hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.1.2 Test purpose
|
This test will verify that the MS is able to handle a properly formatted AMR_CONFIG_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
This sequence is performed for execution counter, k = 1, 2.
When k = 1, DTX is not used:
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send a properly formatted AMR_CONFIG_REQ message during the call at a programmable time.
6) The MS answers with a ACK_OK message within 3 speech frames
7) The network initiates the call release.
When k = 2, DTX is used:
1) In the serving cell, the DTX indicator is set to "MS shall use discontinuous transmission".
2) User initiates a Mobile Originated call.
3) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
4) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
5) The call is maintained during a programmable time without variation of RxLev /RxQual.
6) The SS shall send a properly formatted AMR_CONFIG_REQ message during the call at a programmable time.
7) The MS answers with a ACK_OK message within 3 speech frames.
8) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
When k=1:
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
When k=2:
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
Using DTX mode
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate of half rate version 3
AMR_CONFIG_REQ
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.2 AMR Configuration Change (abnormal)
|
26.16.9.2.1 Conformance requirements
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference:
3GPP TS 05.09 sub-clauses: 3.2.2.3.2, 3.2.2.3.5
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.2.2 Test purpose
|
This test will verify that the MS is able to handle an improperly formatted AMR_CONFIG_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an AMR_CONFIG_REQ message, with an incorrect CRC, during the call at a programmable time.
6) The MS answers with a ACK_ERR message within 3 speech frames
7) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->22
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
AMR_CONFIG_REQ
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.3 Codec Mode Phase Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.3.1 Conformance requirements
|
The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference:
3GPP TS 05.09 sub-clauses: 3.2.2.3.1, 3.2.2.3.4
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.3.2 Test purpose
|
This test will verify that the MS can correctly handle a properly formatted CMI_PHASE_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send the CMI_PHASE_REQ message during the call at a programmable time. The CMI_PHASE_REQ shall be sent either in place of a "CMI" speech frame, or in place of a "CMC" speech frame, to cover both kinds of changes.
6) The MS answers with a ACK_OK message within 3 speech frames.
7) The downlink CMI phase is changed (or not) according to the CMI_PHASE_REQ message starting with speech frame N+12.
8) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
CMI_PHASE_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
CMI_PHASE_REQ
Information Element
value/remarks
CMIP
1 (default)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.4 Codec Mode Phase Change (abnormal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.4.1 Conformance requirements
|
The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference
3GPP TS 05.09 sub-clauses: 3.2.2.3.2, 3.2.2.3.4
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.4.2 Test purpose
|
This test will verify that the MS can correctly handle an improperly formatted CMI_PHASE_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send the CMI_PHASE_REQ message, with an incorrect CRC, during the call at a programmable time. The CMI_PHASE_REQ shall be sent either in place of a "CMI" speech frame, or in place of a "CMC" speech frame, to cover both kinds of changes.
6) The MS answers with a ACK_ERR message within 3 speech frames.
7) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
CMI_PHASE_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
CMI_PHASE_REQ
Information Element
value/remarks
CMIP
1 (default)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.5 Threshold Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.5.1 Conformance requirements
|
The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference:
3GPP TS 05.09 sub-clauses: 3.2.2.3.1, 3.2.2.3.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.5.2 Test purpose
|
This test will verify that an RATSCCH capable MS is able to handle a properly formatted THRESH_REQ message
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.5.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send a properly formatted THRESH_REQ message during the call at a programmable time.
6) The MS answers with a ACK_OK message within 3 speech frames
7) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
THRESH_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
Multi-Rate configuration
2 codec modes specified
THRESH_REQ
Information Element
value/remarks
HYST3
Not defined (set to all 1s)
THRESH3
Not defined (set to all 1s)
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.6 Threshold Change (abnormal)
|
26.16.9.6.1 Conformance requirements
The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference:
3GPP TS 05.09 sub-clauses: 3.2.2.3.2, 3.2.2.3.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.6.2 Test purpose
|
This test will verify that an RATSCCH capable MS is able to handle an improperly formatted THRESH_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.6.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an improperly formatted THRESH_REQ message, with an incorrect CRC, during the call at a programmable time.
6) The MS answers with a ACK_ERR message within 3 speech frames
7) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
THRESH_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
THRESH_REQ
Information Element
value/remarks
HYST3
Not defined (set to all 1s)
THRESH3
Not defined (set to all 1s)
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.7 Unknown RATSCCH REQ Message
|
26.16.9.7.1 Conformance requirements
The ACK_UNKNOWN message serves as an acknowledgement that a RATSCCH REQ message has been detected and correctly decoded, but was unknown to the Addressee.
Reference:
3GPP TS 05.09 sub-clause: 3.2.2.3.3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.7.2 Test purpose
|
This test will verify that the MS can correctly handle an unknown RATSCCH REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.7.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an unknown RATSCCH_REQ message, with message content as all zeros, during the call at a programmable time.
6) The MS answers with a ACK_UNKNOWN message within 3 speech frames
7) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
Unknown RATSCCH message
Message contents all 0’s
19
MS->SS
ACK_UNKNOWN
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
RATSCCH_REQ
Information Element
value/remarks
all bits
0
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.8 Ignore subsequent REQ prior to expiry of REQ_Activation counter
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.8.1 Conformance requirements
|
If another REQ message is received by the MS before the REQ_Activation counter has elapsed, the MS shall ignore the message.
Reference:
3GPP TS 45.009 sub-clause: 3.2.2.2
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.8.2 Test purpose
|
This test will verify that the MS ignores a REQ message which is received before the REQ_Activation counter has elapsed. The test will verify that both the following conditions are satisfied:
- the MS ignores a subsequent REQ message received after it has sent the ACK_OK but before the REQ_Activation counter has elapsed.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.8.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an AMR_CONFIG_REQ message during the call at a programmable time.
6) The MS answers the AMR_CONFIG_REQ with an ACK_OK message within 3 speech frames of the AMR_CONFIG_REQ.
7) The SS shall send a second AMR_CONFIG_REQ message within 11 speech frames of sending the first AMR_CONFIG_REQ message .
8) The SS shall verify that the codec mode used by the MS after the REQ_Activation counter has elapsed is consistent with the first AMR_CONFIG_REQ message, and not the second AMR_CONFIG_REQ message.
9) The SS initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
AMR_CONFIG_REQ
See specific message contents. To be sent to MS within 11 speech frames of having sent the first message in step 18.
