hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.1 Structured procedures / general
|
The purpose of these tests is to verify that the MS performs certain elementary procedures of the RR, MM, and CC protocol correctly within a structured procedure. The term "structured procedure" is defined in 3GPP TS 04.08 / 3GPP TS 23.108, clause 7, where also examples of structured procedures are given.
The reason for this test purposes is twofold:
- The behaviour of the MS in an elementary procedure may depend on the preamble which precedes the elementary procedure.
- Structured procedures tested in this subclause are used in other parts of this Technical Specification as preambles to establish the initial conditions for other tests; correct behaviour of an implementation under test in a preamble is essential for the validity of a test.
Mobile originating and terminating calls are tested in cases of both early and late assignment of the traffic channel; in one of the cases call release initiated by the network is tested, in another one, call release initiated by the MS.
The feature Directed Retry is tested in both Mobile Originated and Mobile Terminated Call. The configuration of the assigned channels is described in table 26.9-1:
Table 26.9-1
Directed Retry from
To
Call direction
Start Time
Sync.
Subclause
Exec. Counter
SDCCH/4
TCH/F, cycl. FH
MOC
None
No
26.9.7
1
SDCCH/8, cycl. FH
TCH/H, rand. FH
MOC
None
No
26.9.7
2
SDCCH/4
TCH/F, no FH
MTC
None
No
26.9.8
1
SDCCH/8, rand. FH
TCH/H, cycl. FH
MTC
1.1 sec.
No
26.9.8
2
The tests in this subclause only cover the successful outcome of elementary procedures (i.e. they do not deal with abnormal cases).
In this subclause, the emergency call service is tested for mobile stations that do not support the full rate speech version 2 in the following cases:
- emergency call initiated in the idle, updated state with authentication and ciphering, for speech full rate version 1 and if supported, speech half rate version 1;
- emergency call initiated in the idle, no IMSI state (hence without authentication and without ciphering), the network accepting the call, for either speech full rate version 1 or, provided it is supported, speech half rate version 1;
- emergency call initiated in the idle, no IMSI state (hence without authentication and without ciphering), the network rejecting the call, for either speech full rate version 1 or, provided it is supported, speech half rate version 1.
These tests on emergency calls are only applicable to an MS supporting speech.
For an MS supporting speech the test procedures in 26.9.2, 26.9.3, 26.9.4, 26.9.5, 26.9.7 and 26.9.8 are performed for speech (teleservice 11, telephony), once for speech full rate version 1 and, if supported, once for speech half rate version 1.
For an MS not supporting speech but supporting at least one teleservice, for each of the test procedures in subclauses 26.9.2, 26.9.3, 26.9.4, 26.9.5, 26.9.7 and 26.9.8 and each supported rate (full rate/half rate) a teleservice supported by the MS (see PICS/PIXIT statement) is chosen, and the test is performed corresponding to that teleservice (note that this teleservice is never a dual service).
In cases where a mobile originated call for the tested teleservice can be initiated both
- via the MMI; and
- via the R or S interface,
procedures 26.9.2 and 26.9.7 (m = 1) shall be performed when initiating the mobile originated call via the MMI and procedures 26.9.3 and 26.9.7 (m = 2) shall be performed when initiating the mobile originated call via an appropriate interface (R or S).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.2 Structured procedures / MS originated call / early assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.2.1 Conformance requirements
|
1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.
2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.
3) Subsequently after establishment of an MM connection, the MS shall send a SETUP message with correct parameters.
4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
- attach the user connection to the radio path;
- return a CONNECT ACKNOWLEDGE message.
5) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.
6) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.
References
Conformance requirement 1: 3GPP TS 02.07.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.1.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.6.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.4.4.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.13.1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.2.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.
2) To verify that the MS in MM state "idle, updated" and in RR idle mode, with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
3) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed the authentication and cipher mode setting procedures, the MS sends a SETUP message with correct parameters.
4) To verify that subsequently, after receipt of a CALL PROCEEDING message and of an ASSIGNMENT COMMAND message allocating an appropriate TCH, after having completed the traffic channel early assignment procedure by replying with the ASSIGNMENT COMPLETE message, after receipt of an ALERTING message and a CONNECT message, the MS returns a CONNECT ACKNOWLEDGE message.
5) To verify that subsequently the MS has attached the user connection to the radio path. (This is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
6) To verify that subsequently upon the network initiating call clearing by sending a DISCONNECT message, the MS proceed to release the call with RELEASE.
7) To verify that subsequently, on receipt of a RELEASE COMPLETE message followed by a CHANNEL RELEASE message, the MS disconnects the main signalling link.
These test purposes are tested for all rates supported by the MS (full rate/half rate).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.2.3 Method of test
|
(* this affects the 'correct' contents of the SETUP message *)
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1)
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
PIXIT statements:
- Way to indicate mobile originated alerting
- Way to display the called number
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
A teleservice is selected that is supported by the MS; if the MS supports speech version 1, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is made to initiate a call. The call is established with early assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered.
2
MS
If supported, the MS must display the called number in the way defined in PIXIT.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM.
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
MS -> SS
SETUP
12
SS -> MS
CALL PROCEEDING
13
SS -> MS
ASSIGNMENT COMMAND
14
MS -> SS
ASSIGNMENT COMPLETE
15
SS -> MS
ALERTING
16
MS
Depending on the PIXIT, an alerting indication is given.
17
SS -> MS
CONNECT
18
MS -> SS
CONNECT ACKNOWLEDGE
19
MS
The appropriate bearer channel is through connected in both directions.
20
SS -> MS
DISCONNECT
21
MS -> SS
RELEASE
22
SS -> MS
RELEASE COMPLETE
23
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.3 Structured procedures / MS originated call / late assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.3.1 Conformance requirement
|
1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
2) Upon receipt of the ASSIGNMENT COMMAND message, the Mobile Station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause "normal event", to the network on the main DCCH.
3, 4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
- attach the user connection to the radio path;
- return a CONNECT ACKNOWLEDGE message.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.3.1 and 3.4.3.2.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.3.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating an appropriate TCH, the MS sends an ASSIGNMENT COMPLETE message.
3) To verify that subsequently, after the suite of actions specified in test purposes 1 and 2, the MS after receiving a CONNECT message returns a CONNECT ACKNOWLEDGE message.
4) To verify that after the suite of actions specified in test purposes 1 and 2, the MS after receiving a CONNECT message attaches the user connection to the radio path. (This is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
These test purposes are tested for all rates supported by the MS (full rate/half rate).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1)
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
PIXIT statements:
- Way to indicate mobile originated alerting
-. Way to display the called number
Foreseen Final State of the MS
The MS has a MO call in state U10, "active".
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
A teleservice is selected that is supported by the MS; if the MS supports speech version 1, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is made to initiate a call. The call is established with late assignment.
Maximum Duration of Test
30 s.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered.
2
MS
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM.
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
MS -> SS
SETUP
12
SS -> MS
CALL PROCEEDING
13
SS -> MS
ALERTING
14
MS
Depending on the PIXIT, an alerting indication is given.
15
SS -> MS
ASSIGNMENT COMMAND
16
MS -> SS
ASSIGNMENT COMPLETE
17
SS -> MS
CONNECT
18
MS -> SS
CONNECT ACKNOWLEDGE
19
MS
The appropriate bearer channel is through connected in both directions.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.4 Structured procedures / MS terminated call / early assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.4.1 Conformance requirements
|
1) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.
2, 3) Upon receipt of the ASSIGNMENT COMMAND message the MS continues a mobile terminating call establishment with early establishment of the traffic channel
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message, and
b) if the MS supports immediate connect, by continuing the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, by sending an ALERTING message
4) An MS indicates acceptance of a MT call by sending CONNECT.
5)
For speech calls:
The mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
For data calls:
The mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
6) The MS initiates call clearing of an active call by sending a DISCONNECT message.
7) The MS in this phase of call release, upon receipt of a RELEASE message, shall return a RELEASE COMPLETE message.
8) Subsequently the MS, upon receipt of a CHANNEL RELEASE message, shall disconnect the main signalling link.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.2.3.1.
Conformance requirements 2, 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.3.2,
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.3.1.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.2.5.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.6 and 5.2.2.9.
Conformance requirements 6, 7, 8: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.4.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having sent a PAGING RESPONSE message on the allocated SDCCH, after having performed successful authentication and cipher mode setting procedures, after receipt of a SETUP message not containing a signal information element, returns a CALL CONFIRMED message.
2) To verify that subsequently, the SS sending an ASSIGNMENT COMMAND message, the MS successfully continues a mobile terminating call establishment with early assignment of traffic channel:
a) by replying to the ASSIGNMENT COMMAND with an ASSIGNMENT COMPLETE message, and
b) by continuing the call establishment by either:
- sending a CONNECT messages and through connecting the TCH in both directions; or
- sending an ALERTING message.
3) To verify that if after sending a CALL PROCEEDING message, the MS sends an ALERTING message during MTC establishment with early assignment, it generates an alerting indication.
4) To verify that if an ALERTING had been sent, subsequently, when the user accepts the call (possibly internal action as declared in PIXIT statement), the MS returns a CONNECT message.
5) To verify that the MS:
- if the call is a speech call: after sending the CONNECT message has through connected the TCH in both directions (this is checked by verifying that after transmission of the first L2 frame containing the (complete) CONNECT message, the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
- if the call is a data call: after receipt of a subsequent CONNECT ACKNOWLEDGE message through connects the TCH in both directions (this is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT ACKNOWLEDGE message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
6) To verify that subsequently, the MS can initiate call clearing by sending a DISCONNECT message.
7) To verify that the MS in this phase of call release, upon receipt of a RELEASE message, returns a RELEASE COMPLETE message.
8) To verify that subsequently the MS, upon receipt of a CHANNEL RELEASE message, disconnects the main signalling link.
These test purposes are tested for all rates supported by the MS (full rate/half rate).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.4.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
A teleservice is selected that is supported by the MS; if the MS supports speech version 1, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is paged and the resulting call is established. Having reached the active state, the MS is made to clear the call.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
SS -> MS
SETUP
Message does not contain the signal IE.
11
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A12
MS -> SS
CONNECT
sent on the old channel
A13
SS -> MS
ASSIGNMENT COMMAND
A14
MS -> SS
ASSIGNMENT COMPLETE
B12
SS -> MS
ASSIGNMENT COMMAND
B13
MS -> SS
ASSIGNMENT COMPLETE
sent on the new channel
B14
MS -> SS
ALERTING
B15
MS
An alerting indication as defined in a PIXIT statement is given by the MS
B16
MS
The MS is made to accept the call in the way described in a PIXIT statement
B17
MS -> SS
CONNECT
18
MS
If the call is a speech call, the TCH shall be through connected in both directions.
19
SS -> MS
CONNECT ACKNOWLEDGE
20
MS
If the call is a data call, the TCH shall be through connected in both directions.
21
MS
The MS is made to release the call.
22
MS -> SS
DISCONNECT
23
SS -> MS
RELEASE
24
MS -> SS
RELEASE COMPLETE
25
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.5 Structured procedures / MS terminated call / late assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.5.1 Conformance requirement
|
TP1, TP2: The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call. The MS on acceptance of the call sends a CONNECT, otherwise user alerting is initiated.
