network; in this case the user-to-dispatcher information is included in the signalling for call setup from the mobile station to the network. It is the responsibility of the input function to ensure that the user-to-dispatcher information has a correct format (in particular, an allowed length).
User-to-dispatcher information can be compressed or uncompressed.
The message IMMEDIATE SETUP 2 is sent by the MS to the network in order to set-up a group call immediately, i.e. without previous establishment of an MM connection, and to include compressed user-to dispatcher information. The message shall be used if the MS has a valid TMSI.
References
3GPP TS 03.68 subclauses 4.2.1.1, 4.2.7, 11.3.1.1.1 and 11.3.1.1.3.
3GPP TS 04.68 subclause 6.2.2 and clause 8.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.4.2 Test purpose
|
1. To verify that upon initiation of an outgoing VGCS fast call with Compressed User-to-Dispatcher Information by the user, the MS includes a Compressed User-to-Dispatcher Information information element in the IMMEDIATE SETUP 2 message.
2. To verify that the VGCS fast call can be successfully established and cleared.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.11.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
-
PIXIT Statements:
- Way to activate User-to-Dispatcher Information.
- Way to configure VGCS.
- Way to initiate VGCS fast calls set-up.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
By means of appropriate MMI function, the user enters a string, which shall be included in the User-to-Dispatcher Information. Then MS is made to initiate a VGCS fast call. Check that the MS sends an IMMEDIATE SETUP 2 message, and check that the Compressed User-to-Dispatcher Information information element is present. Then, it is checked that the VGCS fast call can be successfully established and released.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step
Direction
Message
Comments
0
MS
The MS is in idle mode.
1
MS
MMI actions to initiate a VGCS fast call with the User-to-Dispatcher Information "1234567890"
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/F, single RF channel
GSM 450: 275
GSM 480: 322
GSM 900: 50
DCS 1 800: 750
PCS 1 900: 650
GSM710: 470
GSM 750: 470
T-GSM 810: 470
GSM 850: 177
4
MS -> SS
IMMEDIATE SETUP
L2: SABM / UA, GCC message including the Compressed utdi information element shall be present, see Specific message contents
5
SS -> MS
CHANNEL MODE MODIFY
Very early assignment
6
MS -> SS
CHANNEL MODE MODIFY ACK
7
SS -> MS
CONNECT
8
SS -> MS
TERMINATION
9
SS -> MS
CHANNEL RELEASE
Specific message contents:
IMMEDIATE SETUP 2
Information element
value/remark
Protocol discriminator
'0000'B for GCC
Transaction identifier
'0001'B
Message type
'0x111011'B
Spare half octet
'0000'B
Ciphering key sequence number
PICS/PIXIT
Mobile station classmark
PICS/PIXIT
TMSI
PICS/PIXIT
Group identity
PICS/PIXIT
Compressed utdi
'00075BCD16'O
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15 SoLSA signalling
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.1 General considerations
|
This subclause applies only to mobile stations supporting SoLSA, as defined in 3GPP TS 02.43 and 3GPP TS 03.73.
Conformance requirements of clause 26 fully apply to any SoLSA MS.
The purpose of this subclause is to test these extra functional requirements for a SoLSA mobile station.
Additional to the abbreviations and definitions in TR 21.905 the definitions in subclause 20.24 are used within this subclause.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.1.1 Default message content
|
Default contents SYSTEM INFORMATION messages and default settings
For cell A and B refer to table 26.6
The following parameters shall be coded into the system information messages. Parameters shall be coded according to 3GPP TS 04.18.
SYSTEM INFORMATION TYPE 2bis, SYSTEM INFORMATION TYPE 5bis messages are not used.
SYSTEM INFORMATION TYPE 3
Default except:
Information Element
Value/remark
SI3 rest octets
Early Classmark Sending Control
Early Sending is explicitly accepted
Default message contents for other messages:
For subclause 26.15.2
same as in subclause 26.7.0
For subclause 26.15.3
same as in subclause 26.7.0
For subclause 26.15.4
same as in subclause 26.7.0
For subclause 26.15.5
same as in subclause 26.9.0
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.1.2 General initial conditions for SIM card
|
1. Following LSA values shall be defined in the fields of the EFSLL (GSM 11.11, subclause 10.4.1.2) and in the LSA descriptor files (GSM 11.11, subclause 10.4.1.3) on the SIM card used for testing:
LSA ID
CI
LAC
LAC + CI
PLMN code
LSA Priority
Idle mode support
LSA indication for idle mode
LSA1
54
66.001
-
HPLMN
0
On
Off
LSA3
9.000.000
2 +
[250..254]
HPLMN
8
On
On
2. List of values, that shall not be found in the SIM card, in order to be sure that the SoLSA MS is not subscribed to the LSA defined by the current carrier:
LSA ID
CI
LAC
LAC + CI
LSA value
[250..255]
[5000..5005]
5
5 + [5000..5005]
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.2 SoLSA signalling / RR
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.2.1 SoLSA signalling / RR / classmark interrogation
|
This procedure allows the network to request the MS to supply all its classmark information to the network.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemented in the MS, the basic connection establishment procedure may systematically fail.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.2.1.1 Conformance requirements
|
On receipt of a CLASSMARK ENQUIRY message, the MS sends a CLASSMARK CHANGE message to the network containing the Mobile Station Classmark 2 information element and depending upon the contents of this information element, possibly the Mobile Station Classmark 3 information element.
References
3GPP TS 04.18 subclauses 3.3.1.1.4.1, 3.4.11 and 9.1.11.
3GPP TS 04.13 subclause 5.2.9.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.2.1.2 Test purpose
|
To verify that if the network requests the SoLSA MS to supply all its classmark information then this information is communicated on the DCCH to the network.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.2.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
"Idle, updated", with TMSI allocated.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is switched off (or has its power removed).
The SS then sets the IMSI attach-detach flag in the SYSTEM INFORMATION messages so that the MS shall perform a location update when switched on.
The MS is switched on (or its power is re-applied). The MS then initiates a location update attempt. After the succesful completion of the location update procedure (with TMSI reallocation) the SS transmits a CLASSMARK ENQUIRY message. The MS shall be ready to transmit the CLASSMARK CHANGE message before 300 ms after the end of the CLASSMARK ENQUIRY message.
The term "ready to transmit" is defined in 3GPP TS 04.13.
Then the channel is released.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The MS is switched off (or has its power removed).
2
SS
IMSI attach-detach flag changed.
3
MS
The MS is switched on (or its power is re-applied).
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal, "CKSN" = CKSN1, "location area identification" = a, "mobile station classmark 1" and "mobile station classmark 2" including settings for ES IND and SoLSA and "mobile identity" = TMSI1.
5
SS -> MS
UA(LOCATION UPDATING REQUEST)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
7
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile identity" = new TMSI (=TMSI2).
8
MS -> SS
TMSI REALLOCATION COMPLETE
9
SS -> MS
CLASSMARK ENQUIRY
10
MS -> SS
CLASSMARK CHANGE
Contents as defined in step 6. This message shall be ready to be transmitted before 300 ms after the completion of step 9.
11
SS -> MS
CHANNEL RELEASE
Specific message contents:
LOCATION UPDATING REQUEST
Information element
Value/remark
as default except:
Mobile station Classmark 1
- ES IND
Controlled Early Classmark Sending option is implemented
Mobile station Classmark 2
- ES IND
Controlled Early Classmark Sending option is implemented
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3 SoLSA signalling / MM
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.1 SoLSA signalling / MM / location updating
|
This procedure is used to register the MS in the network. If it is not performed correctly, no call can be established.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.1.1 Location updating / accepted
|
To inform the network of the MSs additional SoLSA capability, the SoLSA MS has to send a CLASSMARK CHANGE as soon as possible during a normal location update procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.1.1.1 Conformance requirement
|
If the network accepts a location updating from the Mobile where the ES IND bit is set to 1 in the Classmark 1 and the Classmark 2 information element, the SoLSA bit is set to 1 in the classmark 2 information element and the Early Classmark Sending Control bit is set to high in SI3 Rest Octets, then the MS shall send, on the first occasion, the CLASSMARK CHANGE message.
During a contention resolution procedure, if the last timeslot of the block containing a L2 UA frame occurs at time T, then the MS shall be ready to transmit the CLASSMARK CHANGE before T + 40 ms.
The Mobile Station shall, after receiving a Location updating Accept message, store the relevant received informations and answer correctly to a paging request from the network.
This test is applicable for any SoLSA MSs with an LSA SIM supporting the SoLSA operations.
Reference(s)
3GPP TS 24.008 subclauses 4.4.4.6, 9.2.15, 10.5.1.5 and 10.5.1.6.
3GPP TS 04.18 subclauses 3.3.1.1.4.1, 9.1.11 and 10.5.2.34.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.1.1.2 Test purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during location update procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.1.1.3 Method of test
|
Initial conditions:
System Simulator:
Two cells, A and B, belonging to different location areas with location area identification a and b of the same PLMN.
IMSI attach/detach is allowed in both cells.
The T3212 time-out value is 1/10 hour in both cells.
Mobile Station:
The MS has a valid TMSI (=TMSI1) and CKSN (=CKSN1). It is "idle updated" on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has no valid TMSI. It has valid CKSN and Kc. It is "idle, updated" on cell B.
Test Procedure
The MS is made to select cell B. A normal location updating with TMSI reallocation is performed in cell B. The channel is released. The SS checks, by paging, that the MS has stored the newly allocated TMSI. The channel is released. The MS is made to select cell A. A normal location updating is performed in cell A. The LOCATION UPDATING ACCEPT message contains neither IMSI nor TMSI. The SS checks, by paging, that the MS has kept the old TMSI. The channel is released. The MS is made to select cell B. A normal location updating is performed in cell B. The LOCATION UPDATING ACCEPT message contains an IMSI. The SS checks, by paging, that the MS has deleted its TMSI and responds to paging with IMSI.
Maximum duration of test
4 minutes.
Expected sequence
Step
Direction
Message
Comments
1
SS
The RF level of cell A is lowered until the MS selects cell B.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal, "CKSN" = CKSN1, "location area identification" = a, "mobile station classmark 1" and "mobile station classmark 2" including settings for ES IND and SoLSA and "mobile identity" = TMSI1.
5
SS -> MS
UA(LOCATION UPDATING REQUEST)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
7
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile identity" = new TMSI (=TMSI2), LAI = b.
8
MS -> SS
TMSI REALLOCATION COMPLETE
9
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link. The SS waits an amount of time which is enough to guarantee that the MS is in service.
10
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" IE contains the new TMSI (= TMSI2).
11
MS -> SS
CHANNEL REQUEST
12
SS -> MS
IMMEDIATE ASSIGNMENT
13
MS -> SS
SABM (PAGING RESPONSE)
"Mobile identity" IE contains the new TMSI (= TMSI2).
"mobile station classmark 2" including settings for ES IND and SoLSA
14
SS -> MS
UA (PAGING RESPONSE)
15
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 13. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 13 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
16
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
17
SS
The RF level of cell B is lowered until the MS selects cell A.
