hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.4 Multislot signalling / RR / Handover / successful / call under establishment / finely synchronized / relocation of channels
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.4.1 Conformance requirements
|
1) The MS shall correctly apply the handover procedure from hopping, multislot configuration, finely synchronized case to hopping, multislot configuration, synchronized case during call establishment.
2) The MS shall not change number of channels in multislot configuration but the place of each channel is changed.
3) If during call establishment a Layer 3 MM or CC message just sent by the MS is not Layer 2 acknowledged before the channel change caused by the HANDOVER COMMAND message, the MS shall send the Layer 3 message to the new cell, using the same value in the N(SD) field, after the handover procedure.
References
Conformance requirements: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.4 and 9.1.15.
3GPP TS 04.13 subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.4.2 Test purpose
|
1) To test that when the MS is ordered to make a finely synchronized handover to a synchronized cell, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly, taking into account power command, new order of channels in multislot configuration and correctly calculating the timing advance to use. Handover is done from hopping multislot configuration to hopping multislot configuration, number of channels in multislot configuration is not changed but the place of each channel is changed.
2) To test that MS correctly retransmits Layer 3 MM or CC messages, that were not acknowledged by Layer 2 before the Handover, after completion of the Handover.
3) To verify the MS transmits the HANDOVER COMPLETE message without undue delay.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.4.3 Method of test
|
Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B. The timing advance in cell A sent to the MS is y bit periods. k and y are selected such that 0 < (2k + y) mod 256 < 60.
- The frame numbers of cells A and B shall be different by 100.
GSM 450:
Cell A has:
- BCCH ARFCN = 263.
- Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291).
Cell B has:
- BCCH ARFCN = 274.
- Cell Allocation = (260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291).
GSM 480:
Cell A has:
- BCCH ARFCN = 310.
- Cell Allocation = (306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338).
Cell B has:
- BCCH ARFCN = 321.
- Cell Allocation = (307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338).
GSM 900:
Cell A has:
- BCCH ARFCN = 20.
- Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114).
Cell B has:
- BCCH ARFCN = 40.
- Cell Allocation = (14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114).
DCS 1 800:
Cell A has:
- BCCH ARFCN = 747.
- Cell Allocation = (734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844).
Cell B has:
- BCCH ARFCN = 764.
- Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844).
GSM 700:
Cell A has:
- BCCH ARFCN = 457.
- Cell Allocation = (447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508).
Cell B has:
- BCCH ARFCN = 477.
- Cell Allocation = (451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508).
GSM 850:
Cell A has:
- BCCH ARFCN = 147.
- Cell Allocation = (137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241).
Cell B has:
- BCCH ARFCN = 167.
- Cell Allocation = (141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241).
Mobile Station:
- The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
A Mobile Originating Call is initiated on cell A. After the MS has sent the SETUP message (and before the last L2 frame carrying the SETUP message is acknowledged by the SS) the SS sends ASSIGNMENT COMMAND message to MS defining used multislot configuration. MS responds with ASSIGNMENT COMPLETE message. Then the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B. After the handover timeslots are relocated. Timeslots are also overlapped (this is described in specific message contents). The MS shall then send 4 access bursts, in successive slots on the new DCCH to cell B. Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH. Then the MS shall establish a signalling link indicating the correct timing advance and power level (number of channels in multislot configuration is not changed but the place of each channel is changed) and send a HANDOVER COMPLETE message. The MS shall be "ready to transmit" the HANDOVER COMPLETE message before 1500 ms after the end of the HANDOVER COMMAND message, but not before a UA frame has been sent by the SS. The MS shall then again send the SETUP message to the SS, using the same value in the N(SD) field. Finally the SS sends a CHANNEL RELEASE to end the test.
The term "ready to transmit" is defined in 3GPP TS 04.13.
Maximum Duration of Test
5 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
Step
Direction
Message
Comments
1
--------
--------
An MO call is initiated.
2
MS -> SS
CHANNEL REQUEST
Establ. Cause = "Originating call, NECI not set to 1"
3
SS -> MS
IMMEDIATE ASSIGNMENT
See Specific Message contents.
4
MS -> SS
CM SERVICE REQUEST
CM Service Type = Mobile Originating Call Establishment.
5
MS -> SS
CLASSMARK CHANGE
Multislot class
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
8
SS -> MS
CIPHERING MODE COMMAND
9
MS -> SS
CIPHERING MODE COMPLETE
10
MS -> SS
SETUP
Last L2 frame not acknowledged by the SS.
11
SS -> MS
ASSIGNMENT COMMAND
Multislot configuration is sent to MS. See specific message contents below.
12
MS -> SS
ASSIGNMENT COMPLETE
13
MS -> SS
SETUP
Last L2 frame not acknowledged by the SS. Same N(SD) as in step 8.
14
SS -> MS
HANDOVER COMMAND
See Specific Message Contents below.
15
MS -> SS
HANDOVER ACCESS
16
MS -> SS
HANDOVER ACCESS
17
MS -> SS
HANDOVER ACCESS
See Specific message contents.
18
MS -> SS
HANDOVER ACCESS
Four messages are transmitted to cell B in 4 successive slots on the new DCCH.
Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH.
19
MS -> SS
SABM
Sent without information field.
20
SS -> MS
UA
21
MS -> SS
HANDOVER COMPLETE
The message shall be ready to be transmitted before 1500 ms after the completion of step 12.
22
SS
The header of the next uplink SACCH/M is examined and the Timing Advance and Power Level indications are examined. The correct timing advance shall be indicated. The power level indication shall indicate the power level used in the handover command.
23
MS -> SS
SETUP
Same N(SD) as in step 8.
24
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
DCS 1 800:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set.
(1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
GSM 450:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
274
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
GSM 480:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
321
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
GSM 900:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
40
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
GSM 700:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
477
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
GSM 850:
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
Channel Description
Channel Description.
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
Indicates all of the CA of cell A except for the BCCH frequency.
HANDOVER COMMAND
Information Element
value/remark
As default message contents except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
167
Channel Description 2
- Channel Type
00000
- TDMA offset
Chosen arbitrarily.
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Handover Reference
- Value
Chosen arbitrarily from the range (0, 1..255).
Power command
- Power Level
Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Frequency List after time
- Frequency List
Use Range 512 to encode the complete CA of Cell B.
Description of the multislot configuration
- Downlink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Uplink assignment
For Type 1 MS timeslots are shifted one position to right if timeslot 7 is not used. If timeslot 7 is used then timeslots are shifted one position to left. For type 2 MS timeslots are shifted one position to right taking into account rules of multislot capability described in 05.02 Annex B.
- Channel set X (1=<X<=8)
Appropriate for the test.
HANDOVER ACCESS
Information Element
value/remark
As default message contents except:
Handover Reference
- Value
Same as HANDOVER COMMAND
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.5 Multislot signalling / RR /Handover / successful / call under establishment / pre-synchronized / resource upgrading
|
If an MS does not implement the pre-synchronized handover procedure correctly then calls may fail.
If an MS does not report the observed time difference between cells correctly then pseudo synchronized handovers might not be possible for any MS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.5.1 Conformance requirements
|
1) If during call establishment a Layer 3 MM or CC message just sent by the MS is not Layer 2 acknowledged before the channel change caused by the HANDOVER COMMAND message, the MS shall send the Layer 3 message to the new cell, using the same value in the N(SD) field, after the handover procedure.
2) When the Timing Advance information element is included in the HANDOVER COMMAND, the MS shall access the new cell with the timing advance included in the Timing Advance IE.
3) The MS shall be ready to transmit the HANDOVER COMPLETE message within 650 ms of the end of the HANDOVER COMMAND message.
4) When requested to do so in the HANDOVER COMMAND message, the MS shall return the Mobile Time Difference IE in the HANDOVER COMPLETE message indicating the sum of the observed time difference between the cells and the timing advance used on the old cell.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.1.4.3 and 9.1.5.
Conformance requirement 2: 3GPP TS 05.10, subclause 6.6, 3GPP TS 04.08 subclause 9.1.16.
Conformance requirement 3: 3GPP TS 04.13, subclause 5.2.6.1.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 10.5.2.39.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.5.2 Test purpose
|
1) To verify that when the MS is ordered to make a pre-synchronized handover from hopping multislot configuration to non-hopping multislot configuration, it sends 4 access bursts on the main DCCH (before completion, additional access bursts may also be sent on the SACCH) and then activates the channel correctly and correctly calculates the time to transmit.
2) To test that the MS activates the new channels that belong to same multislot configuration correctly, taking into account upgraded resources and transmits the HANDOVER COMPLETE message without undue delay.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.3.5.3 Method of test
|
Initial Conditions
System Simulator:
- 2 cells, A and B, with same LAI, default parameters, except:
- Early classmark sending enabled in SI3 rest octets.
- The BCCH of cell A is sent k bit periods before the BCCH of cell B.
Mobile Station:
- The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
A Mobile Originating Call is initiated. The SS sends an IMMEDIATE ASSIGNMENT message allocating an SDCCH/4. The MS is commanded to use a timing advance of y bit periods on cell A. After the MS has sent the SETUP message (and before the last L2 frame carrying the SETUP message is acknowledged by the SS) the SS sends ASSIGNMENT COMMAND message to MS specifying used multislot configuration. MS responds by sending ASSIGNMENT COMPLETE message to SS. Then the SS sends a HANDOVER COMMAND, ordering the MS to switch to cell B. The MS shall then send 4 access bursts, at the commanded power level, in 4 successive slots of the new DCCH to cell B. Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH. Then the MS shall establish a signalling link using the correct timing advance and send a HANDOVER COMPLETE message. The MS shall be ready to transmit the HANDOVER COMPLETE message before 650 ms after the end of the HANDOVER COMMAND message, but not before a UA frame has been sent by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13.
The MS shall then again send the SETUP message to the SS, using the same value in the N(SD) field. Finally the SS sends a CHANNEL RELEASE to end the test.
Maximum Duration of Test
20 s.
Expected Sequence
Step
Direction
Message
Comments
1
--------
--------
An MO call is initiated.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
to an SDCCH/4.
4
MS -> SS
CM SERVICE REQUEST
5
MS -> SS
CLASSMARK CHANGE
Multislot class
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
8
SS -> MS
CIPHERING MODE COMMAND
9
MS -> SS
CIPHERING MODE COMPLETE
10
MS -> SS
SETUP
Last L2 frame not acknowledged by the SS.
11
SS -> MS
ASSIGNMENT COMMAND
Multislot configuration is sent to MS. Multislot configuration shall not have the maximum number of timeslots allocated. See specific message contents below.
12
MS -> SS
ASSIGNMENT COMPLETE
13
MS -> SS
SETUP
Last L2 frame not acknowledged by the SS. Same N(SD) as in step 10.
14
SS -> MS
HANDOVER COMMAND
See specific message contents below.
15
MS -> SS
HANDOVER ACCESS
Handover Reference as included in the
16
MS -> SS
HANDOVER ACCESS
HANDOVER COMMAND
17
MS -> SS
HANDOVER ACCESS
18
MS -> SS
HANDOVER ACCESS
Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH.
19
MS -> SS
SABM
Sent without information field.
20
SS -> MS
UA
21
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before 650 ms after the completion of step 14. Shall include the Mobile Time Difference IE with value (2k+y) mod 2,097,152 half bit periods. A tolerance of ±2 half bit periods is allowed.
22
MS -> SS
SETUP
Same N(SD) as in step 10
23
SS
-
The SS checks that the timing advance reported in the layer 1 header of the SACCH/M message that is sent in the first SACCH/M multiframe following the SABM is 9 bit periods.
24
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
GSM 450
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
274
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
GSM 480
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
321
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
P-GSM 900
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
40
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
DCS 1 800
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
GSM 700
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
477
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
GSM 850
ASSIGNMENT COMMAND
Information element
Value/remark
Channel description 2
Describes hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
- Uplink assignment
Appropriate for the test, shall not be the maximum number of timeslots.
- Downlink assignment
Appropriate for the test, but shall not be the maximum number of timeslots.
- Channel set X (1=<X<=8)
Appropriate for the test
Mode of the channel set X (1=<X<=8)
Appropriate for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Arbitrarily chosen from Cell channel description
Starting time
Omitted
Cipher mode setting
Omitted
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
167
Channel Description 2
- Channel Type
00000
- Timeslot number
A suitable value for multislot configuration, chosen arbitrarily.
- Training Sequence Code
Chosen arbitrarily
- Hopping
0 (= no hopping)
- ARFCN
Chosen arbitrarily
Synchronization Indication.
pre-synchronized; ROT=1; NCI=0.
Channel Mode IE is not included.
Description of a multislot configuration:
- Downlink assignment
More timeslots are allocated than before HANDOVER COMMAND
- Uplink assignment
Same as before HANDOVER COMMAND
- Channel set X (1=<x<=8)
Same as before HANDOVER COMMAND
Timing Advance
9 bit periods.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.4 Multislot signalling / RR / Test of the channel mode modify procedure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.4.1 Conformance requirements
|
1) When the MS has received the CHANNEL MODE MODIFY message, the mobile station changes the mode for the indicated channel and then replies by a CHANNEL MODE MODIFY ACKNOWLEDGE message indicating the new channel mode.
2) If the mobile station does not support the indicated mode, it shall retain the old mode and return the associated channel mode information in the CHANNEL MODE MODIFY ACKNOWLEDGE message.
References
Conformance requirement: 3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.6 and 9.1.5 and 9.1.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.4.2 Test purpose
|
1) To verify that the MS, in an RR connected state, acknowledges a CHANNEL MODE MODIFY message by sending a CHANNEL MODE MODIFY ACKNOWLEDGEMENT message specifying and switching to the correct mode for the channels in a multislot configuration:
- the new mode if that mode is supported;
- the old mode if the new mode is not supported.
2) This shall be verified for all existing channel modes:
- data 9,6 Kb/s:
- data 4,8 Kb/s full rate:
- data 14,4 Kb/s.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.4.3 Method of test
|
Initial Conditions
System Simulator:
- 1 cells, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Mobile Station:
- The MS is "idle updated", with TMSI allocated.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
supported radio interface rates: 12kbps, 6kbps, 3,6kbps
Foreseen final state of the MS
"Idle, updated " with TMSI allocated.
Test procedure
1) A Mobile Terminated multislot connection is initiated, however following the Channel Request received from the Mobile Station, the SS sends an Immediate Assignment to the MS commanding it to go to a TCH/F. This sets the Channel Mode automatically to "Signalling Only".
2) The SS then sends a series of CHANNEL MODE MODIFY messages to the MS. Each time it is checked that the MS responds with a CHANNEL MODE MODIFY ACKNOWLEDGE message specifying:
2.1) the channel mode that has been specified in the CHANNEL MODE MODIFY message, if the MS supports that mode (this mode then becomes the "channel mode in use");
2.2) the channel mode that was in use when the CHANNEL MODE MODIFY message has been received, if the MS does not support the channel mode specified in the CHANNEL MODE MODIFY message.
Maximum duration of test
3 minutes.
Expected Sequence
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
Sent on correct paging subchannel.
2
MS->SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS->MS
IMMEDIATE ASSIGNMENT
Assignment to a non hopping TCH/F.
4
MS->SS
PAGING RESPONSE
5
MS->SS
CLASSMARK CHANGE
Multislot class
6
SS->MS
ASSIGNMENT COMMAND
Multislot configuration,
Channel mode = 'signalling only'
7
MS->SS
ASSIGNMENT COMPLETE
8
SS->MS
CHANNEL MODE MODIFY
See specific message contents
9
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
See specific message contents
10
SS->MS
CHANNEL MODE MODIFY
See specific message contents
11
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
See specific message contents
12
SS->MS
CHANNEL MODE MODIFY
See specific message contents
13
MS->SS
CHANNEL MODE MODIFY ACKNOWLEDGE
See specific message contents
14
SS->MS
CHANNEL RELEASE
The main signalling link is released
Specific Message Contents
CHANNEL MODE MODIFY
Information Element
value/remark
Channel description
describes the already assigned dedicated channel.
Channel mode
Mode
in step 8: data 9,6 Kb/s
in step 10: data 4,8 Kb/s full rate
in step 12: data 14,4 Kb/s
CHANNEL MODE MODIFY ACKNOWLEDGE
Channel mode
Mode
In step 9: if 9.6 Kb/s suported: data 9,6 Kb/s;
otherwise: signalling only.
iIn step 11: if 4.8 Kb/s supported: data 4,8 Kb/s full rate;
otherwise: same as in step 9.
iIn step 13: if 14.4 Kb/s supported: data 14,4 Kb/s full rate;
otherwise: same as in step 11.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.5 Multislot signalling / RR / Early classmark sending
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.5.1 Conformance requirement
|
1) MS uses Controlled Early Classmark Sending procedure when indicated in SYSTEM INFORMATION TYPE 3 (ES ind bit in SI 3 Rest Octets).
1.1) If Controlled Early Classmark Sending is not allowed by network the MS does not send a CLASSMARK CHANGE message.
1.2) If Controlled Early Classmark Sending is allowed by network the MS shall send its multislot class in Mobile Station Classmark 3 in a CLASSMARK CHANGE message.
Reference
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1.4 and 3.4.10.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.5.2 Test purpose
|
1) To verify that the MS sends its multislot class in Mobile Station Classmark 3 using Controlled Early Classmark Sending procedure if allowed by network.
2) To verify that the MS does not perform Early Classmark Sending if it is not allowed.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.5.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate a multislot connection. In the first case Controlled Early Classmark Sending procedure is allowed by network, the MS performs Early Classmark sending. In the second case Controlled Early Classmark Sending procedure is not allowed by network, the MS does not send a CLASSMARK CHANGE message.
SS checks Controlled Early Classmark Change procedure from CLASSMARK CHANGE message. If Controlled Early Classmark Sending procedure is allowed by the network ES ind bit in SI 3 Resr Octets is set. If this bit is not set SS sends CHANNEL RELEASE and the main signalling link is released. If ES ind bit was set then the MS's multislot class is sent in Mobile Station Classmark 3 (octet 4) in the CLASSMARK CHANGE message.
Maximum duration of test
2 minutes.
Expected sequence
This test is executed with the following sequences in allowed and not allowed cases respectively.
After the first sequence Early classmark sending is disabled from SI3 rest octets.
Step
Direction
Message
Comments
SS
Controlled Early Classmark Sending procedure is allowed by the network.
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is: answer to paging
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
MS -> SS
CLASSMARK CHANGE
SS checks that MS sent its multislot class in Mobile Station Classmark 3.
7
SS -> MS
CHANNEL RELEASE
The main signalling link is released
Step
Direction
Message
Comments
SS
Controlled Early Classmark Sending procedure is not allowed by the network.
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is: answer to paging
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM
5
SS
SS checks for 2 seconds that no CLASSMARK CHANGE message is sent by the MS.