TP3: The MS indicates acceptance of a call by sending a CONNECT message.
TP4: ASSIGNMENT COMMAND is answered by ASSIGNMENT COMPLETE.
TP5: For speech calls:
The mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
For data calls:
The mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
Requirement reference:
Conformance requirements 1, 2, 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.3.1, 5.2.2.3.2 and 5.2.2.5.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.3.1.
Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.2.9.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.5.2 Test purpose
|
1) To verify that the MS in "Idle, Updated" state with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having established the main signalling link, after having sent a PAGING RESPONSE message, after having performed successful authentication and cipher mode setting procedures, after receipt of a SETUP message containing a signal information element, returns a CALL CONFIRMED message followed by:
- an ALERTING message;
- or a CONNECT message.
2) To verify that in the situation of test purpose 1, if the MS sends an ALERTING message, the MS generates an alerting indication in the way described in a PIXIT statement.
3) To verify that subsequently the MS, if it had not yet sent a CONNECT message, upon acceptance of the call, sends a CONNECT message.
4) To verify that subsequently after receipt of an ASSIGNMENT COMMAND, the MS sends an ASSIGNMENT COMPLETE message.
5) To verify that subsequently the MS:
- if the call is a speech call: after sending the ASSIGNMENT COMPLETE message has through connected the TCH in both directions (this is checked by verifying that after transmission of the first L2 frame containing the (complete) ASSIGNMENT COMPLETE message, the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
- if the call is a data call: after receipt of a subsequent CONNECT ACKNOWLEDGE message through connects the TCH in both directions (this is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT ACKNOWLEDGE message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
These test purposes are tested for all rates supported by the MS (full rate/half rate).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.5.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1).
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of the MS
CC state U10-call active.
Test procedure
The following test is performed for all rates (full rate/half rate) supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech version 1, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is paged and a MT call is established with late assignment (after CONNECT).
Maximum Duration of Test
40 s.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel.
2
MS -> SS
CHANNEL REQUEST
Establishment cause indicates "answer to paging".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
SS -> MS
SETUP
Message contains the signal IE.
11
MS -> SS
CALL CONFIRMED
A12
MS -> SS
CONNECT
B12
MS -> SS
ALERTING
B13
MS
An alerting indication as defined in an PIXIT statement is given by the MS.
B14
MS
The MS is made to accept the call in the way described in a PIXIT statement.
B15
MS -> SS
CONNECT
16
SS -> MS
ASSIGNMENT COMMAND
17
MS -> SS
ASSIGNMENT COMPLETE
18
MS
If the call is a speech call, the TCH shall be through connected in both directions.
19
SS -> MS
CONNECT ACKNOWLEDGE
20
MS
If the call is a data call, the MS shall through connect the TCH in both directions.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6 Structured procedures / emergency call
|
Emergency call establishment can be initiated by an MS whether location updating has been successful or not and whether a SIM is inserted into the MS or not; but only if the MS is equipped for speech.
If the procedures tested in this subclause are not correctly implemented in the MS, establishment, maintenance and clearing of connections might fail in the essential case of emergency calls.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1 Structured procedures / emergency call / idle updated
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.1 Structured procedures / emergency call / idle updated / preferred channel rate
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.1.1 Conformance requirement
|
1) For R97/98 MS: The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
For R99 MS: When a SIM/USIM containing stored emergency numbers is present, those numbers are identified as emergency numbers. As an optional requirement, the ME shall also identify 112 and 911 as emergency numbers irrespective of whether these are stored in the SIM/USIM. Any other emergency numbers stored in the ME shall be ignored.
When no emergency numbers are stored within the SIM the following numbers shall be stored in the ME for use as emergency numbers: 112, and 911.
When no emergency numbers are stored within the USIM the following numbers shall be stored in the ME for use as emergency numbers: 112, and 911.
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct CKSN and TMSI , with CM Service Type "emergency call establishment".
3) Authentication and cipher mode setting shall be performed successfully.
4) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
5), 6) The emergency call shall be correctly established. The assignment procedure shall be correctly performed.
7) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH shall be through connected in both directions if an appropriate TCH is available.
8) The call shall be cleared correctly.
Requirement Reference:
For conformance requirement 1 and 2:
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1,
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5,
3GPP TS 02.30 clause 4,
3GPP TS 22.101 clauses 8.
For conformance requirement 3:
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.7,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.3.2.
For conformance requirement 4:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.1.
For conformance requirement 5 and 6:
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.1,
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3.
For conformance requirement 7:
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.6 and 5.1.3.
For conformance requirement 8:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.1.2 Test purpose
|
1) To verify that an R97/R98 MS supporting speech in the MM state "idle, updated", when made to call the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL REQUEST message with establishment cause "emergency call".
To verify that an R99 MS supporting speech (or a R97/98 MS using the R99 Emergency Numbers) in the MM state "idle, updated", when made to call the number 112 or 911, sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message specifying the correct CKSN and TMSI, with CM Service Type "emergency call establishment".
3) To verify that authentication and cipher mode setting are performed successfully.
4) To verify that after cipher mode setting acceptance by the SS, the MS sends an EMERGENCY SETUP message.
5) To verify that subsequently, the SS having sent a CALL PROCEEDING message and then an ALERT message and having initiated the assignment procedure of an appropriate speech traffic channel, which, if the MS supports both TCH/FS and TCH/HS, is at the preferred rate, the MS performs correctly that assignment procedure.
6) To verify subsequent correct performance of a connect procedure.
7) To verify that subsequently the MS has through connected the TCH in both directions.
8) To verify that the call is cleared correctly.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Use of R99 Emergency numbers (TSPC_R99_Emerg)
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The MS is made to initiate an emergency call. The call is established with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
MS -> SS
EMERGENCY SETUP
If half rate speech version 1 is supported, the message must contain one bearer capability IE indicating in the radio channel requirement field "dual rate/half rate preferred" or "dual rate/full rate preferred". If half rate speech version 1 is not supported, the message must either contain no bearer capability IE or contain one bearer capability IE indicating in the radio channel requirement field "full rate channel".
If the emergency category IE is included, then SS verifies that the Emergency Service Category IE bit 6 and bit 7 is not set to 1
12
SS -> MS
CALL PROCEEDING
13
SS -> MS
ALERTING
14
SS -> MS
ASSIGNMENT COMMAND
The rate of the channel is that one indicated by the EMERGENCY SETUP message, if that message did not offer a choice, and the rate is the preferred one else.
15
MS -> SS
ASSIGNMENT COMPLETE
16
SS -> MS
CONNECT
17
MS -> SS
CONNECT ACKNOWLEDGE
18
MS
The TCH is through connected in both directions.
19
SS -> MS
DISCONNECT
20
MS -> SS
RELEASE
21
SS -> MS
RELEASE COMPLETE
23
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Note: According to the conformance requirements there is no need to execute the test case by dialling the number 08 for an R99 MS (or a R97/98 MS using the R99 Emergency numbers)
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.2 Structured procedures / emergency call / idle updated, non-preferred channel rate
|
This test is identical to the test in subclause 26.9.6.1.1 except that in step 14 the assigned TCH has the non-preferred rate.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.3 Structured procedures / emergency call / idle updated / EAB active
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.3.1 Conformance requirement
|
The preliminary access barring check shall indicate network access is barred if all of the following conditions are satisfied:
• the establishment cause for the request received from the MM sublayer is not "emergency call".
• the SYSTEM INFORMATION TYPE 21 message is broadcast in the cell and includes EAB information;
• the mobile station is a member of a subcategory of mobile stations targeted by the EAB information;
• the EAB Authorization Mask sent in the EAB information indicates the mobile station’s access class is not authorized;
• the mobile station is not a member of any of the authorized special access classes (i.e. an Access Class in the range 11-15) permitted by the network;
An MS configured for NAS signalling low priority indicates this by including the Device properties IE in the appropriate NAS message and setting the low priority indicator to "MS is configured to NAS signalling low priority" except for the following cases in which the MS shall set the low priority indicator to "MS is not configured for NAS signalling low priority":
- the MS is performing an attach for emergency bearer services;
- the MS has a PDN connection for emergency bearer services established and is performing mobility management procedures, or is establishing a PDN connection for emergency bearer services;
- the MS is accessing the network with access class 11 – 15; or
- the MS is responding to paging.
Reference:
3GPP TS 44.018 subclause 3.3.1.4, 3GPP TS 24.008 subclause 1.8
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.3.2 Test purpose
|
To verify that the MS, configured for Extended Access class Barring can initiate an emergency call when EAB is being broadcast
To verify that the Low Access Priority indicator is set in the Service Request message
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.1.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
The SYSTEM INFORMATION TYPE 3 message indicates that the SYSTEM INFORMATION TYPE 21 is sent on the BCCH by setting the SYSTEM INFORMATION 21 Indicator in the SI3 Rest Octet IE.
The SYSTEM INFORMATION TYPE 21 is sent on the BCCH. The SI 21 Rest Octets information element is configured with: EAB Authorization Mask set to”xxxxxxxxx1” and EAB Subcategory set to “00”.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.¨
The MS is configured for “Extended Access Barring” and “low access priority”
The MS belong to access class 0
Specific PICS statements:
-
PIXIT statements:
-
Foreseen Final State of the MS
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Test procedure
The SS waits until all system information messages, including SYSTEM INFORMATION TYPE 21, is sent. The SI 21 Rest Octets information element is configured with: EAB Authorization Mask set to”xxxxxxxxx1” and EAB Subcategory set to “00” in SYSTEM INFORMATION TYPE 21.
The MS is made to initiate an emergency call. The call is established with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
The SS waits until it has sent all system information messages
2
MS
The appropriate emergency call number is entered.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is emergency call establishment.
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The Device properties IE indicates “NAS signalling low priority”
6
SS -> MS
AUTHENTICATION REQUEST
7
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
8
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
9
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
10
SS
SS starts ciphering.
11
MS -> SS
EMERGENCY SETUP
If the emergency category IE is included, then SS verifies that the Emergency Service Category IE bit 6 and bit 7 is not set to 1
12
SS -> MS
CALL PROCEEDING
13
SS -> MS
ALERTING
14
SS -> MS
ASSIGNMENT COMMAND
15
MS -> SS
ASSIGNMENT COMPLETE
16
SS -> MS
CONNECT
17
MS -> SS
CONNECT ACKNOWLEDGE
18
MS
The TCH is through connected in both directions.
19
SS -> MS
DISCONNECT
20
MS -> SS
RELEASE
21
SS -> MS
RELEASE COMPLETE
23
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
SYSTEM INFORMATION TYPE 3 broadcast in the cell:
Same as default content except
Information Element
Value/remark
SI 3 Rest Octets
SYSTEM INFORMATION 21 Indicator
H (SYSTEM INFORMATION TYPE 21 message is available)
SI21_POSITION
0 (SYSTEM INFORMATION TYPE 21 message is sent on BCCH Norm)
SYSTEM INFORMATION TYPE 21 broadcast by Cell A initially and in steps 11 and 20:
Same as default content except
Information Element
Value/remark
SI 21 Rest Octets
EAB Authorization Mask
‘xxxxxxxxx1’ (MSs configured for EAB and a member of Access Class 0 are barred)
EAB Subcategory
‘00’ (applicable to all mobile stations configured for EAB)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2 Structured procedures / emergency call / idle, no IMSI
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.1 Structured procedures / emergency call / idle, no IMSI / accept case
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.1.1 Conformance requirement
|
1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct IMEI and a non-available CKSN, with CM Service Type "emergency call establishment".
3) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
4),5) The emergency call shall be correctly established. The assignment procedure shall be correctly performed.
6) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH shall be through connected in both directions if an appropriate TCH is available.
7) The call shall be cleared correctly.
Requirement Reference:
For conformance requirement 1 and 2:
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1,
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5,
3GPP TS 02.30 clause 4.
For conformance requirement 3:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.1.
For conformance requirements 4 and 5:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.1,
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3.
For conformance requirement 6:
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.6 and 5.1.3.
For conformance requirement 7:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.1.2 Test purpose
|
1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico), sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message in which the cipher key sequence number IE indicates "no key is available", the CM service type IE indicates "emergency number establishment", and the mobile identity IE specifies the IMEI of the MS.
3) To verify that after receipt of a CM SERVICE ACCEPT message from the SS, the MS sends an EMERGENCY SETUP message.
4) To verify that subsequently, the SS having sent a CALL PROCEEDING message and then an ALERT message and having initiated the assignment procedure of an appropriate speech traffic channel, which, if the MS supports both TCH/FS and TCH/HS, is at the preferred rate, the MS performs correctly that assignment procedure.
5) To verify subsequent correct performance of a connect procedure.
6) To verify that subsequently the MS has through connected the TCH in both directions.
7) To verify that the call is cleared correctly.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Specific PICS statements:
- .
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Test procedure
The MS is made to initiate an emergency call. The call is established without authentication, without ciphering, with late assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate emergency call number is entered.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "emergency call".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The mobile identity IE specifies the IMEI of the MS. The cipher key sequence number IE indicates "no key is available".
4
SS -> MS
CM SERVICE ACCEPT
11
MS -> SS
EMERGENCY SETUP
If the emergency category IE is included, then SS verifies that the Emergency Service Category IE bit 6 and bit 7 is not set to 1
12
SS -> MS
CALL PROCEEDING
13
SS -> MS
ALERTING
14
SS -> MS
ASSIGNMENT COMMAND
The rate of the channel is one indicated by the EMERGENCY SETUP message.
15
MS -> SS
ASSIGNMENT COMPLETE
16
SS -> MS
CONNECT
17
MS -> SS
CONNECT ACKNOWLEDGE
18
MS
The TCH is through connected in both directions.
19
SS -> MS
DISCONNECT
20
MS -> SS
RELEASE
21
SS -> MS
RELEASE COMPLETE
23
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.2 Structured procedures / emergency call / idle, no IMSI / reject case
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.2.1 Conformance requirement
|
1) The MS in the "idle, no IMSI" state (no SIM inserted), after the number 112 (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) has been entered, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct IMEI and a non-available CKSN, with CM Service Type "emergency call establishment".
3) In the situation at the end of test purpose 2, when the MS receives a CM SERVICE REJECT message, it shall abandon the emergency call.
Requirement Reference:
For conformance requirement 1 and 2:
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1,
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5,
3GPP TS 02.30 clause 4.
For conformance requirement 3:
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.7,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.5.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.2.2 Test purpose
|
1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112, (for GSM 900 and 1800 MS), or 911 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in USA and Canada), or 08 (for GSM 710, GSM 750, T-GSM 810, GSM 850 and PCS 1 900 MS in Mexico) sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message in which the cipher key sequence number IE indicates "no key is available", the CM service type IE indicates "emergency call establishment", and the mobile identity IE specifies the IMEI of the MS.
3) To verify that after receipt of a CM SERVICE REJECT message from the SS, the MS abandons the emergency call establishment.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.6.2.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Specific PICS statements:
- .
PIXIT statements:
- .
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Test procedure
The MS is made to initiate an emergency call. The call is established without authentication, without ciphering, with early assignment. The SS responds to the CM SERVICE REQUEST from the MS with a CM SERVICE REJECT message specifying in the reject cause IE the reject cause value "IMEI not accepted". The SS then verifies for during 5 s that the MS does not send a layer 3 message. Then the call is cleared by the SS. The SS verifies during 20 s after disconnection of the main signalling link that the MS does not initiate an RR connection establishment.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The appropriate call number is entered.
3
MS -> SS
CHANNEL REQUEST
Establishment cause is "emergency call".
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The mobile identity IE specifies the IMEI of the MS. The cipher key sequence number IE indicates "no key is available".
4
SS -> MS
CM SERVICE REJECT
the reject cause IE specifies reject cause value #5, "IMEI not accepted".
5
SS
During 5 s, the SS verifies that the MS does not send L3 messages.
6
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
7
SS
During 20 s, the SS verifies that the MS does not initiate an RR connection establishment.
Specific Message Contents:
-
26.9.6a Structured Calls /eCall
eCall establishment can be initiated by a MS whether location updating has been successful or not, but only if the MS supports eCall capability and has a valid USIM provisioned for the eCall service.
If the procedures tested in this clause are not correctly implemented in the MS, establishment, maintenance or clearing of connections might fail in the essential case of eCall.
Note: eCall functionality has to be tested with Test USIM as defined in Annex 4a.
26.9.6a.1 eCall with USIM
26.9.6a.1.1 Void
26.9.6a.1.2 Test eCall using eCall capable MS with ’eCall only’ subscription on USIM
26.9.6a.1.2.1 Conformance Requirement
The eCall inactivity procedure is applicable only to an eCall only mobile station (as determined by information configured in USIM).
[..]
While in eCALL INACTIVE state, the mobile station maintains awareness of a potential serving cell in a potential serving network but initiates no MM signalling with the network and ignores any paging requests.
The mobile station shall leave eCALL INACTIVE state only when one of the following events occur:
[..]
- if there is a CM request for a call to an HPLMN designated non-emergency MSISDN for the purpose of accessing test and terminal reconfiguration services: the mobile station attempts normal location updating. Once this is complete, further MM and CM procedures are used to establish the non-emergency call.
Reference(s)
3GPP TS 24.008 subclauses 4.4.7
26.9.6a.1.2.2 Test purpose
1. Verify that the eCall only capable MS is capable of making a test eCall.
26.9.6a.1.2.3 Method of test
Initial conditions
The eCall only capable MS is equipped with eCall enabled USIM.
System Simulator
1 cell, default parameters, Ciphering Off
T3212 set to 12 Minutes. ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°2 Fixed Dialling Numbers (FDN) and Service n°89 eCall Data available
EFFDN
Display two FDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT Statement(s)
-
Test procedure
a. MS is powered on. SS monitors to verify that MS does not attempt to register for a period of 120 seconds.
b. MS is made to initiate a Test eCall in accordance with manufacturer’s instructions . SS checks that MS performs registration before starting Test eCall.
c. Having reached the active state, the call is cleared by the SS. SS monitors to verify that MS remains registered and send a periodic LAU message as T3212 timer is set to 12 minutes.
Maximum Duration of Test
20 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
SS
The SS verifies for 120 sec that the MS does not send RACH or any other message.
3
MS
MS is made to initiate a Test eCall (The first number stored in the EFFDN field)
4
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating.
5
SS->MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal location updating/IMSI Attach.
7
SS->MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
9
SS -> MS
LOCATION UPDATING ACCEPT
10
MS -> SS
TMSI REALLOCATION
COMPLETE
11
SS -> MS
CHANNEL RELEASE
12
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to “originating call”
13
SS->MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
CM SERVICE REQUEST
15
SS -> MS
CM SERVICE ACCEPT
16
MS -> SS
SETUP
Verify called number is the test eCall number.
(The first number stored in the EFFDN field)
17
SS -> MS
CALL PROCEEDING
18
SS -> MS
ALERTING
19
MS
Depending on the PIXIT, an alerting indication is given.
20
SS -> MS
ASSIGNMENT COMMAND
21
MS -> SS
ASSIGNMENT COMPLETE
22
SS -> MS
CONNECT
23
MS -> SS
CONNECT ACKNOWLEDGE
24
MS
Traffic channel is kept active for at least 5 seconds.
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
29
SS
SS verifies that MS sends periodic Location Update Request after 12 minutes (5% margin is allowed).
Specific Message Contents
None
26.9.6a.1.3 Manually initiated eCall using eCall capable MS with ’eCall only’ subscription on USIM
26.9.6a.1.3.1 Conformance Requirement
1. When in state MM IDLE and service state eCALL INACTIVE, the mobile station shall:
- not perform periodic updating;
- not perform IMSI detach;
- reject any requests from CM entities for MM connections except for emergency calls and calls to a non-emergency MSISDN for test and terminal reconfiguration services;
- not perform normal location updating; and
- not respond to paging.
2. An eCall only mobile station (as determined by information configured in USIM), shall start timer T3242 if the return to MM IDLE state is subsequent to an emergency services call and shall start timer T3243 if the return to MM IDLE state is subsequent to a call to a non-emergency MSISDN for test and terminal reconfiguration services, as described in subclause 4.4.7
Reference(s)
3GPP TS 24.008 subclauses 4.2.2.9, 4.2.3
26.9.6a.1.3.2 Test purpose
Verify that the eCall capable mobile equipped with USIM subscription restricted to eCall only
1. Able to make eCall
2. Registers to the NW as an eCall is initiated.
26.9.6a.1.3.3 Method of test
Initial conditions
The eCall capable MS is equipped with USIM subscription restricted to eCall only.
System Simulator
1 cell, default parameters, Ciphering Off
ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°2 Fixed Dialling Numbers (FDNDN) and Service n°89 eCall Data available
EFFDN
Display two FDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT statement(s)
-
Test procedure
a) MS is powered on. SS monitors to verify that MS does not attempt to register for a period of 120 seconds.
b) MS is made to initiate an eCall in accordance with manufacturer’s instructions. SS checks that MS performs registration before starting an eCall.
c) Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
5minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
SS
The SS verifies for 120 sec that the MS does not send RACH or any other message.
3
MS
MS is made to initiate a manual eCall
4
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating.
5
SS->MS
IMMEDIATE ASSIGNMENT
6
MS ->SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal location updating/IMSI Attach.
7
SS->MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
LOCATION UPDATING ACCEPT
10
MS -> SS
TMSI REALLOCATION COMPLETE
11
SS -> MS
CHANNEL RELEASE
12
MS -> SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with “Establishment cause is emergency call establishment”
13
SS -> MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
15
SS -> MS
CM SERVICE ACCEPT
16
MS -> SS
EMERGENCY SETUP
SS verifies that optional IE “Service category” should be present and bit 6 should be set to 1 and bit 7 should be set to 0.
17
SS -> MS
CALL PROCEEDING
18
SS -> MS
ALERTING
19
SS -> MS
ASSIGNMENT COMMAND
20
MS -> SS
ASSIGNMENT COMPLETE
21
SS -> MS
CONNECT
22
MS -> SS
CONNECT ACKNOWLEDGE
23
MS
Traffic channel is kept active for at least 5 seconds.