21
MS
Verify that the codec mode used by the MS is that specified in step 18.
22
SS->MS
Disconnect
23
MS->SS
Release
24
SS->MS
Release Complete
25
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3.
AMR_CONFIG_REQ
In step 18:
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
In step 20:
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
1 codec mode – different to any codec mode specified in the ACS in step 18.
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
Not defined (set to all 1s)
THRESH1
Not defined (set to all 1s)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.9 Initiation of Transaction with ACK_ERR or ACK_UNKNOWN
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.9.1 Conformance requirements
|
If at either side an ACK_ERR or ACK_UNKNOWN is received although no corresponding REQ has been sent before, the ACK message shall be ignored.
Reference:
3GPP TS 45.009 sub-clause: 3.2.2.2
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.9.2 Test purpose
|
This test will verify that the MS ignores any ACK_ERR or ACK_UNKNOWN which is received without a corresponding REQ having been sent.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.9.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an ACK_ERR message during the call at a programmable time.
6) The SS verifies that no message is received from the MS on the RATSCCH within 12 speech frames.
7) The SS shall send an ACK_UNKNOWN message during the call at a programmable time.
8) The SS verifies that no message is received from the MS on the RATSCCH within 12 speech frames.
9) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents for codec modes.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
ACK_ERR
19
MS
Wait at least 12 speech frames to ensure that no message is received from the MS.
20
SS->MS
ACK_UNKNOWN
21
MS
Wait at least 12 speech frames to ensure that no message is received from the MS.
22
SS->MS
Disconnect
23
MS->SS
Release
24
SS->MS
Release Complete
25
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.10 Inversion of the Phase of the CMR/CMI
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.10.1 Conformance requirements
|
The phase of the Codec Mode Indication in the downlink can be changed during a call by using a CMI_PHASE_REQ message sent on the RATSCCH.
The CMI_PHASE_REQ message may be sent by the BTS during a call to change the phase of the Codec Mode Indication in the downlink without interruption of the speech transmission.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee.
References:
3GPP TS 05.09 clauses 3.2.1.3 and 3.2.2.3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.10.2 Test purpose
|
This test shall verify that the MS is able to change the phase of the Codec Mode Indication in the downlink using the RATSCCH protocol.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.10.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The network shall indicate Codec Mode Command = 0 and Codec Mode Indication = 1.
5) The SS sends a series of CMI_PHASE_REQ messages during the call to change the phase of the Codec Mode Indication in the downlink.
6) The MS responds to each CMI_PHASE_REQ message with an ACK_OK message on the RATSCCH.
7) The SS shall ensure that the phase request has been handled correctly by checking the Uplink CMI = 0 for 20 speech frames following the receipt of the ACK_OK.
8) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS->MS
Setup
AMR speech
11
MS->SS
Call Proceeding
12
MS->SS
Alerting
13
SS->MS
Assignment Command
Multirate Configuration for 2 codec modes
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
CMI_PHASE_REQ
See specific message contents
19
MS->SS
ACK_OK
20
MS
Wait 20 speech frames, then check that UL CMI = 0
21
SS->MS
CMI_PHASE_REQ
See specific message contents
22
MS->SS
ACK_OK
23
MS
Wait 20 speech frames, then check that UL CMI = 0
24
SS->MS
CMI_PHASE_REQ
See specific message contents
25
MS->SS
ACK_OK
26
MS
Wait 20 speech frames, then check that UL CMI = 0
27
SS->MS
CMI_PHASE_REQ
See specific message contents
28
MS->SS
ACK_OK
29
MS
Wait 20 speech frames, then check that UL CMI = 0
30
SS->MS
Disconnect
31
MS->SS
Release
32
SS->MS
Release Complete
33
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3.
In step 18:
CMI_PHASE_REQ
Information Element
value/remark
CMIP
0: CMI transmitted in even speech frames
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Command.
In step 21:
CMI_PHASE_REQ
Information Element
value/remark
CMIP
1: CMI transmitted in odd speech frames (back to default)
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Command.
In step 24:
CMI_PHASE_REQ
Information Element
value/remark
CMIP
0: CMI transmitted in even speech frames
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Indication.
In step 27:
CMI_PHASE_REQ
Information Element
value/remark
CMIP
1: CMI transmitted in odd speech frames (back to default)
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Indication.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.11 Change of Active Codec Set
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.11.1 Conformance requirements
|
AMR codec mode adaptation is done within a set of 4 codec modes. The codec mode set (Active Codec Set) to be used by the BSS and the MS is defined during call setup and/or handover by layer 3 signalling. The ACS can be changed during a call using an AMR_CONFIG_REQ message sent on the RATSCCH.
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee.
If the ACS consists of four modes, then the complete set of thresholds/hysteresis can not be sent with this message. In that case, all THRESHj and HYSTj fields are reserved for future use and shall be set to "1". Similar, if the BTS has no threshold and hysteresis parameters for the given configuration, then all THRESHj and HYSTj field bits shall be set to "1" to indicate that they are undefined. The THRESH_REQ message shall be used to transmit these parameters at a later point in time. As long as the MS has no defined threshold and hysteresis parameters it shall use the Initial Codec Mode for the Codec Mode Request.
References:
3GPP TS 05.09 clauses 3.2.2.3.5 and 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.11.2 Test purpose
|
This test shall verify that the MS is able to change its Active Codec Set using the RATSCCH protocol, with change of thresholds, and with non-specification of thresholds.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.11.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
PIXIT statements:
-.
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Full Rate and Half Rate (Version 3).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The SS uses the codec with the highest bit-rate in the current ACS for the Codec Mode Indication, and that with the lowest bit-rate for the Codec Mode Command.
5) The SS sends an AMR_CONFIG_REQ message during the call to reconfigure the Multirate settings.
6) The MS responds to each AMR_CONFIG_REQ message with an ACK_OK message on the RATSCCH.
7) The SS shall ensure that the change occurs correctly for downlink (12 speech frames after AMR_CONFIG_REQ message was sent), and for uplink (12 speech frames after ACK_OK was received) by checking parity of received speech frames, and correct implementation of Uplink Codec mode Request.
8) The SS shall ensure that each of the codecs in the ACS have been implimented correctly by setting the CMC to each of the applicable modes, and ensuring that the UL frames with each CMI are received without parity error. The SS shall then set the CMI and CMC to the codec with highest and lowest bit rates respectively.
9) Steps 4 to 8 shall be repeated for differing AMR_CONFIG_REQ parameters and sending conditions.