6
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
NOTE: Step 5: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.4.1 states that the MS shall send CLASSMARK CHANGE as early as possible. 2 seconds are chosen as a reasonable value to verify that the MS does not send a CLASSMARK CHANGE message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.1.6 Default contents of layer 3 messages for RR tests
|
26.13.1.6.1 Default contents of GSM 900 layer 3 messages for RR tests
This subclause contains the default values of GSM 900 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 900 MS under test.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this subclause, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 5 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
bit map 0.
- Cell Allocation ARFCN
Channels 20, 30, 50 and 70.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set.
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB.
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
No Attach/Detach.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
bit map 0.
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels 10, 20, 40, 80, 90, 100, 110 and 120.
- EXT-IND
This IE carries the complete BA.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
20
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
Bit map 0.
- Cell Allocation ARFCN
Channel Number 10.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value: 0002H.
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
10
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 30.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 30.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 30.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
See PICS/PIXIT.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 10, 20, 80, 90, 100, 110 or 120).
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 20.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 20.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management..
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
26.13.1.6.2 Default contents of DCS 1 800 layer 3 messages for RR tests
This subclause contains the default values of DCS 1 800 L3 messages, which unless indicated otherwise in subclause 26.6 shall be transmitted by the system simulator and which are required to be received from the DCS 1 800 MS under test. These values are used in order to be consistent with the phase 2 version of 26.6.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this subclause, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
SYSTEM INFORMATION 5 bis is not sent as a default message. For those tests that require SYSTEM INFORMATION 5 bis see the specific message contents for that test.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
Range 512.
- Cell Allocation ARFCN
Channel Numbers, 590, 650, 750 and 850.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set, 0
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
MS shall not apply.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal.
- Mobile Network Code
01 decimal.
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
Range 512.
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers, 520, 590, 600, 700, 764, 780, 810, 870.
- EXT-IND
This IE carries the complete BA. EXT-IND is 0.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not Allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf().
Uplink output power
minimum supported by the MS's power class
Propagation profile
static.
BCCH/CCCH carrier number
ARFN 590.
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
Range 512.
- Cell Allocation ARFCN
Channel Number 520.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value
0002H
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf().
Uplink output power
minimum supported by the MS's power class
Propagation profile
static.
BCCH/CCCH carrier number
520
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 650.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 650.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 650.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message:
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
- RF Power Capability
See PICS/PIXIT.
- Frequency Capability
Set to 0.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 520, 590, 600, 700, 780, 810 or 870).
Channel Description
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
All other information elements
Not present.
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 650; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 590.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 650; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 590.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even.
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
26.13.1.6.3 Default contents of GSM 450 layer 3 messages for RR tests
This subclause contains the default values of GSM 450 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 450 MS under test.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this subclause, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 5 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
Range 128.
- Cell Allocation ARFCN
Channels 263, 267, 275 and 279.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set.
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB.
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
No Attach/Detach.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
Range 128.
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels 262, 263, 274, 282, 284, 287, 290 and 293.
- EXT-IND
This IE carries the complete BA.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
263
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
Range 128.
- Cell Allocation ARFCN
Channel Number 261.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value: 0002H.
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
261
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 267.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 267.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 267.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
See PICS/PIXIT.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 261, 263, 282, 284, 287, 290 or 293).
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 263.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 263.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management..
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
26.13.1.6.4 Default contents of GSM 480 layer 3 messages for RR tests
This subclause contains the default values of GSM 480 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 480 MS under test.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this subclause, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 5 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
Range 128
- Cell Allocation ARFCN
Channels 310, 315, 322 and 326.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set.
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB.
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
No Attach/Detach.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
Range 128
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels 308, 310, 321, 329, 331, 334, 337 and 340.
- EXT-IND
This IE carries the complete BA.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
310
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
Range 128
- Cell Allocation ARFCN
Channel Number 308.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value: 0002H.
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
308
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 315.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 315.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 315.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
See PICS/PIXIT.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 308, 310, 329, 331, 334, 337 or 340).
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 310.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 310.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management..
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
26.13.1.6.5 Default contents of GSM 700 layer 3 messages for RR tests
This subclause contains the default values of GSM 700 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 700 MS under test.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this section, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 5 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
128 range.
- Cell Allocation ARFCN
Channels 457, 467, 470 and 475.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set.
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB.
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
No Attach/Detach.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
128 range
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels 447, 457, 477, 480, 499, 504, 507 and 510.
- EXT-IND
This IE carries the complete BA.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
Static.
BCCH/CCCH carrier number
457
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
128 range.
- Cell Allocation ARFCN
Channel Number 447.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value: 0002H.
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
447
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 467.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 467.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 467.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
See PICS/PIXIT.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 447, 457, 480, 499, 504, 507 or 510).
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 467; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 20.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 457.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management..
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
26.13.1.6.6 Default contents of GSM 850 layer 3 messages for RR tests
This subclause contains the default values of GSM 850 L3 messages, which unless indicated otherwise in subclause 26.13 shall be transmitted by the system simulator and which are required to be received from the GSM 850 MS under test.
The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements that are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).
In this section, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.
Default SYSTEM INFORMATION:
NOTE 1: SYSTEM INFORMATION 2 bis, SYSTEM INFORMATION 5 bis, SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
Cell A
Contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages for cell A.
(CBCH) Channel Description
Not present.
(CBCH) Mobile Allocation
Not present.
Cell Channel Description
- Format identifier
128 range.
- Cell Allocation ARFCN
Channels 147, 157, 177 and 197.
Cell Identity
- Cell Identity Value
0001H
Cell Options
- Power Control Indicator
Power Control Indicator is not set.
- DTX Indicator
MS shall not use DTX.
- Radio_Link_Timeout
8 SACCH blocks.
Cell Selection Parameters
- Cell_Reselect_Hysteresis
12 dB.
- MX_TXPWR_MAX_CCH
Minimum level.
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported.
- RXLEV_ACCESS_MIN
Minimum level.
Control Channel Description
- Attach-Detach allowed
No Attach/Detach.
- BS_AG_BLKS_RES
0 blocks reserved for access grant.
- CCCH_CONF
1 basic physical channel used for CCCH, combined with SDCCHs.
- BS_PA_MFRMS
5 multiframe periods for transmission of paging messages.
- T3212 Time-out value
Infinite.
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 6
00011110
Neighbour Cells Description
- Format identifier
128 range.
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels 137, 147, 167, 207, 217, 227, 237 and 247.
- EXT-IND
This IE carries the complete BA.
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans.
- Tx-integer
5 slots used.
- Cell Barred for Access
Cell is not barred.
- Call Reestablishment Allowed
Not allowed.
- Access Control Class
Access is not barred.
- Emergency Call allowed
Yes.
SI 1 rest octets
Not used (all bits are set to spare).
SI 2 rest octets
Not used (all bits are set to spare).
SI 3 rest octets
Not used (all bits are set to spare).
SI 4 rest octets
Not used (all bits are set to spare).
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
147
Cell B
The contents of SYSTEM INFORMATION TYPE 1 to 6 messages for cell B are identical to those of cell A with the following exceptions:
Cell Channel Description
- Format Identifier
128 range.
- Cell Allocation ARFCN
Channel Number 137.
NOTE 2: This IE needs modification when used in handover tests that command the MS to go to a frequency hopping channel in cell B.
Cell Identity
- Cell Identity Value: 0002H.
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf.
Uplink output power
minimum supported by the MS's power class.
Propagation profile
static.
BCCH/CCCH carrier number
137
Contents of ALERTING message (SS to MS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000001
All other information elements
Not present.
Contents of ASSIGNMENT COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101110
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 157.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of ASSIGNMENT COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101001
RR Cause
- RR Cause Value
Normal event.
Contents of ASSIGNMENT FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101111
RR Cause
- RR Cause Value
Depending on test.
Contents of AUTHENTICATION REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
00010010
Ciphering Key Sequence Number
- Key Sequence
Chosen arbitrarily by the test house from the range 0 to 6.
Authentication Parameter RAND
- RAND value
Chosen arbitrarily by the test house.
Contents of AUTHENTICATION RESPONSE message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X010100
Other information element(s)
Not checked.
Contents of CALL PROCEEDING message:
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1 (destination side).
Message Type
00000010
All other information elements
Not present.
Contents of CHANNEL MODE MODIFY message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010000
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Channel number 157.
Channel Mode
- Mode
Depending on test.
Contents of CHANNEL MODE MODIFY ACKNOWLEDGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00010111
Channel Description 2
- Channel Type and TDMA offset
Depending on test.
- Timeslot Number
Same as in the CHANNEL MODE MODIFY message.
- Training Sequence Code
Same as in the CHANNEL MODE MODIFY message.
- Hopping
Single RF channel.
- Frequency Band
Band number 0.
- ARFCN
Channel number 157.
Channel Mode
- Mode
Same as in the CHANNEL MODE MODIFY message.
Contents of CHANNEL RELEASE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00001101
RR Cause
- RR Cause Value
Normal event.
Contents of CHANNEL REQUEST message
Establishment Cause
Not checked.
Random Reference
Not checked.
Contents of CIPHERING MODE COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110101
Cipher Mode Setting
- algorithm identifier
cipher with A5/1.
- SC
Start ciphering.
Cipher Response
IMEI shall not be included.
Contents of CIPHERING MODE COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00110010
Mobile Identity
Not present.
Contents of the CLASSMARK CHANGE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
000100110
Mobile Station Classmark 2
See PICS/PIXIT.
Mobile Station Classmark 3
For presence and contents see PICS/PIXIT.
Contents of CM SERVICE ACCEPT message:
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
00100001
Contents of CM SERVICE REQUEST message
Protocol Discriminator
Mobility Management.
Skip Indicator
0000
Message Type
0X100100
Other information elements
Not checked.
Contents of CONFIGURATION CHANGE COMMAND message (SS to MS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110000
Multislot allocation
Appropriate for the test
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode 1=<X<=8
Appropriate for the test
Contents of CONFIGURATION CHANGE ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110001
Contents of CONFIGURATION CHANGE REJECT message (MS to SS)
Protocol Discriminator
Radio Resource
Skip Indicator
0000
Message type
00110011
RR Cause
Protocol Error Unspecified
Contents of CONNECT message (SS to MS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
1
Message Type
00000111
All other information elements
Not present.
Contents of CONNECT ACKNOWLEDGE message (MS to SS)
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
As used in the SETUP message.
TI flag
0
Message Type
0X001111
Contents of HANDOVER ACCESS message:
Handover Reference
Equal to the value included in the Handover Command message.
Contents of HANDOVER COMMAND message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101011
Cell Description
- Network Colour Code
1
- Base station Colour Code
Corresponding to target cell
- BCCH Carrier Number
Set to the BCCH carrier number of cell B. (one of 137, 147, 207, 217, 227, 237 or 247).
Channel Description 2
- Channel Type and TDMA offset
Bm + ACCHs.
- Timeslot Number
Chosen arbitrarily by the test house.
- Training Sequence Code
Chosen arbitrarily by the test house.
- Hopping
Single RF channel.
- ARFCN
Chosen arbitrarily by the test house from those supported on the target cell.
Handover Reference
- Handover Reference Value
Chosen arbitrarily by the test house.
Power Command
- Power level
Chosen arbitrarily by the test house.
Multislot allocation
- Downlink assignment
Appropriate for the test
- Uplink assignment
Appropriate for the test
- Channel set 1=<X<=8
Appropriate for the test
Channel mode
Appropriate for the test
Contents of HANDOVER COMPLETE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101100
RR cause
Normal event.
Time difference
Not present.
Contents of HANDOVER FAILURE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101000
RR cause
Dependent on the test.
Contents of IMMEDIATE ASSIGNMENT message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IA rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111111
Page Mode
- Page Mode
Normal Paging.
Channel Description
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see initial conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions), Channel number 157; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 20.
Request Reference
Pertaining to last Channel Request sent by the MS.
Timing Advance
- Timing advance value
30 bit periods.
Mobile Allocation
- Length
0
Starting Time
Not present.
IA rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT EXTENDED message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the IAX rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 18.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111001
Page Mode
- Page Mode
Normal Paging.
Channel Description 1
- Channel Type and TDMA offset
For non-combined CCCH/SDCCH (see test conditions), SDCCH/8, with subchannel chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, with subchannel chosen arbitrarily by the test house.
- Timeslot Number
For non-combined CCCH/SDCCH (see test conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, timeslot zero.
- Training Sequence Code
For non-combined CCCH/SDCCH (see initial conditions), chosen arbitrarily by the test house; For combined CCCH/SDCCH (default SS
conditions), SDCCH/4, TSC=5 (same as the BCC).
- Hopping
Single RF channel.
- ARFCN
For non-combined CCCH/SDCCH (see initial conditions),Channel number 30; For combined CCCH/SDCCH (default SS conditions), SDCCH/4, Channel number 147.
Request Reference 1
Pertaining to last Channel Request sent by the MS.
Timing Advance 1
- Timing advance value
Chosen arbitrarily by the test house.
Channel Description 2
- Channel Type and TDMA offset
Same channel type as in Channel Description 1, but different TDMA offset to that in Channel Description 1.
- Timeslot Number
equal to the value in Channel Description 1.
- Training Sequence Code
equal to the value in Channel Description 1.
- Hopping
Single RF channel.
- ARFCN
equal to the value in Channel Description 1.
Request Reference 2
Not pertaining to any Channel Requests sent by the MS.
Timing Advance 2
- Timing advance value
Chosen arbitrarily by the test house.
Mobile Allocation
- Length
0
Starting Time
Not present.
IAX rest octets
Not used (all bits set to spare).
Contents of IMMEDIATE ASSIGNMENT REJECT message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00111010
Page Mode
- Page Mode
Normal Paging.
Request Reference
Pertaining to last Channel Request sent by the MS.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
Request Reference
Not pertaining to the MS under test.
Wait Indication
0 s.
IAR rest octets
Not used (all bits set to spare).
Contents of LOCATION UPDATING REQUEST message:
Protocol Discriminator
MM message.
Skip Indicator
0000
Message Type
0X001000
Other information elements
Not checked.
Contents of PAGING REQUEST TYPE 1 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P1 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 9.
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100001
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- odd/even indication
Even.
- Type of Identity
TMSI.
- Identity Digits
TMSI previously allocated to MS.
Mobile Identity 2
Not present.
P1 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 2 message:
L2 pseudo length
This is the sum of the lengths of all the information elements present in the message except for the P2 rest octets and L2 pseudo length IEs. For the default message the L2 pseudo length is 11.
Protocol Discriminator
RR Management..
Skip Indicator
0000
Message Type
00100010
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile Identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile Identity 2
- TMSI value
TMSI not allocated to MS.
Mobile Identity
Not present.
P2 rest octets
Not used (all bits set to spare).
Contents of PAGING REQUEST TYPE 3 message:
L2 pseudo length
19
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100100
Page Mode
- Page Mode
Normal Paging.
Channels needed
- first channel
any channel.
- second channel
any channel.
Mobile identity 1
- TMSI value
TMSI previously allocated to MS.
Mobile identity 2
- TMSI value
TMSI not allocated to MS.
Mobile identity 3
- TMSI value
TMSI not allocated to MS.
Mobile identity 4
- TMSI value
TMSI not allocated to MS.
P3 rest octets
Not used (all bits set to spare).
Contents of PAGING RESPONSE message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00100111
Ciphering Key Sequence Number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available.
Mobile Station Classmark 2
Mobile Identity
- odd/even indication
Even
- Type of identity
TMSI
- Identity Digits
TMSI previously allocated to MS.
Contents of PHYSICAL INFORMATION message:
Protocol Discriminator
RR Management.
Skip Indicator
0000
Message Type
00101101
Timing advance
20 bit periods.
Contents of SETUP message; (MS to SS):
Protocol Discriminator
Call Control.
Transaction Identifier
TI value
any value from the set {0, ..., 6}.
TI flag
0
Message Type
0X000101
Other information elements
Not checked.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2 Multislot signalling / CC
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1 Multislot signalling / CC / In-call functions
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.1 Multislot signalling / CC / In-call functions / User initiated service level upgrade / successful
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.1.1 Definition
|
Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is successfully performed.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.1.2 Conformance requirements
|
1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.13.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.1.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.1.3 Test purpose
|
1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the bearer capability given in MODIFY message and already negotiated and agreed during the establishment phase of the call, may not be changed.
2) To verify that upon receipt of the MODIFY COMPLETE message with bearer capability negotiated at call setup in the MS enters the "active" state.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.1.4 Method of test
|
Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
MS is in the active state of a service using a multislot connection.
Test procedure
MS is in the active state of a multislot connection. Multislot configuration with one TCH/F is allocated. User initiates User initiated service level upgrade by sending MODIFY message including the wanted value of the Maximum number of traffic channels, this being one supported by the MS and channel modes supported by the MS. The MS enters 'mobile originating modify' state. This is verified by a status enquiry procedure.
MS receives MODIFY COMPLETE message from SS and enters the 'active' state. This is verified by a status enquiry procedure.
Maximum duration of test
3 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS -> SS
MODIFY
User initiated service level upgrade is initiated.
2
MS
MS enters the Mobile originating modify state
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U26 Mobile originated modify.
5
SS -> MS
MODIFY COMPLETE
6
MS
MS enters the active state
7
SS -> MS
STATUS ENQUIRY
8
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U10 Active.
Specific message contents
MODIFY
Information element
Value/remark
Bearer capability
Maximum number of TCH/F's the MS is able to support and channel modes supported by the MS
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.2 Multislot signalling / CC / In-call functions / User initiated service level downgrade / successful
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
25.13.2.1.2.1 Definition
|
Multislot connection is established. Multislot configuration has the maximum number of timeslots supported by the MS. User initiated service level downgrade is successfully performed.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.2.2 Conformance requirements
|
1) MS shall send MODIFY message to SS indicating that User initiated service level downgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY COMPLETE is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.13.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.1.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.2.3 Test purpose
|
1) To verify that the procedure is initiated by the MS in the "active" state of a multislot connection. It sends a MODIFY message including the wanted value of the "maximum number of traffic channels" and/or the "wanted air interface" parameters; and enters the "mobile originating modify" state. Other parameters of the bearer capability given in MODIFY message and already negotiated and agreed during the establishment phase of the call, may not be changed.
2) To verify that upon receipt of the MODIFY COMPLETE message with bearer capability negotiated at call setup in the MS enters the "active" state.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.2.4 Method of test
|
Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection. Multislot configuration has maximum number of timeslots supported by the MS.
System simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
MS is in the active state of a service using a multislot connection.
Test procedure
MS in the active state of a multislot connection. Multislot configuration has maximum number of timeslots supported by the MS. User initiates User initiated service level downgrade by sending MODIFY message including the wanted value of the Maximum number of traffic channels, this being one supported by the MS and channel modes supported by the MS. The MS enters 'mobile originating modify' state. This is verified by a status enquiry procedure.MS receives MODIFY COMPLETE message from SS and enters the active state. This is verified by a status enquiry procedure.