24
SS -> MS
DISCONNECT
25
MS -> SS
RELEASE
26
SS -> MS
RELEASE COMPLETE
27
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
None
26.9.6a.1.4 Manually initiated eCall using eCall capable MS with eCall capable USIM
26.9.6a.1.4.1 Conformance Requirement
1. eCall and Normal call support
Requirement: Service n° 89 and Service n° 4 are "available".
Request: The ME performs the reading procedure with EFSDN.
If eCall and normal calls are supported, then the last two entries of EFSDN shall contain the eCall test number and the eCall reconfiguration number respectively. A terminal in eCall and normal mode performs the SDN related procedures.
2. TBD
Table 10.5.135d/3GPP TS 24.008: Service Category information element
Emergency Service Category Value (octet 3)
The meaning of the Emergency Category Value is derived from the following settings (see 3GPP TS 22.101 [8] clause 10):
Bit 1 Police
Bit 2 Ambulance
Bit 3 Fire Brigade
Bit 4 Marine Guard
Bit 5 Mountain Rescue
Bit 6 manually initiated eCall
Bit 7 automatically initiated eCall
Bit 8 is spare and set to "0"
Mobile station may set one or more bits to "1"
If more than one bit is set to "1", routing to a combined Emergency centre (e.g. ambulance and fire brigade in Japan) is required. If the MSC can not match the received service category to any of the emergency centres, it shall route the call to an operator defined default emergency centre.
If no bit is set to "1", the MSC shall route the Emergency call to an operator defined default emergency centre.
A mobile station initiating an eCall shall set either bit 6 or bit 7 to “1”. The network may use the information indicated in bit 6 and bit 7 to route the manually or automatically initiated eCall to an operator defined emergency call centre.
Reference(s)
TS31.102 clause 5.3.40.2, TS 24.008 subclauses10.5.4.33
26.9.6a.1.4.2 Test purpose
Verify that the eCall capable mobile equipped with eCall and non eCall subscription on USIM
1. Performs LAU when Switched on
2. Able to make eCall.
26.9.6a.1.4.3 Method of test
Initial conditions
The eCall capable MS is equipped with eCall and non eCall subscription on USIM.
System Simulator
1 cell, default parameters, ciphering off
ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°4 Service Dialling Numbers (SDN) and Service n°89 eCall Data available
EFSDN
Display two SDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT statement(s)
-
Test procedure
a) MS is powered on.
b) SS checks that MS successfully performs LAU.
c) MS is made to initiate an eCall in accordance with manufacturer’s instructions.
d) Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
5 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating within 60 sec.
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS ->SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal Location Updating/IMSI attach.
5
SS->MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
7
SS -> MS
LOCATION UPDATING ACCEPT
8
MS -> SS
TMSI REALLOCATION COMPLETE
9
SS -> MS
CHANNEL RELEASE
10
MS
MS is made to initiate a manual eCall
11
MS -> SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with “Establishment cause is emergency call establishment”
12
SS -> MS
IMMEDIATE ASSIGNMENT
13
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
14
SS -> MS
CM SERVICE ACCEPT
15
MS -> SS
EMERGENCY SETUP
SS verifies that optional IE “Service category” should be present and bit 6 should be set to 1 and bit 7 should be set to 0.
16
SS -> MS
CALL PROCEEDING
17
SS -> MS
ALERTING
18
SS -> MS
ASSIGNMENT COMMAND
19
MS -> SS
ASSIGNMENT COMPLETE
20
SS -> MS
CONNECT
21
MS -> SS
CONNECT ACKNOWLEDGE
22
MS
Traffic channel is kept active for at least 5 seconds.
23
SS -> MS
DISCONNECT
24
MS -> SS
RELEASE
25
SS -> MS
RELEASE COMPLETE
26
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
None
26.9.6a.1.5 eCall Inactivity State after T3242 expires
26.9.6a.1.5.1 Conformance Requirement
1. When in state MM IDLE and service state eCALL INACTIVE, the mobile station shall:
- not perform periodic updating;
- not perform IMSI detach;
- reject any requests from CM entities for MM connections except for emergency calls and calls to a non-emergency MSISDN for test and terminal reconfiguration services;
- not perform normal location updating; and
- not respond to paging.
2. An eCall only mobile station (as determined by information configured in USIM), shall start timer T3242 if the return to MM IDLE state is subsequent to an emergency services call and shall start timer T3243 if the return to MM IDLE state is subsequent to a call to a non-emergency MSISDN for test and terminal reconfiguration services, as described in subclause 4.4.7.
3. The mobile station shall leave eCALL INACTIVE state only when one of the following events occur:
- if the SIM or USIM is removed, the mobile station enters the NO IMSI state;
- if coverage is lost, the mobile station enters PLMN SEARCH state;
- if the mobile station is deactivated (e.g. powered off) by the user: the mobile station enters the NULL state;
- if there is a CM request for an emergency services call: the MS uses the MM and CM procedures to establish the emergency call; or
- if there is a CM request for a call to an HPLMN designated non-emergency MSISDN for the purpose of accessing test and terminal reconfiguration services: the mobile station attempts normal location updating. Once this is complete, further MM and CM procedures are used to establish the non-emergency call.
Reference(s)
3GPP TS 24.008 subclauses 4.2.2.9, 4.2.3, 4.4.7
26.9.6a.1.5.2 Test purpose
Verify that the eCall capable mobile equipped with USIM subscription restricted to eCall only
1. Able to make eCall
2. Registers to the NW as an eCall is initiated.
3. Remains registered on the network for a duration of T3242 following completion of an eCall.
4. Detaches from network upon expiry of T3242.
5. Comes out of the eCall Inactive state when eCall is initiated (MS should register back to NW and then initiate eCall)
26.9.6a.1.5.3 Method of test
Initial conditions
The eCall capable MS is equipped with USIM subscription restricted to eCall only.
System Simulator
1 cell, default parameters, ciphering off
T3212 set to 252 Minutes. ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°2 Fixed Dialling Numbers (FDN) and Service n°89 eCall Data available
EFFDN
Display two FDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT statement(s)
-
Test procedure
a) MS is powered on. SS monitors to verify that MS does not attempt to register for a period of 120 seconds.
b) MS is made to initiate an eCall in accordance with manufacturer’s instructions. SS checks that MS performs registration before starting an eCall.
c) Having reached the active state, the call is cleared by the SS. SS monitors to verify that MS remains registered for the duration of T3242 and send LAU messages every 252 mins (as T3212 timer is set to 252 minutes).
d) Upon expiry of timer T3242 the MS shall perform IMSI detach.
e) MS is made to initiate an eCall. SS checks that MS performs registration before starting an eCall.
f) Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
12 hours 20 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
SS
The SS verifies for 120 sec that the MS does not send RACH or any other message.
3
MS
MS is made to initiate a manual eCall
4
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating.
5
SS->MS
IMMEDIATE ASSIGNMENT
6
MS ->SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal location updating/IMSI Attach.
7
SS->MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
9
SS -> MS
LOCATION UPDATING ACCEPT
10
MS -> SS
TMSI REALLOCATION COMPLETE
11
SS -> MS
CHANNEL RELEASE
12
MS -> SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with “Establishment cause is emergency call establishment”
13
SS -> MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
15
SS -> MS
CM SERVICE REQUEST
16
MS -> SS
EMERGENCY SETUP
SS verifies that optional IE “Service category” should be present and bit 6 should be set to 1 and bit 7 should be set to 0.
17
SS -> MS
CALL PROCEEDING
18
SS -> MS
ALERTING
19
SS -> MS
ASSIGNMENT COMMAND
20
MS -> SS
ASSIGNMENT COMPLETE
21
SS -> MS
CONNECT
22
MS -> SS
CONNECT ACKNOWLEDGE
23
MS
Traffic channel is kept active for at least 5 seconds.
24
SS -> MS
DISCONNECT
25
MS -> SS
RELEASE
26
SS -> MS
RELEASE COMPLETE
27
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
28
SS
For next 12 hours 10 mins SS verifies that
1. MS sends Location Update Request periodically every 252 minutes( 5% margin is allowed).
2. MS performs IMSI detach after timer T3242 expires (12 hours) 1% margin is allowed.
29
MS
MS is made to initiate a manual eCall
30
SS
MS should perform LAU.
31
MS -> SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with “Establishment cause is emergency call establishment”
32
SS -> MS
IMMEDIATE ASSIGNMENT
33
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
34
SS -> MS
CM SERVICE ACCEPT
35
MS -> SS
EMERGENCY SETUP
SS verifies that optional IE “Service category” should be present and bit 6 should be set to 1 and bit 7 should be set to 0.
36
SS -> MS
CALL PROCEEDING
37
SS -> MS
ALERTING
38
SS -> MS
ASSIGNMENT COMMAND
39
MS -> SS
ASSIGNMENT COMPLETE
40
SS -> MS
CONNECT
41
MS -> SS
CONNECT ACKNOWLEDGE
42
MS
The TCH is connected in both directions.
43
SS
Traffic channel is kept active for at least 5 seconds.
44
SS -> MS
DISCONNECT
45
MS -> SS
RELEASE
46
SS -> MS
RELEASE COMPLETE
47
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
None
26.9.6a.1.6 Automatically initiated eCall
26.9.6a.1.6.1 Conformance Requirement
[..]
Table 10.5.135d/3GPP TS 24.008: Service Category information element
Emergency Service Category Value (octet 3)
The meaning of the Emergency Category Value is derived from the following settings (see 3GPP TS 22.101 [8] clause 10):
Bit 1 Police
Bit 2 Ambulance
Bit 3 Fire Brigade
Bit 4 Marine Guard
Bit 5 Mountain Rescue
Bit 6 manually initiated eCall
Bit 7 automatically initiated eCall
Bit 8 is spare and set to "0"
Mobile station may set one or more bits to "1"
If more than one bit is set to "1", routing to a combined Emergency centre (e.g. ambulance and fire brigade in Japan) is required. If the MSC can not match the received service category to any of the emergency centres, it shall route the call to an operator defined default emergency centre.
If no bit is set to "1", the MSC shall route the Emergency call to an operator defined default emergency centre.
A mobile station initiating an eCall shall set either bit 6 or bit 7 to “1”. The network may use the information indicated in bit 6 and bit 7 to route the manually or automatically initiated eCall to an operator defined emergency call centre.
Reference(s)
3GPP TS 24.008 subclauses10.5.4.33
26.9.6a.1.6.2 Test purpose
Verify that the eCall capable mobile equipped with eCall and non eCall subscription on USIM
1. Performs LAU when Switched on
2. Able to make an Automatic eCall.
3. MS provides appropriate Service Category information to the network when Automatic eCall is initiated.( Bit 7 should be set to 1 and Bit 6 should be set to 0).
26.9.6a.1.6.3 Method of test
Initial conditions
The eCall capable MS is equipped with eCall and non eCall subscription on USIM.
System Simulator
1 cell, default parameters, ciphering off
ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below
USIM field
Contents
EFUST
Service n°4 Service Dialling Numbers (SDN) and Service n°89 eCall Data available
EFSDN
Display two SDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT statement(s)
-
Test procedure
a) MS is powered on.
b) SS checks that MS successfully performs LAU.
c) MS is made to initiate an automatic eCall in accordance with manufacturer’s instructions. SS verifies that MS provides appropriate Service Category information to the network. ( Bit 7 should be set to 1 and Bit 6 should be set to 0).
d) Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
5 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating within 60 sec.