10) The network initiates the call release.
This test is repeated for M=1, and where the MS supports half rate version 3 M=2.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
AMR speech
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
Multirate Configuration for 2 codec modes
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
See specific message contents.
19
MS->SS
ACK_OK
20
MS
Check that ACS changes have been implemented correctly. Expected CMR = 0.
21
SS->MS
AMR_CONFIG_REQ
See specific message contents.
22
MS->SS
ACK_OK
23
MS
Check that ACS changes have been implemented correctly. Expected CMR = 0 or 1.
24
SS->MS
AMR_CONFIG_REQ
See specific message contents.
25
MS->SS
ACK_OK
26
MS
Check that ACS changes have been implemented correctly. Expected CMR = 0, 1 or 2.
27
SS->MS
AMR_CONFIG_REQ
See specific message contents.
28
MS->SS
ACK_OK
29
MS
Check that ACS changes have been implemented correctly. Expected CMR = 0, 1, 2 or 3.
30
SS->MS
AMR_CONFIG_REQ
See specific message contents.
31
MS->SS
ACK_OK
32
MS
Check that ACS changes have been implemented correctly. Expected CMR = 2 (special case where CMR = ICM).
33
SS->MS
Disconnect
34
MS->SS
Release
35
SS->MS
Release Complete
36
SS->MS
Channel Release
Specific Message Contents
In all cases, the Active Codec Set field of the AMR_CONFIG_REQ messages should be programmed to ensure that the codec rate changes when the new configuration takes effect.
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
M=1: TCH/F
M=2: TCH/H
Mode of the first channel
- Mode
Full rate or half rate version 3.
Multi-Rate configuration
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
In step 18:
AMR_CONFIG_REQ
Information Element
value/remark
ICM
CODEC_MODE_1
ACS
1 codec mode (different from that in Assignment Command)
HYST2
n/a – set to all 1’s
THRESH2
n/a – set to all 1’s
HYST1
n/a – set to all 1’s
THRESH1
n/a – set to all 1’s
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Command.
In step 21:
AMR_CONFIG_REQ
Information Element
value/remark
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
n/a – set to all 1’s
THRESH2
n/a – set to all 1’s
HYST1
2 dB
THRESH1
12.5 dB
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Command.
In step 24:
AMR_CONFIG_REQ
Information Element
value/remark
ICM
CODEC_MODE_2
ACS
3 codec modes
HYST2
2 dB
THRESH2
13 dB
HYST1
2 dB
THRESH1
7 dB
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Indication.
In step 27:
AMR_CONFIG_REQ
Information Element
value/remark
ICM
CODEC_MODE_3
ACS
4 codec modes
HYSTc
2 dB
THRESH3
18 dB
THRESH2
12 dB
THRESH1
6.5 dB
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Indication.
In step 30:
AMR_CONFIG_REQ
Information Element
value/remark
ICM
CODEC_MODE_3
ACS
4 codec modes
HYST2
Undefined – set to all 1’s
THRESH2
Undefined – set to all 1’s
HYST1
Undefined – set to all 1’s
THRESH1
Undefined – set to all 1’s
This message should be sent in a RATSCCH frame where the RATSCCH frame (or RATSCCH_DATA part for AHS) replaces a speech frame which would have carried a Codec Mode Command.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.9.12 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10 AMR signalling/ test of the channel mode modify procedure
|
NOTE: This test is derived from the test in sub-clause 26.12.1 entitled "EFR signalling / Test of the channel mode modify procedure ".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.1 AMR signalling/ test of the channel mode modify procedure/ full rate
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.1.1 Conformance requirement
|
The MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6.1.1 and 3.4.6.1.2
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.1.2 Test purpose
|
To verify that the MS with a TCH/F allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.1.3 Method of test
|
Initial Conditions
System Simulator: 1 cell, default parameters.
Mobile Station: The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
-.
PIXIT statements:
-.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test procedure
A Mobile Terminated call is initiated, however following the CHANNEL REQUEST received from the Mobile Station, the SS sends an IMMEDIATE ASSIGNMENT to the MS commanding it to go to a TCH/F. This sets the Channel Mode automatically to "Signalling Only".
The SS then sends a series of CHANNEL MODE MODIFY messages to the MS. Each time it is checked that the MS responds with a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the channel mode that has been specified in the CHANNEL MODE MODIFY message
Maximum Duration of Test
30 seconds.
Expected Sequence
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on correct paging subchannel
2
MS->SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging"
3
SS->MS
IMMEDIATE ASSIGNMENT
Assignment to a non hopping TCH/F signalling only
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
CHANNEL MODE MODIFY
11
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/F, Channel mode = speech full or half rate version 3
12
SS->MS
CHANNEL MODE MODIFY
13
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/F, Channel mode = speech full or half rate version 3
14
SS->MS
CHANNEL MODE MODIFY
15
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/F, Channel mode = speech full or half rate version 3
16
SS->MS
CHANNEL MODE MODIFY
17
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/F, Channel mode = speech full or half rate version 3
18
SS->MS
CHANNEL RELEASE
Specific Message Contents
In steps 10 – 16:
CHANNEL MODE MODIFY
Information Element
value/remark
Channel description
in steps 10, 12, 14, 16: same as for step 3
Channel mode
Mode
speech full or half rate version 3
Multi-Rate configuration
in steps 10: change of MR configuration, no initial codec mode
in steps 12: change of MR configuration, initial codec mode specified
in steps 14: change of MR thresholds, no initial codec mode
in steps 16: initial codec mode specified
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.2 AMR signalling/ test of the channel mode modify procedure/ half rate
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.2.1 Conformance requirement
|
The MS with a TCH/H allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6.1.1 and 3.4.6.1.2
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.2.2 Test purpose
|
To verify that the MS with a TCH/H allocated acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the new mode and by switching to this mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.10.2.3 Method of test
|
Initial Conditions
System Simulator: 1 cell, default parameters.
Mobile Station: The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
-.
PIXIT statements:
-.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test procedure
A Mobile Terminated call is initiated, however following the CHANNEL REQUEST received from the Mobile Station, the SS sends an IMMEDIATE ASSIGNMENT to the MS commanding it to go to a TCH/H. This sets the Channel Mode automatically to "Signalling Only".
The SS then sends a series of CHANNEL MODE MODIFY messages to the MS. Each time it is checked that the MS responds with a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying the channel mode that has been specified in the CHANNEL MODE MODIFY message
Maximum Duration of Test
30 seconds.