Maximum duration of test
3 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS -> SS
MODIFY
User initiated service level downgrade is initiated.
2
MS
MS enters the Mobile originating modify state
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U26 Mobile originated modify.
5
SS -> MS
MODIFY COMPLETE
6
MS
MS enters the active state
7
SS -> MS
STATUS ENQUIRY
8
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U10 Active.
Specific message contents
MODIFY
Information element
Value/remark
Bearer capability
One TCH/F is indicated and the channel modes supported by the MS
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.3 Multislot signalling / CC / In-call functions / User initiated service level upgrade / Time-out of timer T323
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.3.1 Definition
|
Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. Timer T323 expires. Call is cleared.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.3.2 Conformance requirements
|
1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) After timer T323 has expired MS starts call clearing by sending DISCONNECT message.
3) After receipt of RELEASE message the MS sends RELEASE COMPLETE message and goes to idle updated state.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.13.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.7.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 9.3.18 and 5.4.4.2.2,
3GPP TS 04.08 / 3GPP TS 44.018, subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.3.3 Test purpose
|
1) To verify that upon expiration of T323 (accuracy ± 10%) the MS shall initiate the procedures for call clearing with cause #102 "recovery on timer expiry".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.3.4 Method of test
|
Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
"Idle, updated", with TMSI allocated.
Test procedure
MS is in the active state of a multislot connection. Multislot configuration with one TCH/F is allocated. User initiates User initiated service level upgrade by sending MODIFY message including the wanted value of the Maximum number of traffic channels, this being one supported by the MS and channel modes supported by the MS.
Timer T323 expires and MS starts call clearing procedure by sending DISCONNECT message to SS. After MS receives RELEASE message it sends RELEASE COMPLETE message. SS sends CHANNEL RELEASE message to MS and the main signalling link is released.
Maximum duration of test
3 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS -> SS
MODIFY
User initiated service level upgrade is initiated.
2
MS
Timer T323 expires
3
MS -> SS
DISCONNECT
Cause = #102 "recovery on timer expiry"
4
SS -> MS
RELEASE
5
MS -> SS
RELEASE COMPLETE
6
SS -> MS
CHANNEL RELEASE
The main signalling link is released
Specific message contents
MODIFY
Information element
Value/remark
Bearer capability
Maximum number of TCH/F's the MS is able to support and channel modes supported by the MS
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.4 Multislot signalling / CC / In-call functions / User initiated service level upgrade / modify reject
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.4.1 Definition
|
Multislot connection is established. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is requested. SS responds to upgrade request by rejecting it. MS enters the active multislot connection state.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.4.2 Conformance requirements
|
1) MS shall send MODIFY message to SS indicating that User initiated service level upgrade is initiated.
2) MS enters CC state 'Mobile originating modify (U26)' after sending MODIFY.
3) MS enters CC state 'Active (U10)' when MODIFY REJECT is received.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 9.3.13.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.1.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.3.5.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.4.3 Test purpose
|
1) To verify that upon receipt of the MODIFY REJECT message with the bearer capability negotiated at the call setup, the MS is continuously sending user information according to current call mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.4.4 Method of test
|
Initial conditions
Mobile station:
- MS in the active state of a service using a multislot connection.
System simulator:
- 1 cell, default parameters
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
-
Foreseen final state of the MS
MS is in the active state of a service using a multislot connection.
Test procedure
MS is in the active state of a multislot connection. Multislot configuration with one TCH/F is allocated. Then user initiates User initiated service level upgrade by sending MODIFY message including the wanted value of the Maximum number of traffic channels, this being one supported by the MS and channel modes supported by the MS. The MS enters 'mobile originating modify' state. This is verified by a status enquiry procedure.SS responds to MODIFY message by sending MODIFY REJECT message to MS. MS enters the active state. This is verified by a status enquiry procedure.Maximum duration of test
1 minute.
Expected sequence
Step
Direction
Message
Comments
1
MS -> SS
MODIFY
User initiated service level upgrade is initiated.
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U26 Mobile originated modify.
4
SS -> MS
MODIFY REJECT
Cause = #58 "bearer capability not presently available".
5
MS
MS enters in the active state of multislot call
6
SS -> MS
STATUS ENQUIRY
7
MS -> SS
STATUS
Cause shall be 30# (response to enq.) and state U10 Active.
Specific message contents
MODIFY
Information element
Value/remark
Bearer capability
Maximum number of TCH/F's the MS is able to support and channel modes supported by the MS
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.2.1.5 Multislot signalling / CC / In call functions / contents of some of the messages
|
The following messages are used for testing in-call modification procedures, test cases 26.13.2.1.*, as default messages for those ones defined below. If any other values are defined in the expected sequence of the actual test cases, those values take precedence over the ones defined hereafter.
SETUP (MS to SS)
Information element
Value/remark
BC Repeat indicator
Omitted
Bearer capability 1
Appropriate for the teleservice/Bearer Service selected as an initial call mode
Bearer capability 2
Omitted
Facility
Omitted
Calling party subaddress
Omitted
Called party BCD number
As entered
Called party subaddress
Omitted
LLC repeat indicator
Omitted
Low layer compatibility I
See note
Low layer compatibility II
Omitted
HLC repeat indicator
Omitted
High layer compatibility I
See note
High layer compatibility ii
Omitted
User-user
Omitted
SS version
Omitted
CLIR suppression
Omitted
CC Capabilities
present, but contents not checked
NOTE: HLC/LLC may or may not be present. The contents of HLC/LLC are not verified.
CALL PROCEEDING
Information element
Value/remark
Repeat Indicator
Omitted
Bearer Capability 1
3GPP TS 04.08 / 3GPP TS 24.008 subclause 10.5.4.5
Bearer Capability 2
Omitted
Facility
Omitted
Progress indicator
Omitted
MODIFY
Information element
Value/remark
Bearer capability
Appropriate for the selected test
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
MODIFY COMPLETE
Information element
Value/remark
Bearer capability
Appropriate for the selected test
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
MODIFY REJECT
Information element
Value/remark
Bearer capability
Appropriate for the selected test
Cause
#58 "bearer capability not presently available".
Low layer compatibility
Appropriate for the basic service selected for the test
High layer compatibility
Appropriate for the basic service selected for the test
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3 Multislot signalling / Structured procedures
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.1 Multislot signalling / Structured procedures / MS originated call / early assignment / HSCSD / non-transparent
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.1.1 Conformance requirements
|
1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS, starts to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.
3) Subsequently after establishment of a MM connection, after MS sends its multislot class in CLASSMARK CHANGE message, the MS shall send a SETUP message with correct parameters.
4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
4.1) attach the user connection to the radio path;
4.2) return a CONNECT ACKNOWLEDGE message;
4.3) establish the RLP link.
5) User initiated service level upgrade is initiated by sending MODIFY message. After receipt of MODIFY COMPLETE message MS enters the active state.
6) After receipt of a CONFIGURATION CHANGE COMMAND message MS sends CONFIGURATION CHANGE ACKNOWLEDGE message.
7) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
8) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
NOTE: Requirements 5 and 6 are only applicable to Multislot Class 2 and above.
Reference
Conformance requirement 1: 3GPP TS 02.07.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1, 9.1.8 and 9.1.18.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.10, 9.1.11 and 9.3.23.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.5 and 9.3.6,
3GPP TS 07.01 clause 8.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.13 and 9.3.14.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.1.12b and 9.1.12c.
Conformance requirement 7: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.4.4.2.2, 9.3.7 and 9.3.18.
Conformance requirement 8: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.1.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the MS in MM state "idle, updated" and in RR idle mode, with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
3) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after MS sends it's multislot class in CLASSMARK CHANGE message, after having successfully performed the authentication and cipher mode setting procedures, the MS sends a SETUP message with correct parameters.
4) Multislot configuration with one TCH/F is allocated. To verify that subsequently, after receipt of a CALL PROCEEDING message and of an ASSIGNMENT COMMAND message allocating an appropriate TCH, after having completed the early assignment procedure by replying with the ASSIGNMENT COMPLETE message, after receipt of an ALERTING message and a CONNECT message, the MS returns a CONNECT ACKNOWLEDGE message.
5) To verify that subsequently the MS has attached the user connection to the radio path. This is verified by checking that the MS establishes the RLP link correctly and sends and receives correct RLP frames in each data block.
6) To verify that subsequently upon user requests User initiated service level upgrade, the MS sends MODIFY message and after receipt of MODIFY COMPLETE message the MS enters the active state.
7) To verify that subsequently, after receipt of a CONFIGURATION CHANGE COMMAND, after MS sends CONFIGURATION CHANGE ACKNOWLEDGE, MS through connects all bi-directional channel(s) in multislot configuration in both directions and all uni-directional channels in downlink direction. Multislot configuration is upgraded from the simplest case up to the maximum number of channels supported by MS in the HSCSD configuration. This is verified by checking that the MS sends and receives correct RLP frames in each data block.
8) To verify that subsequently upon the network initiating call clearing by sending a DISCONNECT message, the MS proceed to release the call with RELEASE.
9) To verify that subsequently, on receipt of a RELEASE COMPLETE message followed by a CHANNEL RELEASE message, the MS disconnects the main signalling link.
NOTE: Items 6 and 7 are only applicable to Multislot Class 2 and above.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.1.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display the called number
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate a HSCSD connection. The call is established with early assignment. MS enters the active state. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is successfully performed. The SS sends CONFIGURATION CHANGE COMMAND message to MS and it reply's with CONFIGURATION CHANGE ACKNOWLEDGE message. This is repeated from simplest case up to the maximum number of channels supported by the MS in the HSCSD configuration (this is performed within highest multislot class that the MS supports).
Maximum duration of test
7 minutes.
Expected Sequence
An MS supporting Multilsot Class 1 need only perform steps 1..20 and 25..28.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS
Ifsupported, the MS must display the called number in the way defined in PICS/PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "Originating call and TCH/F is needed, or originating call and the network does not set NECI bit to 1"
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM
6
MS -> SS
CLASSMARK CHANGE
Multislot class
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
MS -> SS
SETUP
Non-transparent connection
13
SS -> MS
CALL PROCEEDING
14
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation only one timeslot is allocated.
15
MS -> SS
ASSIGNMENT COMPLETE
16
SS -> MS
ALERTING
17
MS
18
SS -> MS
CONNECT
19
MS -> SS
CONNECT ACKNOWLEDGE
20
MS
The appropriate bearer channel is through connected in both directions. The RLP link establishment is initiated by the MS.
21
MS -> SS
MODIFY
User initiated service level upgrade is initiated
22
SS -> MS
MODIFY COMPLETE
23
MS
MS enters the active state
24
Next three steps are performed as many times as used multislot class has different channel combinations.
Timeslot allocation starts from simplest case and is upgraded up to the maximum that MS multislot class supports, one step at the time (within highest multislot class that the MS supports).
24A
SS -> MS
CONFIGURATION CHANGE COMMAND
Appropriate number of timeslots is selected.
24B
MS -> SS
CONFIGURATION CHANGE ACKNOWLEDGE
24C
MS
TCH(s) shall be through connected in both directions
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.2 Multislot signalling / Structured procedures / MS originated call / late assignment / HSCSD / non-transparent
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.2.1 Conformance requirements
|
1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
2) Subsequently after establishment of a MM connection, after MS sends its multislot class in CLASSMARK CHANGE message, the MS shall send a SETUP message with correct parameters.
3) Upon receipt of the ASSIGNMENT COMMAND message, the Mobile Station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause "normal event", to the network on the main DCCH.
4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
4.1) attach the user connection to the radio path;
4.2) return a CONNECT ACKNOWLEDGE message;
4.3) establish the RLP link.
5) MS sends User initiated service level upgrade with MODIFY message and after receipt of MODIFY COMPLETE message the MS enters the active state.
6) MS receives CONFIGURATION CHANGE COMMAND and answers to it by sending CONFIGURATION CHANGE ACKNOWLEDGE message.
7) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
8) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
NOTE: Requirements 5 and 6 are only applicable to Multislot Class 2 and above.
Reference
Conformance requirement 1: 3GPP TS 02.07,
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1 and 9.1.8.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.11,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.23.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.3, 9.1.2 and 9.1.3.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.5 and 9.3.6,
3GPP TS 07.01 clause 8.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.13 and 9.3.14.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.1.12b and 9.1.12c.
Conformance requirement 7: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.7, 9.3.18 and 5.4.4.2.2.
Conformance requirement 8: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.2.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message.
2) Multislot configuration with one TCH/F is allocated. To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after MS sends it's multislot class in CLASSMARK CHANGE message, after having successfully performed the authentication and cipher mode setting procedures, after having sent a SETUP message, after having received of a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating an appropriate TCH, the MS sends an ASSIGNMENT COMPLETE message.
3) To verify that subsequently, after the suite of actions specified in test purposes 1 and 2, the MS after receiving a CONNECT message returns a CONNECT ACKNOWLEDGE message.
4) To verify that subsequently the MS has attached the user connection to the radio path. This is verified by checking that the MS establishes the RLP link correctly and sends and receives correct RLP frames in each data block.
5) To verify that subsequently upon user requests User initiated service level upgrade, the MS sends MODIFY message and after receipt of MODIFY COMPLETE message the MS enters the active state.
6) To verify that subsequently, after receipt of a CONFIGURATION CHANGE COMMAND, after MS sends CONFIGURATION CHANGE ACKNOWLEDGE, MS through connects all bi-directional channel(s) in multislot configuration in both directions and all uni-directional channels in downlink direction. Multislot configuration is upgraded from the simplest case up to the maximum number of channels supported by MS in the HSCSD configuration. This is verified by checking that the MS sends and receives correct RLP frames in each data block.
7) To verify that subsequently upon the network initiating call clearing by sending a DISCONNECT message, the MS proceed to release the call with RELEASE.
8) To verify that subsequently, on receipt of a RELEASE COMPLETE message followed by a CHANNEL RELEASE message, the MS disconnects the main signalling link.
NOTE: Items 5 and 6 are only applicable to Multislot Class 2 and above.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.2.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display the called number
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate a HSCSD connection. The call is established with late assignment. MS enters the active state. Multislot configuration with one TCH/F is allocated. User initiated service level upgrade is successfully performed. The SS sends CONFIGURATION CHANGE COMMAND message to MS and it reply's with CONFIGURATION CHANGE ACKNOWLEDGE message. This is done from simplest case up to the maximum number of channels supported by the MS in the HSCSD configuration (this is performed within highest multislot class that MS supports).
Maximum duration of test
7 minutes.
Expected Sequence
An MS supporting Multilsot Class 1 need only perform steps 1..20 and 25..28.
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS
If supported, the MS must display the called number in the way defined in PICS/PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "Originating call and TCH/F is needed, or originating call and the network does not set NECI bit to 1"
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM
6
MS -> SS
CLASSMARK CHANGE
Multislot class
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
MS -> SS
SETUP
Non-transparent connection
13
SS -> MS
CALL PROCEEDING
14
SS -> MS
ALERTING
15
MS
16
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation only one timeslot is allocated.
17
MS -> SS
ASSIGNMENT COMPLETE
18
SS -> MS
CONNECT
19
MS -> SS
CONNECT ACKNOWLEDGE
20
MS
The appropriate bearer channel is through connected in both directions. The RLP link establishment is initiated by the MS.
21
MS -> SS
MODIFY
User initiated service level upgrade is initiated
22
SS -> MS
MODIFY COMPLETE
23
MS
MS enter the active state
24
Next three steps are performed as many times as used multislot class has different channel combinations.
Timeslot allocation starts from simplest case and is upgraded up to the maximum that MS multislot class supports, one step at the time (within highest multislot class that the MS supports).
24A
SS -> MS
CONFIGURATION CHANGE COMMAND
Appropriate number of timeslots is selected.
24B
MS -> SS
CONFIGURATION CHANGE ACKNOWLEDGE
24C
MS
TCH(s) shall be through connected in both directions
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.3 Multislot signalling / Structured procedures / MS originated call / early assignment / HSCSD / Transparent
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.3.1 Conformance requirement
|
1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS, starts to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.
3) Subsequently after establishment of a MM connection, after MS sends its multislot class in CLASSMARK CHANGE message, the MS shall send a SETUP message with correct parameters.
4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
4.1) attach the user connection to the radio path;
4.2) return a CONNECT ACKNOWLEDGE message.
4.3) establish the TDS link.
5) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
6) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
Reference
Conformance requirement 1: 3GPP TS 02.07.
Conformance requirement 2: 3GPP TS 02.07,
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1 and 9.1.8.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.11,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.23.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.5 and 9.3.6,
3GPP TS 07.01 clause 8.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.7, 9.3.18 and 5.4.4.2.2.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.3.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the MS in MM state "idle, updated" and in RR idle mode, with a TMSI assigned, when made to initiate a call for a selected teleservice/bearer service for HSCSD that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
3) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after MS sends it's multislot class in CLASSMARK CHANGE message, after having successfully performed the authentication and cipher mode setting procedures, the MS sends a SETUP message with correct parameters.
4) Multislot configuration with maximum number of channels supported by MS in a HSCSD configuration, is allocated. To verify that subsequently, after receipt of a CALL PROCEEDING message and of an ASSIGNMENT COMMAND message allocating an appropriate TCHs, after having completed the early assignment procedure for all traffic channel in multislot configuration by replying with the ASSIGNMENT COMPLETE message, after receipt of an ALERTING message and a CONNECT message, the MS returns a CONNECT ACKNOWLEDGE message.
5) To verify that subsequently the MS has attached the user connection to the radio path. This is verified by checking that the MS synchronises correctly to the TCHs and sends and receives correct data frames in each data block.
6) To verify that subsequently upon the network initiating call clearing by sending a DISCONNECT message, the MS proceed to release the call with RELEASE.
7) To verify that subsequently, on receipt of a RELEASE COMPLETE message followed by a CHANNEL RELEASE message, the MS disconnects the main signalling link.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.3.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
- Multislot class (TSPC_Type_Multislot_ClassX)
PIXIT statements:
- Way to display the called number
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate a HSCSD connection. Maximum number of channels supported by the MS in a HSCSD configuration, is allocated. The call is established with early assignment. Having reached the active state, the call is cleared by the SS.
Maximum duration of test
7 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered
2
MS
If supported, the MS must display the called number in the way defined in PICS/PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "Originating call and TCH/F is needed, or originating call and the network does not set NECI bit to 1"
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM
6
MS -> SS
CLASSMARK CHANGE
Multislot class
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
MS -> SS
SETUP
Transparent connection
13
SS -> MS
CALL PROCEEDING
14
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation maximum number of timeslots, that MS supports, is allocated.