18
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating
19
SS -> MS
IMMEDIATE ASSIGNMENT
20
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal, "CKSN" = CKSN1, "location area identification" = b, "mobile station classmark 1" and "mobile station classmark 2" including settings for ES IND and SoLSA and "mobile identity" = TMSI2.
21
SS -> MS
UA(LOCATION UPDATING REQUEST)
22
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 20. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 20 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
23
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile identity" IE not included.
24
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link. The SS waits an amount of time which is enough to guarantee that the MS is in service.
25
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" IE contains the TMSI (= TMSI2).
26
MS -> SS
CHANNEL REQUEST
27
SS -> MS
IMMEDIATE ASSIGNMENT
28
MS -> SS
SABM (PAGING RESPONSE)
"Mobile identity" IE contains the TMSI (= TMSI2).
"mobile station classmark 2" including settings for ES IND and SoLSA
29
SS -> MS
UA (PAGING RESPONSE)
30
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 28. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 28 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
31
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
32
SS
The RF level of cell A is lowered until the MS selects cell B.
33
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
34
SS -> MS
IMMEDIATE ASSIGNMENT
35
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal, "CKSN" = CKSN1, "location area identification" = a, "mobile station classmark 1" and "mobile station classmark 2" including settings for ES IND and SoLSA and "mobile identity" = TMSI2.
36
SS -> MS
UA(LOCATION UPDATING REQUEST)
"Mobile identity" IE contains IMSI.
37
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 35. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 35 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
38
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile identity" IE contains IMSI.
39
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link. The SS waits an amount of time which is enough to guarantee that the MS is in service.
40
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" IE contains the old TMSI (= TMSI2).
41
MS
The MS shall ignore this message. This is checked during 5 seconds.
42
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" IE contains the IMSI.
43
MS -> SS
CHANNEL REQUEST
44
SS -> MS
IMMEDIATE ASSIGNMENT
45
MS -> SS
SABM (PAGING RESPONSE)
"Mobile identity" IE contains the IMSI.
"mobile station classmark 2" including settings for ES IND and SoLSA
46
SS -> MS
UA (PAGING RESPONSE)
47
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 45. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 45 is required.
"mobile station classmark 2" includes settings for ES IND and SoLSA
48
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents:
LOCATION UPDATING REQUEST
Information element
Value/remark
as default except:
Mobile station Classmark 1
- ES IND
Controlled Early Classmark Sending option is implemented
Mobile station Classmark 2
- ES IND
Controlled Early Classmark Sending option is implemented
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2 SoLSA signalling / MM / MM information
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.1 General remark
|
1. The network has total control of the LSA indication in active mode.
2. Whatever the System Informations are, the LSA ID transmitted in the MM Information message has higher priority.
3. The indication of the current LSA in active mode is independent from the setting of the configurations parameters "LSA indication in idle mode" and "idle mode support" stored in the SIM in EFSLL (see 3GPP TS 11.11, subclause 10.4.1.2).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.2 Definition
|
The SoLSA MS in active mode may inform the user whether or not the serving cell is an LSA cell. The information about a serving cell is indicated in the display of the SoLSA MS.
The change out of an LSA or into an LSA may be indicated by the SoLSA MS, e.g. using a beep.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.3 Conformance requirement
|
1. It shall be possible to assign a subscriber defined identifier by the operator to each LSA (alphanumeric text up to 10 characters), which can be provided to the user in idle and active mode. As an MS manufacturer option the user may assign an icon or another form of indication to each LSA.
It shall be possible to indicate a change of localised service area during idle and active mode.
The indication is a network option (activated/deactivated by the network).
2. The network decides when to send a notification to the MS about a change of current LSA. The information will be sent from the MSC to the MS and will contain the LSA ID. This is done by adding the LSA ID of the current cell to the MM INFORMATION message. If no LSA ID is included in the MM Information message the MS shall assume that the current cell does not belong to any of the allowed LSAs for the subscriber.
The indication towards the user is optional and can be heard as e.g. a beep in the receiver or by displaying the stored LSA name that corresponds to the received LSA ID.
3. The MM INFORMATION message support is optional in the network. The MM information procedure may be invoked by the network at any time during an RR connection.
The MM information procedure consists only of the MM INFORMATION message sent from the network to the mobile station. During an RR connection, the network shall send none, one, or more MM INFORMATION messages to the mobile station. If more than one MM INFORMATION message is sent, the messages need not have the same content.
NOTE: The network may be able to select particular instants where it can send the MM INFORMATION message without adding delay to, or interrupting, any CM layer transaction, e.g. immediately after the AUTHENTICATION REQUEST message.
When the mobile station (supporting the MM INFORMATION message) receives an MM INFORMATION message, it shall accept the message and optionally use the contents to update appropriate information stored within the mobile station.
If the mobile station does not support the MM INFORMATION message the mobile station shall ignore the contents of the message and return an MM STATUS message with cause #97.
4. This IE (LSA Identity IE) may be sent by the network. The contents of this IE indicate the LSA identity of the serving cell.
5. The form of display and indication are left to manufacturer's choice.
6. If the Length of the LSA Identifier content is equal to 0, then no LSA ID is included. This is used to indicate that the MS has moved to an area where there is no LSA available for that MS.
References
Conformance requirement 1: 3GPP TS 02.43, subclause 4.2.1.
Conformance requirement 2: 3GPP TS 03.73, subclause 11.8.2.
Conformance requirement 3: 3GPP TS 24.008, subclause 4.3.6.
Conformance requirement 4: 3GPP TS 24.008, subclause 9.2.15a.5.
Conformance requirement 5: 3GPP TS 03.73, subclause 4.3.2.
Conformance requirement 6: 3GPP TS 24.008, subclause 10.5.3.11.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.4 Test Purpose
|
To verify that the SoLSA MS correctly handles the LSA information received in MM INFORMATION and performs indication accordingly.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.5 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.5.1 Initial Conditions
|
a) The SoLSA MS is in the active state of a call (U10).
b) The serving cell is cell 1 (carrier 1).
c) Parameters: same default values defined in table 20.24.1, except for the following values:
Parameter/condition
Carrier 1
LSA ID
54, 9.000.000, 250
LAC
5
CI
5000
Matching LSA on SIM
LSA1, LSA3
Escape PLMN
No
Run the following test procedure twice by using two different sets of initial conditions:
- with an LSA only SIM (see Definitions in subclause 20.24);
- with a normal LSA SIM (see Definitions in subclause 20.24).
Specific PICS statements:
-
PIXIT statements:
- Way to indicate the identity of the current LSA
- Way to indicate the change of the current LSA
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.5.2 Test Procedure
|
a) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 54 (LSA stored in the SIM).
b) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 250 (LSA not stored in the SIM).
c) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 54 (LSA stored in the SIM).
d) The SS sends an MM INFORMATION message without an LSA Identity IE.
e) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 54 (LSA stored in the SIM).
f) The SS sends an MM INFORMATION message which contains an LSA Identity IE. The value of the Length of LSA Identifier (octet 2) is set to zero (i.e. there are no LSA IDs included).
g) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 54 (LSA stored in the SIM).
h) A MM INFORMATION message including the LSA Identity IE is sent by the SS. The LSA Identity IE contains the LSA ID = 9.000.000 (LSA stored in the SIM).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.5.3 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.3.2.5.4 Test Requirements
|
1) After step a) the SoLSA MS indicates a change of LSA (a subscribed LSA is entered).
2) After step b) the SoLSA MS indicates a change of LSA (a not subscribed LSA is entered).
3) After step c) the SoLSA MS indicates a change of LSA (a subscribed LSA is entered).
4) After step d) the SoLSA MS indicates a change of LSA (a not subscribed LSA is entered).
5) After step e) the SoLSA MS indicates a change of LSA (a subscribed LSA is entered).
6) After step f) the SoLSA MS indicates a change of LSA (a not subscribed LSA is entered).
7) After step g) the SoLSA MS indicates a change of LSA (a subscribed LSA is entered).
8) After step h) the SoLSA MS indicates a change of LSA (another subscribed LSA is entered).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.4 SoLSA signalling / CC
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.4.1 SoLSA signalling / CC / call re-establishment / call present
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.4.1.1 Conformance requirement
|
1) If the call is in the "active" state or "mobile originating modify" state, the indication from MM that re-establishment is possible shall cause call control to request re-establishment from the MM-connection, suspend any further message to be sent and await the completion of the re-establishment procedure.
2) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information elements Mobile Station Classmark 2.
3) When the call control entity is notified that the MM-connection is re-established, it shall then resume the transmission of possibly suspended messages and resume user data exchange when an appropriate channel is available.
References
3GPP TS 24.008, subclauses 4.5.1.6 and 5.5.4.2.
3GPP TS 04.18 subclause 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
3GPP TS 24.008, subclauses 4.5.1.6 and 5.5.4.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.4.1.2 Test purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during the re-establishment of an ongoing call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.4.1.3 Method of test
|
Initial conditions
System Simulator:
The SS simulates cells A and B. The LAC of cell A is different from the LAC of cell B. The PLMN identities of cell A and B are equal.
The call re-establishment parameter concerning cell A is set to an arbitrary value.
Cell B is not barred, the RACH control parameters information element sent in SYSTEM INFORMATION TYPE 1 to 4 messages of cell A and B specifies "call reestablishment allowed in the cell", the NCC of cell B is indicated as permitted in the PLMN permitted information element of SYSTEM INFORMATION TYPE 2 and 6 messages of cell A. Cell B is indicated as a neighbour cell of cell A in SYSTEM INFORMATION TYPE 2 and 5 messages of cell A. Cell reselect hysteresis parameter of cell A is set to zero.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Maximum duration of test
1 minute.
Test procedure
The MS is brought to active state by using procedure 26.9.2, "structured procedures, MS originated call, early assignment". The RF level of cell A is lowered so that cell B is to be selected (when the MS performs re-establishment after radio link failure), while keeping the C1 and C2 of cell A greater than zero. SS waits for at least 5 seconds. Then the SS stops transmission on the TCH/SACCH. The MS shall re-establish the call on cell B using a CM RE-ESTABLISHMENT message. The SS performs ciphering mode setting and assignment procedures. The MS shall through-connect the appropriate bearer channel. Then, the call is cleared by the SS.
Expected sequence
Step
Direction
Message
Comments
1
Steps 1‑21 of test case 26.15.3.1 are performed (the appropriate bearer channel is through connected in both directions in TCH)
2
SS
The RF level of cell A is lowered. The SS waits at least 5 seconds. The SS stops transmission on the TCH/SACCH.
3
MS -> SS
CHANNEL REQUEST
this is sent on cell B. Establ. Cause shall be "call re-establishment; TCH/F was in use,..."
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM REESTABLISHMENT REQUEST
note specific message contents
6
SS -> MS
UA (CM REESTABLISHMENT REQUEST)
7
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 5. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 5 is required.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
SS -> MS
ASSIGNMENT COMMAND
11
MS -> SS
ASSIGNMENT COMPLETE
12
MS
The appropriate bearer channel is through connected in both directions.