Expected Sequence
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on correct paging subchannel
2
MS->SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging"
3
SS->MS
IMMEDIATE ASSIGNMENT
Assignment to a non hopping TCH/H signalling only
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
CHANNEL MODE MODIFY
11
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/H, Channel mode = speech full or half rate version 3
12
SS->MS
CHANNEL MODE MODIFY
13
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/H, Channel mode = speech full or half rate version 3
14
SS->MS
CHANNEL MODE MODIFY
15
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/H, Channel mode = speech full or half rate version 3
16
SS->MS
CHANNEL MODE MODIFY
17
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
Verify that Channel description = TCH/H, Channel mode = speech full or half rate version 3
18
SS->MS
CHANNEL RELEASE
Specific Message Contents
In steps 10 – 16:
CHANNEL MODE MODIFY
Information Element
value/remark
Channel description
in steps 10, 12, 14, 16: same as for step 3
Channel mode
Mode
speech full or half rate version 3
Multi-Rate configuration
in steps 10: change of MR configuration, no initial codec mode
in steps 12: change of MR configuration, initial codec mode specified
in steps 14: change of MR thresholds, no initial codec mode
in steps 16: initial codec mode specified
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.11 Handover / layer 1 failure
|
Note: This test is derived from 26.6.5.9 Handover / layer 1 failure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.11.1 Conformance requirements
|
The MS shall return to the old channel in the case of a handover failure caused by a layer 1 failure on the target cell. On the old channel the MS shall use the AMR Parameters that it was previously using on that channel.
References
3GPP TS 04.08 / 3GPP TS 44.018 section 3.4.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.11.2 Test purpose
|
To verify the contents in the message HANDOVER FAILURE .
To verify the mobile returns to the correct channel configuration prior to handover following the handover failure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.16.11.3 Method of test
|
Initial Conditions
System Simulator:
2 cells with same LAI, default parameters.
Mobile Station:
The MS is in the active state (U10) of a call (on cell A). Used power level is the maximum supported by the MS.
Specific PICS statements:
- Speech supported for Half rate version 3 (HR AMR).
- Speech supported for Full rate version 2 (GSM EFR)
- Speech supported for Half rate version 1 (GSM HR)
PIXIT statements:
-.
Foreseen Final State of the MS
The active state (U10) of a mobile call (on cell A). Used power level is the maximum supported by the MS.
Test Procedure
The MS is in the active state (U10) of a call on cell A. The SS sends a HANDOVER COMMAND on the main DCCH. The MS shall begin to send access bursts at the commanded power level on the new DCCH (and optionally on the SACCH) to cell B. With the exception of normal BCCH signalling, the SS does not transmit anything on cell B (thus causing a time-out of T3124). The MS shall re-establish the old link on cell A and send a HANDOVER FAILURE within 3 seconds from the transmission of HANDOVER COMMAND.
Maximum Duration of Test
10 minutes
Expected Sequence
This test is repeated for M=1, M=2 (only if MS supports half rate version 3), M=3, M=4, M=5 (only if MS supports half rate version 3), M=6 (only if MS supports half rate version 3), M=7 (only if MS supports full rate version 2), M=8 (only if MS supports half rate version 1).
This test is repeated for K=1, K=2 (only if MS supports half rate version 3).
Step
Direction
Message
Comments
1
SS
-
The MS and SS are in the active state of a call on a Multirate channel (full rate version 3 where K=1 or half rate version 3 where K=2).
2
SS -> MS
HANDOVER COMMAND
Channel description: non-hopping. Synchronization Indication: non synchronized.
3
MS -> SS
HANDOVER ACCESS
Several messages are sent, all with correct Handover References.
4
MS -> SS
HANDOVER FAILURE
Sent on old channel, RR cause value = "Abnormal release, unspecified", "Abnormal release, channel unacceptable", "Abnormal release, timer expired", "Abnormal release, no activity on the radio path" or "Protocol error unspecified". Shall be sent within 3 seconds from the transmission of HANDOVER COMMAND.
5
MS
-
The SS checks that the codec mode used by the MS is the same as in step 1.
Specific Message Contents
M=1
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
Not specified
M=2
This sequence shall not be performed when K = 1. This step is applicable only if the MS supports half rate version 3.
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
Not specified
M=3
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
M=4
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
M=5
This step is applicable only if the MS supports half rate version 3.
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 0
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
M=6
This step is applicable only if the MS supports half rate version 3.
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
ICMI = 1
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
M=7
This step is applicable only if the MS supports full rate version 2.
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 2
M=8
This step is applicable only if the MS supports half rate version 1.
HANDOVER COMMAND
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 1
K=1
ASSIGNMENT COMMAND
Information Element
value/remark
Channel description
TCH/F
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
K=2
This step is applicable only if the MS supports half rate version 3.
ASSIGNMENT COMMAND
Information Element
value/remark
Channel description
TCH/H
Channel mode
Mode
Speech full or half rate version 3
Multi-Rate configuration
Arbitrary set of codec modes, thresholds and hysteresis
specified according to 3GPP TS 05.09 / 45.009
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17 Adaptive Multi Rate Signalling – 8PSK
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.1 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.2 Inband Signalling, Uplink Codec Adaptation
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.2.1 Conformance Requirement
|
The MS shall after reception of a Codec Mode Command apply the corresponding codec mode in the uplink direction for the next possible speech frame and no more than three speech frames later.
NOTE: This test is not intended to verify these conformance requirements, but to verify the correctness of the involved layer 1 and layer 3 signalling.
References:
3GPP TS 45.009 subclauses 3.3 and 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.2.2 Test Purpose
|
This test is concerned with the link adaptation for AMR uplink and the related inband signalling. The test shall verify that the MS in the uplink direction applies the codec mode indicated by the network transmitted Codec Mode Commands, and that the MS correctly signals the used codec as Codec Mode Indication in the uplink inband signalling.
NOTE: The inband signals are L1 signalling transmitted every speech frame, as defined in 3GPP TS 45.009: In uplink directions Codec Mode Requests and Codec Mode Indications are transmitted alternately, whereas downlink signalling contains of alternately Codec Mode Commands and Codec Mode Indications.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.2.3 Method of Test
|
Initial Conditions
The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
a) A mobile originated call is initiated, following the CHANNEL REQUEST received from the MS the SS sends an IMMEDIATE ASSIGNMENT to the MS commanding it to go to a SDCCH. The MS indicates to the SS that it supports the multi-rate speech codec. The SS allocates the MS a O-TCH/AHS and signals the allowed codec subset and adaptation thresholds as part of the ASSIGNMENT COMMAND. DTX shall not be activated. Hopping is activated. The hopping band is centred around an ARFCN in the Mid ARFCN range. The hopping frequencies are chosen from those defined in clause 6.