3
SS->MS
IMMEDIATE ASSIGNMENT
4
MS ->SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal Location Updating/IMSI attach.
5
SS->MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
7
SS -> MS
LOCATION UPDATING ACCEPT
8
MS -> SS
TMSI REALLOCATION COMPLETE
9
SS -> MS
CHANNEL RELEASE
10
MS
MS is made to initiate an Automatic eCall
11
MS -> SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with “Establishment cause is emergency call establishment”
12
SS -> MS
IMMEDIATE ASSIGNMENT
13
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment".
14
SS -> MS
CM SERVICE ACCEPT
15
MS -> SS
EMERGENCY SETUP
SS verifies that optional IE “Service category” should be present and bit 6 should be set to 0 and bit 7 should be set to 1.
16
SS -> MS
CALL PROCEEDING
17
SS -> MS
ALERTING
18
SS -> MS
ASSIGNMENT COMMAND
19
MS -> SS
ASSIGNMENT COMPLETE
20
SS -> MS
CONNECT
21
MS -> SS
CONNECT ACKNOWLEDGE
22
MS
Traffic channel is kept active for at least 5 seconds.
23
SS -> MS
DISCONNECT
24
MS -> SS
RELEASE
25
SS -> MS
RELEASE COMPLETE
26
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
None
26.9.6a.1.7 Reconfiguration eCall using eCall capable MS with ‘eCall only’ subscription on USIM
26.9.6a.1.7.1 Conformance Requirement
The eCall inactivity procedure is applicable only to an eCall only mobile station (as determined by information configured in USIM).
[..]
While in eCALL INACTIVE state, the mobile station maintains awareness of a potential serving cell in a potential serving network but initiates no MM signalling with the network and ignores any paging requests.
The mobile station shall leave eCALL INACTIVE state only when one of the following events occur:
[..]
- if there is a CM request for a call to an HPLMN designated non-emergency MSISDN for the purpose of accessing test and terminal reconfiguration services: the mobile station attempts normal location updating. Once this is complete, further MM and CM procedures are used to establish the non-emergency call.
Reference(s)
3GPP TS 24.008 subclauses 4.4.7
26.9.6a.1.7.2 Test purpose
1. Verify that the eCall capable MS is capable of making a reconfiguration eCall.
26.9.6a.1.7.3 Method of test
Initial conditions
The eCall capable MS is equipped with eCall only enabled USIM.
System Simulator
1 cell, default parameters, Ciphering Off
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°2 Fixed Dialling Numbers (FDN) and Service n°89 eCall Data available
EFFDN
Display two FDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT Statement(s)
-
Test procedure
a. MS is powered on. SS monitors to verify that MS does not attempt to register for a period of 120 seconds.
b. MS is made to initiate a reconfiguration eCall in accordance with manufacturer’s instructions . SS checks that MS performs registration before starting reconfiguration eCall.
c. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
5 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
SS
The SS verifies for 120 sec that the MS does not send RACH or any other message.
3
MS
MS is made to initiate a reconfiguration eCall (The second number stored in the EFFDN field)
4
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating.
5
SS->MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal location updating/IMSI Attach.
7
SS->MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
9
SS -> MS
LOCATION UPDATING ACCEPT
10
MS -> SS
TMSI REALLOCATION
COMPLETE
11
SS -> MS
CHANNEL RELEASE
12
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to “originating call”
13
SS->MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
CM SERVICE REQUEST
15
SS->MS
CM SERVICE ACCEPT
16
MS -> SS
SETUP
Verify called number is the reconfiguration eCall number.
(The second number stored in the EFFDN field)
17
SS -> MS
CALL PROCEEDING
18
SS -> MS
ALERTING
19
MS
Depending on the PIXIT, an alerting indication is given.
20
SS -> MS
ASSIGNMENT COMMAND
21
MS -> SS
ASSIGNMENT COMPLETE
22
SS -> MS
CONNECT
23
MS -> SS
CONNECT ACKNOWLEDGE
24
MS
Traffic channel is kept active for at least 5 seconds.
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
None
26.9.6a.1.8 eCall Inactivity State after T3243 expires
26.9.6a.1.8.1 Conformance Requirement
1. When in state MM IDLE and service state eCALL INACTIVE, the mobile station shall:
- not perform periodic updating;
- not perform IMSI detach;
- reject any requests from CM entities for MM connections except for emergency calls and calls to a non-emergency MSISDN for test and terminal reconfiguration services;
- not perform normal location updating; and
- not respond to paging.
2. An eCall only mobile station (as determined by information configured in USIM), shall start timer T3242 if the return to MM IDLE state is subsequent to an emergency services call and shall start timer T3243 if the return to MM IDLE state is subsequent to a call to a non-emergency MSISDN for test and terminal reconfiguration services, as described in subclause 4.4.7.
3. The mobile station shall leave eCALL INACTIVE state only when one of the following events occur:
- if the SIM or USIM is removed, the mobile station enters the NO IMSI state;
- if coverage is lost, the mobile station enters PLMN SEARCH state;
- if the mobile station is deactivated (e.g. powered off) by the user: the mobile station enters the NULL state;
- if there is a CM request for an emergency services call: the MS uses the MM and CM procedures to establish the emergency call; or
- if there is a CM request for a call to an HPLMN designated non-emergency MSISDN for the purpose of accessing test and terminal reconfiguration services: the mobile station attempts normal location updating. Once this is complete, further MM and CM procedures are used to establish the non-emergency call.
Reference(s)
3GPP TS 24.008 subclauses 4.2.2.9, 4.2.3, 4.4.7
26.9.6a.1.8.2 Test purpose
Verify that the eCall capable mobile equipped with USIM subscription restricted to eCall only
1. Able to make a test eCall.
2. Registers to the NW as a test eCall is initiated.
3. Remains registered on the network for a duration of T3243 following completion of a test eCall.
4. Detaches from network upon expiry of T3243.
5. Comes out of the eCall Inactive state when a test eCall is initiated (MS should register back to NW and then initiate test eCall).
26.9.6a.1.8.3 Method of test
Initial conditions
The eCall capable MS is equipped with USIM subscription restricted to eCall only.
System Simulator
1 cell, default parameters, ciphering off
T3212 set to 252 Minutes. ATT flag set to 1 (IMSI ATTACH/DETACH shall be performed in the cell)
Mobile Station
The MS is equipped with a Test USIM containing default values except for those listed below.
USIM field
Contents
EFUST
Service n°2 Fixed Dialling Numbers (FDN) and Service n°89 eCall Data available
EFFDN
Display two FDNs, eCall Test Number (123456) and eCall reconfiguration number (345678)
EFEST
Enabled Services Table
Specific PICS statement(s)
-
Specific PIXIT statement(s)
-
Test procedure
a) MS is powered on. SS monitors to verify that MS does not attempt to register for a period of 120 seconds.
b) MS is made to initiate a Test eCall in accordance with manufacturer’s instructions. SS checks that MS performs registration before starting an Test eCall.
c) Having reached the active state, the call is cleared by the SS. SS monitors to verify that MS remains registered for the duration of T3243 and send LAU messages every 252 mins (as T3212 timer is set to 252 minutes).
d) Upon expiry of timer T3243 the MS shall perform IMSI detach.
Maximum Duration of Test
12 hours 20 minutes.
Expected Sequence:
Step
Direction
Message
Comments
1
MS
The MS is switched on.
2
SS
The SS verifies for 120 sec that the MS does not send RACH or any other message.
3
MS
MS is made to initiate a Test eCall (The first number stored in the EFFDN field)
4
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to Location updating.
5
SS->MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
LOCATION UPDATING REQUEST
"Location Updating Type" = Normal location updating/IMSI Attach.
7
SS->MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
9
SS -> MS
LOCATION UPDATING ACCEPT
10
MS -> SS
TMSI REALLOCATION COMPLETE
11
SS -> MS
CHANNEL RELEASE
12
MS->SS
CHANNEL REQUEST
The SS verifies that the MS sends RACH Request with "Establishment cause" set to “originating call”
13
SS->MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
CM SERVICE REQUEST
15
SS -> MS
CM SERVICE ACCEPT
16
MS -> SS
SETUP
Verify called number is the Test eCall number.
(The first number stored in the EFFDN field)
17
SS -> MS
CALL PROCEEDING
18
SS -> MS
ALERTING
19
MS
Depending on the PIXIT, an alerting indication is given.
20
SS -> MS
ASSIGNMENT COMMAND
21
MS -> SS
ASSIGNMENT COMPLETE
22
SS -> MS
CONNECT
23
MS -> SS
CONNECT ACKNOWLEDGE
24
MS
Traffic channel is kept active for at least 5 seconds.
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
29
SS
SS verifies that MS sends periodic Location Update Request every 252 minutes (5% margin is allowed).
30
SS
IMSI DETACH INDICATION
SS verifies that MS performs IMSI detach after T3243 expires. (After 12 hours of completing step 28). 1% margin is allowed
Specific Message Contents
None
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.7 Directed Retry / Mobile Originated Call
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.7.1 Conformance requirements
|
The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (with frequency hopping) or SDCCH/4 to TCH/F or TCH/H with or without frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "mobile originating call proceeding" state shall, upon receipt of a CONNECT message, attach the appropriate user connection to the radio path and return a CONNECT ACKNOWLEDGE message to the SS.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.4,
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1.6. and 9.1.15.
3GPP TS 04.13, subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.7.2 Test purpose
|
To test that, when the MS is ordered to perform a non-synchronized handover after the CALL PROCEED message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance information element in the PHYSICAL INFORMATION message into account. To test that the MS activates the new channel correctly and transmits the HANDOVER COMPLETE message without undue delay. To test that the call control entity of the Mobile Station in the "mobile originating call proceeding" state, upon receipt of a CONNECT message, attaches the appropriate user connection to the radio path and returns a CONNECT ACKNOWLEDGE message to the SS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.7.3 Method of test
|
Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = (See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = 3.
BS colour code, BCC = 0.
Band
Cell A
Cell B
Both Cells
BCCH ARFCN
Cell Allocation
BCCH ARFCN
Cell Allocation
Format
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291
274
260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291
Range 128
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338
321
307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338
Range 128
GSM 710
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 750
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241
167
141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241
Range 128
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114
40
14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114
Bitmap 0
DCS 1 800
747
734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844
764
739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
Range 512
PCS 1 900
647
634, 641, 647, 654, 659, 662, 666, 667, 673, 675, 679, 682, 691, 698, 729, 732, 744
664
639, 643, 646, 649, 656, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Range 512
The timebase of Cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For execution counter M = 1 a combined CCH/SDCCH is used.
For execution counter M = 2 a non-combined SDCCH is used.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
PIXIT statements:
- Way to indicate mobile originated alerting.
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
This procedure is repeated for execution counter M = 1..2.
A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is made to initiate a call on Cell A. After the SS has sent the CALL PROCEEDING message the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B. The MS shall then begin to send access bursts on the new DCCH (and optionally on the SACCH) to cell B. The SS observes the access bursts and after receiving n (n being arbitrarily chosen between values according to table 26.6‑2 of subclause 26.6.5) access bursts, the SS sends one PHYSICAL INFORMATION message with an arbitrarily chosen Timing Advance. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message before x ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS. After the successful handover procedure the SS sends the ALERTING message. The correct alerting indication shall be given to the user (only applicable if the MS supports this feature). The SS sends the CONNECT message indicating that the call has been answered. The appropriate bearer channel shall be through connected in both directions. The MS shall send then the CONNECT ACKNOWLEDGE message as the response on the CONNECT message. Having reached the active state, the call is cleared by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13. The value of "x" depends upon the target channel and is specified in the specific message contents section.