13
SS -> MS
DISCONNECT
with cause value "Normal"
14
MS -> SS
RELEASE
15
SS -> MS
RELEASE COMPLETE
16
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific message contents:
CM RE-ESTABLISHMENT REQUEST
Information element
Value/remark
Protocol discriminator
Mobility Management
Skip indicator
Encoded as zeroes
Message type
CM RE-ESTABLISHMENT REQUEST
Ciphering key sequence number
The CKSN which the MS was allocated in step 6 of the procedure of subclause 26.15.3.1
Spare half octet
zero
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
Mobile identity
The TMSI that the MS is having initially
Location area identification
Corresponding the LAI of cell A
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5 SoLSA signalling / structured procedures
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.1 SoLSA signalling / structured procedures / MS originated call / early assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.1.1 Conformance requirements
|
1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.
3) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information elements Mobile Station Classmark 2.
4) Subsequently after establishment of an MM connection, the MS shall send a SETUP message with correct parameters.
5) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
- attach the user connection to the radio path;
- return a CONNECT ACKNOWLEDGE message.
6) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
7) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
References
Conformance requirement 1: 3GPP TS 02.07 subclause B.1.1.
Conformance requirement 2: 3GPP TS 04.18 subclause 3.3.1.1.
Conformance requirement 3: 3GPP TS 04.18 subclauses 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirement 4: 3GPP TS 24.008 subclause 5.2.1.
Conformance requirement 5: 3GPP TS 24.008 subclause 5.2.1.6.
Conformance requirement 6: 3GPP TS 24.008 subclause 5.4.4.
Conformance requirement 7: 3GPP TS 04.18 subclause 3.4.13.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.1.2 Test purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile originating call (MOC) with early assignment procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
PIXIT statements:
- Way to indicate mobile originated alerting.
-. Way to display the called number
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is made to initiate a call on any frequency band supported by the MS. The call is established with early assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS
If supported, the MS must display the called number in the way defined in PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. Indicating early sending of CLASSMARK CHANGE and SoLSA support
6
SS -> MS
UA (CM SERVICE REQUEST)
7
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 5. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 5 is required.
8
SS -> MS
AUTHENTICATION REQUEST
9
MS -> SS
AUTHENTICATION RESP
SRES specifies correct value.
10
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
11
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
12
SS
SS starts ciphering.
13
MS -> SS
SETUP
14
SS -> MS
CALL PROCEEDING
15
SS -> MS
ASSIGNMENT COMMAND
16
MS -> SS
ASSIGNMENT COMPLETE
17
SS -> MS
ALERTING
18
MS
Depending on the PIXIT, an alerting indication is given
19
SS -> MS
CONNECT
20
MS -> SS
CONNECT ACKNOWLEDGE
21
MS
The appropriate bearer channel is through connected in both directions.
22
SS -> MS
DISCONNECT
23
MS -> SS
RELEASE
24
SS -> MS
RELEASE COMPLETE
25
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CM SERVICE REQUEST
Information element
Value/remark
as default except:
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.2 SoLSA signalling / structured procedures / MS originated call / late assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.2.1 Conformance requirements
|
1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.
3) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information element Mobile Station Classmark 2.
4) Upon receipt of the ASSIGNMENT COMMAND message, the Mobile Station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause "normal event", to the network on the main DCCH.
5, 6) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
- attach the user connection to the radio path;
- return a CONNECT ACKNOWLEDGE message.
7) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
8) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
References
Conformance requirement 1: 3GPP TS 02.07 subclause B.1.1.
Conformance requirement 2: 3GPP TS 04.18 subclause 3.3.1.1.
Conformance requirement 3: 3GPP TS 04.18 subclause 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirement 4: 3GPP TS 04.18 subclauses 3.4.3.1 and 3.4.3.2.
Conformance requirement 5: 3GPP TS 24.008 subclause 5.2.1.6.
Conformance requirement 6: 3GPP TS 24.008 subclause 5.2.1.6.
Conformance requirement 7: 3GPP TS 24.008 subclause 5.4.4.
Conformance requirement 8: 3GPP TS 04.18 subclause 3.4.13.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.2.2 Test purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile originating call (MOC) with late assignment procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
PIXIT statements:
- Way to indicate mobile originated alerting.
-. Way to display the called number
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is made to initiate a call on any frequency band supported by the MS. The call is established with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS
If supported, the MS must display the called number in the way defined in PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. Indicating early sending of CLASSMARK CHANGE and SoLSA support
6
SS -> MS
UA (CM SERVICE REQUEST)
7
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 5. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 5 is required.
8
SS -> MS
AUTHENTICATION REQUEST
9
MS -> SS
AUTHENTICATION RESP
SRES specifies correct value.
10
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
11
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
12
SS
SS starts ciphering.
13
MS -> SS
SETUP
14
SS -> MS
CALL PROCEEDING
15
SS -> MS
ALERTING
16
MS
Depending on thePIXIT, an alerting indication is given
17
SS -> MS
ASSIGNMENT COMMAND
18
MS -> SS
ASSIGNMENT COMPLETE
19
SS -> MS
CONNECT
20
MS -> SS
CONNECT ACKNOWLEDGE
21
MS
The appropriate bearer channel is through connected in both directions.
22
SS -> MS
DISCONNECT
23
MS -> SS
RELEASE
24
SS -> MS
RELEASE COMPLETE
25
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CM SERVICE REQUEST
Information element
Value/remark
as default except:
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.3 SoLSA signalling / structured procedures / MS terminated call / early assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.3.1 Conformance requirement
|
1) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after Layer 2 UA message sent from the network.
2) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
3, 4) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with early establishment of the traffic channel
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
b) if the MS supports immediate connect, by continuing the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, by sending an ALERTING message.
5) An MS indicates acceptance of a MT call by sending CONNECT.
6) For speech calls:
The mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
For data calls:
The mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
7) The MS initiates call clearing of an active call by sending a DISCONNECT message.
8) The MS in this phase of call release, upon receipt of a RELEASE message, shall return a RELEASE COMPLETE message.
9) Subsequently the MS, upon receipt of a CHANNEL RELEASE message, shall disconnect the main signalling link.
Requirement reference:
Conformance requirement 1: 3GPP TS 04.18 subclauses 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirements 2: 3GPP TS 24.008 subclauses 5.2.2.3.1.
Conformance requirement 3, 4: 3GPP TS 04.18 subclauses 3.4.3.1 and 3.4.3.2.
Conformance requirement 5: 3GPP TS 24.008 subclause 5.2.2.5.
Conformance requirement 6: 3GPP TS 24.008 subclause 5.2.2.9.
Conformance requirement 7: 3GPP TS 24.008 subclause 5.4.3.1.
Conformance requirement 8: 3GPP TS 24.008 subclause 5.4.3.3.
Conformance requirement 9: 3GPP TS 04.18 subclause 3.4.13.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.3.2 Test Purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile terminated call (MTC) with early assignment procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel
2
MS -> SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM
"Mobile identity" IE contains the IMSI.
"mobile station classmark 2" including settings for ES IND and SoLSA.
5
SS -> MS
UA (PAGING RESPONSE)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESP
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
SS -> MS
SETUP
Message contains the signal IE.
13
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A12
MS -> SS
CONNECT
sent on the old channel
A13
SS -> MS
ASSIGNMENT COMMAND
A14
MS -> SS
ASSIGNMENT COMPLETE
B12
SS -> MS
ASSIGNMENT COMMAND
B13
MS -> SS
ASSIGNMENT COMPLETE
sent on the new channel
B14
MS -> SS
ALERTING
B15
MS
An alerting indication as defined in a PIXIT statement is given by the MS
B16
MS
The MS is made to accept the call in the way described in a PIXIT statement
B17
MS -> SS
CONNECT
18
MS
If the call is a speech call, the TCH shall be through connected in both directions.
19
SS -> MS
CONNECT ACKNOWLEDGE
20
MS
If the call is a data call, the TCH shall be through connected in both directions.
21
MS
The MS is made to release the call.
22
MS -> SS
DISCONNECT
23
SS -> MS
RELEASE
24
MS -> SS
RELEASE COMPLETE
25
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.4 SoLSA signalling / structured procedures / MS terminated call / late assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.4.1 Conformance requirement
|
1) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after Layer 2 UA message sent from the network.
2) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
3) An MS indicates acceptance of a MT call by sending CONNECT. If the MS does not support immediate connect, it sends an ALERTING message
4, 5) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with late establishment of the traffic channel:
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message.
6) For speech calls:
The mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
For data calls:
The mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
7) The MS initiates call clearing of an active call by sending a DISCONNECT message.
8) The MS in this phase of call release, upon receipt of a RELEASE message, shall return a RELEASE COMPLETE message.
9) Subsequently the MS, upon receipt of a CHANNEL RELEASE message, shall disconnect the main signalling link.
Requirement reference:
Conformance requirement 1: 3GPP TS 04.18 subclauses 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirements 2: 3GPP TS 24.008 section 5.2.2.3.1.
Conformance requirement 3, 4: 3GPP TS 04.18 subclauses 3.4.3.1 and 3.4.3.2.
Conformance requirement 5: 3GPP TS 24.008 subclause 5.2.2.5.
Conformance requirement 6: 3GPP TS 24.008 subclause 5.2.2.9.
Conformance requirement 7: 3GPP TS 24.008 subclause 5.4.3.1.
Conformance requirement 8: 3GPP TS 24.008 subclause 5.4.3.3.
Conformance requirement 9: 3GPP TS 04.18 subclause 3.4.13.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.4.2 Test Purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during a mobile terminated call (MTC) with late assignment procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is paged and a MT call is established with late assignment (after CONNECT). Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel
2
MS -> SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM
"Mobile identity" IE contains the IMSI.
"mobile station classmark 2" including settings for ES IND and SoLSA.
5
SS -> MS
UA (PAGING RESPONSE)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESP
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
SS -> MS
SETUP
Message contains the signal IE.
13
MS -> SS
CALL CONFIRMED
A14
MS -> SS
CONNECT
B14
MS -> SS
ALERTING
B15
MS
An alerting indication as defined in a PIXIT statement is given by the MS
B16
MS
The MS is made to accept the call in the way described in a PIXIT statement
B17
MS -> SS
CONNECT
18
SS -> MS
ASSIGNMENT COMMAND
19
MS -> SS
ASSIGNMENT COMPLETE
20
MS
If the call is a speech call, the TCH shall be through connected in both directions.
21
SS -> MS
CONNECT ACKNOWLEDGE
22
MS
If the call is a data call, the TCH shall be through connected in both directions.
23
MS
The MS is made to release the call.
24
MS -> SS
DISCONNECT
25
SS -> MS
RELEASE
26
MS -> SS
RELEASE COMPLETE
27
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.5 SoLSA signalling / structured procedures / emergency call / idle updated
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.5.1 Conformance requirements
|
1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct CKSN and TMSI , with CM Service Type "emergency call establishment" and indicating early sending of classmark change and SoLSA support.
3) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information elements Mobile Station Classmark 2.
4) Authentication and cipher mode setting shall be performed successfully.
5) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
6), 7) The emergency call shall be correctly established. The assignment procedure shall be correctly performed.
8) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH shall be through connected in both directions if an appropriate TCH is available.
9) The call shall be cleared correctly.
Requirement Reference:
Conformance requirement 1 and 2: 3GPP TS 04.18 subclause 3.3.1.1,
3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5,
3GPP TS 02.30 subclause 4.2.2.