The following active codec mode subset shall apply:
Codec Mode
O-TCH/AHS in kbit/s
CODEC_MODE_1
4,75
CODEC_MODE_2
5,9
CODEC_MODE_3
7,95
CODEC_MODE_4
12,2
The following decision threshold and hysteresis values in terms of normalized carrier to interference ratio (C/Inorm), shall apply for Codec Mode Command / Request (MC', MR'):
MC'/MR'
THR_MC_Dn(MC')/
THR_MR_Dn(MR')
THR_MC_Up(MC')/
THR_MR_Up(MR')
CODEC_MODE_4
16,5 dB
+
CODEC_MODE_3
11,5 dB
18,5 dB
CODEC_MODE_2
6,5 dB
13,5 dB
CODEC_MODE_1
8,5 dB
b) The SS signals that a new codec is wanted in uplink direction by changing the value of the Codec Mode Command. The MS shall apply the commanded mode in uplink by changing the mode and correspondingly the value of the Codec Mode Indication to match the used codec. This is repeated for all neighbouring mode transitions in the Active Codec Set.
Maximum Duration of Test
2 minutes
Expected Sequence in step b)
Step
Direction
Message
Comments
1
SS->MS
Codec Mode Command change
Codec Mode 3 is commanded by inband signalling
2
MS->SS
Codec Mode Indication change
Codec Mode Indication shows current active mode in uplink, thus changed when mode changes
3
SS->MS
Codec Mode Command change
Codec Mode 2 is commanded by inband signalling
4
MS->SS
Codec Mode Indication change
Codec Mode 2 is indicated in inband signalling with first frame using Codec Mode 2
5
SS->MS
Codec Mode Command change
Codec Mode 1 is commanded by changing inband signal
6
MS->SS
Codec Mode Indication change
Codec Mode 1 is indicated in inband signalling with first frame using Codec Mode 1.
7
SS->MS
Codec Mode Command change
Codec Mode 2 is commanded by changing inband signal
8
MS->SS
Codec Mode Indication change
Codec Mode 2 is indicated in inband signalling with first frame using Codec Mode 2.
9
SS->MS
Codec Mode Command change
Codec Mode 3 is commanded by changing inband signal
10
MS->SS
Codec Mode Indication change
Codec Mode 3 is indicated in inband signalling with first frame using Codec Mode 3.
11
SS->MS
Codec Mode Command change
Codec Mode 4 is commanded by changing inband signal
12
MS->SS
Codec Mode Indication change
Codec Mode 4 is indicated in inband signalling with first frame using Codec Mode 4
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
Value/remark
Assignment Command
In step a) of Test Procedure: codec mode 4 selected
(ref: 3GPP TS 44.018 subclause 9.1.2)
Codec mode commands, downlink inband signalling
Information Element
Value/remark
Channel Mode to be used for uplink
In step a) of Test Procedure: Codec Mode 4 commanded
In step 1-2: Codec Mode 3 commanded
In step 3-4: Codec Mode 2 commanded
In step 5-6: Codec Mode 1 commanded
In step 7-8: Codec Mode 2 commanded
In step 9-10: Codec Mode 3 commanded
In step 11-12: Codec Mode 4 commanded
Codec mode indications, uplink inband signalling
Information Element
Value/remark
Indicating Codec Mode currently used uplink
In step a) of Test Procedure: Codec Mode 4 indicated
In step 1: Codec Mode 4 indicated
In step 2-3: Codec Mode 3 indicated
In step 4-5: Codec Mode 2 indicated
In step 6-7: Codec Mode 1 indicated
In step 8-9: Codec Mode 2 indicated
In step 10-11: Codec Mode 3 indicated
In step 12: Codec Mode 4 indicated
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.3 8-PSK AMR HR / Structured procedures / MS terminated call / early assignment / no initial codec mode
|
NOTE: this test is derived from the one described in subclause 26.16 and entitled: "Structured procedures / MS terminated call / early assignment / no initial codec mode"
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.3.1 Conformance requirement
|
1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying using CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) The ASSIGNMENT command will not specify which of the codec modes the MS should use, but allow the handset to select the default codec mode.
4) For speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
CHx: identifies any of the Channel Codec mode.
HR: half rate channel.
References:
3GPP TS 44.018 subclauses 9.1.2 and 9.1.5.
3GPP TS 45.009 subclause 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.3.2 Test purpose
|
1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying using CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) To verify that upon receipt of an ASSIGNMENT COMMAND with no codec mode specified, the MS shall use the default codec mode.
4) To verify that for speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.3.3 Method of Test
|
Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
The following test is performed for the half rate channel mode of the multi-rate codec:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M = 1, 2, 3, 4.
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on the correct paging sub-channel
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
SETUP
11
MS->SS
CALL CONFIRMED
If the MS supports an Immediate connection then branch A applies. If the MS doesn't support an immediate connection then branch B applies.
A12
MS->SS
CONNECT
sent on the old channel
A13
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes, but does not identify a mode for immediate operation.
A14
MS->SS
ASSIGNMENT COMPLETE
B12
SS->MS
ASSIGNMENT COMMAND
B13
MS->SS
ASSIGNMENT COMPLETE
Sent on the new channel. SS allocates allowed subset codec modes, but does not identify a mode for immediate operation.
B14
MS->SS
ALERTING
B15
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
B16
MS
The MS is made to accept the call.
B17
MS->SS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the default codec mode specified.
19
SS->MS
CONNECT ACK
20
MS
The MS is made to release the call.
21
MS->SS
DISCONNECT
22
SS->MS
RELEASE
23
MS->SS
RELEASE COMPLETE
24
SS->MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
1 codec mode specified
M = 2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
2 codec modes and threshold values specified
M = 3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
3 codec modes and threshold values specified
M = 4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
4 codec modes and threshold values specified
26.17.3a 8-PSK AMR HR / Structured procedures / MS terminated call / early assignment / specified initial codec mode
NOTE: this test is derived from the one described in subclause 26.16.3a and entitled: "Structured procedures / MS terminated call / early assignment / specified initial codec mode"
26.17.3a.1 Conformance requirement
1) In acceptance to a SETUP message indicating speech, the MS shall indicate and include in the CALL CONFIRMED message all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message specifying using CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) The ASSIGNMENT COMMAND will specify the subset of codec modes that the MS is allowed to use for the call, the thresholds and the initial codec mode for immediate use by the MS.