15
MS -> SS
ASSIGNMENT COMPLETE
16
SS -> MS
ALERTING
17
MS
18
SS -> MS
CONNECT
19
MS -> SS
CONNECT ACKNOWLEDGE
20
MS
The appropriate bearer channel is through connected in both directions
21
SS -> MS
DISCONNECT
22
MS -> SS
RELEASE
23
SS -> MS
RELEASE COMPLETE
24
SS -> MS
CHANNEL RELEASE
The main signalling link is released
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.4 Multislot signalling / Structured procedures / MS Terminated call / early assignment / HSCSD / non-transparent
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.4.1 Conformance requirement
|
1) The MS is in MM state "idle, updated" and in RR idle mode when being paged by the network.
2) The MS sends CHANNEL REQUEST message to the network and after that it receives IMMEDIATE ASSIGNMENT message from the network
3) The MS sends PAGING RESPONSE message to network and after that MS sends its multislot class in CLASSMARK CHANGE message to the network.
4) The MS performs successfully authentication and cipher mode setting procedures.
5) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
6) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with early establishment of the traffic channel(s)
6.1) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
6.2) if the MS supports immediate connect, by continuing the call establishment by through-connecting the traffic channel(s) in both directions, or if the MS does not support immediate connect, by sending an ALERTING message.
7) An MS indicates acceptance of a MT call by sending CONNECT.
8) After receiving the CONNECT ACKNOWLEDGE message from the network the MS shall establish the RLP link.
9) User requests User initiated service level upgrade. MS sends MODIFY message and after receipt of MODIFY COMPLETE message the MS enters the active state.
10) MS receives CONFIGURATION CHANGE COMMAND message and reply's to SS by sending CONFIGURATION CHANGE ACKNOWLEDGE message.
11) The MS initiates call clearing of an active call by sending a DISCONNECT message.
12) The MS in this phase of call release, upon receipt of a RELEASE message, shall return a RELEASE COMPLETE message.
13) Subsequently the MS, upon receipt of a CHANNEL RELEASE message, shall disconnect the main signalling link.
NOTE: Requirements 9 and 10 are only applicable to Multislot Class 2 and above.
Reference
Conformance requirement 1: 3GPP TS 02.07.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1 and 9.1.8.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.2.2, 9.1.25 and 9.1.11.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.3.2, 9.2.2 and 9.2.3,
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.7, 9.1.9 and 9.1.10.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 9.3.23 and 9.3.2.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.1.2 and 9.1.3
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1.5 and 9.3.1.
Conformance requirement 7: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.5.
Conformance requirement 8: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.6,
3GPP TS 07.01 clause 8.
Conformance requirement 9: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.13 and 9.3.14.
Conformance requirement 10: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 9.1.12b and 9.1.12c.
Conformance requirement 11: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.7.
Conformance requirement 12: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 9.3.18, 9.3.19 and 5.4.4.2.2.
Conformance requirement 13: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.4.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having sent a PAGING RESPONSE message on the allocated SDCCH, after having sent multislot class in CLASSMARK CHANGE message, after having performed successful authentication and cipher mode setting procedures, after receipt of a SETUP message not containing a signal information element, returns a CALL CONFIRMED message.
2) Multislot configuration with one TCH/F is allocated. To verify that subsequently, the SS sending an ASSIGNMENT COMMAND message, the MS successfully continues a mobile terminating call establishment with early assignment of traffic channel(s):
2.1) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
2.2) by continuing the call establishment by either sending a CONNECT message or sending an ALERTING message depending on PICS/PIXIT statement.
3) To verify that the MS generates an alerting indication if an ALERTING message had to be sent.
4) To verify that if an ALERTING had been sent, subsequently, when the user accepts the call (possibly internal action as declared in PICS/PIXIT statement), the MS returns a CONNECT message.
5) To verify that the MS after receipt of a CONNECT ACKNOWLEDGE message subsequently attaches the user connection to the radio path. This is verified by checking that the MS establishes the RLP link correctly and sends and receives correct RLP frames in each data block.
6) To verify that subsequently upon user requests User initiated service level upgrade, the MS send MODIFY message and after receipt of MODIFY COMPLETE message the MS enters the active state.
7) To verify that subsequently, after receipt of a CONFIGURATION CHANGE COMMAND, after MS sends CONFIGURATION CHANGE ACKNOWLEDGE, MS through connects all bi-directional channel(s) in multislot configuration in both directions and all uni-directional channels in downlink direction. Multislot configuration is upgraded from simplest case up to the maximum number of channels supported by MS in the HSCSD configuration. This is verified by checking that the MS sends and receives correct RLP frames in each data block.
8) To verify that subsequently, the MS can initiate call clearing by sending DISCONNECT message.
9) To verify that the MS in this phase of call release, upon receipt of a RELEASE message, returns a RELEASE COMPLETE message.
10) To verify that subsequently the MS, upon receipt of a CHANNEL RELEASE message, disconnects the main signalling link.
NOTE: Items 6 and 7 are only applicable to Multislot Class 2 and above.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.4.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
• Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is paged and the resulting HSCSD connection is established. Multislot configuration with one TCH/F is allocated. User service level upgrade is performed. MS enters the active state.
For Multislot Class 2 and above, a CONFIGURATION CHANGE COMMAND message is sent to MS and it reply's with CONFIGURATION CHANGE ACKNOWLEDGE message. This is done from simplest case up to the maximum number of channels supported by the MS in the HSCSD configuration (this is performed within highest multislot class that MS supports).
Maximum duration of test
7 minutes.
Expected sequence
An MS supporting Multilsot Class 1 need only perform steps 1..20 and 25..29.
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
MS -> SS
CLASSMARK CHANGE
Multislot class
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
SS -> MS
SETUP
Message does not contain the signal IE. Setup indicates non-transparent connection.
12
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A13
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation only one timeslot is allocated.
A14
MS -> SS
ASSIGNMENT COMPLETE
A15
MS -> SS
CONNECT
B13
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation only one timeslot is allocated.
B14
MS -> SS
ASSIGNMENT COMPLETE
B15
MS -> SS
ALERTING
B16
MS
An alerting indication as defined in a PICS/PIXIT statement is given by the MS
B17
MS
The MS is made to accept the call in the way described in a PICS/PIXIT statement
B18
MS -> SS
CONNECT
19
SS -> MS
CONNECT ACKNOWLEDGE
20
MS
TCH shall be through connected in both directions.
The RLP link establishment is initiated by the MS.
21
MS -> SS
MODIFY
User initiated service level upgrade is initiated
22
SS -> MS
MODIFY COMPLETE
23
MS
MS enters the active state
24
Next three steps are performed as many times as used multislot class has different channel combinations.
Timeslot allocation starts from simplest case and is upgraded up to the maximum that MS multislot class supports, one step at the time (within the highest multislot class that MS supports).
24A
SS -> MS
CONFIGURATION CHANGE COMMAND
Appropriate number of timeslots is selected.
24B
MS -> SS
CONFIGURATION CHANGE ACKNOWLEDGE
24C
MS
MS connects all bi-directional channels in both directions and all uni-directional channels in downlink direction.
25
MS
The MS is made to release the call.
26
MS -> SS
DISCONNECT
27
SS -> MS
RELEASE
28
MS -> SS
RELEASE COMPLETE
29
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.5 Multislot signalling / Structured procedures / MS Terminated call / early assignment / HSCSD / Transparent
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.5.1 Conformance requirement
|
1) The MS is in MM state "idle, updated" and in RR idle mode when being paged by the network.
2) The MS sends CHANNEL REQUEST message to the network and after that it receives IMMEDIATE ASSIGNMENT message from the network.
3) The MS sends PAGING RESPONSE message to network and after that MS sends its multislot class in CLASSMARK CHANGE message to the network.
4) The MS performs successfully authentication and cipher mode setting procedures.
5) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
6) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with early establishment of the traffic channel(s)
6.1) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
6.2) if the MS supports immediate connect, by continuing the call establishment by through-connecting the traffic channel(s) in both directions, or if the MS does not support immediate connect, by sending an ALERTING message.
7) An MS indicates acceptance of a MT call by sending CONNECT.
8) The mobile station shall attach the user connection and establish the TDS link when receiving the CONNECT ACKNOWLEDGE message from the network.
9) MS correctly uses different ciphering bit streams on the different timeslots in a multislot configuration.
10) The MS initiates call clearing of an active call by sending a DISCONNECT message.
11) The MS in this phase of call release, upon receipt of a RELEASE message, shall return a RELEASE COMPLETE message.
12) Subsequently the MS, upon receipt of a CHANNEL RELEASE message, shall disconnect the main signalling link.
Reference
Conformance requirement 1: 3GPP TS 02.07.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1 and 9.1.8.
Conformance requirement 3: 3GPP TS 04.08/ 3GPP TS 44.018 subclauses 3.3.2.2, 9.1.25 and 9.1.11.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.3.2, 9.2.2 and 9.2.3,
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.7, 9.1.9 and 9.1.10.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 9.3.23 and 9.3.2.
Conformance requirement 6: 3GPP TS 04.08/ 3GPP TS 44.018 subclauses 9.1.2 and 9.1.3.
Conformance requirement 7: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.5.
Conformance requirement 8: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.6,
3GPP TS 07.01 clause 8.
Conformance requirement 9: 3GPP TS 03.34 subclause 5.2.5,
3GPP TS 04.08/ 3GPP TS 44.018 subclauses 3.4.7 and 9.1.9.
Conformance requirement 10: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.7.
Conformance requirement 11: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.3.19.
Conformance requirement 12: 3GPP TS 04.08/ 3GPP TS 44.018 subclause 9.1.7.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.5.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having sent a PAGING RESPONSE message on the allocated SDCCH, after having sent multislot class in CLASMARK CHANGE message which has been explicitly accepted by the network, as indicated in the last reception in the accessed cell of the SYSTEM INFORMATION TYPE 3 message, after having performed successful authentication and cipher mode setting procedures, after receipt of a SETUP message not containing a signal information element, returns a CALL CONFIRMED message.
2) Multislot configuration with maximum number of channels supported by MS in a HSCSD configuration, is allocated. To verify that subsequently, the SS sending an ASSIGNMENT COMMAND message, the MS successfully continues a mobile terminating call establishment with early assignment of traffic channel(s):
2.1) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message; and
2.2) by continuing the call establishment by either sending a CONNECT messages or sending an ALERTING message depending on PICS/PIXIT statement.
3) To verify that the MS generates an alerting indication if an ALERTING message had to be sent.
4) To verify that if an ALERTING had been sent, subsequently, when the user accepts the call (possibly internal action as declared in PICS/PIXIT statement), the MS returns a CONNECT message.
5) To verify that the MS after receipt of a CONNECT ACKNOWLEDGE message subsequently attaches the user connection to the radio path. This is verified by checking that the MS synchronises correctly to the TCHs and sends and receives correct data frames in each data block.
6) To verify that the MS correctly uses different ciphering bit streams on the different timeslots in a multislot configuration.
7) To verify that subsequently, the MS can initiate call clearing by sending a DISCONNECT message.
8) To verify that the MS in this phase of call release, upon receipt of a RELEASE message, returns a RELEASE COMPLETE message.
9) To verify that subsequently the MS, upon receipt of a CHANNEL RELEASE message, disconnects the main signalling link.
These test purposes are tested for all rates supported by the MS (full rate).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.5.3 Method of test
|
Initial conditions
Mobile Station:
- The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
System Simulator:
- 1 cell, default parameters except:
- Early classmark sending enabled in SI3 rest octets.
Specific PICS statements:
• Multislot class (TSPC_Type_Multislot_ClassX)
• Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen final state of the MS
MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is paged and the resulting HSCSD connection is established. Maximum number of channels supported by the MS in a HSCSD configuration, is allocated. Having reached the active state, the MS is made to clear the call.
Maximum duration of test
7 minutes
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
MS -> SS
CLASSMARK CHANGE
Early classmark sending Multislot class indicated
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
SS -> MS
SETUP
Message does not contain the signal IE.
12
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A13
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation maximum number of timeslots that MS supports, is allocated.
A14
MS -> SS
ASSIGNMENT COMPLETE
A15
MS -> SS
CONNECT
B13
SS -> MS
ASSIGNMENT COMMAND
In multislot allocation maximum number of timeslots that MS supports, is allocated.
B14
MS -> SS
ASSIGNMENT COMPLETE
sent on the TCH/Sm channel
B15
MS -> SS
ALERTING
B16
MS
An alerting indication as defined in a PICS/PIXIT statement is given by the MS
B17
MS
The MS is made to accept the call in the way described in a PICS/PIXIT statement
B18
MS -> SS
CONNECT
19
SS -> MS
CONNECT ACKNOWLEDGE
20
MS
The appropriate bearer channel is through connected in both directionsand the MS correctly uses different ciphering bit streams on the different timeslots.
21
MS
The MS is made to release the call.
22
MS -> SS
DISCONNECT
23
SS -> MS
RELEASE
24
MS -> SS
RELEASE COMPLETE
25
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.6 Default test conditions during layer 3 tests
|
During tests in subclause 26.13 the following default test conditions shall apply if not otherwise stated within the test description. In the table below, decimal values are normally used. Sometimes a hexadecimal value, indicated with a "H", or a binary value, indicated with a "B" is given.
GSM 450
GSM 480
General signalling conditions for all carriers
Ciphering
yes
yes
General RF-conditions for all carriers
Frequency hopping mode
Non-hopping
Non-hopping
Propagation profile
Static
Static
Downlink Input Level
63 dBVemf( )
63 dBVemf( )
Uplink output power
Minimum according to MS power class
Minimum according to MS power class
Serving cell, BCCH/CCCH carrier
Channel ARFCN
263
310
Alternative channels
274 or 276
321 or 323
Serving cell, Traffic channel, SDCCH
Channel ARFCN
267
315
Alternative channels
275 or 279
322 or 326
Power Control Indicator
0
0
Neighbouring cells BCCH/CCCH carriers
Channel ARFCN
261, 282, 284, 287, 290, 293
308, 329, 331, 334, 337, 340
Alternative channels
262, 283, 285, 288, 291, 292
309, 330, 332, 335, 338, 339
Input level
53 dBVemf( )
53 dBVemf( )
Network dependent parameters
Cell identity
0001H
0001H
Mobile country code, MCC
001 (decimal)
001 (decimal)
Mobile network code, MNC
01 (decimal)
01 (decimal)
Location area code, LAC
0001H
0001H
Frequency List
Range 128
Range 128
BCCH allocation sequence
0
0
number(BA_IND)
Cell Channel Descriptor
Range 128
Range 128
PLMN colour code, NCC
1
1
BS colour code, BCC
5
5
SMS Cell Broadcast
not active
not active
DTX
MS must not use
MS must not use
IMSI Attach-detach
MS shall not apply
MS shall not apply
CCCH_CONF
1 basic physical channel for CCCH combined with SDCCH
1 basic physical channel for CCCH combined with SDCCH
BS_AG_BLKS_RES
0 blocks reserved
0 blocks reserved
BS_PA_MFRMS
5 paging subgroups
5 paging subgroups
CELL_BAR_ACCESS
(not barred)
(not barred)
Call-re-establishment (RE)
(allowed)
(allowed)
Emergency Call allowed
allowed
same
Access Control Class (AC) (0..9, 11..15)
allowed
same
Network dependent timers
Radio_Link_Time-out
8
8
T3212 Periodic updating in decihours
Infinite
Infinite
Access control parameters
Max retrans
1
1
Tx-integer, nr. of slots
5
5
CELL_RESELECT_HYSTERESIS
12 dB
12 dB
MS_TXPWR_MAX_CCH
minimum level
minimum level
RXLEV_ACCESS_MIN
minimum
minimum
NECI
New establishment causes are not supported
same
ACS (ADDITIONAL RESELECTION
No additional cell parameters
same
PARAM IND)
are present in SI messages 7 and 8
same
P1 and C2 parameters
C2 parameters not present
same
POI and POWER OFFSET
N/A
N/A
GSM 900
DCS 1 800
General signalling conditions for all carriers
Ciphering
yes
yes
General RF-conditions for all carriers
Frequency hopping mode
Non-hopping
Non-hopping
Propagation profile
Static
Static
Downlink Input Level
63 dBVemf( )
63 dBVemf( )
Uplink output power
Minimum according to MS power class
Minimum according to MS power class
Serving cell, BCCH/CCCH carrier
Channel ARFCN
20
590
Alternative channels
40 or 60
690 or 830
Serving cell, Traffic channel, SDCCH
Channel ARFCN
30
650
Alternative channels
50 or 70
750 or 850
Power Control Indicator
0
0
Neighbouring cells BCCH/CCCH carriers
Channel ARFCN
10, 80, 90, 100, 110, 120
520, 600, 700, 780, 810, 870
Alternative channels
15, 85, 95, 105, 115, 122
530, 610, 710, 790, 820, 880
Input level
53 dBVemf( )
53 dBVemf( )
Network dependent parameters
Cell identity
0001H
0001H
Mobile country code, MCC
001 (decimal)
001 (decimal)
Mobile network code, MNC
01 (decimal)
01 (decimal)
Location area code, LAC
0001H
0001H
Frequency List
Bit Map 0
Range 512
BCCH allocation sequence
0
0
number(BA_IND)
Cell Channel Descriptor
Bit Map 0
Range 512
PLMN colour code, NCC
1
1
BS colour code, BCC
5
5
SMS Cell Broadcast
not active
not active
DTX
MS must not use
MS must not use
IMSI Attach-detach
MS shall not apply
MS shall not apply
CCCH_CONF
1 basic physical channel for CCCH combined with SDCCH
1 basic physical channel for CCCH combined with SDCCH
BS_AG_BLKS_RES
0 blocks reserved
0 blocks reserved
BS_PA_MFRMS
5 paging subgroups
5 paging subgroups
CELL_BAR_ACCESS
(not barred)
(not barred)
Call-re-establishment (RE)
(allowed)
(allowed)
Emergency Call allowed
allowed
same
Access Control Class (AC) (0..9, 11..15)
allowed
same
Network dependent timers
Radio_Link_Time-out
8
8
T3212 Periodic updating in decihours
Infinite
Infinite
Access control parameters
Max retrans
1
1
Tx-integer, nr. of slots
5
5
CELL_RESELECT_HYSTERESIS
12 dB
12 dB
MS_TXPWR_MAX_CCH
minimum level
minimum level
RXLEV_ACCESS_MIN
minimum
minimum
NECI
New establishment causes are not supported
same
ACS (ADDITIONAL RESELECTION
No additional cell parameters
same
PARAM IND)
are present in SI messages 7 and 8
P1 and C2 parameters
C2 parameters not present
same
POI and POWER OFFSET
N/A
POWER OFFSET Parameter not present.