Conformance requirement 3: 3GPP TS 04.18 subclauses 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirement 4: 3GPP TS 04.18, subclause 3.4.7,
3GPP TS 24.008 subclause 4.3.2.
Conformance requirement 5: 3GPP TS 24.008, subclause 5.2.1.
Conformance requirement 6 and 7: 3GPP TS 04.18, subclause 3.4.3.
Conformance requirement 8: 3GPP TS 24.008, section 5.2.1.6.
Conformance requirement 9: 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.5.2 Test purpose
|
To verify that the SoLSA MS supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during an Emergency Call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.5.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
- Use of R99 Emergency numbers (TSPC_R99_Emerg)
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate an emergency call. The call is established with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The classmark 2 IE indicates early sending of CLASSMARK CHANGE and SoLSA support
5
SS -> MS
UA (CM SERVICE REQUEST)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
MS -> SS
EMERGENCY SETUP
If a half rate speech service is supported, the message must contain one bearer capability IE indicating in the radio channel requirement field "dual rate/half rate preferred" or "dual rate/full rate preferred". If no half rate speech service is supported, the message must either contain no bearer capability IE or contain one bearer capability IE indicating in the radio channel requirement field "full rate channel".
13
SS -> MS
CALL PROCEEDING
14
SS -> MS
ALERTING
15
SS -> MS
ASSIGNMENT COMMAND
The rate of the channel is that one indicated by the EMERGENCY SETUP message, if that message did not offer a choice, and the rate is the preferred one else.
16
MS -> SS
ASSIGNMENT COMPLETE
17
SS -> MS
CONNECT
18
MS -> SS
CONNECT ACKNOWLEDGE
19
MS
The TCH is through connected in both directions.
20
SS -> MS
DISCONNECT
21
MS -> SS
RELEASE
22
SS -> MS
RELEASE COMPLETE
23
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CM SERVICE REQUEST
Information element
Value/remark
as default except:
CM Service type
Emergency call establishment
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.6 SoLSA signalling / structured procedures / emergency call / idle, no IMSI
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.6.1 Conformance requirements
|
1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct IMEI and a non-available CKSN, with CM Service Type "emergency call establishment" and indicating early sending of classmark change and SoLSA support.
3) After the initial message the SoLSA MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information elements Mobile Station Classmark 2.
4) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
5), 6) The emergency call shall be correctly established. The assignment procedure shall be correctly performed.
7) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH shall be through connected in both directions if an appropriate TCH is available.
8) The call shall be cleared correctly.
Requirement Reference:
Conformance requirement 1 and 2: 3GPP TS 04.18 subclause 3.3.1.1,
3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5,
3GPP TS 02.30 subclause 4.2.2.
Conformance requirement 3: 3GPP TS 04.18 subclauses 3.3.1.1.4.1 and 9.1.11,
3GPP TS 03.73 subclause 11.4.1,
3GPP TS 24.008 subclauses 9.2.9, 9.2.15, 10.5.1.5 and 10.5.1.6.
Conformance requirement 4: 3GPP TS 24.008, subclause 5.2.1.
Conformance requirement 5 and 6: 3GPP TS 04.18, subclause 3.4.3.
Conformance requirement 7: 3GPP TS 24.008, subclause 5.2.1.6.
Conformance requirement 8: 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.6.2 Test purpose
|
To verify that the SoLSA MS in the "idle, no IMSI" state (no SIM inserted), supports "early classmark sending procedure", e.g. sending information to the network about SoLSA support during an Emergency Call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.15.5.6.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI" no SIM inserted.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Speech supported for Half rate version 3 (GSM HR) (TSPC_AddInfo_Half_rate_version_3)
- Use of R99 Emergency numbers (TSPC_R99_Emerg)
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI" no SIM inserted.
Test procedure
The MS is made to initiate an emergency call. The call is established without authentication, without ciphering, with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The mobile identity IE specifies the IMEI of the MS. The cipher key sequence number IE indicates "no key is available". The classmark 2 IE indicates early sending of CLASSMARK CHANGE and SoLSA support
5
SS -> MS
UA (CM SERVICE REQUEST)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. "mobile station classmark 2" includes settings for ES IND and SoLSA
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
7
SS -> MS
CM SERVICE ACCEPT
8
MS -> SS
EMERGENCY SETUP
If a half rate speech service is supported, the message must contain one bearer capability IE indicating in the radio channel requirement field "dual rate/half rate preferred" or "dual rate/full rate preferred". If no half rate speech service is supported, the message must either contain no bearer capability IE or contain one bearer capability IE indicating in the radio channel requirement field "full rate channel".
9
SS -> MS
CALL PROCEEDING
10
SS -> MS
ALERTING
11
SS -> MS
ASSIGNMENT COMMAND
The rate of the channel is that one indicated by the EMERGENCY SETUP message, if that message did not offer a choice, and the rate is the preferred one else.
12
MS -> SS
ASSIGNMENT COMPLETE
13
SS -> MS
CONNECT
14
MS -> SS
CONNECT ACKNOWLEDGE
15
MS
The TCH is through connected in both directions.
16
SS -> MS
DISCONNECT
17
MS -> SS
RELEASE
18
SS -> MS
RELEASE COMPLETE
19
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
CM SERVICE REQUEST
Information element
Value/remark
as default except:
CM Service type
Emergency call establishment
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- SoLSA
SoLSA supported
CLASSMARK CHANGE
Information element
Value/remark
as default except:
Mobile station Classmark 2
-ES IND
Controlled Early Classmark Sending is implemented.
-SoLSA
SoLSA supported
26.16 Adaptive Multi Rate Signalling
The purpose of this subclause is to test the different procedures, which may be impacted by the multi rate codec.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.0 Default contents of layer 3 messages for AMR signalling tests
|
Refer to table 26.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.1 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.2 Inband Signalling, Uplink Codec Adaptation
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.2.1 Conformance Requirement
|
The MS shall after reception of a Codec Mode Command apply the corresponding codec mode in the uplink direction for the next possible speech frame and no more than three speech frames later. This test is not intended to verify these conformance requirements, but to verify the correctness of the involved layer 1 and layer 3 signalling.
References:
3GPP TS 05.09 subclauses 3.3 and 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.2.2 Test Purpose
|
This test is concerned with the link adaptation for AMR uplink and the related inband signalling. The test shall verify that the MS in the uplink direction applies the codec mode indicated by the network transmitted Codec Mode Commands, and that the MS correctly signals the used codec as Codec Mode Indication in the uplink inband signalling.
NOTE: The inband signals are L1 signalling transmitted every speech frame, as defined in 3GPP TS 05.09: In uplink directions Codec Mode Requests and Codec Mode Indications are transmitted alternately, whereas downlink signalling contains of alternately Codec Mode Commands and Codec Mode Indications.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.2.3 Method of Test
|
Initial Conditions
The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
a) A mobile originated call is initiated, following the CHANNEL REQUEST received from the MS the SS sends an IMMEDIATE ASSIGNMENT to the MS commanding it to go to a SDCCH. The MS indicates to the SS that it supports the multi-rate speech codec. The SS allocates the MS a TCH/AFS and signals the allowed codec subset and adaptation thresholds as part of the ASSIGNMENT COMMAND. DTX shall not be activated. Hopping is activated. The hopping band is centred around an ARFCN in the Mid ARFCN range. The hopping frequencies are chosen from those defined in clause 6.
The following active codec mode subset shall apply:
Codec Mode
TCH/AFS in kbit/s
CODEC_MODE_1
4,75
CODEC_MODE_2
5,9
CODEC_MODE_3
7,95
CODEC_MODE_4
12,2
The following decision threshold and hysteresis values in terms of normalized carrier to interference ratio (C/Inorm), shall apply for Codec Mode Command / Request (MC', MR'):
MC'/MR'
THR_MC_Dn(MC')/
THR_MR_Dn(MR')
THR_MC_Up(MC')/
THR_MR_Up(MR')
CODEC_MODE_4
16,5 dB
+
CODEC_MODE_3
11,5 dB
18,5 dB
CODEC_MODE_2
6,5 dB
13,5 dB
CODEC_MODE_1
8,5 dB
b) The SS signals that a new codec is wanted in uplink direction by changing the value of the Codec Mode Command. The MS shall apply the commanded mode in uplink by changing the mode and correspondingly the value of the Codec Mode Indication to match the used codec. This is repeated for all neighbouring mode transitions in the Active Codec Set.
c) If the MS supports TCH/AHS the SS sends an ASSIGNMENT COMMAND allocating the MS a TCH/AHS and signals the allowed codec subset and adaptation thresholds as part of the ASSIGNMENT COMMAND. DTX shall not be activated. Hopping is activated. The hopping band is centred around an ARFCN in the Mid ARFCN range. The hopping frequencies are chosen from those defined in clause 6.
The following active codec mode subset shall apply:
Codec Mode
TCH/AHS in kbit/s
CODEC_MODE_1
5,15
CODEC_MODE_2
6,7
CODEC_MODE_3
7,95
The following decision threshold and hysteresis values in terms of normalized carrier to interference ratio (C/Inorm), shall apply for Codec Mode Command / Request (MC', MR'):
MC'/MR'
THR_MC_Dn(MC')/
THR_MR_Dn(MR')
THR_MC_Up(MC')/
THR_MR_Up(MR')
CODEC_MODE_3
12,5 dB
+
CODEC_MODE_2
11,0 dB
15,0 dB
CODEC_MODE_1
13,0 dB
d) Step b) is repeated for the settings given in step c).
Maximum Duration of Test
2 minutes
Expected Sequence in step b)
Step
Direction
Message
Comments
A1
SS->MS
Codec Mode Command change
Codec Mode 3 is commanded by inband signalling
A2
MS->SS
Codec Mode Indication change
Codec Mode Indication shows current active mode in uplink, thus changed when mode changes
3
SS->MS
Codec Mode Command change
Codec Mode 2 is commanded by inband signalling
4
MS->SS
Codec Mode Indication change
Codec Mode 2 is indicated in inband signalling with first frame using Codec Mode 2
5
SS->MS
Codec Mode Command change
Codec Mode 1 is commanded by changing inband signal
6
MS->SS
Codec Mode Indication change
Codec Mode 1 is indicated in inband signalling with first frame using Codec Mode 1.
7
SS->MS
Codec Mode Command change
Codec Mode 2 is commanded by changing inband signal
8
MS->SS
Codec Mode Indication change
Codec Mode 2 is indicated in inband signalling with first frame using Codec Mode 2.
9
SS->MS
Codec Mode Command change
Codec Mode 3 is commanded by changing inband signal
10
MS->SS
Codec Mode Indication change
Codec Mode 3 is indicated in inband signalling with first frame using Codec Mode 3.
A11
SS->MS
Codec Mode Command change
Codec Mode 4 is commanded by changing inband signal
A12
MS->SS
Codec Mode Indication change
Codec Mode 4 is indicated in inband signalling with first frame using Codec Mode 4
In TCH/AHS the Active Codec Set contains only three of four possible codecs, thus steps prefixing A are not implemented in this case.