4) For speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
CHx: identifies any of the Channel Codec mode.
HR: half rate channel.
References:
3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 45.009 subclause 3.4.
26.17.3a.2 Test purpose
1) To verify that, in acceptance to a SETUP message indicating speech, the MS indicates and includes in the CALL CONFIRMED message all the speech versions that it supports.
2) To verify that upon receipt of the ASSIGNMENT COMMAND message specifying using CHx/HR the Mobile Station continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT command with an ASSIGNMENT COMPLETE message; and
b) by continuing the call establishment by through connecting TCH in both directions if it supports immediate connect or by sending an ALERTING message otherwise.
3) To verify that upon receipt of an ASSIGNMENT COMMAND with codec mode specified, the MS shall use that specified codec mode.
4) To verify that for speech calls, the mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
26.17.3a.3 Method of Test
Initial Conditions
SS 1 cell, default parameters
MS in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
- Immediate connect supported for all circuit switched basic services.
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
"Idle, updated", with TMSI allocated.
Test Procedure
The following test is performed for the half rate channel mode of the multi-rate codec:
A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M=1,2,3,4.
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on the correct paging sub-channel
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
PAGING RESPONSE
Message is contained in the SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
SS->MS
SETUP
11
MS->SS
CALL CONFIRMED
If the MS supports an Immediate connection then branch A applies. If the MS doesn’t support an immediate connection then branch B applies.
A12
MS->SS
CONNECT
sent on the old channel
A13
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes and identifies a mode for immediate operation.
A14
MS->SS
ASSIGNMENT COMPLETE
B12
SS->MS
ASSIGNMENT COMMAND
B13
MS->SS
ASSIGNMENT COMPLETE
SS allocates allowed subset codec modes and identifies a mode for immediate operation.
B14
MS->SS
ALERTING
B15
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
B16
MS
The MS is made to accept the call.
B17
MS->SS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
19
SS->MS
CONNECT ACK
20
MS
The MS is made to release the call.
21
MS->SS
DISCONNECT
22
SS->MS
RELEASE
23
MS->SS
RELEASE COMPLETE
24
SS->MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start Mode specified
1 codec mode specified
M = 2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start Mode specified
2 codec modes and threshold vales specified
M = 3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start Mode specified
3 codec modes and threshold vales specified
M = 4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start Mode specified
4 codec modes and threshold vales specified
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.4 8-PSK AMR HR / Structured procedures / MS originated call / late assignment / specified initial codec mode
|
NOTE: This test is derived from the one described in subclause 26.16.4 and entitled: "Structured procedures / MS originated call / late assignment / specified initial codec mode".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.4.1 Conformance requirement
|
1) The MS shall indicate and include in the mobile originating SETUP for speech call all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message using half rate speech version 6, the Mobile Station starts a normal channel assignment procedure. It means that the MS initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause 'normal event', to the network on the main DCCH.
References:
3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 45.009 subclause 3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.4.2 Test purpose
|
1) To verify that the MS indicates and includes in the mobile originating SETUP for speech call all the speech versions that it supports.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating using half rate speech version 6, the MS sends an ASSIGNMENT COMPLETE message. The ASSIGNMENT COMMAND message will also identify which codec mode the MS is allowed to use for the call, the threshold values and the initial codec mode for immediate use.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.4.3 Method of Test
|
Initial Conditions
SS 1 cell, default parameters.
MS in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
-
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
The MS has a MO call in state U10, "active".
Test Procedure
The following test is performed for the half rate channel mode of the multi-rate codec.
The MS is made to initiate a speech call. The call is established with a late assignment.
Maximum Duration of Test
3 minutes.
Expected Sequence
This test is repeated for M = 1, 2, 3, 4.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
SETUP
The MS indicates it supports the HR speech version 6.
11
SS->MS
CALL PROCEEDING
12
SS->MS
ALERTING
13
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
14
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset codec modes, but does identifies a mode for immediate operation.
15
MS->SS
ASSIGNMENT COMPLETE
16
SS->MS
CONNECT
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
MS->SS
CONNECT ACK
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start mode specified
1 codec mode specified
M = 2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start mode specified
2 codec modes and threshold vales specified
M = 3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start mode specified
3 codec modes and threshold vales specified
M = 4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 1
Start mode specified
4 codec modes and threshold vales specified
26.17.4a 8-PSK AMR HR / Structured procedures / MS originated call / late assignment / no initial codec mode
NOTE: This test is derived from the one described in subclause 26.16.4a and entitled: "Structured procedures / MS originated call / late assignment / no initial codec mode".
26.17.4a.1 Conformance requirement
1) The MS shall indicate and include in the mobile originating SETUP for speech call all the speech versions that it supports.
2) Upon receipt of the ASSIGNMENT COMMAND message using half rate speech version 6, the Mobile Station starts a normal channel assignment procedure. It means that the MS initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause 'normal event', to the network on the main DCCH. The ASSIGNMENT COMMAND message will also specify the subset of codec modes that the MS is allowed to use for the call and the threshold values. The ASSIGNMENT COMMAND will not specify the initial codec mode but will, rather, allow the MS to select the default codec mode.
- If the Initial Codec Mode is not signalled, then the default Initial Codec Mode is given by the following implicit rule. If the Active Codec Set contains:
1 mode then this shall be the Initial Codec Mode.
2 or 3 modes then the Initial Codec mode shall be the most robust mode of the set (with lowest bit rate).
4 modes then the Initial Codec Mode shall be the second most robust mode of the set (with second lowest bit rate. If the Active Codec Set is changed during the call, then this default Initial Codec Mode shall used until an other ICM is explicitly signalled.
References
3GPP TS 44.018 subclauses 9.12 and 9.1.5.
3GPP TS 45.009 subclause 3.4.
26.17.4a.2 Test purpose
1) To verify that the MS indicates and includes in the mobile originating SETUP for speech call all the speech versions that it supports.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating using speech half rate speech version 6, the MS sends an ASSIGNMENT COMPLETE message. The ASSIGNMENT COMMAND message will also specify the subset of codec modes that the MS is allowed to use for the call and the threshold values. The ASSIGNMENT COMMAND will not specify the initial codec mode but will, rather, allow the MS to select the default codec mode.