GSM 700
GSM 850
General signalling conditions for all carriers
Ciphering
yes
yes
General RF-conditions for all carriers
Frequency hopping mode
Non-hopping
Non-hopping
Propagation profile
Static
Static
Downlink Input Level
63 dBVemf( )
63 dBVemf( )
Uplink output power
Minimum according to MS power class
Minimum according to MS power class
Serving cell, BCCH/CCCH carrier
Channel ARFCN
457
147
Alternative channels
477 or 497
167 or 187
Serving cell, Traffic channel, SDCCH
Channel ARFCN
467
157
Alternative channels
470 or 475
177 or 207
Power Control Indicator
0
0
Neighbouring cells BCCH/CCCH carriers
Channel ARFCN
447, 480, 499, 504, 507, 510
137, 207, 217, 227, 237, 247
Alternative channels
452, 465, 485, 495, 505, 509
142, 212, 222, 232, 242, 249
Input level
53 dBVemf( )
53 dBVemf( )
Network dependent parameters
Cell identity
0001H
0001H
Mobile country code, MCC
001 (decimal)
001 (decimal)
Mobile network code, MNC
01 (decimal)
01 (decimal)
Location area code, LAC
0001H
0001H
Frequency List
128 Range
128 Range
BCCH allocation sequence
0
0
number(BA_IND)
Cell Channel Descriptor
128 Range
128 Range
PLMN colour code, NCC
1
1
BS colour code, BCC
5
5
SMS Cell Broadcast
not active
not active
DTX
MS must not use
MS must not use
IMSI Attach-detach
MS shall not apply
MS shall not apply
CCCH_CONF
1 basic physical channel for CCCH combined with SDCCH
1 basic physical channel for CCCH combined with SDCCH
BS_AG_BLKS_RES
0 blocks reserved
0 blocks reserved
BS_PA_MFRMS
5 paging subgroups
5 paging subgroups
CELL_BAR_ACCESS
(not barred)
(not barred)
Call-re-establishment (RE)
(allowed)
(allowed)
Emergency Call allowed
allowed
allowed
Access Control Class (AC) (0..9, 11..15)
allowed
allowed
Network dependent timers
Radio_Link_Time-out
8
8
T3212 Periodic updating in decihours
Infinite
Infinite
Access control parameters
Max retrans
1
1
Tx-integer, nr. of slots
5
5
CELL_RESELECT_HYSTERESIS
12 dB
12 dB
MS_TXPWR_MAX_CCH
minimum level
minimum level
RXLEV_ACCESS_MIN
minimum
Minimum
NECI
New establishment causes are not supported
New establishment causes are not supported
ACS (ADDITIONAL RESELECTION
No additional cell parameters
No additional cell parameters
PARAM IND)
are present in SI messages 7 and 8
are present in SI messages 7 and 8
C2 parameters
C2 parameters not present
C2 parameters not present
POWER OFFSET
N/A
N/A
These information's are provided by system information 1, 2, 3 and 4 messages.
The system information elements that are broadcast on the SACCH/M during the dedicated mode should be consistent with those sent on the BCCH when the MS was in idle mode prior to the channel request.
In addition, all fill paging messages sent on the paging sub-channels will have by default, their page mode set to NORMAL PAGING.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.13.3.7 Default contents of messages
|
ALERTING (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
User-user
Not checked
SS version
Not checked
ALERTING (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
ASSIGNMENT COMMAND
Information element
Value/remark
Description of the first channel
describes non-hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Description of the multislot configuration
Appropriate for the teleservice selected for the test
Mode of the channel set X (1=<X<=8)
Appropriate for on bearer capability chosen for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
ASSIGNMENT COMPLETE
Information element
Value/remark
RR cause
normal event
AUTHENTICATION REQUEST
Information element
Value/remark
Ciphering key sequence number
Arbitrary
Spare half octet
(spare bits)
Authentication parameter RAND
Arbitrary
AUTHENTICATION RESPONSE
Information element
Value/remark
Authentication parameter SRES
Correct for given SRES
CALL CONFIRMED
Information element
Value/remark
Repeat indicator
Omitted
Bearer capability 1
3GPP TS 04.08 / 3GPP TS 24.008 subclause 10.5.4.5
Bearer capability 2
Omitted
Cause
Omitted
CALL PROCEEDING
Information element
Value/remark
Repeat Indicator
Omitted
Bearer Capability 1
3GPP TS 04.08 / 3GPP TS 24.008 subclause 10.5.4.5
Bearer Capability 2
Omitted
Facility
Omitted
Progress indicator
Omitted
CHANNEL RELEASE
Information element
Value/remark
RR cause
Normal event
CHANNEL REQUEST
Information element
Value/remark
Establishment cause
Answer to paging (100)
Random reference
Arbitrary value of 5 bits length
CIPHERING MODE COMMAND
Information element
Value/remark
Cipher mode setting
algorithm identifier
indicates a supported algorithm
SC
Start ciphering
Cipher response
CR
IMEI must not be included
CIPHERING MODE COMPLETE
Information element
Value/remark
Mobile equipment identity
Omitted
CLASSMARK CHANGE
Information element
Value/remark
MS classmark
Multislot classmark value appropriate for the test
Additional mobile station classmark information
Omitted
CM SERVICE ACCEPT
Information element
Value/remark
none but message head
CM SERVICE REQUEST
Information element
Value/remark
CM service type
Mobile originating call establishment or packet mode connection establishment
Ciphering key sequence number
CKSN of the MS
Mobile station classmark 2
as given by PICS.
Mobile identity
TMSI of MS
CONFIGURATION CHANGE COMMAND
Information element
Value/remark
Description of the multislot configuration
Appropriate for the teleservice selected for the test
Mode of channel set X (1=<X<=8)
Appropriate channel mode is selected
CONFIGURATION CHANGE REJECT
Information element
Value/remark
RR Cause
Cause = "Channel mode unacceptable"
CONNECT (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
Connected number
Omitted
Connected subaddress
Omitted
User-user
Omitted
CONNECT (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
Connected subaddress
Not checked
User-user
Not checked
SS version
Not checked
CONNECT ACKNOWLEDGE
Information element
Value/remark
none but message head
DISCONNECT (network to mobile station direction)
Information element
Value/remark
Cause
Coding standard
GSM
Location
User
Cause value
Normal clearing
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
DISCONNECT (mobile station to network direction)
Information element
Value/remark
Cause
Coding standard
GSM
Location
User
Cause value
Normal clearing
Facility
Not checked
User-user
Not checked
SS version
Not checked
IMMEDIATE ASSIGNMENT
Information element
Value/remark
Page mode
Normal paging
Channel description
describes a valid SDCCH+SACCH in non-hopping mode
Request reference
Random access information
As received from MS
N51, N32, N26
Corresponding to frame number of the CHANNEL REQUEST
Timing advance
Arbitrary
Mobile allocation
Empty (L=0)
Starting time
Omitted
MODIFY
Information element
Value/remark
Bearer capability
Connection element (octet 6c)
Transparent for cases: 26.13.3.3, 26.13.3.5
Non-transparent for cases: 26.13.3.1, 26.13.3.2, 26.13.3.4
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
MODIFY COMPLETE
Information element
Value/remark
Bearer capability
Connection element (octet 6c)
Transparent for cases: 26.13.3.3, 26.13.3.5
Non-transparent for cases: 26.13.3.1, 26.13.3.2, 26.13.3.4
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
Reverse call setup direction
Presence and value not checked
MODIFY REJECT
Information element
Value/remark
Bearer capability
Connection element (octet 6c)
Transparent for cases: 26.13.3.3, 26.13.3.5
Non-transparent for cases: 26.13.3.1, 26.13.3.2, 26.13.3.4
Cause
Cause = Channel Unacceptable
Low layer comp.
Appropriate for the basic service selected for the test
High layer comp.
Appropriate for the basic service selected for the test
PAGING REQUEST TYPE 1
Information element
Value/remark
L2 pseudo length
L2 pseudo length of the message
Page Mode
Normal Paging
Channels needed for Mobiles 1 and 2
channel (first)
any channel
channel (second)
any channel
Mobile identity 1
TMSI of MS under test
Mobile identity 2
Omitted
P1 rest octets
(spare octets)
PAGING RESPONSE
Information element
Value/remark
Ciphering key sequence number
Value assigned to MS in the initial conditions
Spare half octet
(spare bits)
Mobile station classmark 2
as given by PICS
Mobile identity
specifies TMSI of MS
RELEASE (network to mobile station direction)
Information element
Value/remark
Cause
Omitted
Second cause
Omitted
Facility
Omitted
User-user
Omitted
RELEASE (mobile station to network direction)
Information element
Value/remark
Cause
Not checked
Second cause
Not checked
Facility
Not checked
User-user
Not checked
SS version
Not checked
RELEASE COMPLETE (network to mobile station direction)
Information element
Value/remark
Cause
Omitted
Facility
Omitted
User-user
Omitted
RELEASE COMPLETE (mobile station to network direction)
Information element
Value/remark
Cause
Not checked
Facility
Not checked
User-user
Not checked
SS version
Not checked
SETUP (MS to SS)
Information element
Value/remark
BC Repeat indicator
Omitted
Bearer capability 1
Appropriate for the teleservice selected for the test
Bearer capability 2
Omitted
Facility
Not checked
Calling party subaddress
Not checked
Called party BCD number
As entered
Called party subaddress
Omitted
LLC repeat indicator
Omitted
Low layer compatibility I
Appropriate for teleservice selected for the test
Low layer compatibility II
Omitted
HLC repeat indicator
Omitted
High layer compatibility i
Appropriate for teleservice selected for the test
High layer compatibility ii
Omitted
User-user
Not checked
SS version
Not checked
CLIR suppression
Not checked
CC Capabilities
Not checked
SETUP (SS to MS)
Information element
Value/remark
BC repeat indicator
Omitted
Bearer capability 1
Appropriate for teleservice selected for the test
Bearer capability 2
Omitted
Facility
Omitted
Progress indicator
Omitted
Signal
Omitted
Calling party BCD number
Omitted
Calling party subaddress
Omitted
Called party BCD number
Omitted
Called party subaddress
Omitted
LLC repeat indicator
Omitted
Low layer compatibility I
Appropriate for the teleservice selected for the test
Low layer compatibility II
Omitted
HLC repeat indicator
Omitted
High layer compatibility i
Appropriate for the teleservice selected for the test
High layer compatibility ii
Omitted
User-user
Omitted
26.14 VGCS and VBS Tests
This clause applies to mobile station supporting Voice Group Call Service (TS 91) and/or Voice Broadcast Service (TS 92). The objective of this clause is to test VGCS/VBS conc erned procedures. A specific VGCS/VBS SIM card is needed for testing. If a mobile supports both VGCS and VBS, the VGCS is selected for tests except when otherwise stated.
For VGCS and VBS, the following possible mobile station implementations exist:
- support of VBS listening;
- support of VBS originating;
- support of VGCS listening;
- support of VGCS talking. This always includes the implementation for VGCS listening;
- support of VGCS originating. This always includes the implementation for VGCS talking.
Apart from the explicitly mentioned combinations, all possible combinations are optional.
In this clause some L3 messages are sent in UI format to which no L2 acknowledgement/re-transmission mechanism is applied. It is important for overall tests in this clause to ensure that the radio conditions are ideal.
Tables 26.14.1 to 26.14.3 define generic procedures to bring the MS into an initial state. For establishment of group transmit mode table 26.14.1 is used if the MS supports VGCS talking. If an MS supporting VBS originating rather than VGCS, table 26.14.2 is used for establishment of a VBS call and to bring the MS into group transmit mode. For establishment of group receive mode table 26.14.3 is applied.
Unless indicated in individual sub-clauses, the default message contents in subclause 26.14.10 are applied.
Table 26.14.1: Establishment of group transmit mode for VGCS
Step
Direction
Message
Comments
0
MS
the MS is in idle mode
1
SS -> MS
NOTIFICATION/NCH
with a description of VGCS channel and a VGCS call reference active in the MS
2
MS
After the indication of the notification, MMI action to join the VGCS call
3
SS -> MS
UPLINK FREE
4
MS
MMI action to request uplink access
5
MS -> SS
UPLINK ACCESS
6
MS -> SS
UPLINK ACCESS
7
SS -> MS
UPLINK BUSY
8
SS -> MS
VGCS UPLINK GRANT
9
MS -> SS
TALKER INDICATION
L2: SABM / UA
Table 26.14.2: Establishment of a VBS call
Step
Direction
Message
Comments
0
MS
the MS is in idle mode
1
MS
MMI action to initiate a VBS call with setup procedure.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
TCH/F, single RF channel
GSM 450: 275,
GSM 480: 322
GSM 900: 50,
DCS 1 800: 750
PCS 1 900: 650
GSM710: 470
GSM 750: 470
T-GSM 810: 470
GSM 850: 177
4
MS -> SS
CM SERVICE REQUEST
VBS establishment, L2: SABM / UA
5
SS -> MS
CM SERVICE ACCEPT
6
MS -> SS
SETUP
7
SS -> MS
CHANNEL MODE MODIFY
8
MS -> SS
CHANNEL MODE MODIFY ACKNOWLEDGE
9
SS -> MS
CONNECT
Table 26.14.3: Establishment of group receive mode for VGCS or VBS
Step
Direction
Message
Comments
0
MS
the MS is in idle mode
1
SS -> MS
NOTIFICATION/NCH
with a description of VGCS/VBS channel and a VGCS/VBS call reference active in the MS,
for VGCS call the SF set to '1', for VBS call the SF set to '0'
2
MS
After the indication of the notification, MMI action to join the VGCS/VBS call
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1 VGCS-VBS / Notification
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.1 VGCS-VBS / Notification / notification indication
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.1.1 Conformance requirement
|
1. Having received a NOTIFICATION/NCH or NOTIFICATION/FACCH which contains group call reference(s) that are active in the MS, the MS shall correctly indicate the notified group/broadcast call reference(s).
2. On request to respond to the call notification, the MS shall join the VGCS/VBS call on the correct channel if a description for the VGCS/VBS channel is included.
3. On request to respond to the call notification, the MS shall establish an RR connection to respond the notification if no description for the VGCS/VBS channel is included.
4. The MS shall ignore any NOTIFICATION/NCH or NOTIFICATION/FACCH which contains group call reference(s) that are not active in the MS.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.3.1 and 3.3.3.2.
3GPP TS 03.68 subclauses 4.1, 11.3.1.3a and 11.3.1.3b.
3GPP TS 03.69 subclauses 4.1, 11.3.1.3a and 11.3.1.3b.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.1.2 Test purpose
|
1. To verify that the MS indicates correctly the notified group/broadcast call reference(s) after receiving a NOTIFICATION/NCH or NOTIFICATION/FACCH message which contains group call reference(s) that are active in the MS.
2. To verify that the MS, on request to respond to a call notification, joins the VGCS/VBS call on the correct channel if a description for the VGCS/VBS channel is included in the NOTIFICATION message.
3. To verify that the MS, on request to respond to a call notification, establishes an RR connection to respond to the notification if no description for the VGCS/VBS channel is included in the NOTIFICATION message.
4. To verify that the MS ignores any NOTIFICATION/NCH or NOTIFICATION/FACCH which contains group call reference(s) that are not active in the MS.
5. To verify that there is no uplink transmission from the MS on TCH after the MS join the call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell default parameters for ASCI testing
Mobile Station:
The MS is in MM-state "idle, updated". No automatic answering is configured.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate a call notification.
- Way to accept a VGCS or VBS.
- Way to verify the downlink speech path.
Foreseen Final State of the MS
"Idle, updated".
Test Procedure
The MS is in idle mode, the SS sends NOTIFICATION/NCH containing VGCS/VBS channel description and VGCS/VBS call reference not active in the MS. It is checked that the MS ignores the message. The SS sends NOTIFICATION/NCH containing VGCS/VBS channel description and VGCS/VBS call reference active in the MS ("good reference"). It is checked whether the MS indicates correctly the notified group call reference(s) and joins VGCS/VBS call on request of responding to the notification. The group call is terminated. The SS sends NOTIFICATION/NCH which contains the "good reference" but no VGCS/VBS channel description. It is checked that the MS indicates correctly the notified group call reference(s) and establishes a RR connection to respond to the notification on request of responding to the call, then joins the call. The group call is terminated.
The MS is brought to group receive mode or CC state U10 or dedicated mode with signalling connection or group transmit mode (for k=1, 2, 3, 4 respectively), the SS sends NOTIFICATION/FACCH containing the "good reference" but no VGCS/VBS channel description. It is checked that the MS gives correct notified group call reference(s) and on request of responding to the call, establishes a RR connection to respond to the notification and joins the call. The call is terminated.
Finally, the MS is brought to group receive mode or CC state U10 or dedicated mode with signalling connection or group transmit mode (for k=1, 2, 3, 4 respectively), the SS sends NOTIFICATION/FACCH containing the "good reference" and VGCS/VBS channel description. It is checked the MS indicates correctly the notified group call reference(s) and joins VGCS/VBS call on request of responding to the notification. The group call is terminated.
Maximum Duration of Test
10 minutes excluding operator operations.
Expected Sequence
Test steps 20 to 50 are executed for k=1, 2, 3, 4 conditionally. If the MS does not support CC state U10, test steps 20 to 50 are not executed for k=2. If the MS does not support VGCS talking or VBS originating, test steps 20 to 50 are not executed for k=4.
Step
Direction
Message
Comments
0
MS
the MS is in idle mode
1
SS -> MS
NOTIFICATION/NCH
with a description of VGCS/VBS channel and a VGCS/VBS call reference not active in the MS
2
MS
check that the MS ignores the notification and there is no uplink transmission on that channel for 10 s.
3
SS -> MS
NOTIFICATION/NCH
with a description of VGCS/VBS channel and a VGCS/VBS call reference active in the MS
4
MS
check that the MS gives an indication containing the notified group call reference
5
MS
MMI action to join the VGCS/VBS call
6
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
7
SS
stop sending NOTIFICATION/NCH
8
SS -> MS
CHANNEL RELEASE
UI format, return to the idle updated state
9
SS
wait for the MS returning to idle updated mode and listening to NCH again
10
SS -> MS
NOTIFICATION/NCH
with a VGCS/VBS call reference active in the MS but different from step 3 and no VGCS/VBS channel description
11
MS
MMI action to join the VGCS/VBS call
12
MS -> SS
CHANNEL REQUEST
13
SS -> MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
NOTIFICATION RESPONSE
L2: SABM / UA
15
SS -> MS
CHANNEL RELEASE
release the dedicated channel with a group channel description. The MS releases L2 multiple frame link L2:DISC/UA.
16
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
17
SS
stop sending NOTIFICATION/NCH
18
SS -> MS
CHANNEL RELEASE
UI format, to return to idle updated state
19
wait 5s.