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
Value/remark
Assignment Command
In step a) of Test Procedure: codec mode 4 selected (codec mode 3 for TCH/AHS)
(ref: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.2)
Codec mode commands, downlink inband signalling
Information Element
Value/remark
Channel Mode to be used for uplink
In step a) of Test Procedure: Codec Mode 4 commanded in AFS and Codec Mode 3 in AHS
In step 1-2: Codec Mode 3 commanded
In step 3-4: Codec Mode 2 commanded
In step 5-6: Codec Mode 1 commanded
In step 7-8: Codec Mode 2 commanded
In step 9-10: Codec Mode 3 commanded
In step 11-12: Codec Mode 4 commanded
Codec mode indications, uplink inband signalling
Information Element
Value/remark
Indicating Codec Mode currently used uplink
In step a) of Test Procedure: Codec Mode 4 indicated in AFS and Codec Mode 3 in AHS
In step 1: Codec Mode 4 indicated in AFS (step ignored in AHS)
In step 2-3: Codec Mode 3 indicated
In step 4-5: Codec Mode 2 indicated
In step 6-7: Codec Mode 1 indicated
In step 8-9: Codec Mode 2 indicated
In step 10-11: Codec Mode 3 indicated
In step 12: Codec Mode 4 indicated
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.3 Structured procedures / MS terminated call / early assignment / no initial codec mode
|
NOTE: This test is derived from the one described in subclause 26.12 and entitled: "Structured procedures / MS terminated call / early assignment"
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.3.1 Conformance requirement
|
1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) The ASSIGNMENT command will not specify which of the codec modes the MS should use, but allow the handset to select the default codec mode.
4) For speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
CHx: identifies any of the Channel Codec mode.
FR: full rate channel.
HR: half rate channel.
References:
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.1.2 and 9.1.5.
3GPP TS 05.09 subclause 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.3.2 Test purpose
|
1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) To verify that upon receipt of an ASSIGNMENT COMMAND with no codec mode specified, the MS shall use the default codec mode.
4) To verify that for speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.3.3 Method of Test
|
Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
The following test is performed for both channel modes of the multi-rate codec, i.e. full rate and half rate:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M = 1, 2, 3, 4.
This test is repeated for K=1, and where the MS supports half rate version 3 K=2.
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on the correct paging sub-channel
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
SETUP
11
MS->SS
CALL CONFIRMED
If the MS supports an Immediate connection then branch A applies. If the MS doesn't support an immediate connection then branch B applies.
A12
MS->SS
CONNECT
sent on the old channel
A13
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes, but does not identify a mode for immediate operation.
A14
MS->SS
ASSIGNMENT COMPLETE
B12
SS->MS
ASSIGNMENT COMMAND
B13
MS->SS
ASSIGNMENT COMPLETE
Sent on the new channel. SS allocates allowed subset codec modes, but does not identify a mode for immediate operation.
B14
MS->SS
ALERTING
B15
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
B16
MS
The MS is made to accept the call.
B17
MS->SS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the default codec mode specified.
19
SS->MS
CONNECT ACK
20
MS
The MS is made to release the call.
21
MS->SS
DISCONNECT
22
SS->MS
RELEASE
23
MS->SS
RELEASE COMPLETE
24
SS->MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
1 codec mode specified
M=2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
2 codec modes and threshold values specified
M=3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
3 codec modes and threshold values specified
M = 4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
4 codec modes and threshold values specified
K = 1
Assignment Command
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 3
K = 2
This step is applicable only if the MS supports half rate version 3.
Assignment Command
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
26.16.3a Structured procedures / MS terminated call / early assignment / specified initial codec mode
NOTE: this test is derived from the one described in subclause 26.12 and entitled: "Structured procedures / MS terminated call / early assignment"
26.16.3a.1 Conformance requirement
1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) The ASSIGNMENT COMMAND will specify the subset of codec modes that the MS is allowed to use for the call, the thresholds and the initial codec mode for immediate use by the MS.
4) For speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
CHx: identifies any of the Channel Codec mode.
FR: full rate channel.
HR: half rate channel.
References:
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 05.09 subclause 3.4.
26.16.3a.2 Test purpose
1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying using CHx-FR or CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) To verify that upon receipt of an ASSIGNMENT COMMAND with codec mode specified, the MS shall use that specified codec mode.
4) To verify that for speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
26.16.3a.3 Method of Test
Initial Conditions
SS 1 cell, default parameters
MS in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
The following test is performed for both channel modes of the multi-rate codec, i.e. full rate and half rate:
A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M=1,2,3,4.
This test is repeated for K=1, and where the MS supports half rate version 3 K=2.
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on the correct paging sub-channel
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
SETUP
11
MS->SS
CALL CONFIRMED
If the MS supports an Immediate connection then branch A applies. If the MS doesn’t support an immediate connection then branch B applies.
A12
MS->SS
CONNECT
sent on the old channel
A13
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes and identifies a mode for immediate operation.
A14
MS->SS
ASSIGNMENT COMPLETE
B12
SS->MS
ASSIGNMENT COMMAND
B13
MS->SS
ASSIGNMENT COMPLETE
SS allocates allowed subset codec modes and identifies a mode for immediate operation.
B14
MS->SS
ALERTING
B15
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
B16
MS
The MS is made to accept the call.
B17
MS->SS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
19
SS->MS
CONNECT ACK
20
MS
The MS is made to release the call.
21
MS->SS
DISCONNECT
22
SS->MS
RELEASE
23
MS->SS
RELEASE COMPLETE
24
SS->MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Content
M=1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Start Mode specified
1 codec mode specified
M=2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Start Mode specified
2 codec modes and threshold vales specified
M=3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Start Mode specified
3 codec modes and threshold vales specified
M=4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Start Mode specified
4 codec modes and threshold vales specified
K = 1
Assignment Command
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
K = 2
This step is applicable only if the MS supports half rate version 3.
Assignment Command
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.4 Structured procedures / MS originated call / late assignment / specified initial codec mode
|
NOTE: This test is derived from the one described in subclause 26.12 and entitled: "Structured procedures / MS terminated call / early assignment".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.4.1 Conformance requirement
|
1) The MS shall indicate and include in the mobile originating SETUP for speech call all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message using full rate version 3 or half rate version 3, the Mobile Station starts a normal channel assignment procedure. It means that the MS initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause 'normal event', to the network on the main DCCH.
References:
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 05.09 subclause 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.4.2 Test purpose
|
1) To verify that the MS indicates and includes in the mobile originating SETUP for speech call all the speech versions that it supports.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating using full rate version 3 or half rate version 3, the MS sends an ASSIGNMENT COMPLETE message. The ASSIGNMENT COMMAND message will also identify which codec mode the MS is allowed to use for the call, the threshold values and the initial codec mode for immediate use.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.4.3 Method of Test
|
Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
- Way to indicate mobile originated alerting.
Foreseen Final State of MS
The MS has a MO call in state U10, "active".
Test Procedure
The following test is performed for both channel modes of the multi-rate codec, i.e. full rate and half rate.
The MS is made to initiate a speech call. The call is established with a late assignment.
Maximum Duration of Test
3 minutes.
Expected Sequence
This test is repeated for M = 1, 2, 3, 4.
For each M, this test is repeated for K=1, and where the MS supports half rate version 3 K=2.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
SETUP
The MS indicates it supports the FR version 3 speech and if supported, HR version 3 speech also.
11
SS->MS
CALL PROCEEDING
12
SS->MS
ALERTING
13
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
14
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes, but does identifies a mode for immediate operation.
15
MS->SS
ASSIGNMENT COMPLETE
16
SS->MS
CONNECT
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
MS->SS
CONNECT ACK
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 1
Start mode specified
1 codec mode specified
M=2
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 1
Start mode specified
2 codec modes and threshold vales specified
M=3
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 1
Start mode specified
3 codec modes and threshold vales specified
M = 4
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 1
Start mode specified
4 codec modes and threshold vales specified
26.16.4a Structured procedures / MS originated call / late assignment / no initial codec mode
NOTE: This test is derived from the one described in subclause 26.16.4 and entitled: "Structured procedures / MS originated call / late assignment / specified initial codec mode".
26.16.4a.1 Conformance requirement
1) The MS shall indicate and include in the mobile originating SETUP for speech call all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message using full rate version 3 or half rate version 3, the Mobile Station starts a normal channel assignment procedure. It means that the MS initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause 'normal event', to the network on the main DCCH. The ASSIGNMENT COMMAND message will also specify the subset of codec modes that the MS is allowed to use for the call and the threshold values. The ASSIGNMENT COMMAND will not specify the initial codec mode but will, rather, allow the MS to select the default codec mode.
If the Initial Codec Mode is not signalled, then the default Initial Codec Mode is given by the following implicit rule. If the Active Codec Set contains:
1 mode, then this hall be the Initial Codec Mode.
2 or 3 modes, then the Initial Codec mode shall be the most robust mode of the set (with lowest bit rate).
4 modes, then the Initial Codec Mode shall be the second most robust mode of the set (with second lowest bit rate. If the Active Codec Set is changed during the call, then this default Initial Codec Mode shall used until an other ICM is explicitly signalled.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 05.09 subclause 3.4.
26.16.4a.2 Test purpose
1) To verify that the MS indicates and includes in the mobile originating SETUP for speech call all the speech versions that it supports.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating using speech full rate version 3 or speech half rate version 3, the MS sends an ASSIGNMENT COMPLETE message. The ASSIGNMENT COMMAND message will also specify the subset of codec modes that the MS is allowed to use for the call and the threshold values. The ASSIGNMENT COMMAND will not specify the initial codec mode but will, rather, allow the MS to select the default codec mode.
26.16.4a.3 Method of Test
Initial Conditions
SS 1 cell, default parameters
MS in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
- Way to indicate mobile originated alerting.
Foreseen Final State of MS
The MS has a MO call in state U10, "active".
Test Procedure
The following test is performed for both channel modes of the multi-rate codec, i.e. full rate and half rate.
The MS is made to initiate a speech call. The call is established with a late assignment.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M=1,2,3,4.
For each M, this test is repeated for K=1, and where the MS supports half rate version 3 K=2.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
SETUP
The MS indicates it supports the FR version 3 speech and if supported, HR version 3 speech also.
12
SS->MS
CALL PROCEEDING
13
SS->MS
ALERTING
14
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
15
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset of codec modes and thresholds, but does not identify a mode for immediate operation.
16
MS->SS
ASSIGNMENT COMPLETE
17
SS->MS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified (M=1 CMI=0, M=2 CMI=0, M=3 CMI=0, M=4 CMI=1).
19
MS->SS
CONNECT ACK
Specific Message Content
M=1
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 0
1 codec mode specified
M=2
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 0
2 codec modes and threshold vales specified
M=3
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 0
3 codec modes and threshold vales specified
M=4
Assignment Command
Information Element
value/remark
Channel mode
Mode
If K=1 Speech full rate version 3
If K=2 Speech half rate version 3
Multi-Rate configuration
ICMI = 0
4 codec modes and threshold vales specified
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.5 AMR signalling / Handover / active call / successful case
|
NOTE: This test is derived from 26.12.2 – EFR Signalling/Handover/active call/successful case.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.5.1 Conformance requirements
|
The MS shall correctly apply the handover procedure in the non-synchronised case when:
- a call is in progress; and
- handover is performed from a TCH/F with/without frequency hopping towards a TCH/F with/without frequency hopping;
- the mode of either the current or the target channel is set to full rate speech version 3.