Maximum Duration of Test
2 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
The sequence is performed for execution counter M = 1..2 (unless a particular TCH is not supported).
Step
Direction
Message
Comments
1
--------
--------
A MO call is initiated on cell A.
2
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
3
SS -> MS
IMMEDIATE ASSIGNMENT
See specific message contents.
4
MS -> SS
CM SERVICE REQUEST
CM Service Type = Mobile Originating Call Establishment.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
MS -> SS
SETUP
11
SS -> MS
CALL PROCEEDING
12
SS -> MS
HANDOVER COMMAND
See specific message contents.
13
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND.
14
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
15
MS -> SS
SABM
Sent without information field.
16
SS -> MS
UA
17
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step 14.
18
SS -> MS
ALERTING
19
MS
Depending on the PIXIT, an alerting indication is given.
20
SS -> MS
CONNECT
21
MS -> SS
CONNECT ACKNOWLEDGE
22
MS
The appropriate bearer channel is through connected in both directions.
23
SS -> MS
DISCONNECT
24
MS -> SS
RELEASE
25
SS -> MS
RELEASE COMPLETE
26
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents For Mobiles Supporting Speech
M = 1:
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/F + ACCHs
- TDMA offset
Chosen arbitrarily.
- Timeslot number
Chosen arbitrarily but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Synchronization Indication IE is not included
Frequency list after time
- Frequency List
Encode frequencies as per the table below.
Channel Mode IE
Speech (full rate version 1 or half rate version 1).
Step 17: "x" = 500.
HANDOVER COMMAND
Band
Frequency Short List
BCCH Carrier Number
Format
ARFCNs
ARFCN
GSM 450
Range 128
260, 262, 264, 266, 268, 270, 272, 276, 279, 281, 283, 285, 287, 289, 291
274
GSM 480
Range 128
307, 309, 311, 313, 315, 317, 319, 323, 326, 328, 330, 332, 334, 336, 338
321
GSM 710
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
GSM 750
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
T-GSM 810
Range 128
451, 455, 459, 461, 467, 468, 475, 497, 498, 500, 501, 502, 503, 506, 508
477
GSM 850
Range 128
141, 145, 149, 151, 157, 158, 165, 187, 193, 200, 201, 202, 203, 235, 241
167
GSM 900
Range 128
14, 18, 22, 24, 30, 31, 38, 60, 66, 73, 74, 75, 76, 108, 114
40
DCS 1 800
Range 128
746, 779
764
PCS 1 900
Range 128
646, 679
664
M = 2:
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
L2 pseudo length
See the table below.
Channel Description
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Zero (this gives cyclic hopping).
Mobile Allocation
- Length
3 octets.
- Contents
See the table below.
IMMEDIATE ASSIGNMENT
Band
Mobile Allocation
L2 pseudo length
GSM 450
281, 283, 285
14 octets (11 + contents of the MA)
GSM 480
328, 330, 332
14 octets (11 + contents of the MA)
GSM 710
500, 501, 502
14 octets (11 + contents of the MA)
GSM 750
500, 501, 502
14 octets (11 + contents of the MA)
T-GSM 810
500, 501, 502
14 octets (11 + contents of the MA)
GSM 850
200, 201, 202
14 octets (11 + contents of the MA)
GSM 900
73, 74, 75
14 octets (11 + contents of the MA)
DCS 1 800
Indicates all of the CA of cell A except ARFCNs 747 and 767.
PCS 1 900
Indicates all of the CA of cell A except ARFCNs 647 and 667
HANDOVER COMMAND
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/H + ACCHs
- TDMA offset
Chosen arbitrarily.
- Timeslot number
Chosen arbitrarily but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1, 2.. 63).
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Cell Channel Description
Encode frequencies as per the table below
Mobile Allocation after time
indicates channels as per the table below only
Channel Mode IE
speech (full rate version 1 or half rate version 1).
Step 17: "x" = 750.
HANDOVER COMMAND
Band
BCCH Carrier Number
Cell Channel Description
Mobile Allocation after time
ARFCN
Format
ARFCNs
GSM 450
274
Range 128
274, 279, 281, 283, 285, 287, 289, 291
281, 283, 285
GSM 480
321
Range 128
321, 326, 328, 330, 332, 334, 336, 338
328, 330, 332
GSM 710
477
Range 128
477, 498, 500, 501, 502, 503, 506, 508
500, 501, 502
GSM 750
477
Range 128
477, 498, 500, 501, 502, 503, 506, 508
500, 501, 502
T-GSM 810
477
Range 128
477, 498, 500, 501, 502, 503, 506, 508
500, 501, 502
GSM 850
167
Range 128
167, 193, 200, 201, 202, 203, 235, 241
200, 201, 202
GSM 900
40
Bitmap 0
40, 66, 73, 74, 75, 76, 108, 114
73, 74, 75
DCS 1 800
764
Range 512
761, 764, 771, 779, 782, 791, 798, 829, 832
791, 798, 829
PCS 1 900
664
Range 512
661, 664, 671, 679, 682, 691, 698, 629, 632
679, 682, 691
Specific Message Contents For Mobiles not Supporting Speech
The message contents shall be the same as for a Mobile Station supporting speech, except for:
For M = 1 (TCH/F):
HANDOVER COMMAND
Information Element
value/remarks
Mode of first channel
Arbitrary from those supported (12, 6, 3.6 kbps).
For M = 2 (TCH/H):
HANDOVER COMMAND
Information Element
value/remarks
Mode of first channel
Arbitrary from those supported (6, 3.6 kbps).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.8 Directed Retry / Mobile Terminated Call
|
This test is applicable to all MS which support at least one MT circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.8.1 Conformance requirements
|
The MS shall correctly apply the Directed Retry procedure from SDCCH/8 (with frequency hopping) or SDCCH/4 to TCH/F or TCH/H with or without frequency hopping in the non-synchronized case during call establishment. The call control entity of the Mobile Station in the "call delivered" state shall, if the MS supports immediate connect, continue the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, send an ALERTING message. The MS indicates acceptance of a MT call by sending CONNECT.
For speech calls the mobile station shall attach the user connection at latest when sending the CONNECT message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.
For Data Calls the mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.4,
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.5, 5.2.2.6, 5.2.2.9 and 9.1.15.
3GPP TS 04.13, subclause 5.2.6.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.8.2 Test purpose
|
To test that when the MS is ordered to perform a non-synchronized handover after the CALL CONFIRM message, it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly takes the values of the Timing Advance information element in the PHYSICAL INFORMATION message into account. To test that the MS activates the new channel correctly and transmits the HANDOVER COMPLETE message without undue delay. To test that the call control entity of the Mobile Station in the "call delivered" state, if the MS supports immediate connect, continues the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, sends an ALERTING message. To test that the MS indicates acceptance of a MT call by sending CONNECT.
To test that for speech calls the mobile station attaches the user connection at latest when sending the CONNECT message, except if there is no compatible radio resource available at this time. To test that in this case the attachment is delayed until such a resource becomes available.
To test that for Data Calls the mobile station attaches the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.8.3 Method of test
|
Initial Conditions
System Simulator:
2 cells A and B with same LAI, default parameters, except:
Cell A has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = as defaults.
BS colour code, BCC = as defaults.
PLMN_PERM = 00001010.
Cell B has:
BCCH ARFCN = See the table below.
Cell Allocation = See the table below.
PLMN colour code, NCC = 3.
BS colour code, BCC = 0.
Band
Cell A
Cell B
Both Cells
BCCH ARFCN
Cell Allocation
BCCH ARFCN
Cell Allocation
Format
GSM 450
263
259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291
274
260, 262, 264, 266, 268, 270, 272, 274, 276, 279, 281, 283, 285, 287, 289, 291
Range 128
GSM 480
310
306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338
321
307, 309, 311, 313, 315, 317, 319, 321, 323, 326, 328, 330, 332, 334, 336, 338
Range 128
GSM 710
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 750
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
T-GSM 810
457
447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508
477
451, 455, 459, 461, 467, 468, 475, 477, 497, 498, 500, 501, 502, 503, 506, 508
Range 128
GSM 850
147
137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241
167
141, 145, 149, 151, 157, 158, 165, 167, 187, 193, 200, 201, 202, 203, 235, 241
Range 128
GSM 900
20
10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114
40
14, 18, 22, 24, 30, 31, 38, 40, 60, 66, 73, 74, 75, 76, 108, 114
Bitmap 0
DCS 1 800
747
734, 741, 747, 754, 759, 762, 766, 767, 773, 775, 779, 782, 791, 798, 829, 832, 844
764
739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
Range 512
PCS 1 900
647
634, 641, 647, 654, 659, 662, 666, 667, 673, 675, 679, 682, 691, 698, 729, 732, 744
664
639, 643, 646, 649, 656, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Range 512
The timebase of Cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For execution counter M = 1 a combined CCH/SDCCH is used.
For execution counter M = 2 a non-combined SDCCH is used.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- Speech supported for Half rate version 1 (GSM HR) (TSPC_AddInfo_Half_rate_version_1)
- Immediate connect supported for all circuit switched basic services. (TSPC_AddInfo_ImmConn)
PIXIT statements:
- Way to indicate alerting.
- Way to make the MS accept an incoming call after alerting.
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
This procedure is repeated for execution counter M = 1..2.
A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
The MS is paged on Cell A. The MS responds to the PAGING REQUEST message and establishes a mobile terminated call on Cell A. If the MS supports immediate connect, it continues the call establishment by through-connecting the traffic channel in both directions, or if the MS does not support immediate connect, it sends an ALERTING message. The MS indicates acceptance of a MT call by sending CONNECT.
After the MS has sent the CALL CONFIRMED message (if the MS supports immediate connect then the MS sends the CONNECT message after the CALL CONFIRMED message on the old channel) the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B. The MS shall then begin to send access bursts on the new DCCH (and optionally on the SACCH) to cell B. The SS observes the access bursts and after receiving n (n being arbitrarily chosen between values according to table 26.6‑2 of subclause 26.6.5) access bursts, the SS sends one PHYSICAL INFORMATION message with an arbitrarily chosen Timing Advance. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message before x ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS. After the successful handover procedure the MS sends the ALERTING message (if the MS runs the immediate connect procedure then the MS does not send an ALERTING message). The correct alerting indication shall be given to the user (only applicable if the MS supports the feature or if the MS is not using the immediate connect procedure). After the MS sent the CONNECT message the appropriate bearer channel shall be through connected in both directions. The SS sends then the CONNECT ACKNOWLEDGE message as the response on the CONNECT message. Having reached the active state, the call is cleared by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13. The value of "x" depends upon the target channel and is specified in the specific message contents section.
Maximum Duration of Test
2 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
The sequence is performed for execution counter M = 1..2 (unless a particular TCH is not supported).
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
Sent on the correct paging subchannel on cell A.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
See specific message contents.