26.17.4a.3 Method of Test
Initial Conditions
SS 1 cell, default parameters
MS in MM-state "idle, updated" with valid TMSI and CKSN
Specific PICS statements:
-
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of MS
The MS has a MO call in state U10, "active".
Test Procedure
The following test is performed for the half rate channel mode of the multi-rate codec.
The MS is made to initiate a speech call. The call is established with a late assignment.
Maximum Duration of Test
3 minutes
Expected Sequence
This test is repeated for M=1,2,3,4.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
SETUP
The MS indicates support of the HR speech version 6.
12
SS->MS
CALL PROCEEDING
13
SS->MS
ALERTING
14
MS
An alerting indication as defined in the PIXIT statement is given by the MS.
15
SS->MS
ASSIGNMENT COMMAND
SS allocates allowed subset of codec modes and thresholds, but does not identify a mode for immediate operation.
16
MS->SS
ASSIGNMENT COMPLETE
17
SS->MS
CONNECT
18
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified (M=1 CMI=0, M=2 CMI=0, M=3 CMI=0, M=4 CMI=1).
19
MS->SS
CONNECT ACK
Specific Message Content
M = 1
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
1 codec mode specified
M = 2
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
2 codec modes and threshold vales specified
M = 3
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
3 codec modes and threshold vales specified
M =4
Assignment Command
Information Element
value/remark
Channel mode
Mode
Half rate speech version 6
Multi-Rate configuration
ICMI = 0
4 codec modes and threshold vales specified
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.5 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.6 8-PSK AMR HR / Structured procedures / emergency call
|
NOTE: this test is derived from subclause 26.16.6 - Structured procedures / emergency call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.6.1 Conformance requirement
|
1) For R97/R98 MS: The MS in the "idle, updated" state, after a successful location update, the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
For R99 and later MS: When a SIM/USIM containing stored emergency numbers is present, those numbers are identified as emergency numbers. As an optional requirement, the ME shall also identify 112 and 911 as emergency numbers irrespective of whether these are stored in the SIM/USIM. Any other emergency numbers stored in the ME shall be ignored.
When no emergency numbers are stored within the SIM the following numbers shall be stored in the ME for use as emergency numbers: 112, and 911.
When no emergency numbers are stored within the USIM the following numbers shall be stored in the ME for use as emergency numbers: 112, and 911.
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct CKSN and TMSI , with CM Service Type "emergency call establishment".
3) Authentication and cipher mode setting shall be performed successfully.
4) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
5) The AMR mobile station shall accept channel assignment to an 8-PSK AMR half rate channel and also select the correct codec mode. The call shall be set up using the 8-PSK AMR HR codec.
6) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the O-TCH/AHS shall be through connected in both directions if an appropriate channel is available.
7) The call shall be cleared correctly.
References:
3GPP TS 44.018 subclauses 3.4.3.1, 3.4.6, 9.1.2 and 9.1.5.
3GPP TS 02.30, clause 4.
3GPP TS 22.101, clause 8.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.6.2 Test purpose
|
1) To verify that a R97/R98 MS supporting speech in the MM state "idle, updated", when made to call the number 112 (for GSM 900 and DCS 1800 MS), or 911 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T_GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL REQUEST message with establishment cause "emergency call".
To verify that a R99 and later MS supporting speech in the MM state "idle, updated", when made to call the number 112 or 911, sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message specifying the correct CKSN and TMSI, with CM Service Type "emergency call establishment".
3) To verify that authentication and cipher mode setting are performed successfully.
4) To verify that after cipher mode setting acceptance by the SS, the MS sends an EMERGENCY SETUP message.
5) To verify that the AMR mobile station shall accept channel assignment to a O-TCH/AHS and also select the correct codec mode. The call shall be set up using the 8-PSK AMR HR codec.
6) To verify that subsequently the MS has through connected the TCH in both directions.
7) To verify the call is cleared correctly.
26.17.6.3 Method of Test
Initial Conditions
SS: 1 cell default parameters.
MS: The MS is in the MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen Final State of the MS
The MS is in the MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
-
PIXIT statements:
-
Test Procedure
The MS is made to initiate an emergency call. The call is established with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
3 minutes.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered
2
MS->SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS->SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
5
SS->MS
AUTHENTICATION REQUEST
6
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
7
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
8
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering
10
MS->SS
EMERGENCY SETUP
The MS indicates which speech it supports.
11
SS->MS
CALL PROCEEDING
12
SS->MS
ALERTING
13
SS->MS
ASSIGNMENT COMMAND
See specific message contents.
14
MS->SS
ASSIGNMENT COMPLETE
15
SS->MS
CONNECT
16
MS->SS
CONNECT ACK
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
DISCONNECT
19
MS->SS
RELEASE
20
SS->MS
RELEASE COMPLETE
21
SS->MS
CHANNEL RELEASE
Specific Message Contents:
Assignment Command
Information Element
value/remark
Channel description
O-TCH/AHS
Channel mode
- Mode
Half rate speech version 6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.7 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.8 Void
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9 8-PSK AMR HR / RATSCCH Protocol
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.1 AMR Configuration Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.1.1 Conformance requirements
|
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference
3GPP TS 45.009 sub-clauses: 3.2.2.3.1, 3.2.2.3.5
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.1.2 Test purpose
|
This test will verify that the MS is able to handle a properly formatted AMR_CONFIG_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
This sequence is performed for execution counter, k = 1, 2.
When k = 1, DTX is not used:
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send a properly formatted AMR_CONFIG_REQ message during the call at a programmable time.
6) The MS answers with a ACK_OK message within 3 speech frames
7) The network initiates the call release.
When k = 2, DTX is used:
1) In the serving cell, the DTX indicator is set to "MS shall use discontinuous transmission".
2) User initiates a Mobile Originated call.
3) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
4) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
5) The call is maintained during a programmable time without variation of RxLev /RxQual.
6) The SS shall send a properly formatted AMR_CONFIG_REQ message during the call at a programmable time.
7) The MS answers with a ACK_OK message within 3 speech frames.
8) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
When k=1:
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
When k=2:
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
Using DTX mode
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
AMR_CONFIG_REQ
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.2 AMR Configuration Change (abnormal)
|
26.17.9.2.1 Conformance requirements
The AMR_CONFIG_REQ message may be sent by the BTS during a call to change the AMR configuration on the radio interface without interruption of the speech transmission.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference:
3GPP TS 45.009 sub-clauses: 3.2.2.3.2, 3.2.2.3.5
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.2.2 Test purpose
|
This test will verify that the MS is able to handle an improperly formatted AMR_CONFIG_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an AMR_CONFIG_REQ message, with an incorrect CRC, during the call at a programmable time.