The MS also supporting half rate speech version 3 shall correctly apply the handover procedure in the non-synchronized case when:
- a call is in progress; and
- a handover is performed between a TCH/H with/without frequency hopping and a TCH/F or TCH/H with/without frequency hopping; and
- the mode of either the current or the target channel is set to half rate speech version 3.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.4 and 9.1.15.
3GPP TS 04.13 subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.5.2 Test Purpose
|
To test that the MS shall correctly apply the handover procedure in the non-synchronized case when:
- a call is in progress; and
- handover is performed from a TCH/F with/without frequency hopping towards a TCH/F with/without frequency hopping; and
- the mode of either the current or the target channel is set to full rate speech version 3 (AMR full rate speech).
To test that the MS also supporting half rate shall correctly apply the handover procedure in the non-synchronized case when:
- a call is in progress; and
- a handover is performed between a TCH/H with/without frequency hopping and a TCH/F with/without frequency hopping; and
- the mode of either the current or the target channel is set to half rate speech version 3.
26.16.5.3 Method of Test
Initial Conditions
MS in call active state U10 on cell A.
SS 2 cells, A and B with same LAI, default parameters except:
Band
Cell A
Cell B
Both Cells
BCCH ARFCN
Cell Allocation
BCCH ARFCN
Cell Allocation
Format
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291
274
260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291
Range 128
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338
321
307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338
Range 128
GSM 710
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 750
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241
167
141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241
Range 128
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114
40
14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114
Bitmap 0
DCS 1 800
747
734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844
764
739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
Range 256
PCS 1 900
647
634, 641, 647, 654, 659, 662, 666, 667, 673, 675, 679, 682, 691, 698, 729, 732, 744
664
639, 643, 646, 649, 656, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Range 256
The frame numbers of cells A and B shall be different by 100.
The time base of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR) (TSPC_AddInfo_Half_rate_version_3)
- Speech supported for Full rate version 2 (GSM EFR) (TSPC_AddInfo_Full_rate_version_2)
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
PIXIT statements:
-.
Foreseen Final State of MS
The MS has a MO call in state U10, "active".
Test Procedure
Table 1
Exec
Counter
From
To
Timing Adv.
Start
Time
1
TCH/F, sv3, no FH
TCH/F, sv3, no FH
20
none
2
TCH/F, sv3, no FH
TCH/F, sv3, FH
arbitrary
none
3
TCH/F, sv3, FH
TCH/F, sv3, FH
20
1,1s
4
TCH/F, sv3, FH
TCH/F, sv3, no FH
20
none
5
TCH/F, sv3, no FH
TCH/F, sv1, no FH
20
none
6
TCH/F, sv1, no FH
TCH/F, sv3, no FH
arbitrary
none
7
TCH/F, sv3, no FH
TCH/F, sv2, FH
arbitrary
none
8
TCH/F, sv2, FH
TCH/F, sv3,FH
20
1,1
9
TCH/F, sv3, FH
TCH/H, sv1, FH
arbitrary
none
10
TCH/H, sv1, FH
TCH/F, sv3, noFH
20
none
11
TCH/F, sv3, noFH
TCH/H, sv3, FH
arbitrary
1.1
12
TCH/H, sv3, FH
TCH/H, sv3, no FH
20
none
13
TCH/H, sv3, no FH
TCH/F, sv1, no FH
20
none
14
TCH/F, sv1, no FH
TCH/H, sv3, no FH
arbitrary
none
15
TCH/H, sv3, no FH
TCH/F, sv2, FH
arbitrary
none
16
TCH/F, sv2, FH
TCH/H, sv3,FH
20
1,1
17
TCH/H, sv3, FH
TCH/H, sv1, FH
arbitrary
none
18
TCH/H, sv1, FH
TCH/H, sv3, noFH
20
none
19
TCH/H, sv3, noFH
TCH/F, sv3, no FH
20
none
Note: for all execution counters: State of call is U10 and the handover procedure is non-synchronized
sv1 stands for speech full/half rate version 1.
sv2 stands for speech full rate version 2 (enhanced full rate).
sv3 stands for speech full/half rate version 3 (AMR).
Table 2
TCH/FS
TCH/HS
SDCCH
n
10-20
5-10
2-5
n: number of access bursts.
The MS is in the active state (U10) of a call. The SS sends a HANDOVER COMMAND on the main DCCH. The MS shall (at the time defined by the Starting Time information element, if included in the message) begin to send access bursts on the new DCCH (and optionally on the SACCH) of the target cell. The SS observes the access bursts and after receiving n (n being arbitrarily chosen between values according to table 2) access bursts, the SS sends one PHYSICAL INFORMATION message with a Timing Advance as specified in table 1. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message, before 'x' ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS.
The term 'ready to transmit' is defined in 3GPP TS 04.13. The value of 'x' depends upon the target channel and is specified in the specific message contents section.
Maximum Duration of Test
10 minutes.
Expected Sequence
This sequence is performed for an execution counter M = 1, 2..10 for an MS that supports TCH/F and speech version 3, version 2 and version 1. Steps M=7 and M=8 are performed only if an MS supports full rate speech version 2. Steps M=9 and M=10 are performed only if an MS supports half rate speech version 1.
This sequence is performed for an execution counter M = 1, 2..19 for an MS that supports TCH/F and TCH/H and speech version 3, version 2 and version 1. Steps M=7, M=8, M=15 and M=16 are performed only if an MS supports speech version 2. Steps M=9, M=10, M=17 and M=18 are performed only if an MS supports half rate speech version 1.
Step
Direction
Message
Comments
0
MS -> SS
The MS and SS are in the active state of a call on the channel described below.
1
SS -> MS
HANDOVER COMMAND
See Specific message contents
2
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND. If the HANDOVER COMMAND includes a starting time IE then the first HANDOVER ACCESS message shall be transmitted in the indicated frame (unless the indicated frame is not used by that channel, in which case the next frame used by that channel shall be used)
3
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS messages. See specific message contents.
4
MS -> SS
SABM
Sent without information field
5
SS -> MS
UA
6
MS -> SS
HANDOVER COMPLETE
The message shall be ready to be transmitted before 'x' ms after the completion of step 3.
7
MS -> SS
The MS and SS are in the active state of a call on the TCH described below. The SS checks that the TCH is through connected in the correct mode.
Specific Message Contents
For M = 1:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
0
- Training Sequence Code
Chosen arbitrarily
- ARFCN
Chosen arbitrarily from the CA
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel.
- Mode
speech full rate version 3
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 263
GSM480: 310
GSM900: 20
GSM1800: 747
PCS1900: 647
GSM710: 457
GSM750: 457
T-GSM 810: 457
GSM850: 147
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N-1), where N is the number of frequencies encoded in the Frequency List IE or Frequency Channel Sequence IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronisation Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
IE Present only for GSM450 and GSM480
- Frequency List
GSM450: Allocates the following 12 frequencies (259,
261, 263, 265, 277, 279, 281, 283, 285, 287, 289, 291)
GSM480: Allocates the following 12 frequencies (306, 308, 310, 312, 324, 326, 328, 330, 332, 334, 336, 338)
Frequency Channel Sequence after time
IE Present only for GSM900, GSM 710, GSM750 and T-GSM 810
- Frequency Channel Sequence
GSM900: Allocates the following 12 frequencies (10, 17, 20, 26, 59, 66, 73, 74, 75, 76,108, 114)
GSM710, GSM 750 and T-GSM 810: Allocates the following 12 frequencies (447, 454, 457, 463, 496, 498, 500, 501, 502, 503, 506, 508)
Frequency Short List after time
IE Present only for GSM1800, PCS1900 and GSM850
- Frequency List
GSM1800: Use Range 256 to encode the following 9 frequencies: (747, 775, 779, 782, 791, 798, 829, 832, 844)
PCS1900: Use Range 256 to encode the following 9 frequencies: (647, 675, 679, 682, 691, 698, 729, 732, 744)
GSM850: Allocates the following 12 frequencies (137, 144, 147, 153, 186, 193, 200, 201, 202, 203, 235, 241)
Multi-Rate configuration IE is not included
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 3 and in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
1
- HSN
zero for cyclic
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Out of range timing advance shall trigger a handover failure procedure.
Frequency List after time
- Frequency List
Use Range 128 to encode the following 2 frequencies: GSM450: (260, 291)
GSM480: (307, 338)
GSM900: (14, 114)
GSM1800: (749, 844)
PCS1900: (649, 744)
GSM710: (451, 508)
GSM750: (451, 508)
T-GSM810: (451, 508)
GSM850: (141, 241)
Mode of the first channel.
- Mode
speech full rate version 3
Starting Time
Indicates the frame number of cell B that will occur approximately 1,1 seconds (238 frames have elapsed) after the HANDOVER COMMAND is sent by cell A.
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in hopping mode on cell B.
For M = 4:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 3 and in hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 263
GSM480: 310
GSM900: 20
GSM1800: 747
PCS1900: 647
GSM710: 457
GSM750: 457
T-GSM810: 457
GSM850: 147
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- ARFCN
The ARFCN of the BCCH Carrier
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel IE is not included
Multi-Rate configuration IE is not included
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell A.
For M = 5:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- ARFCN
Chosen arbitrarily from the CA
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel.
- Mode
speech full rate or half rate version 1
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 1 and in non-hopping mode on cell B.
For M = 6:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 1 and in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 263
GSM480: 310
GSM900: 20
GSM1800: 747
PCS1900: 647
GSM710: 457
GSM750: 457
T-GSM810: 457
GSM850: 147
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- ARFCN
Chosen arbitrarily from the CA
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel
- Mode
speech full rate version 3
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell A.
For M = 7:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set ( 0, 1 to N-1 ), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set
(1,2,..63)
Frequency List after time
- Frequency List
GSM450: use Range 128 to encode the following 12 frequencies: (260, 262, 264, 266, 276, 279, 281, 283, 285, 287, 289, 291)
GSM480: use Range 128 to encode the following 12 frequencies: (307, 309, 311, 313, 323, 326, 328, 330, 332, 334, 336, 338)
GSM900: use bit map 0 to allocates the following 12 frequencies: (14, 18, 22, 24, 60, 66, 73, 74, 75, 76,108, 114)
GSM1800: Use Range 1024 to allocate the following 12 frequencies: (749, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
PCS1900: Use Range 1024 to allocate the following 12 frequencies: (649, 658, 661, 664, 671, 679, 682, 791, 798, 729, 732, 744)
GSM710, GSM 750 and T-GSM 810: Use 128 range to allocates the following 12 frequencies: (451, 455, 459, 461, 497, 498, 500, 501, 502, 503,506, 508)
GSM850: Use 128 range to allocates the following 12 frequencies: (141, 145, 149, 151, 187, 193, 200, 201, 202, 203, 235, 241)
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel
- Mode
speech full rate version 2
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with full rate speech version 2 and in hopping mode on cell B.