4
MS -> SS
PAGING RESPONSE
Message is contained in SABM.
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
7
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
8
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
9
SS
SS starts ciphering.
10
SS -> MS
SETUP
11
MS -> SS
CALL CONFIRMED
If the MS supports immediate connect then branch A applies. If the MS does not support immediate connect then branch B applies
A12
MS -> SS
CONNECT
sent on the old channel
A13
SS -> MS
HANDOVER COMMAND
See specific message contents.
A14
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND. If the HANDOVER COMMAND includes a starting time IE then the first HANDOVER ACCESS message shall be transmitted in the indicated frame (unless the indicated frame is not used by that channel, in which case the next frame used by that channel shall be used).
A15
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
A16
MS -> SS
SABM
Sent without information field.
A17
SS -> MS
UA
A18
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step A15.
B12
SS -> MS
HANDOVER COMMAND
See specific message contents.
B13
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND. If the HANDOVER COMMAND includes a starting time IE then the first HANDOVER ACCESS message shall be transmitted in the indicated frame (unless the indicated frame is not used by that channel, in which case the next frame used by that channel shall be used).
B14
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS message. Timing Advance is arbitrarily chosen.
B15
MS -> SS
SABM
Sent without information field.
B16
SS -> MS
UA
B17
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step B14.
B18
MS -> SS
ALERTING
B19
MS
Gives an alerting indication as defined in a PIXIT statement is given by the MS
B20
MS
The MS is made to accept the call in the way described in a PIXIT statement
B21
MS -> SS
CONNECT
22
MS
If the call is a speech call, the TCH shall be through connected in both directions.
23
SS -> MS
CONNECT ACKNOWLEDGE
24
MS
If the call is a data call, the TCH shall be through connected in both directions.
25
SS -> MS
DISCONNECT
26
MS -> SS
RELEASE
27
SS -> MS
RELEASE COMPLETE
28
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents For Mobiles Supporting Speech
M = 1:
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
Single RF Channel.
- ARFCN
Chosen arbitrarily from the Cell Allocation of Cell B, but not the BCCH carrier of Cell B.
Synchronization Indication IE not included.
Mode of First Channel
Speech (full rate version 1 or half rate version 1).
Band
BCCH Carrier Number
GSM 450
274
GSM 480
321
GSM 710
477
GSM 750
477
T-GSM 810
477
GSM 850
167
GSM 900
40
DCS 1 800
764
PCS 1 900
664
Step A18 / B17: "x" = 500.
M = 2:
IMMEDIATE ASSIGNMENT
Information Element
value/remark
As default message contents except:
L2 pseudo length
See the table below
Channel Description
- Channel Type
SDCCH/8
- TDMA offset
As default message contents.
- Timeslot number
Arbitrary value, but not zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Mobile Allocation.
- HSN
Chosen arbitrarily from the set (1,2,..63).
Mobile Allocation
- Length
3 octets.
- Contents
Indicates only three frequencies, as per the table below
IMMEDIATE ASSIGNMENT
Band
Mobile Allocation
L2 pseudo length
GSM 450
281, 283, 285
14 octets (11 + contents of the MA)
GSM 480
328, 330, 332
14 octets (11 + contents of the MA)
GSM 710
500, 501, 502
14 octets (11 + contents of the MA)
GSM 750
500, 501, 502
14 octets (11 + contents of the MA)
T-GSM 810
500, 501, 502
14 octets (11 + contents of the MA)
GSM 850
200, 201, 202
14 octets (11 + contents of the MA)
GSM 900
73, 74, 75
14 octets (11 + contents of the MA)
DCS 1 800
773, 775, 779
PCS 1 900
673, 675, 679
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
3
- Base Station Colour Code
0
- BCCH Carrier Number
See the table below
Channel Description
- Channel Type
TCH/H + ACCHs
- TDMA offset
Chosen arbitrarily.
- Timeslot number
Chosen arbitrarily, but not Zero.
- Training Sequence Code
Chosen arbitrarily.
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Zero (this gives cyclic hopping).
Frequency List after time
- Frequency List
Encode the frequencies as per the table below.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
Mode of First Channel
Speech (full rate version 1 or half rate version 1).
Starting Time
Indicates the frame number of cell B. that will occur approximately 1,1 seconds (238 frames have elapsed) after the HANDOVER COMMAND is sent by cell A.
HANDOVER COMMAND
Band
BCCH Carrier Number
Cell Channel Description
ARFCN
Format
ARFCNs
GSM 450
274
Range 128
260, 262, 264, 266, 276, 279, 281, 283, 285, 287, 289, 291
GSM 480
321
Range 128
307, 309, 311, 313, 323, 326, 328, 330, 332, 334, 336, 338
GSM 710
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
GSM 750
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
T-GSM 810
477
Range 128
451, 455, 459, 461, 497, 498, 500, 501, 502, 503, 506, 508
GSM 850
167
Range 128
141, 145, 149, 151, 187, 193, 200, 201, 202, 203, 235, 241
GSM 900
40
Bitmap 0
14, 18, 22, 24, 60, 66, 73, 74, 75, 76,108, 114
DCS 1 800
764
Range 512
749, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844
PCS 1 900
664
Range 512
649, 658, 661, 664, 671, 679, 682, 691, 698, 729, 732, 744
Step A18 / B17: "x" = 750.
Specific Message Contents For Mobiles not Supporting Speech
The message contents shall be the same as for a Mobile Station supporting speech, except for:
For M = 1 (TCH/F):
HANDOVER COMMAND
Information Element
value/remarks
Mode of first channel
Arbitrary from those supported (12, 6, 3.6 kbps).
For M = 2 (TCH/H):
HANDOVER COMMAND
Information Element
value/remarks
Mode of first channel
Arbitrary from those supported (6, 3.6 kbps).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.9.9 Default contents of messages
|
ALERTING (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
User-user
Not checked
SS version
Not checked
ALERTING (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
ASSIGNMENT COMMAND
Information element
Value/remark
Description of the first channel
describes non-hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
Power Command
As in subclause 26.1.1
Frequency list
Omitted
Cell channel description
Omitted
Mode of the first channel
appropriate for one bearer capability chosen for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
ASSIGNMENT COMPLETE
Information element
Value/remark
RR cause
normal event
AUTHENTICATION REQUEST
Information element
Value/remark
Ciphering key sequence number
Arbitrary
Spare half octet
(spare bits)
Authentication parameter RAND
Arbitrary
AUTHENTICATION RESPONSE
Information element
Value/remark
Authentication parameter SRES
Correct for given SRES
CALL CONFIRMED
Information element
Value/remark
Repeat indicator
Omitted
Bearer capability 1
The bearer capability 1 information element shall be included if and only if at least one of the following cases holds:
‑ the mobile station wishes another bearer capability than that given by the bearer capability 1 information element of the incoming SETUP message;
‑ the bearer capability 1 information element received in the SETUP message is accepted and the "radio channel requirement" of the Mobile Station is other than "full rate support only mobile station".
- the bearer capability 1 information element received in the SETUP message indicates speech and is accepted and the Mobile Station supports other speech versions than GSM full rate version 1/ half rate version 1.
Bearer capability 2
Omitted
Cause
Omitted
CC Capabilities
may be present
CALL PROCEEDING
Information element
Value/remark
Repeat Indicator
Omitted
Bearer Capability 1
Omitted if the SETUP message did not specify in the bearer capability 1 IE a connection element value "both, transparent preferred" or "both, non- transparent preferred". Otherwise included; in that case the connection element specifies the value that is appropriate for the selected teleservice (either value "transparent" or value "non transparent (RLP)"), all other parameters are same as in the bearer capability 1 IE of the received SETUP message.
Bearer Capability 2
Omitted
Facility
Omitted
Progress indicator
Omitted
CHANNEL RELEASE
Information element
Value/remark
RR cause
Normal event
CHANNEL REQUEST
Information element
Value/remark
Establishment cause
Answer to paging (100)
Random reference
Arbitrary value of 5 bits length
CIPHERING MODE COMMAND
Information element
Value/remark
Cipher mode setting
algorithm identifier
indicates a supported algorithm
SC
Start ciphering
Cipher response
CR
IMEI must not be included
CIPHERING MODE COMPLETE
Information element
Value/remark
Mobile equipment identity
Omitted
CM SERVICE ACCEPT
Information element
Value/remark
none but message head
CM SERVICE REQUEST
Information element
Value/remark
CM service type
Mobile originating call establishment or packet mode connection establishment
Ciphering key sequence number
CKSN of the MS
Mobile station classmark 2
Not checked
Mobile identity
TMSI of MS
CONNECT (network to mobile station direction)
Information element
Value/remark
Facility
Omitted
Progress indicator
Omitted
Connected number
Omitted
Connected subaddress
Omitted
User-user
Omitted
CONNECT (mobile station to network direction)
Information element
Value/remark
Facility
Not checked
Connected subaddress
Not checked
User-user
Not checked
SS version
Not checked
CONNECT ACKNOWLEDGE
Information element
Value/remark
none but message head
DISCONNECT (network to mobile station direction)
Information element
Value/remark
Cause
Coding standard
GSM
Location
User
Cause value
Normal clearing
Facility
Omitted
Progress indicator
Omitted
User-user
Omitted
DISCONNECT (mobile station to network direction)
Information element
Value/remark
Cause
Coding standard
GSM
Location
User
Cause value
Normal clearing
Facility
Not checked
User-user
Not checked
SS version
Not checked
EMERGENCY SETUP
Information element
Value/remark
Bearer Capability
May be present or omitted. If present, it shall indicate speech, the appropriate speech version(s) and have the appropriate value of radio channel requirement field
IMMEDIATE ASSIGNMENT
Information element
Value/remark
Page mode
Normal paging
Channel description
describes a valid SDCCH+SACCH in non-hopping mode
Request reference
Random access information
As received from MS
N51, N32, N26
Corresponding to frame number of the CHANNEL REQUEST
Timing advance
Arbitrary
Mobile allocation
Empty (L=0)
Starting time
Omitted
PAGING REQUEST TYPE 1
Information element
Value/remark
L2 pseudo length
L2 pseudo length of the message
Page Mode
Normal Paging
Channels needed for Mobiles 1 and 2
channel (first)
any channel
channel (second)
any channel
Mobile identity 1
TMSI of MS under test
Mobile identity 2
Omitted
P1 rest octets
(spare octets)
PAGING RESPONSE
Information element
Value/remark
Ciphering key sequence number
Value assigned to MS in the initial conditions
Spare half octet
(spare bits)
Mobile station classmark 2
Not checked
Mobile identity
specifies TMSI of MS
RELEASE (network to mobile station direction)
Information element
Value/remark
Cause
Omitted
Second cause
Omitted
Facility
Omitted
User-user
Omitted
RELEASE (mobile station to network direction)
Information element
Value/remark
Cause
Not checked
Second cause
Not checked
Facility
Not checked
User-user
Not checked
SS version
Not checked
RELEASE COMPLETE (network to mobile station direction)
Information element
Value/remark
Cause
Omitted
Facility
Omitted
User-user
Omitted
RELEASE COMPLETE (mobile station to network direction)
Information element
Value/remark
Cause
Not checked
Facility
Not checked
User-user
Not checked
SS version
Not checked
SETUP (MS to SS)
Information element
Value/remark
BC Repeat indicator
Omitted
Bearer capability 1
Appropriate for the teleservice selected for the test
Bearer capability 2
Omitted
Facility
Not checked
Calling party subaddress
Not checked
Called party BCD number
As entered
Called party subaddress
Omitted
LLC repeat indicator
Omitted
Low layer compatibility I
Appropriate for teleservice selected for the test
Low layer compatibility II
Omitted
HLC repeat indicator
Omitted
High layer compatibility i
Appropriate for teleservice selected for the test
High layer compatibility ii
Omitted
User-user
Not checked
SS version
Not checked
CLIR suppression
Not checked
CC Capabilities
may be present
SETUP (SS to MS)
Information element
Value/remark
BC repeat indicator
Omitted
Bearer capability 1
Appropriate for teleservice selected for the test
Bearer capability 2
Omitted
Facility
Omitted
Progress indicator
Omitted
Signal
Omitted
Calling party BCD number
Omitted
Calling party subaddress
Omitted
Called party BCD number
Omitted
Called party subaddress
Omitted
LLC repeat indicator
Omitted
Low layer compatibility I
Appropriate for teleservice selected for the test
Low layer compatibility II
Omitted
HLC repeat indicator
Omitted
High layer compatibility i
Appropriate for the teleservice selected for the test
High layer compatibility ii
Omitted
User-user
Omitted
26.10 E-GSM or R-GSM or ER-GSM signalling
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.1 E-GSM or R-GSM or ER-GSM signalling / general considerations
|
Subclause 26.10 only applies to E-GSM, R-GSM and ER-GSM mobile stations. The details of frequencies used in different test cases are listed below.