A20
MS
for k=1, the MS is brought into group receive mode
B20
for k=2, the MS is brought into CC state U10
C20
for k=3, the MS is brought into dedicated mode with a signalling connection
D20
for k=4, the MS is brought into group transmit mode
21
SS -> MS
NOTIFICATION/FACCH
with a VGCS/VBS call reference not active in the MS, but no VGCS/VBS channel description
22
MS
check that the MS ignores the notification and there is no uplink transmission on that channel for 10 s.
23
SS -> MS
NOTIFICATION/FACCH
with a VGCS/VBS call reference active in the MS, but no VGCS/VBS channel description
24
MS
check the MS's indication of the notified VGCS/VBS call reference
25
MS
MMI action to join the VGCS/VBS call
A26
for k=1, no signalling needed
B26
MS -> SS
DISCONNECT
for k=2, release the old call and the channel
B27
SS -> MS
RELEASE
B28
MS -> SS
RELEASE COMPLETE
B29
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2:DISC/UA.
C26
MS -> SS
DISC/UA
for k=3, release the original dedicated. The MS releases L2 multiple frame link L2:DISC/UA.
D26
MS -> SS
UPLINK RELEASE
for k=4, release original uplink - for VGCS only
D27
SS -> MS
CHANNEL RELEASE
UI format, to return to idle updated state - for VGCS only
D28
MS -> SS
TERMINATION REQUEST
for VBS call only
D29
SS -> MS
TERMINATION
for VBS call only
D30
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2:DISC/UA -for VBS call only
31
MS -> SS
CHANNEL REQUEST
32
SS -> MS
IMMEDIATE ASSIGNMENT
33
MS -> SS
NOTIFICATION RESPONSE
L2: SABM / UA
34
SS -> MS
CHANNEL RELEASE
with group channel description. The MS releases L2 multiple frame link L2:DISC/UA.
35
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s. if the MS supports VGCS talking
36
SS
stop sending NOTIFICATION/NCH
37
SS -> MS
CHANNEL RELEASE
UI format, return to the idle updated state
38
wait for the MS returning to idle updated mode
A
B40
MS
for k=1, the MS is brought into group receive mode
for k=2, the MS is brought into CC state U10
C40
for k=3, the MS is brought into dedicated mode with a signalling connection
D40
for k=4, the MS is brought into group transmit mode
41
SS -> MS
NOTIFICATION/FACCH
with VGCS/VBS channel description and VGCS/VBS call reference active in the MS
42
MS
check the indication of the notified VGCS/VBS call reference
43
MS
MMI action to join the VGCS/VBS call
A44
for k=1, no signalling needed
B44
MS -> SS
DISCONNECT
for k=2, release the old call and the channel
B45
SS -> MS
RELEASE
B46
MS -> SS
RELEASE COMPLETE
B47
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2:DISC/UA.
C44
MS -> SS
DISC/UA
for k=3, release the original dedicated channel. The MS releases L2 multiple frame link L2:DISC/UA.
D44
MS -> SS
UPLINK RELEASE
for k=4, release original uplink - for VGCS call only
D45
SS -> MS
CHANNEL RELEASE
UI format, to return to idle updated state - for VGCS only
D46
MS -> SS
TERMINATION REQUEST
for VBS call only
D47
SS -> MS
TERMINATION
for VBS call only
D48
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2:DISC/UA -for VBS call only
49
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
50
SS
stop sending NOTIFICATION/NCH
51
SS -> MS
CHANNEL RELEASE
UI format, to return to the idle updated state
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.2 VGCS-VBS / Notification / NCH position
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.2.1 Conformance requirement
|
The MS shall recognise correctly different NCH positions and blocks if supporting VGCS or VBS.
In the case the CCCH configuration is not compatible with the NCH position, the MS shall behave as if the NCH position field was not present.
Reference(s)
3GPP TS 05.02, subclauses 6.5.1 and 6.5.5, clause 7 and table 3.
3GPP TS 04.08 / 3GPP TS 44.018, subclause 10.5.2.32.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.2.2 Test purpose
|
To verify that the MS recognises correctly different NCH positions of first block and number of blocks.
To verify that the MS behaves as if the NCH position field was not present when the CCCH configuration is not compatible with the NCH position.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, BS_AG_BLKS_RES = 5, CCCH non-combined.
Mobile Station:
The MS is in MM-state "idle, updated". No automatic answering is configured.
Specific PICS statements:
-
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate a call notification.
Foreseen Final State of the MS
"Idle, updated".
Test Procedure
The MS is in idle mode, the SS sends SI 1 containing the 1st NCH block number = 3 (B3) and No. of blocks = 1. After the MS decodes the SI 1, the SS sends on the block B1 NOTIFICATION/NCH containing VGCS/VBS channel description and VGCS/VBS call reference active in the MS. It is checked that the MS ignores the notification. The SS stops sending NOTIFICATION/NCH on block B1, but sends on block B3 containing VGCS/VBS channel description and VGCS/VBS call reference active in the MS. It is checked that the MS indicates correctly the notified group call reference(s).
The SS stops sending NOTIFICATION/NCH on block B3 and changes SI 1 containing The 1st NCH block number = 1 and No. of blocks = 2. After the MS decodes the SI the SS sends NOTIFICATION/NCH on the block B2 containing VGCS/VBS channel description and VGCS/VBS call reference active in the MS. It is checked that the MS indicates correctly the notified group call reference(s).
The SS stops sending NOTIFICATION/NCH on block B2 and changes the CCCH configuration with combined SDCCH, BS_AG_BLKS_RES = 1. Wait 30 s. and then sends NOTIFICATION/NCH on the block B2 containing VGCS/VBS channel description and VGCS/VBS call reference active in the MS. It is checked that the MS ignores the notification.
Maximum Duration of Test
5 minutes.
Expected Sequence
Step
Direction
Message
Comments
0
MS
the MS is in idle mode
1
SS -> MS
SYSTEM INFORMATION TYPE1
containing The 1st NCH block number = 3 and No. of blocks = 1
2
SS
wait for 5 s.
3
SS -> MS
NOTIFICATION/NCH
sent on block B1, containing a VGCS/VBS channel description and a VGCS/VBS call reference active in the MS
4
MS
check that the MS ignores the notification
5
SS
stop sending NOTIFICATION/NCH on block 1
6
SS -> MS
NOTIFICATION/NCH
sent on block B3, containing a VGCS/VBS channel description and a VGCS/VBS call reference active in the MS
7
MS
check that the MS indicates the notification to user
8
MS
user action to reject the group/broadcast call
10
SS
stop sending NOTIFICATION/NCH on block 3
11
SS -> MS
SYSTEM INFORMATION TYPE 1
containing The 1st NCH block number = 1 and No. of blocks = 2
12
SS
wait for 30 s.
13
SS -> MS
NOTIFICATION/NCH
sent on block B2, containing a VGCS/VBS channel description and a VGCS/VBS call reference active in the MS
14
MS
check that the MS indicates the notification to user
15
MS
user action to reject the group/broadcast call
20
SS
change CCCH with combined SDCCH, BS_AG_BLKS_RES = 1 and stop sending NOTIFICATION/NCH on block B2
21
SS -> MS
SYSTEM INFORMATION TYPE 1
containing The 1st NCH block number = 0 and No. of block = 1
22
SS
wait for 30 s.
23
SS -> MS
NOTIFICATION/NCH
sent on block B2, containing a VGCS/VBS channel description and a VGCS/VBS call reference active in the MS
24
MS
check that the MS ignores the notification
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.3 VGCS-VBS / Notification / Reduced NCH monitoring
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.3.1 Conformance requirement
|
1. When the mobile station in idle mode enters a cell and deduces from the BCCH that an NCH is present, it shall read the NCH until it has received at least two messages on the NCH indicating NLN, with the two last received NLN being identical. Then it may stop reading the NCH until it receives on the PCH an NLN(PCH) different from the last previously received NLN.
2. If the reduced NCH monitoring mechanism is used on the NCH, when the MS in group receive mode or group transmit mode enters a cell, it should read the NCH until it has received at least two messages on the NCH indicating NLN, with the two last received NLN being identical. Then it should stop reading the NCH until it receives on the SACCH an NLN(SACCH) different from the last previously received NLN.
3. A change of the NLN status field indicates a change of information on the NCH which is not related to new calls.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.3.3.
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.15.1.2.4.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.3.2 Test purpose
|
To verify that:
1. when the MS in idle mode on a cell where a reduced monitoring is activated, it reads the NCH until it has received at least two NLN (NCH) being identical. Then it stops reading the NCH until it receives a PAGING REQUEST message of any TYPE containing an NLN (PCH) different from the last previously received NLN.
2. after the MS entered in group receive mode or group transmit mode it continues the reduced monitoring until it receives SI6 containing an NLN (SACCH) different from the last previously received NLN (SACCH).
3. when the MS in group receive mode or group transmit mode enters a new cell, it reads the NCH until it has received at least two messages on the NCH indicating NLN, with the two last received NLN being identical. Then it stops reading the NCH until it receives SI6 on the SACCH an NLN(SACCH) different from the last previously received NLN.
4. the MS understands the change of the NLN status field.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.3.3 Method of test
|
Initial Conditions
System Simulator:
2 cells with default parameters for ASCI testing, same LAI.
The values specified in Table 26.14.1.3 override the values in default contents of SI messages in subclauses 26.6.14. and 26.6.15.
Table 26.14.1.3: Default values of the system information fields
Parameter
3GPP TS 04.08 / 3GPP TS 44.018 reference
Abbr.
Normal Setting
CELL_BAR_QUALIFY
10.5.2.35
CBQ
0
CELL_RESELECT_OFFSET
10.5.2.35
CRO
0
TEMPORARY_OFFSET
10.5.2.35
TO
0
PENALTY_TIME
10.5.2.35
PT
31
Power Offset
10.5.2.35
PO
0
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated on cell A. No automatic answering configured.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating. (TSPC_AddInfo_VBS_Originating)
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate uplink granted/rejected.
- Way to accept a VGCS or VBS.
- Way to request uplink.
Foreseen Final State of the MS
"Idle, updated" on cell B.
Test Procedure
The MS is in idle mode on cell A. The SS sends NOTIFICATION/NCH with NLN (value is '00'B) but not addressing the MS on cell A. After at least 2 such messages have been received by the MS, the SS sends another NLN value ('01'B) in the NOTIFICATION/NCH message which contains call reference active in the MS and VGCS/VBS channel description. It is checked that the MS does not indicate the notification. The SS sends PAGING REQUEST TYPE1 message on the MS's paging sub-channel on cell A with NLN(PCH) containing value '01'B. It is checked that the MS indicates the notification to the user. The MS rejects the VGCS/VBS call on request from MMI. The same procedure is repeated once except SS sends PAGING REQUEST TYPE2 message instead of PAGING REQUEST TYPE1. The NLN value is set to '10'B.
Change the RF levels of cell A and cell B so that the MS re-selects cell B. The same test procedure as described above is repeated once except the SS sends PAGING REQUEST TYPE 3 message on the MS's paging sub-channel on cell B. The NLN value is set to '11'B. The MS joins the VGCS/VBS call on request from MMI and is in group receive mode on cell B.
On cell A the SS sends NOTIFICATION/NCH containing VGCS/VBS channel description, the same call reference and NLN value as those of cell B. Adjust the RF levels of cell A and cell B so that cell B keeps suitable but the MS re-selects cell A. The MS is still in group receive mode. After the MS has consecutively received at least two identical NLN (NCH) the SS sends NOTIFICATION/NCH containing an NLN valued '01'B, VGCS/VBS channel description and call reference active in the MS. It is checked that the MS does not indicate the notification. The SS changes NLN value to '01'B in SI 6 message. It is checked that the MS indicates the notification to the user. The call is rejected. The SS changes NLN status value to '1'B in SI 6 message. It is checked that the MS does not indicate any new notification to the user.
The MS is brought into group transmit mode and handed over to cell B. After at least two NOTIFICATION/NCH messages received on cell B, the SS sends an another NOTIFICATION/NCH message with NLN value ('00'B) and addressing the MS on cell B. It is checked that the MS does not indicate the notification. The SS changes NLN value to '00'B in SI 6 message. It is checked that the MS indicates the notification to the user.
Maximum Duration of Test
10 minutes
Expected Sequence
Test steps 0 to 8 are executed for k=1, 2, 3. When finished the test then goes to step 9. If the MS does not support VGCS talking, test step 18 to 44 are not executed.
Step
Direction
Message
Comments
A0, B0
MS
for k=1, 2 the MS is in idle mode on cell A. The following messages are received and sent on cell A.
C0
for k=3, adjust the power level of cell A to 32 dBV emf() so that the MS re-selects cell B. The following messages are sent and received on cell B.
1
SS -> MS
NOTIFICATION/NCH
with an initial NLN, a channel description and a call reference not addressing MS.
2
SS
wait 1 second, ensuring that the MS has consecutively received at least two identical NLN (NCH).
3
SS -> MS
NOTIFICATION/NCH
with an NLN different to step 1, a call reference active in the MS. For k= 1, 2, 3, each NLN is different.
A5
SS -> MS
PAGING REQUEST TYPE 1
for k=1, with the NLN (PCH) same as step 3
B5
SS -> MS
PAGING REQUEST TYPE 2
for k=2, with the NLN (PCH) same as step 3.
C5
SS -> MS
PAGING REQUEST TYPE 3
for k=3, with the NLN (PCH) same as step 3.
6
SS
wait 1 s.
7
MS
check that the MS indicates the notification sent in step 5.
A8, B8
MMI action to reject the VGCS/VBS call. The MS remains in idle mode on cell A.
C8
MMI action to join the VGCS/VBS call. The MS is in group receive mode on cell B.
9
SS -> MS
NOTIFICATION/NCH
sent on cell A with a channel description, the same NLN and the call reference in step C5.
10
SS
adjust the power levels of cell A to 63 dBV emf() and cell B to 45 dBV emf() so that the MS re-selects cell A. Wait 30 s. The following messages are sent and received on cell A.
12
SS -> MS
NOTIFICATION/NCH
with a different NLN from step C5, a valid channel description, a call reference active in the MS .
14
SS -> MS
SYSTEM INFORMATION TYPE 6
with the NLN(SACCH) same as step 12.
15
MS
wait 5 s. and check that the MS indicates the notification, MMI action to reject the new call.
18
SS -> MS
UPLINK FREE
19
MS
MMI action to request uplink access of the call.
20
MS -> SS
UPLINK ACCESS
21
MS -> SS
UPLINK ACCESS
22
SS -> MS
UPLINK BUSY
23
SS -> MS
VGCS UPLINK GRANT
Reference to step 21.
24
MS -> SS
TALKER INDICATION
L2: SABM / UA
25
MS
check that the TCH is through connected and the MS gives indication to the user.
26
SS -> MS
NOTIFICATION/NCH
with a different NLN from step 12, a valid channel description, a call reference active in the MS.
27
MS
check that the MS does not indicate the notification.
28
SS -> MS
SYSTEM INFORMATION TYPE 6
with the NLN (SACCH) same as step 26.
29
MS
wait 5 s. and check that the MS indicates the notification, MMI action to reject the new call.
30
SS -> MS
HANDOVER COMMAND
handover to cell B. The following messages are sent and received on cell B.
31
MS -> SS
HANDOVER ACCESS
32
MS -> SS
HANDOVER ACCESS
33
MS -> SS
HANDOVER ACCESS
34
MS -> SS
HANDOVER ACCESS
Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH
35
MS -> SS
SABM
Sent without information field.
36
SS -> MS
UA
37
MS -> SS
HANDOVER COMPLETE
38
MS
wait 1 second, for the MS receiving consecutively at least two identical NLN (NCH).
39
SS -> MS
NOTIFICATION/NCH
with an NLN different from those in step 12 and 26, a valid channel description, a call reference active in the MS.
41
SS -> MS
SYSTEM INFORMATION TYPE 6
with the NLN(SACCH) same as step 39.
42
MS
check that the MS indicates the notification. MMI action to reject the new call.
43
SS -> MS
UPLINK RELEASE
44
SS -> MS
CHANNEL RELEASE
The MS returns to idle mode. L2:DISC/UA.
Specific Message Contents
NOTIFICATION/NCH
Information Element
value/remark
NT/N Rest Octets
Reduced monitoring indication
'1'B, reduced monitoring
NLN (NCH)
as specified in the test step
PAGING REQUEST TYPE 1
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P1 Rest Octets
- NLN (PCH) indication
H
- NLN (PCH)
as specified in the test step
- NLN status
'0'B
- Priority 1 indication
L
- Priority 2 indication
L
- Group call information indication
L
- Spare padding
logic L
PAGING REQUEST TYPE 2
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P2 Rest Octets
- CN3 indication
L
- NLN (PCH) indication
H
- NLN (PCH)
as specified in the test step
- NLN status
'0'B
- Priority 1 indication
L
- Priority 2 indication
L
- Priority 3 indication
L
- Spare padding
logic L
PAGING REQUEST TYPE 3
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P3 Rest Octets
- CN3 indication
L
- NLN (PCH) indication
H
- NLN (PCH)
as specified in the test step
- Priority 1 indication
L
- Priority 2 indication
L
- Priority 3 indication
L
- Priority 4 indication
L
- NLN status indication
H
- NLN status
'0'B
- Spare padding
logic L
SYSTEM INFORMATION TYPE 6
Information Element
value/remark
S6 Rest Octets
7 octets length
- PCH/NCH info indication
H
- PCH/NCH info
- paging channel restructuring
0 (not restructured)
- NLN (SACCH)
as specified in the test step
- Call priority indication
'0'B, priority not included
- NLN status
'0'B
- VGCS/VBS options
- in-band notifications
H
- in-band paging
H
- Spare padding
logic L
HANDOVER COMMAND
Information Element
Value/remark
As default message contents, except:
Channel Description
- Channel type
TCH/F + ACCHs
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
Single RF channel
- ARFCN
GSM 900: 60
DCS 1 800: 830
PCS 1 900:730
GSM 450: 276
GSM 480: 323
GSM 710: 497
GSM 750: 497
T-GSM 810: 497
GSM 850: 187
Synchronisation Indication
Synchronised
VGCS target mode indication
Group transmit mode
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.4 VGCS-VBS / Notification / Limited Service state
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.4.1 Conformance requirement
|
In state MM IDLE and service state LIMITED SERVICE:
1. The MS shall indicate notifications to the GCC or BCC sub-layer for which a channel description has been received in the notification by the RR sub-layer.
2. The MS shall reject requests of the GCC or BCC sub-layer to respond to notifications for which no channel description has been received in the notification by the RR sub-layer.
3. The MS shall request the RR sub-layer to receive a voice group or broadcast call if the GCC or BCC sublayer requests the reception of a voice group or broadcast call for which a channel description has been received in the notification by the RR sublayer and then go to the service state RECEIVING GROUP CALL (LIMITED SERVICE).