For M = 8:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 2 and hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 263
GSM480: 310
GSM900: 20
GSM1800: 747
PCS1900: 647
GSM710: 457
GSM750: 457
T-GSM810: 457
GSM850: 147
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set ( 0, 1 to N-1 ), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set ( 1,2,..63 )
Synchronisation Indication IE is not included.
Mode of the first channel.
- Mode
speech full rate version 3
Frequency List after time
IE Present only for GSM450, GSM480 and GSM850
- Frequency List
GSM450: Allocates the following 12 frequencies (259, 261, 263, 265, 277, 279, 281, 283, 285, 287, 289, 291)
GSM480: Allocates the following 12 frequencies (306, 308, 310, 312, 324, 326, 328, 330, 332, 334, 336, 338)
GSM850: Allocates the following 12 frequencies (137, 144, 147, 153, 186, 193, 200, 201, 202, 203, 235, 241)
Frequency Channel Sequence after time
IE Present only for GSM900, GSM 710, GSM750 and T-GSM 810
- Frequency Channel Sequence
GSM900: Allocates the following 12 frequencies (10, 17, 20, 26, 59, 66, 73, 74, 75, 76,108, 114)
GSM710, GSM 750 and T-GSM 810: Allocates the following 12 frequencies (447, 454, 457, 463, 496, 498, 500, 501, 502, 503, 506, 508)
Frequency Short List after time
IE Present only for GSM1800 and PCS1900
- Frequency List
GSM1800: Use Range 256 to encode the following 9 frequencies: (747, 775, 779, 782, 791, 798, 829, 832, 844)
PCS1900: Use Range 256 to encode the following 9 frequencies: (647, 675, 679, 682, 691, 698, 629, 632, 644)
Starting Time
Indicates the frame number of cell B. that will occur approximately 1,1 seconds ( 238 frames have elapsed ) after the HANDOVER COMMAND is sent by cell A.
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and hopping mode on cell A.
For M = 9:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 3 and in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/H + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set ( 0, 1 to N-1 ), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set
(1,2,..63)
Frequency List after time
- Frequency List
GSM450: use Range 128 to encode the following 12 frequencies: (260, 262, 264, 266, 276, 279, 281, 283, 285, 287, 289, 291)
GSM480: use Range 128 to encode the following 12 frequencies: (307, 309, 311, 313, 323, 326, 328, 330, 332, 334, 336, 338)
GSM900: use bit map 0 to allocates the following 12 frequencies: (14, 18, 22, 24, 60, 66, 73, 74, 75, 76,108, 114)
GSM1800: Use Range 1024 to allocate the following 12 frequencies: (749, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
PCS1900: Use Range 1024 to allocate the following 12 frequencies: (649, 658, 661, 664, 671, 679, 682, 791, 798, 729, 732, 744)
GSM710, GSM 750 and T-GSM 810: Use 128 range to allocates the following 12 frequencies: (451, 455, 459, 461, 497, 498, 500, 501, 502, 503,506, 508)
GSM850: Use 128 range to allocates the following 12 frequencies: (141, 145, 149, 151, 187, 193, 200, 201, 202, 203, 235, 241)
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel
- Mode
speech half rate version 1
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with half rate speech version 1 and in hopping mode on cell B.
For M = 10:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 1 and hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 263
GSM480: 310
GSM900: 20
GSM1800: 747
PCS1900: 647
GSM710: 457
GSM750: 457
T-GSM810: 457
GSM850: 147
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- ARFCN
Chosen arbitrarily from the CA
Synchronisation Indication IE is not included.
Mode of the first channel.
- Mode
speech full rate version 3
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and non-hopping mode on cell A.
For M = 11:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
GSM450: 274
GSM480: 321
GSM900: 40
GSM1800: 764
PCS1900: 664
GSM710: 477
GSM750: 477
T-GSM810: 477
GSM850: 167
Channel Description
- Channel Type
TCH/H + ACCHs
- TDMA offset
Chosen arbitrarily
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set ( 0, 1 to N-1 ), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set
(1,2,..63)
Frequency List after time
- Frequency List
GSM450: use Range 128 to encode the following 12 frequencies: (260, 262, 264, 266, 276, 279, 281, 283, 285, 287, 289, 291)
GSM480: use Range 128 to encode the following 12 frequencies: (307, 309, 311, 313, 323, 326, 328, 330, 332, 334, 336, 338)
GSM900: use bit map 0 to allocates the following 12 frequencies: (14, 18, 22, 24, 60, 66, 73, 74, 75, 76,108, 114)
GSM1800: Use Range 1024 to allocate the following 12 frequencies: (749, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
PCS1900: Use Range 1024 to allocate the following 12 frequencies: (649, 658, 661, 664, 671, 679, 682, 791, 798, 729, 732, 744)
GSM710, GSM 750 and T-GSM 810: Use 128 range to allocates the following 12 frequencies: (451, 455, 459, 461, 497, 498, 500, 501, 502, 503,506, 508)
GSM850: Use 128 range to allocates the following 12 frequencies: (141, 145, 149, 151, 187, 193, 200, 201, 202, 203, 235, 241)
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
Mode of the first channel
- Mode
speech half rate version 3
Starting Time
Indicates the frame number of cell B. that will occur approximately 1,1 seconds ( 238 frames have elapsed ) after the HANDOVER COMMAND is sent by cell A.
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with half rate speech version 3 and in hopping mode on cell B.
For M = 12:
Step 0: The MS and SS are using a half rate TCH with half rate speech version 3 and in hopping mode on cell B.
HANDOVER COMMAND
same as for M = 4 except:
Channel Description
- Channel Type
TCH/H + ACCHs
PHYSICAL INFORMATION
same as for M = 4
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with half rate speech version 3 and in non-hopping mode on cell A.
For M = 13:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
same as for M = 5
PHYSICAL INFORMATION
same as for M = 5
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 1 and in non-hopping mode on cell B.
For M = 14:
Step 0: The MS and SS are using a full rate TCH with speech full rate version 1 and in non-hopping mode on cell B.
HANDOVER COMMAND
same as for M = 6 except:
Channel Description
- Channel Type
TCH/H + ACCHs
PHYSICAL INFORMATION
same as for M = 6
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with speech half rate version 3 and in non-hopping mode on cell A.
For M = 15:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
same as for M = 7
PHYSICAL INFORMATION
same as for M = 7
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with full rate speech version 2 and in hopping mode on cell B.
For M = 16:
Step 0: The MS and SS are using a full rate TCH with full rate speech version 2 and in hopping mode on cell B.
HANDOVER COMMAND
same as for M = 8 except:
Channel Description
- Channel Type
TCH/H + ACCHs
PHYSICAL INFORMATION
same as for M = 8
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with speech half rate version 3 and in hopping mode on cell A.
For M = 17:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 3 and in hopping mode on cell A.
HANDOVER COMMAND
same as for M = 9
PHYSICAL INFORMATION
same as for M = 9
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with speech half rate version 1 and in hopping mode on cell B.
For M = 18:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 1 and in hopping mode on cell B.
HANDOVER COMMAND
same as for M = 10 except:
Channel Description
- Channel Type
TCH/H + ACCHs
PHYSICAL INFORMATION
same as for M = 10
Step 6: x = 750
Step 7: The MS and SS are using a half rate TCH with speech half rate version 3 and in non-hopping mode on cell A.
For M = 19:
Step 0: The MS and SS are using a half rate TCH with speech half rate version 3 and in non-hopping mode on cell A.
HANDOVER COMMAND
same as for M = 1
PHYSICAL INFORMATION
same as for M = 1
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH with speech full rate version 3 and in non-hopping mode on cell B.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.6 Structured procedures / emergency call
|
NOTE: this test is derived from subclause 26.15.5 - Structured procedures / emergency call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.6.1 Conformance requirement
|
1) The MS in the "idle, updated" state, after a successful location update, the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct CKSN and TMSI , with CM Service Type "emergency call establishment".
3) Authentication and cipher mode setting shall be performed successfully.
4) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
5) The AMR mobile station shall accept channel assignment to an AMR full-rate channel and if supported an AMR half rate channel depending what the network signals to the mobile and also select the correct codec mode. The call shall be set up using the AMR codec.
6) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH/AF or TCH/AH shall be through connected in both directions if an appropriate channel is available.
7) The call shall be cleared correctly.
References:
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.3.1, 3.4.6, 9.1.2 and 9.1.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.6.2 Test purpose
|
1) To verify that an MS supporting speech in the MM state "idle, updated", when made to call the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message specifying the correct CKSN and TMSI, with CM Service Type "emergency call establishment".
3) To verify that authentication and cipher mode setting are performed successfully.
4) To verify that after cipher mode setting acceptance by the SS, the MS sends an EMERGENCY SETUP message.
5) To verify that the AMR mobile station shall accept channel assignment to a TCH/AF and if it supports half rate, also to a TCH/A depending what the network signals to the mobile and also select the correct codec mode. The call shall be set up using the AMR codec.
6) To verify that subsequently the MS has through connected the TCH in both directions.
7) To verify the call is cleared correctly.
26.16.6.3 Method of Test
Initial Conditions
SS: 1 cell default parameters.
MS: The MS is in the MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen Final State of the MS
The MS is in the MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Test Procedure
The MS is made to initiate an emergency call. The call is established with late assignment. Having reached the active state, the call is cleared by the SS. This procedure is repeated so that the assignment is made with full rate and half rate speech versions as supported by the MS.
Maximum Duration of Test
3 minutes.
Expected Sequence
This test is repeated for K=1, and where the MS supports half rate version 3 K=2.
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered
2
MS->SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
EMERGENCY SETUP
The MS indicates it which speech it supports.
11
SS->MS
CALL PROCEEDING
12
SS->MS
ALERTING
13
SS->MS
ASSIGNMENT COMMAND
See specific message contents.
14
MS->SS
ASSIGNMENT COMPLETE
15
SS->MS
CONNECT
16
MS->SS
CONNECT ACK
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
DISCONNECT
19
MS->SS
RELEASE
20
SS->MS
RELEASE COMPLETE
21
SS->MS
CHANNEL RELEASE
Specific Message Contents:
K = 1
Assignment Command
Information Element
value/remark
Channel description
TCH/AF
Channel mode
- Mode
Speech full rate version 3
K = 2
This step is applicable only if the MS supports half rate version 3.
Assignment Command
Information Element
value/remark
Channel description
TCH/AH
Channel mode
- Mode
Speech half rate version 3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.7 AMR Signalling / Directed Retry / Mobile Originated Call
|
NOTE: This test is derived from the one defined in subclause 26.12.6 and entitled "EFR Signalling / Directed Retry / Mobile Originated Call".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.7.1 Conformance requirements
|
The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (no frequency hopping) to TCH/AMR with frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "mobile originating call proceeding" state shall, upon receipt of a CONNECT message, attach the AMR speech connection to the radio path and return a CONNECT ACKNOWLEDGE message to the SS.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.4 and 9.1.15,
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.6.
3GPP TS 04.13, subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.7.2 Test purpose
|
To test that, when the MS is ordered to perform a non-synchronized handover after the CALL PROCEED message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance information element in the PHYSICAL INFORMATION message into account. To test that the MS activates the new channel correctly and transmits the HANDOVER COMPLETE message without undue delay. To test that the call control entity of the Mobile Station in the "mobile originating call proceeding" state, upon receipt of a CONNECT message, attaches the AMR speech connection to the radio path and returns a CONNECT ACKNOWLEDGE message to the SS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.7.3 Method of test
|
Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
NCC_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = 3.