6) The MS answers with a ACK_ERR message within 3 speech frames
7) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
AMR_CONFIG_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->22
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
AMR_CONFIG_REQ
Information Element
value/remarks
ICM
CODEC_MODE_1
ACS
2 codec modes
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.3 Codec Mode Phase Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.3.1 Conformance requirements
|
The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference:
3GPP TS 45.009 sub-clauses: 3.2.2.3.1, 3.2.2.3.4
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.3.2 Test purpose
|
This test will verify that the MS can correctly handle a properly formatted CMI_PHASE_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send the CMI_PHASE_REQ message during the call at a programmable time. The CMI_PHASE_REQ shall be sent either in place of a "CMI" speech frame, or in place of a "CMC" speech frame, to cover both kinds of changes.
6) The MS answers with a ACK_OK message within 3 speech frames.
7) The downlink CMI phase is changed (or not) according to the CMI_PHASE_REQ message starting with speech frame N+12.
8) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
CMI_PHASE_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
CMI_PHASE_REQ
Information Element
value/remarks
CMIP
1 (default)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.4 Codec Mode Phase Change (abnormal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.4.1 Conformance requirements
|
The CMI_PHASE_REQ message may be sent by the BTS to change the phase of the Codec Mode Indication in downlink.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference
3GPP TS 45.009 sub-clauses: 3.2.2.3.2, 3.2.2.3.4
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.4.2 Test purpose
|
This test will verify that the MS can correctly handle an improperly formatted CMI_PHASE_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send the CMI_PHASE_REQ message, with an incorrect CRC, during the call at a programmable time. The CMI_PHASE_REQ shall be sent either in place of a "CMI" speech frame, or in place of a "CMC" speech frame, to cover both kinds of changes.
6) The MS answers with a ACK_ERR message within 3 speech frames.
7) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
CMI_PHASE_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
CMI_PHASE_REQ
Information Element
value/remarks
CMIP
1 (default)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.5 Threshold Change (normal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.5.1 Conformance requirements
|
The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_OK message serves as an acknowledgement that a RATSCCH REQ message has been detected, correctly decoded (no CRC error) and that it is defined for the Addressee. It defines the exact activation time in direction from Addressee to Initiator.
Reference:
3GPP TS 45.009 sub-clauses: 3.2.2.3.1, 3.2.2.3.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.5.2 Test purpose
|
This test will verify that an RATSCCH capable MS is able to handle a properly formatted THRESH_REQ message
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.5.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send a properly formatted THRESH_REQ message during the call at a programmable time.
6) The MS answers with a ACK_OK message within 3 speech frames
7) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
THRESH_REQ
See specific message contents.
19
MS->SS
ACK_OK
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
Multi-Rate configuration
2 codec modes specified
THRESH_REQ
Information Element
value/remarks
HYST3
Not defined (set to all 1s)
THRESH3
Not defined (set to all 1s)
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.6 Threshold Change (abnormal)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.6.1 Conformance requirements
|
The THRESH_REQ message may be sent by the BTS to change the thresholds in the DL Mode Request Generator.
The ACK_ERR message serves as a negative acknowledgement that a RATSCCH REQ message has been detected, i.e. the RATSCCH pattern was detected, but could not be decoded correctly (CRC error), or its content is not understandable by the addressee.
Reference:
3GPP TS 45.009 sub-clauses: 3.2.2.3.2, 3.2.2.3.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.6.2 Test purpose
|
This test will verify that an RATSCCH capable MS is able to handle an improperly formatted THRESH_REQ message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.6.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
Idle Updated, TMSI allocated and camped on cell A.
Test Procedure
1) User initiates a Mobile Originated call.
2) The network and the MS indicate Bearer capabilities IE with the AMR speech Half Rate (Version 6).
3) The network performs an assignment on a TCH channel with MultiRate configuration to the MS.
4) The call is maintained during a programmable time without variation of RxLev /RxQual.
5) The SS shall send an improperly formatted THRESH_REQ message, with an incorrect CRC, during the call at a programmable time.
6) The MS answers with a ACK_ERR message within 3 speech frames
7) The network initiates the call release.
Maximum Duration of Test
5 minutes
Expected Sequence
Step
Direction
Message
Comments
1
MS
MS is in idle mode
2
MS
MS initiates Mobile Originated call
3
MS->SS
Channel Request
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS->MS
Immediate Assignment
See Default Messages for AMR
5
MS->SS
CM Service Request
CM Service Type = Mobile Originating Call Establishment.
6
SS->MS
AUTHENTICATION REQUEST
7
MS->SS
AUTHENTICATION RESPONSE
SRES specifies correct value
8
SS->MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message
9
MS->SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
MS->SS
Setup
MS indicates supported speech versions
11
SS->MS
Call Proceeding
12
SS->MS
Alerting
13
SS->MS
Assignment Command
See specific message contents.
14
MS->SS
Assignment Complete
15
SS->MS
Connect
16
MS->SS
Connect Acknowledge
17
MS
The TCH shall be through connected by both directions in the dedicated mode, using the codec mode specified.
18
SS->MS
THRESH_REQ
Message contains an incorrect CRC
19
MS->SS
ACK_ERR
Message must be received within 3 speech frames
20
SS->MS
Disconnect
21
MS->SS
Release
22
SS->MS
Release Complete
23
SS->MS
Channel Release
Specific Message Contents
ASSIGNMENT COMMAND
Information Element
value/remarks
Channel description
O-TCH/AHS
Mode of the first channel
- Mode
Half rate version 6
THRESH_REQ
Information Element
value/remarks
HYST3
Not defined (set to all 1s)
THRESH3
Not defined (set to all 1s)
HYST2
Not defined (set to all 1s)
THRESH2
Not defined (set to all 1s)
HYST1
2 dB
THRESH1
12.5 dB
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.7 Unknown RATSCCH REQ Message
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.7.1 Conformance requirements
|
The ACK_UNKNOWN message serves as an acknowledgement that a RATSCCH REQ message has been detected and correctly decoded, but was unknown to the Addressee.
Reference:
3GPP TS 45.009 sub-clause: 3.2.2.3.3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.17.9.7.2 Test purpose
|
This test will verify that the MS can correctly handle an unknown RATSCCH REQ message.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.