4. The MS shall reject any request of establishing a group call.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.2.2.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.4.2 Test purpose
|
To verify that while in state MM IDLE and service state LIMITED SERVICE:
1. The MS rejects requests from user to respond to notifications for which no channel description has been received in the notification by the RR sub-layer.
2. The MS indicates notifications for which a channel description has been received in the notification.
3. The MS accepts user requests to respond to notifications for which channel description has been received in the notification and goes to the service state RECEIVING GROUP CALL (LIMITED SERVICE).
4. The MS rejects any request of establishing a group call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.1.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS, with SIM, is in MM-state "idle, limited service" because LA not allowed.
Specific PICS statements:
- Support VGCS originating (TSPC_AddInfo_VGCS_Originating)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate a call notification.
- Way to accept VGCS or VBS call.
- Way to initiate a normal VGCS/VBS call.
Foreseen Final State of the MS
"limited service" mode.
Test Procedure
The MS, with SIM, is in MM idle limited service state because LA is not allowed. The SS sends NOTIFICATION/NCH message containing call reference active in the MS but no VGCS/VBS channel description. It is checked that the MS indicates the notification and rejects the request of joining the notified call. The SS sends NOTIFICATION/NCH message containing call reference active in the MS and VGCS/VBS channel description. It is checked that the MS indicates the notification, and joins the notified call on request. If the MS supports VGCS/VBS originating, the MS is requested to initiate VGCS/VBS call. It is checked that the MS rejects the request.
Maximum Duration of Test
5 minutes.
Expected Sequence
Step
Direction
Message
Comments
0
MS
the MS is in MM idle mode limited service state
1
SS -> MS
NOTIFICATION/NCH
without VGCS/VBS channel description
2
MS
MMI action to request responding to the notification
3
MS
check that the MS rejects the request and that no RR connection establishment is attempted for 10s.
5
SS -> MS
NOTIFICATION/NCH
with VGCS/VBS channel description
6
MS
check that the MS indicates the notification
7
MS
MMI action to request to join the notification
8
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
9
SS -> MS
CHANNEL RELEASE
UI format
10
MS
If the MS supports VGCS/VBS originating MMI action to initiate a normal VGCS/VBS call
11
SS
check that the MS rejects the request and that no RR connection establishment is attempt.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2 VGCS-VBS / Paging
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.1 VGCS-VBS / Paging / Paging indication
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.1.1 Conformance requirement
|
1. Paging into on-going voice group calls shall be provided as an implementation option.
2. In group receive mode the MS shall be ready to receive paging information on the FACCH containing the mobile subscriber identity and the priority level if eMLPP applies.
3. In group transmit mode if the MS has received a paging message with the own mobile station identity on the PCH or on the voice group call channel downlink, the RR entity shall provide an indication to the upper layers, together with the related priority, if applicable.
4. In group transmit mode if the MS receives information on the voice group call channel of the existence of a paging message in its paging subgroup of the PCH, the RR entity shall pass this information to the upper layers together with the related priority.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.12, 9.1.21a, 3.4.15.1.2.4, 10.5.2.23, 10.5.2.24 and 10.5.2.25.
3GPP TS 03.68 subclause 11.3.1.3c.
3GPP TS 03.69 subclause 11.3.1.3c.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.1.2 Test purpose
|
It is checked that:
1. When the MS in group receive mode if a NOTIFICATION/FACCH message on the voice group call channel containing in-band paging information is received, the MS provides an indication with the correct priority if applicable.
2. When the MS in group receive mode if a paging message with the own mobile station identity on PCH is received, it provides an indication with the correct priority.
3. When the MS in group transmit mode if a NOTIFICATION/FACCH message on the voice group call channel containing in-band paging information is received, the MS provides an indication with the correct priority.
4. If the MS in group transmit mode if a paging message with the own mobile station identity on PCH is received, it provides an indication with the correct priority.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
No automatic answering configured.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
- Support eMLPP (TSPC_Serv_eMLPP)
- Support monitoring on PCH in group transmit mode (TSPC_AddInfo_MonitorPCH_GroupTransmitMode)
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to request uplink.
Foreseen Final State of the MS
"Idle, updated".
Test Procedure
The MS is in group receive mode. The SS sends NOTIFICATION/FACCH message containing Paging Information IE which addresses the MS. It is checked that the MS indicates the paging information.
The SS changes SI 6 indicating no support of in-band paging. After waiting 5 s. the SS sends a PAGING REQUEST TYPE 1 message addressing the MS on the paging sub-channel of the MS. It is checked that the MS indicates the paging information, together with the priority level if it supports eMLPP. The test procedure is repeated for sending PAGING REQUEST TYPE 2 and PAGING REQUEST TYPE 3 messages.
The same test procedure is repeated for the MS in group transmit mode if supporting VGCS talking or VBS originating.
Maximum Duration of Test
5 minutes.
Expected Sequence
If the MS mode supports VGCS talking or VBS originating the test sequence is repeated once for k=2. If the MS supports monitoring PCH in group transmit mode steps 5 - 17 for k=2 are executed.
Step
Direction
Message
Comments
0
SS
broadcast the default SIs.
A1
MS
for k=1, the MS is brought in group receive mode.
B1
for k=2, the MS is in brought group transmit mode.
2
SS -> MS
NOTIFICATION/FACCH
In-band paging Information addresses the MS.
3
MS
check that the MS indicates correctly the paging information of a new MT call with priority 4 if the MS supports eMLPP.
4
MS
user action to reject the point-to-point MT call.
5
SS -> MS
SYSTEM INFORMATION TYPE 6
indicating no in-band paging on FACCH
6
SS
wait 5s.
7
SS -> MS
PAGING REQUEST TYPE 1
with priority 2
8
MS
check that the MS indicates correctly the paging information of a new MT call with the priority if the MS supports eMLPP.
9
MS
user action to reject the incoming call.
10
SS
wait 5 s.
11
SS -> MS
PAGING REQUEST TYPE 2
with priority 3
12
MS
check that the MS indicates correctly the paging information of a new MT call with the priority if the MS supports eMLPP.
13
MS
user action to reject the incoming call.
14
SS
wait 5s.
15
SS -> MS
PAGING REQUEST TYPE 3
no priority
16
MS
check that the MS indicates correctly the paging information of a new MT call which no priority is provided to.
17
MS
user action to reject the incoming call.
A18
for k=1, no signalling
B18
SS -> MS
UPLINK RELEASE
for k=2, return to group receive mode. Only for a VGCS call.
19
SS -> MS
CHANNEL RELEASE
UI format, the MS returns to idle updated state. For (k=1) and (k=2 in case of VGCS call).
20
SS -> MS
CHANNEL RELEASE
For k=2, for a VBS call, the MS returns to idle mode. L2:DISC/UA.
Specific Message Contents
NOTIFICATION/FACCH - in step 2
Information Element
value/remark
Group call / Paging information indication
'1', paging information
Paging Information
- mobility identity
TMSI previously allocated to MS
- channel first
'10'B, TCH/F
eMLPP priority indication
'1'B
- priority
'001'B, call priority level 4
spare padding
logic L
SYSTEM INFORMATION TYPE 6 - in step 5
Information Element
value/remark
S6 Rest Octets
7 octets length
- PCH/NCH info indication
L
- VGCS/VBS options
- in-band notifications
H
- in-band paging
L
- Spare padding
logic L
PAGING REQUEST TYPE 1 - in step 7
Information Element
value/remark
P1 Rest Octets
- NLN (PCH) indication
L
- Priority 1 indication
H
- Priority
'011'B, level 2
- Spare padding
logic L
PAGING REQUEST TYPE 2 - in step 11
Information Element
value/remark
P2 Rest Octets
- CN3 indication
L
- NLN (PCH) indication
L
- Priority 1 indication
H
- Priority
'010'B, level 3
- Spare padding
logic L
PAGING REQUEST TYPE 3 - in step 15
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P3 Rest Octets
- CN3 indication
L
- NLN (PCH) indication
L
- Priority 1 indication
H
- Priority
'000'B, no level applied
- Spare padding
logic L
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.2 VGCS-VBS / Paging / Notification
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.2.1 Conformance requirement
|
A PAGING REQUEST TYPE 1 message may have an additional notification coded in the P1 rest octets information element. It allows to notify the mobile an emergency group or broadcast call even when the MS at the moment does not monitor the NCH channel.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.2.1, 3.3.3.1 and 10.5.2.23.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.2.2 Test purposes
|
To verify that:
1. the MS in idle mode indicates correctly an incoming broadcast or group call when having received a PAGING REQUEST TYPE 1 message whose P1 rest octets information element contains group call information addressing the MS.
2. the MS in group receive mode indicates correctly an incoming broadcast or group call when having received a PAGING REQUEST TYPE 1 message whose P1 rest octets information element contains group call information addressing the MS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.2.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell with default parameters for ASCI testing.
Mobile Station:
The MS is in MM-state "idle, updated" with a TMSI allocated.
Specific PICS statements:
- Support VGCS talking (TSPC_AddInfo_VGCS_Talking)
- Support VBS originating (TSPC_AddInfo_VBS_Originating)
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to indicate a call notification.
- Way to accept a VGCS or VBS.
- Way to verify the downlink speech path.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is in idle mode. The SS sends in the NCH block only access grant messages. The SS sends a PAGING REQUEST TYPE 1 message on the paging sub-channel of the MS. The Mobile Identity in the message does not address the MS. The P1 rest octets in the message contains VGCS/VBS channel description and VGCS/VBS call reference not active in the MS. It is checked that the MS ignores the paging message. Similarly, the SS sends again the PAGING REQUEST TYPE 1 message on the paging sub-channel of the MS, not addressing the MS. The message contains VGCS/VBS channel description and VGCS/VBS call reference active in the MS. It is checked that the MS indicates correctly the notified group call reference(s) and joins VGCS/VBS call on request of responding to the notification. The group call is terminated. The SS sends PAGING REQUEST TYPE 1 message on the paging sub-channel of the MS which contains the "good reference" but no VGCS/VBS channel description. The Mobile Identity in the message does not address the MS. It is checked that the MS indicates correctly the notified group call reference(s) and establishes a RR connection to respond to the notification on request of responding to the call, then joins the call. The group call is terminated.
The initial conditions for SS are set to the same as ASCI default. The MS is brought to group receive mode the test procedure is repeated once.
Maximum Duration of Test
5 minutes.
Expected Sequence
Test steps 0 to 19 are executed for k=1, 2.
Step
Direction
Message
Comments
A0
SS
For k = 1, the initial conditions for SS are same as ASCI default, except the NCH block containing only access grant messages.
A1
MS
the MS is in idle mode.
B0
SS
For k = 2, the initial conditions for SS are same as ASCI default, except the NCH block containing only access grant messages.
B1
MS
the MS is brought in group receive mode
2
SS -> MS
PAGING REQUEST TYPE 1
with a description of VGCS/VBS channel and a VGCS/VBS call reference not active in the MS
3
MS
check that the MS ignores the notification and there is no uplink transmission on that channel for 10 s.
4
SS -> MS
PAGING REQUEST TYPE 1
with a description of VGCS/VBS channel and a VGCS/VBS call reference active in the MS
5
MS
check that the MS gives an indication containing the notified group call reference
6
MS
MMI action to join the VGCS/VBS call
7
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
8
SS -> MS
CHANNEL RELEASE
UI format, return to the idle updated state
9
SS
wait 5s.
10
SS -> MS
PAGING REQUEST TYPE 1
with a VGCS/VBS call reference active in the MS but no VGCS/VBS channel description
11
MS
check that the MS gives an indication containing the notified group call reference
A12
MS
For k = 1, MMI action to join the VGCS/VBS call
A13
MS -> SS
CHANNEL REQUEST
A14
SS -> MS
IMMEDIATE ASSIGNMENT
A15
MS -> SS
NOTIFICATION RESPONSE
L2: SABM / UA
A16
SS -> MS
CHANNEL RELEASE
release the dedicated channel. The MS releases L2 multiple frame link L2:DISC/UA.
A17
MS
check that the TCH in downlink is through connected and there is no uplink transmission on that channel for 10 s.
B12
SS
For k = 2, MMI action to reject the new VGCS/VBS call
18
SS -> MS
CHANNEL RELEASE
UI format, to return to idle updated state
19
wait 5s.
Specific Message Contents
PAGING REQUEST TYPE 1 - in steps 2
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P1 Rest Octets
- NLN (PCH) indication
L
- Priority 1 indication
L
- Priority 2 indication
L
- NLN status indication
L
- Group call information indication
H
- Group or broadcast call reference
not active in the SIM
- SF
VBS if only VBS supported, otherwise VGCS
- AF
'0'B, acknowledgement not required
- priority
4
- Ciphering information
No ciphering
Group Channel Description indication
'1', group channel description
Channel Description
24 bits
- Channel type and TDMA offset
TCH/FS
- Timeslot number
arbitrarily chosen, but not 0
- TSC
arbitrarily chosen
- Hopping
Single RF, non hopping channel
- ARFCN
GSM 450: 279
GSM 480: 326
GSM 900: 70
DCS 1 800: 850
PCS 1 900: 750
GSM: 475
GSM 750: 475
T-GSM 810: 475
GSM 850: 197
MA or FSL
'0'B, non hopping
Spare padding
logic L
PAGING REQUEST TYPE 1 - in steps 4
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P1 Rest Octets
- NLN (PCH) indication
L
- Priority 1 indication
L
- Priority 2 indication
L
- NLN status indication
L
- Group call information indication
H
- Group or broadcast call reference
PICS/PIXIT (27 bits), active in the SIM
- SF
VBS if only VBS supported, otherwise VGCS
- AF
'0'B, acknowledgement not required
- priority
4
- Ciphering information
No ciphering
Group Channel Description indication
'1', group channel description
Channel Description
24 bits
- Channel type and TDMA offset
TCH/FS
- Timeslot number
arbitrarily chosen, but not 0
- TSC
arbitrarily chosen
- Hopping
Single RF, non hopping channel
- ARFCN
GSM 450: 279
GSM 480: 326
GSM 900: 70
DCS 1 800: 850
PCS 1 900: 750
GSM: 475
GSM 750: 475
T-GSM 810: 475
GSM 850: 197
MA or FSL
'0'B, non hopping
Spare padding
logic L
PAGING REQUEST TYPE 1 - in steps 10
Information Element
value/remark
Mobile Identity 1
TMSI not allocated to MS
P1 Rest Octets
- NLN (PCH) indication
L
- Priority 1 indication
L
- Priority 2 indication
L
- NLN status indication
L
- Group call information indication
H
- Group or broadcast call reference
PICS/PIXIT (27 bits), active in the SIM
- SF
VBS if only VBS supported, otherwise VGCS
- AF
'0'B, acknowledgement not required
- priority
4
- Ciphering information
No ciphering
Group Channel Description indication
'0', no group channel description
Spare padding
logic L
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3 VGCS-VBS / RR Procedures
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.1 VGCS-VBS / RR Procedures / frequency redefinition
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.1.1 Conformance requirements
|
The MS, after receiving a FREQUENCY REDEFINITION message in group transmit mode, shall start using the new frequencies and hopping sequence in the correct time slot.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.1.2 Test purpose
|
To verify that after receiving a FREQUENCY REDEFINITION message in group transmit mode, the MS starts using the new frequencies and hopping sequence at the time indicated in the message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, CCCH_CONF set to 1 basic physical channel used for CCCH, not combined with SDCCHs. The cell allocation is set to CA450(1), CA480(1), CAPGSM(1), CADCS(1), CAPCS(1), CA710(1), CA750(1), CA810(1) or CA850(1), depending on the band of operation of the Mobile Station (See PICS/PIXIT), before each execution of this test.
Mobile Station:
The MS is in group transmit mode.
Specific PICS statements:
-
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to accept a VGCS or VBS.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
Test parameters:
An arbitrary value T in the range 92,...,29999 is chosen.
GSM 450:
Ca450(1) is set to 32.
An arbitrary subset CA450(1) of the set {259,...,293} containing ca450(1) elements is drawn.
An element B of the set CA450(1) is arbitrarily chosen.
An arbitrary value ca450(2) in the range 17,...,31 is chosen.
An arbitrary subset CA450(2) of the set {259,...,293} with ca450(2) elements and containing B is chosen.
For j = 1,2, values ma450(j) in the range j,...,ca450(j)‑1 and values MAIO450(j) in the range 0,...,ma450(j)‑1 are arbitrarily chosen.
Subsets MA450(j) of CA450(j) not containing B and having ma(j) elements are arbitrarily chosen.
GSM 480:
Ca480(1) is set to 32.
An arbitrary subset CA480(1) of the set {306,...,340} containing ca480(1) elements is drawn.
An element B of the set CA480(1) is arbitrarily chosen.
An arbitrary value ca480(2) in the range 17,...,31 is chosen.
An arbitrary subset CA480(2) of the set {306,...,340} with ca480(2) elements and containing B is chosen.
For j = 1,2, values ma480(j) in the range j,...,ca480(j)‑1 and values MAIO480(j) in the range 0,...,ma480(j)‑1 are arbitrarily chosen.
Subsets MA480(j) of CA480(j) not containing B and having ma(j) elements are arbitrarily chosen.
GSM 900:
caPGSM(1) is set to 64.
An arbitrary subset CAPGSM(1) of the set {1,...,124} containing caPGSM(1) elements is drawn.
An element B of the set CAPGSM(1) is arbitrarily chosen.
An arbitrary value caPGSM(2) in the range 20,...,63 is chosen.
An arbitrary subset CAPGSM(2) of the set {1,...,124} with caPGSM(2) elements and containing B is chosen.
For j = 1,2, values maPGSM(j) in the range j,...,caPGSM(j)‑1 and values MAIOPGSM(j) in the range 0,...,maPGSM(j)‑1 are arbitrarily chosen.
Subsets MAPGSM(j) of CAPGSM(j) not containing B and having ma(j) elements are arbitrarily chosen.
DCS 1 800:
caDCS(1) is set to 64.
An arbitrary subset CADCS(1) of the set {700,...,812} containing caDCS(1) elements is chosen.
An element B of the set CADCS(1) is arbitrarily chosen. CADCS(1) is then coded using the Variable Bit Map coding scheme.
An arbitrary value caDCS(2) in the range 17,...,63 is chosen.
An arbitrary subset CADCS(2) of the set {700,...,812} with caDCS(2) elements and containing B is chosen. CADCS(2) is then coded using the Variable Bit Map coding scheme.
For j = 1,2, values maDCS(j) in the range j,...,caDCS(j)‑1 and values MAIODCS(j) in the range 0,...,maDCS(j)‑1 are arbitrarily chosen.
Subsets MADCS(j) of CADCS(j) not containing B and having maDCS(j) elements are arbitrarily chosen.