BS colour code, BCC = 0.
Band
Cell A
Cell B
Both Cells
BCCH ARFCN
Cell Allocation
BCCH ARFCN
Cell Allocation
Format
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291
274
260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291
Range 128
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338
321
307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338
Range 128
GSM 710
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 750
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241
167
141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241
Range 128
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114
40
14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114
Bitmap 0
DCS 1 800
747
734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844
764
739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
Range 512
PCS 1 900
647
634, 641, 647, 654, 659, 662, 666, 667, 673, 675, 679, 682, 691, 698, 729, 732, 744
664
639, 643, 646, 649, 656, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Range 512
The time base of Cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
A non-combined SDCCH is used.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
- Way to indicate mobile originated alerting.
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
The MS is made to initiate a speech call on Cell A. After the SS has sent the CALL PROCEEDING message the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B. The MS shall then begin to send access bursts on the new DCCH (and optionally on the SACCH) to cell B. The SS observes the access bursts and after receiving n (n being arbitrarily chosen between values according to table 26.6‑2 of subclause 26.6.5) access bursts, the SS sends one PHYSICAL INFORMATION message with an arbitrarily chosen Timing Advance. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message before x ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS. After the successful handover procedure the SS sends the ALERTING message. The correct alerting indication shall be given to the user (only applicable if the MS supports this feature). The SS sends the CONNECT message indicating that the call has been answered. The AMR speech channel shall be through connected in both directions. The MS shall send then the CONNECT ACKNOWLEDGE message as the response on the CONNECT message. Having reached the active state, the call is cleared by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13. The value of "x" depends upon the target channel and is specified in the specific message contents section.
Maximum Duration of Test
1 minute, including 30 s for any necessary operator actions.
Expected Sequence
Step
Direction
Message
Comments
1
--------
--------
A MO call is initiated on cell A.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
3
SS -> MS
IMMEDIATE ASSIGNMENT
See specific message contents.
4
MS -> SS
CM SERVICE REQUEST
CM Service Type = Mobile Originating Call Establishment.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
MS -> SS
SETUP
AMR speech
11
SS -> MS
CALL PROCEEDING
12
SS -> MS
HANDOVER COMMAND
See specific message contents.
13
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND.
14
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
15
MS -> SS
SABM
Sent without information field.
16
SS -> MS
UA
17
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step 14.
18
SS -> MS
ALERTING
19
MS
An alerting indication is given as described in the PIXIT.
20
SS -> MS
CONNECT
21
MS -> SS
CONNECT ACKNOWLEDGE
22
MS
The AMR speech channel is through connected in both directions.
23
SS -> MS
DISCONNECT
24
MS -> SS
RELEASE
25
SS -> MS
RELEASE COMPLETE
26
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
As default message contents.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
Single RF Channel.
- ARFCN
Chosen arbitrarily from the Cell Allocation of Cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily.
- Timeslot number
Chosen arbitrarily but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Synchronization Indication IE is not included
Frequency list after time
- Frequency List
Allocate frequencies as per the table below
Channel Mode IE
Speech (multi rate version 1).
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
HANDOVER COMMAND
Band
Frequency Short List
BCCH Carrier Number
Format
ARFCNs
ARFCN
GSM 450
Range 128
260, 262, 264, 266, 268, 270, 272, 276, 279, 281, 283, 285, 287, 289, 291
274
GSM 480
Range 128
307, 309, 311, 313, 315, 317, 319, 323, 326, 328, 330, 332, 334, 336, 338
321
GSM 710
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
GSM 750
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
T-GSM 810
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
GSM 850
Range 128
141, 145, 149, 151, 157, 158, 165, 187, 193, 200, 201, 202, 203, 235, 241
167
GSM 900
Range 128
14, 18, 22, 24, 30, 31, 38, 60, 66, 73, 74, 75, 76, 108, 114
40
DCS 1 800
Range 128
746, 779
764
PCS 1 900
Range 128
646, 679
664
Step 17: "x" = 500.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.8 AMR Signalling / Directed Retry / Mobile Terminated Call
|
NOTE: This test is derived from the one defined in subclause 26.12.7 and entitled "EFR Signalling / Directed Retry / Mobile Terminated Call".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.8.1 Conformance requirements
|
The MS shall correctly apply the Directed Retry procedure from SDCCH/8 with frequency hopping to TCH/AMR with frequency hopping and starting time in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "call delivered" state shall, if the MS supports immediate connect, continue the call establishment by through-connecting the AMR traffic channel in both directions, or if the MS does not support immediate connect, send an ALERTING message. The MS indicates acceptance of a MT call by sending CONNECT.
The mobile station shall attach the user connection at latest when sending the CONNECT message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.4 and 9.1.15,
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.5, 5.2.2.6 and 5.2.2.9.
3GPP TS 04.13, subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.8.2 Test purpose
|
To test that when the MS is ordered to perform a non-synchronized handover after the CALL CONFIRM message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance information element in the PHYSICAL INFORMATION message into account. To test that the MS activates the new channel correctly and transmits the HANDOVER COMPLETE message without undue delay. To test that the call control entity of the Mobile Station in the "call delivered" state, if the MS supports immediate connect, continues the call establishment by through-connecting the AMR traffic channel in both directions, or if the MS does not support immediate connect, sends an ALERTING message. To test that the MS indicates acceptance of a MT call by sending CONNECT.
To test that the mobile station attaches the user connection at latest when sending the CONNECT message, except if there is no compatible radio resource available at this time. To test that in this case the attachment is delayed until such a resource becomes available.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.8.3 Method of test
|
Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation =See the table below. PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
NCC_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = 3.
BS colour code, BCC = 0.
Band
Cell A
Cell B
Both Cells
BCCH ARFCN
Cell Allocation
BCCH ARFCN
Cell Allocation
Format
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291
274
260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291
Range 128
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338
321
307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338
Range 128
GSM 710
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 750
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241
167
141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241
Range 128
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114
40
14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114
Bitmap 0
DCS 1 800
747
734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844
764
739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
Range 512
PCS 1 900
647
634, 641, 647, 654, 659, 662, 666, 667, 673, 675, 679, 682, 691, 698, 729, 732, 744
664
639, 643, 646, 649, 656, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Range 512
The time base of Cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
A non-combined SDCCH is used.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
The MS is paged on Cell A. The MS responds to the PAGING REQUEST message and establishes a mobile terminated speech call on Cell A. If the MS supports immediate connect, it continues the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, it sends an ALERTING message. The MS indicates acceptance of a MT call by sending CONNECT.
After the MS has sent the CALL CONFIRMED message (if the MS supports immediate connect then the MS sends the CONNECT message after the CALL CONFIRMED message on the old channel) the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B. The MS shall then begin to send access bursts on the new DCCH (and optionally on the SACCH) to cell B. The SS observes the access bursts and after receiving n (n being arbitrarily chosen between values according to table 26.6‑2 of subclause 26.6.5) access bursts, the SS sends one PHYSICAL INFORMATION message with an arbitrarily chosen Timing Advance. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message before x ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS. After the successful handover procedure the MS sends the ALERTING message (if the MS runs the immediate connect procedure then the MS does not send an ALERTING message). The correct alerting indication shall be given to the user (only applicable if the MS supports the feature or if the MS is not using the immediate connect procedure). After the MS sent the CONNECT message the AMR speech channel shall be through connected in both directions. The SS sends then the CONNECT ACKNOWLEDGE message as the response on the CONNECT message. Having reached the active state, the call is cleared by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13. The value of "x" depends upon the target channel and is specified in the specific message contents section.
Maximum Duration of Test
1 minute, including 30 s for any necessary operator actions.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel on cell A.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
See specific message contents.
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
SS -> MS
SETUP
AMR speech.
11
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A12
MS -> SS
CONNECT
sent on the old channel
A13
SS -> MS
HANDOVER COMMAND
See specific message contents.
A14
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND. The first HANDOVER ACCESS message shall be transmitted in the indicated frame (unless the indicated frame is not used by that channel, in which case the next frame used by that channel shall be used).
A15
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
A16
MS -> SS
SABM
Sent without information field.
A17
SS -> MS
UA
A18
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step A15.
B12
SS -> MS
HANDOVER COMMAND
See specific message contents.
B13
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND. The first HANDOVER ACCESS message shall be transmitted in the indicated frame (unless the indicated frame is not used by that channel, in which case the next frame used by that channel shall be used).
B14
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
B15
MS -> SS
SABM
Sent without information field.
B16
SS -> MS
UA
B17
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step B14.
B18
MS -> SS
ALERTING
B19
MS
Gives an alerting indication as defined in a PIXIT statement is given by the MS
B20
MS
The MS is made to accept the call in the way described in a PIXIT statement
B21
MS -> SS
CONNECT
22
MS
The TCH/AMR channel shall be through connected in both directions.
23
SS -> MS
CONNECT ACKNOWLEDGE
24
SS -> MS
DISCONNECT
25
MS -> SS
RELEASE
26
SS -> MS
RELEASE COMPLETE
27
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
L2 pseudo length
14 octets (11 + contents of the MA).
Channel Description
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
- Length
3 octets.
- Contents
Indicates only three frequencies, as per the table below.
IMMEDIATE ASSIGNMENT
Band
Mobile Allocation
GSM 450
281, 283, 285
GSM 480
328, 330, 332
GSM 710
500, 501, 502
GSM 750
500, 501, 502
T-GSM 810
500, 501, 502
GSM 850
200, 201, 202
GSM 900
73, 74, 75
DCS 1 800
773, 775, 779
PCS 1 900
673, 675, 679
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily.
- Timeslot number
Chosen arbitrarily, but not Zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Frequency List after time
- Frequency List
Allocate frequencies as per the table below.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Mode of First Channel
Speech (multi rate version 1).
Starting Time
Indicates the frame number of cell B that will occur approximately 1,1 seconds (238 frames have elapsed) after the HANDOVER COMMAND is sent by cell A.
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
HANDOVER COMMAND
Band
BCCH Carrier Number
Cell Channel Description
ARFCN
Format
ARFCNs
GSM 450
274
Range 128
260, 262, 264, 266, 276, 279, 281, 283, 285, 287, 289, 291
GSM 480
321
Range 128
307, 309, 311, 313, 323, 326, 328, 330, 332, 334, 336, 338
GSM 710
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
GSM 750
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
T-GSM 810
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
GSM 850
167
Range 128
141, 145, 149, 151, 187, 193, 200, 201, 202, 203, 235, 241
GSM 900
40
Bitmap 0
14, 18, 22, 24, 60, 66, 73, 74, 75, 76,108, 114
DCS 1 800
764
Range 1024
749, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
PCS 1 900
664
Range 1024
649, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Step A18 / B17: "x" =500.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9 AMR RATSCCH Protocol
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.1 AMR Configuration Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.1.1 Conformance requirements
|
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference
3GPP TS 05.09 sub-clauses: 3.2.2.3.1, 3.2.2.3.5
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.