PCS 1 900:
caPCS(1) is set to 64.
An arbitrary subset CAPCS(1) of the set {700,...,812} containing caPCS(1) elements is chosen.
An element B of the set CAPCS(1) is arbitrarily chosen. CAPCS(1) is then coded using the Variable Bit Map coding scheme.
An arbitrary value caPCS(2) in the range 17,...,63 is chosen.
An arbitrary subset CAPCS(2) of the set {700,...,812} with caPCS(2) elements and containing B is chosen. CAPCS(2) is then coded using the Variable Bit Map coding scheme.
For j = 1,2, values maPCS(j) in the range j,...,caPCS(j)‑1 and values MAIOPCS(j) in the range 0,...,maPCS(j)‑1 are arbitrarily chosen.
Subsets MAPCS(j) of CAPCS(j) not containing B and having maPCS(j) elements are arbitrarily chosen.
GSM 710:
ca 710(1) is set to 64.
An arbitrary subset CA 710(1) of the set {438,...,511} containing ca710(1) elements is drawn.
An element B of the set CA710(1) is arbitrarily chosen.
An arbitrary value ca710(2) in the range 457,...,500 is chosen.
An arbitrary subset CA710(2) of the set {438,...,511} with ca710(2) elements and containing B is chosen.
For j = 1,2, values ma710(j) in the range j,...,ca710(j)‑1 and values MAIO710(j) in the range 0,...,ma710(j)‑1 are arbitrarily chosen.
Subsets MA710(j) of CA710(j) not containing B and having ma(j) elements are arbitrarily chosen.
GSM 750:
ca750(1) is set to 64.
An arbitrary subset CA750(1) of the set {438,...,511} containing ca750(1) elements is drawn.
An element B of the set CA750(1) is arbitrarily chosen.
An arbitrary value ca750(2) in the range 457,...,500 is chosen.
An arbitrary subset CA750(2) of the set {438,...,511} with ca750(2) elements and containing B is chosen.
For j = 1,2, values ma750(j) in the range j,...,ca750(j)‑1 and values MAIO750(j) in the range 0,...,ma750(j)‑1 are arbitrarily chosen.
Subsets MA750(j) of CA750(j) not containing B and having ma(j) elements are arbitrarily chosen.
T-GSM 810:
ca810(1) is set to 64.
An arbitrary subset CA810(1) of the set {438,...,511} containing ca810(1) elements is drawn.
An element B of the set CA810(1) is arbitrarily chosen.
An arbitrary value ca810(2) in the range 457,...,500 is chosen.
An arbitrary subset CA810(2) of the set {438,...,511} with ca810(2) elements and containing B is chosen.
For j = 1,2, values ma810(j) in the range j,...,ca810(j)‑1 and values MAIO810(j) in the range 0,...,ma810(j)‑1 are arbitrarily chosen.
Subsets MA810(j) of CA810(j) not containing B and having ma(j) elements are arbitrarily chosen.
GSM 850:
ca850(1) is set to 64.
An arbitrary subset CA850(1) of the set {128,...,251} containing ca850(1) elements is drawn.
An element B of the set CA850(1) is arbitrarily chosen.
An arbitrary value ca850(2) in the range 147,...,200 is chosen.
An arbitrary subset CA850(2) of the set {128,...,251} with ca850(2) elements and containing B is chosen.
For j = 1,2, values ma850(j) in the range j,...,ca850(j)‑1 and values MAIO850(j) in the range 0,...,ma850(j)‑1 are arbitrarily chosen.
Subsets MA850(j) of CA850(j) not containing B and having ma(j) elements are arbitrarily chosen.
The MS is brought into group transmit mode. The SS sends a FREQUENCY REDEFINITION message. It is checked that the MS uses the new frequencies/hopping sequence at the TDMA frame defined by the contents of the "Starting Time" information element. (The range for T ensures that the MS does not start transmission on the new frequencies until the designated frame.)
The check is performed at the RF burst level. The SS checks the received pattern with the expected pattern, and the SS checks for each burst whether the burst is transmitted at the right frequency.
Maximum Duration of Test
T + 7
Expected Sequence
Step
Direction
Message
Comments
1
MS
the MS is in group transmit mode using full rate on an RF hopping channel
9
SS -> MS
FREQUENCY REDEFINITION
see description 1 below.
10
MS
check that the MS uses the new frequencies in the correct frame.
11
SS -> MS
FREQUENCY REDEFINITION
see description 2 below.
12
MS
check that the MS uses the new frequencies in the correct frame.
13
SS -> MS
CHANNEL RELEASE
The MS releases L2 multiple frame link L2:DISC/UA.
Specific Message Contents
FREQUENCY REDEFINITION (Description 1)
Information Element
value/remark
as default except:
Channel Description
- Channel type
TCH/FS
and TDMA offset
- Timeslot number
not changed
- TSC
not changed
- Hopping channel
RF hopping channel
- MAIO
GSM 450: MAIO450(1)
GSM 480: MAIO480(1)
GSM 710: MAIO710(1)
GSM 750: MAIO750(1)
T-GSM 810: MAIO810(1)
GSM 850: MAIO850(1)
GSM 900: MAIOPGSM(1)
DCS 1 800: MAIODCS(1)
PCS 1 900: MAIOPCS(1)
- HSN
0
Mobile Allocation
GSM 450: corresponds to set MA450(1)
GSM 480: corresponds to set MAIO480(1)
GSM 710: corresponds to set MAIO710(1)
GSM 750: corresponds to set MAIO750(1)
T-GSM 810: corresponds to set MAIO810(1)
GSM 850: corresponds to set MAIO850(1)
GSM 900: corresponds to set MAIOPGSM(1)
DCS 1 800: corresponds to set MAIODCS(1)
PCS 1 900: corresponds to set MAIOPCS(1)
Starting Time
The last burst of the first L2 frame containing the beginning of this message is transmitted in frame number X. The starting time is set to frame number (X plus T modulo 42 432).
Cell Channel Description
- Information element identifier
62H
- contents
GSM 450: corresponds to set CA450(1) with "Format ID" set to "Range 128".
GSM 480: corresponds to set CA480(1) with "Format ID" set to "Range 128".
GSM 710: corresponds to set CA710(1) with "Format ID" set to "bit map 0".
GSM 750: corresponds to set CA750(1) with "Format ID" set to "bit map 0".
T-GSM 810: corresponds to set CA810(1) with "Format ID" set to "bit map 0".
GSM 850: corresponds to set CA850(1) with "Format ID" set to "128 range".
GSM 900: corresponds to set CAPGSM(1) with "Format ID" set to "bit map 0".
DCS 1 800: corresponds to set CADCS(1) with "Format ID" set to " Variable Bit Map"
PCS 1 900: corresponds to set CAPCS(1) with "Format ID" set to " Variable Bit Map"
FREQUENCY REDEFINITION (Description 2)
Information Element
value/remark
as default except:
Channel Description
- Channel type
TCH/FS
and TDMA offset
- Timeslot number
not changed
- TSC
not changed
- Hopping channel
RF hopping channel
- MAIO
GSM 450: MAIO450(2)
GSM 480: MAIO480(2)
GSM 710: MAIO710(2)
GSM 750: MAIO750(2)
T-GSM 810: MAIO810(2)
GSM 850: MAIO850(2)
GSM 900: MAIOPGSM(2)
DCS 1 800: MAIODCS(2)
PCS 1 900: MAIOPCS(2)
- HSN
0
Mobile Allocation
GSM 450: corresponds to set MA450(2)
GSM 480: corresponds to set MAIO480(2)
GSM 710: corresponds to set MAIO710(2)
GSM 750: corresponds to set MAIO750(2)
T-GSM 810: corresponds to set MAIO810(2)
GSM 850: corresponds to set MAIO850(2)
GSM 900: corresponds to set MAIOPGSM(2)
DCS 1 800: corresponds to set MAIODCS(2)
PCS 1 900: corresponds to set MAIOPCS(2)
Starting Time
The last burst of the first L2 frame containing the beginning of this message is transmitted in frame number X. The starting time is set to frame number (X plus T modulo 42 432).
Cell Channel Description
- Information element identifier
62H
- contents
GSM 450: corresponds to set CA450(2) with "Format ID" set to "Range 128".
GSM 480: corresponds to set CA480(2) with "Format ID" set to "Range 128".
GSM 710: corresponds to set CA710(2) with "Format ID" set to "bit map 0".
GSM 750: corresponds to set CA750(2) with "Format ID" set to "bit map 0".
T-GSM 810: corresponds to set CA810(2) with "Format ID" set to "bit map 0".
GSM 850: Corresponds to set CA850(2) with "Format ID" set to "128 range".
GSM 900: corresponds to set CAPGSM(2) with "Format ID" set to "bit map 0".
DCS 1 800: corresponds to set CADCS(2) with "Format ID" set to " Variable Bit Map"
PCS 1 900: corresponds to set CAPCS(2) with "Format ID" set to " Variable Bit Map"
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.2 VGCS-VBS / RR Procedures / assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.2.1 Conformance requirements
|
1. Upon receipt of the ASSIGNMENT COMMAND message in group transmit mode, the mobile station shall initiate a local end release of link layer connections, disconnect the physical channels, command the switching to the assigned channels and initiate the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the main signalling links).
2. MM-messages and CM-messages using SAPI=0 sent from the mobile station to the network shall be duplicated by the data link layer in the following case:
A channel change of dedicated channels is required (assignment or handover procedure) and the last layer 2 frame has not been acknowledged by the peer data link layer before the mobile station leaves the old channel.
In this case, the mobile station does not know whether the network has received the message correctly. Therefore, the mobile station shall send the message again after the new dedicated channel is established.
3. An ASSIGNMENT COMMAND message may indicate a frequency change in progress, with a starting time and possibly alternative channel descriptions.
In the case of the reception of an ASSIGNMENT COMMAND message which contains only the description of a channel to be used after the starting time, and if the starting time has not already elapsed, the mobile station shall wait up to the starting time before accessing the channel.
4. The MS shall apply the hopping frequencies specified in ASSIGNMENT COMMAND message in the Mobile Allocation IE or the Frequency List IE at the time of accessing the new channel using the last received Cell Allocation.
5. After receipt of the ASSIGNMENT COMMAND the MS shall perform the assignment and return an ASSIGNMENT COMPLETE without undue delay.
6. On the mobile station side, if a lower layer failure happens on the new channel before the ASSIGNMENT COMPLETE message has been sent, the mobile station deactivates the new channels, reactivates the old channels, reconnects the TCHs if any and triggers the establishment of the main signalling link. It then sends a ASSIGNMENT FAILURE message, cause "protocol error unspecified" on the main DCCH and resumes the normal operation, as if no assignment attempt had occurred. The operational parameters (e.g. ciphering mode) when returning on the old channel are those applied before the procedure.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.1.4.3, 3.4.3 and 3.4.3.3.
3GPP TS 04.13 subclause 5.2.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.2.2 Test purpose
|
1. To verify that upon receipt of an ASSIGNMENT COMMAND in group transmit mode, the MS switches to the channel defined in the ASSIGNMENT COMMAND, establishes the link and sends an ASSIGNMENT COMPLETE message.
1.1 from non-hopping TCH/F to hopping TCH/F using a different timeslot;
1.2 from hopping TCH/F to non-hopping TCH/F using a different timeslot.
2. To verify that the MS, supporting TCH, having sent an MM- or CM message which was not acknowledged on L2 before the channel assignment procedure was initiated and before the MS has left the old channel, repeats that message after completion of the assignment procedure without incrementing N(SD). This is tested in the special case of MM message AUTHENTICATION RESPONSE.
3. To verify that, if the MS has received an ASSIGNMENT COMMAND message which contains only the description of a channel to be used after the starting time, and if the starting time has not already elapsed, the mobile station waits up to the starting time before accessing the channel.
4. To verify that the MS having received an ASSIGNMENT COMMAND, correctly decodes the Mobile Allocation and Frequency List IEs for frequency hopping and applies the specified frequencies using the correct Cell Allocation.
5. To verify that after receipt of the ASSIGNMENT COMMAND the MS returns an ASSIGNMENT COMPLETE without undue delay.
6. To test that, when the MS fails to seize the new channel, the MS reactivates the old channel.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters except:
Band
BCCH ARFCN
Throughout the test, the CA broadcast in System Information 1 is
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324
GSM 710
457
447, 454, 457, 463, 471, 479, 482, 483, 489, 496
GSM 750
457
447, 454, 457, 463, 471, 479, 482, 483, 489, 496
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482, 483, 489, 496
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59
DCS 1 800
747
734, 741, 747, 754, 759, 766, 773, 775, 779, 782
PCS 1 900
647
634, 641, 647, 654, 659, 666, 673, 675, 679, 682
Note that the actual CA of the cell contains other frequencies.
Mobile Station:
The MS is in group transmit mode.
Specific PICS statements:
-
PIXIT Statements:
- Way to configure VGCS or VBS.
- Way to initiate a VBS call.
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is brought into group transmit mode. A hopping channel is assigned with ASSIGNMENT COMMAND, which includes a Starting Time IE. It is checked that the MS switches to the assigned channel at the time specified in Starting Time IE, establishes the link and sends an ASSIGNMENT COMPLETE message.
Then the SS sends a AUTHENTICATION REQUEST message. The MS shall answer with an AUTHENTICATION RESPONSE message, which is not acknowledged on L2 by the SS. Immediately after the AUTHENTICATION RESPONSE message is received, the SS sends an ASSIGNMENT COMMAND. It is checked that the MS switches to the assigned channel, establishes the link with the commanded power level, sends as ASSIGNMENT COMPLETE message and then MS repeats the AUTHENTICATION RESPONSE message, with the same N(SD) value.
Then the SS sends an ASSIGNMENT COMMAND, but the SS does not activate the specified new channel. It is checked that the MS re-establishes the old channel and sends ASSIGNMENT FALIURE message on the old channel.
Maximum Duration of Test
30 s.
Expected Sequence
Step
Direction
Message
Comments
1
MS
the MS is in group transmit mode.
2
SS -> MS
ASSIGNMENT COMMAND
See specific message contents.
3
MS -> SS
ASSIGNMENT COMPLETE
Sent on the correct channel after establishment of the main signalling link. This message shall be ready to be transmitted before 600 ms after the completion of step 2.
4
SS
The SS checks that the MS reports the requested power level in the layer 1 header of the SACCH message that is sent in the first SACCH multiframe following the SABM.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
This message is not L2 acknowledged by the SS.
7
SS -> MS
ASSIGNMENT COMMAND
See specific message contents.
8
MS -> SS
ASSIGNMENT COMPLETE
Sent on the correct channel after establishment of the main signalling link. This message shall be ready to be transmitted before 600 ms after the completion of step 7.
9
MS -> SS
AUTHENTICATION RESPONSE
N(SD) shall be the same as in step 6.
10
SS -> MS
ASSIGNMENT COMMAND
See specific message contents, the SS does not activate the new channel. The MS attempts (and fails) to establish a signalling link on the new channel.
11
MS
The MS re-establishes the signalling link on the old channel.
12
MS -> SS
ASSIGNMENT FAILURE
RR cause value = "protocol error unspecified".
13
SS -> MS
UPLINK RELEASE
14
SS -> MS
CHANNEL RELEASE
UI format, the main signalling link is released.
Specific Message Contents
ASSIGNMENT COMMAND - step 2
Channel Description
- Channel Type and TDMA offset
TCH/F
- Timeslot Number
(N+1) mod 8
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1) where N is the number of frequencies in the Mobile Allocation IE.
- HSN
Chosen arbitrarily from the set (1 to 63)
Power Command
- Power level
Chosen arbitrarily but with a changed value.
Frequency list IE
Not included
Channel Mode
- Mode
A speech mode arbitrarily chosen from the full rate capabilities declared for the MS
Mobile Allocation
Indicates all of the CA (broadcast on the BCCH) except for the BCCH carrier.
Starting Time
indicates (current frame number + 100 frames) mod 42432
VGCS target mode Indication
- Target mode
group transmit mode
- Group cipher key number
no ciphering
ASSIGNMENT COMMAND - step 7
Channel Description
- Channel Type and TDMA offset
TCH/F
- Timeslot Number
(N+3) mod 8
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF Channel
- ARFCN
the ARFCN of the BCCH carrier
Power Command
- Power level
Chosen arbitrarily but with a changed value.
Channel Mode
A speech mode arbitrarily chosen from the full rate capabilities declared for the MS
Frequency list IE
Not Included
Cell Channel Description
GSM 450: range 128 encoding (271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
GSM 480: range 128 encoding (318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338)
GSM 900: bit map zero encoding (45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
DCS 1 800: range 128 encoding (773, 775, 779, 782, 791, 798, 829, 832, 844)
PCS 1 900: range 128 encoding (673, 675, 679, 682, 691, 698, 729, 732, 744)
GSM 710: 128 range encoding (482, 483, 489, 496, 498, 500, 501, 502, 503, 506, 508)
GSM 750: 128 range encoding (482, 483, 489, 496, 498, 500, 501, 502, 503, 506, 508)
T-GSM 810: 128 range encoding (482, 483, 489, 496, 498, 500, 501, 502, 503, 506, 508)
GSM 850: 128 range encoding (172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241)
Mobile Allocation
Not included
Starting Time
Not included
VGCS target mode Indication
Not included
ASSIGNMENT COMMAND - step 10
Channel Description
- Channel Type and TDMA offset
TCH/F
- Timeslot Number
(N+2) mod 8
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF Channel
- ARFCN
The ARFCN of the BCCH carrier
Power Command
- Power level
Chosen arbitrarily but with a changed value.
Channel Mode
A speech mode arbitrarily chosen from the full rate capabilities declared for the MS
Frequency list IE
Not included
Cell Channel Description
Not included
Mobile Allocation
Not included
Starting Time
Not included
VGCS target mode Indication
- Target mode
group transmit mode
- Group cipher key number
no ciphering
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.3 VGCS-VBS / RR Procedures / handover / successful in group transmit mode
|
This clause deals with signalling tests in non-synchronised handover in successful case.
Table 26.14.3.3.1 contains a summary of the different combinations of parameters which have to be tested. For execution counter=3, the target channel is dedicated mode.
Table 26.14.3.3.1
From
To
Timing Adv.
Start
Time
Sync
?
State
of call
Exec
Counter
TCH/F, no FH
TCH/F, no FH
20
1,1s
no
group trans. mode
1
TCH/F, no FH
TCH/F, FH
arbitrary
none
no
group trans. mode
2
TCH/F, FH
TCH/F, no FH
20
none
no
group trans. mode
3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.14.3.3.1 Conformance requirements
|
The MS shall correctly apply the handover procedure in the non-synchronised case when in group call transmit mode and when handover is performed from a traffic channel with/without frequency hopping towards a traffic channel with/without frequency hopping.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.4.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.