Table 26.1: Frequencies used for E-GSM or R-GSM or ER-GSM signalling tests
Test Case
Frequencies used in the test case
E-GSM testing
R-GSM or ER-GSM testing
26.10.2.1
neighbour cell and serving cell: 0, 2, 26, 38, 990, 1003, 1005, 1020,
neighbour cell and serving cell: 0, 2, 26, 38, 960, 970, 990, 1020
26.10.2.2
single RF: 1015,
hopping RF's: 0, 80, 1005, 1010
single RF: 972,
hopping RF's: 0, 80, 958, 1010
26.10.2.3
k=1 hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 30, 40, 1010, 1015
c=5: 980, 991, 992, 993, 994, 1015
c=6: 20, 40, 66
k=2 hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 0, 30, 40, 1010, 1015
c=5: 990, 991, 992, 993, 994
c=6: 20, 40, 66
k=1 hopping RF's
c=1: 964, 969, 972
c=2: 73, 76, 80, 85, 90
c=3: 956, 959, 976, 980
c=4: 30, 40, 969, 972, 990, 1020
c=5: 956, 960, 963, 966, 969, 972
c=6: 20, 40, 66
k=2 hopping RF's
c=1: 964, 969, 972
c=2: 66, 73, 76, 79, 108
c=3: 960, 963, 978, 990
c=4: 0, 30, 40, 969, 972, 990, 1020
c=5: 962, 965, 968, 972
c=6: 20, 40, 66
26.10.2.4.1
Target cell BCCH: 40
k=1 hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 30, 40, 1010, 1015
c=5: 980, 991, 992, 993, 994, 1015
k=2 hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 30, 40, 1010, 1015
c=5: 980, 991, 992, 993, 994, 1015
c=6: 10, 40, 66
k=3 hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 30, 40, 1010, 1015
c=5: 990, 991, 992, 993, 994
c=6: 10, 40, 66
Target cell BCCH: 965
k=1 hopping RF's
c=1: 964, 969, 972
c=2: 73, 76, 79, 86, 97
c=3: 956, 960, 963, 970
c=4: 30, 40, 969, 972, 990, 1020
c=5: 956, 960, 964, 967, 970, 973
k=2 hopping RF's
c=1: 964, 969, 972
c=2: 73, 76, 79, 86, 97
c=3: 956, 960, 963, 970
c=4: 30, 40, 969, 972, 990, 1020
c=5: 956, 960, 964, 967, 970, 973
c=6: 10, 40, 66
k=3 hopping RF's
c=1: 964, 969, 972
c=2: 73, 76, 79, 108, 115
c=3: 960, 964, 969, 972
c=4: 30, 40, 969, 972, 990, 1020
c=5: 960, 963, 966, 969, 972
c=6: 10, 40, 66
26.10.2.4.2
Original cell BCCH: 20
Target cell BCCH: 40
hopping RF's: 1005, 1010, 1015
Original cell BCCH: 990
Target cell BCCH: 965
hopping RF's: 960, 970, 990
26.10.2.5
hopping RF's
c=1: 1005, 1010, 1015
c=2: 73, 74, 75, 76, 77
c=3: 980, 981, 982, 983
c=4: 30, 40, 1010, 1015
c=5: 990, 991, 992, 993, 994
c=6: 30, 50, 70
hopping RF's
c=1: 964, 969, 972
c=2: 73, 76, 79, 108, 114
c=3: 960, 964, 968, 972
c=4: 30, 40, 969, 972, 990, 1020
c=5: 960, 964, 967, 970, 972
c=6: 30, 50, 70
26.10.3.1
BCCH: 20
Immediate Assignment: 40
Assignment: 990
BCCH: 20
Immediate Assignment: 40
Assignment: 965
26.10.3.2
BCCH: 20
Immediate Assignment: 40
Assignment: 990
BCCH: 20
Immediate Assignment: 40
Assignment: 965
Conformance requirements of clause 26 fully apply to any mobile station (P-GSM, E-GSM, R-GSM, ER-GSM or DCS) in the whole supported band of the mobile station.
Besides, as an E-GSM or R-GSM or ER-GSM mobile station shall support the P-GSM band, it shall pass successfully every test of clause 26 under the described GSM 900 conditions.
The purpose of this extra section is to test the different procedures which may be impacted when some channel uses E‑GSM or R-GSM or ER-GSM frequency(ies).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2 E-GSM or R-GSM or ER-GSM signalling / RR
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.1 E-GSM or R-GSM or ER-GSM signalling / RR / Measurement
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.1.1 Conformance requirements
|
The MS shall continuously send MEASUREMENT REPORT messages on every SACCH blocks and the measurement valid indication shall be set to valid (0) within the second block at the latest. After 20 s the values in the MEASUREMENT REPORT message shall contain measurement results for the 6 th strongest cells belonging to the set of cells indicated either in SI5 and SI5bis messages or in SI5 and SI5ter messages.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.1.2 and 9.1.39,
3GPP TS 05.08 subclause 8.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.1.2 Test purpose
|
To test that, when the SS gives information about neighbouring cells indicated either in SI5 and SI5bis messages or in SI5 and SI5ter messages, the MS reports appropriate results.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.1.3 Method of test
|
Initial Conditions
System Simulator:
8 cells with the following settings:
E-GSM:
Transmitter
Level
NCC
BCC
ARFCN
Cell Identity
Serving, S1
‑60
1
3
002
0001H
Neighbour, N1
‑85
1
5
990
0002H
Neighbour, N2
‑80
1
7
1005
0003H
Neighbour, N3
‑75
1
1
000
0004H
Neighbour, N4
‑55
1
3
026
0005H
Neighbour, N5
‑50
1
5
1020
0006H
Neighbour, N6
‑45
1
7
038
0007H
Neighbour, N7
‑40
1
1
1003
0008H
R-GSM or ER-GSM:
Transmitter
Level
NCC
BCC
ARFCN
Cell Identity
Serving, S1
‑60
1
3
002
0001H
Neighbour, N1
‑85
1
5
990
0002H
Neighbour, N2
‑80
1
7
970
0003H
Neighbour, N3
‑75
1
1
000
0004H
Neighbour, N4
‑55
1
3
026
0005H
Neighbour, N5
‑50
1
5
1020
0006H
Neighbour, N6
‑45
1
7
038
0007H
Neighbour, N7
‑40
1
1
960
0008H
With the exception of the Cell Allocation, the rest of the parameters for all eight cells are the same as the default settings and default SYSTEM INFORMATION TYPE 1 to 4 message contents for cell A. The Cell Allocation for the serving cell is the same as the default setting for cell A. The Cell Allocations for the neighbour cells need have only one entry, consisting of the ARFCN of that cell's BCCH.
Mobile Station:
The MS is in the active state of a call (U10).
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
PIXIT statements:
Foreseen Final State of the MS
Active state of a call (U10).
Test Procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The test is performed for execution counter, c=1 to 9.
For c=1 to 6, the following procedure applies:
With the MS having a call in progress, the SS sends SYSTEM INFORMATION TYPE 5, 5bis and 6 on the SACCH. The MS shall send MEASUREMENT REPORTs back to the SS, and it shall be indicated in these that measurement results for the 6 strongest present carriers of the supported band have been obtained.
For c=7 to 9, the following procedure applies:
With the MS having a call in progress, the SS sends SYSTEM INFORMATION TYPE 5, 5ter and 6 on the SACCH. The MS shall send MEASUREMENT REPORTs back to the SS, and it shall be indicated in these that measurement results for the 6 strongest present carriers of the supported band have been obtained.
Maximum Duration of Test
8 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
This sequence is performed for execution counter, c= 1 to 9.
Since SYSTEM INFORMATION TYPE 5, SYSTEM INFORMATION TYPE 6 and MEASUREMENT REPORT are sent continuously, a table is not applicable in this test. The interval between 2 successive Layer 2 frames containing MEASUREMENT REPORTs shall not exceed one Layer 2 frame.
Specific Message Contents
E-GSM:
SYSTEM INFORMATION TYPE 5:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5.
Neighbour Cells Description
- EXT IND
- EXT IND= 1, for c= 1 to 6: Information Element carries only a part of the BA.
- EXT IND= 0, for c=7 to 9: Information Element carries the complete BA.
- BA-IND
0
for c=1, use range 128 to encode the following frequencies: (26, 38)
for c=2, use range 256 to encode the following frequencies (990, 1 003, 1 005)
for c=3, use range 512 to encode the following frequencies (520, 990, 1 003, 1 005, 1 020)
for c=4, use range 1 024 to encode the following frequencies (0, 26, 38, 990, 1 003, 1 005)
for c=5, use variable Bitmap to encode the following frequencies (0, 26, 38)
for c=6, use Bitmap 0 to encode the following frequencies (26)
for c=7, use range 512 to encode the following frequencies: (520, 990, 1020)
for c=8, use range 1024 to encode the following frequencies: (0, 26, 38, 990, 1005, 1020)
for c=9, use range 256 to encode the following frequencies: (38)
SYSTEM INFORMATION TYPE 5bis:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5bis.
Neighbour Cells Description
- EXT IND
Information Element carries only a part of the BA.
- BA-IND
0
for c=1, use range 512 to encode the following frequencies: (520, 990, 1 003, 1 005, 1 020)
for c=2, use range 128 to encode the following frequencies (0, 26, 38)
for c=3, use range 256 to encode the following frequencies (0, 26, 38)
for c=4, use range 1 024 to encode the following frequencies (520, 1 000)
for c=5, use range 128 to encode the following frequencies (884, 990, 1 003, 1 005)
for c=6, use range 512 to encode the following frequencies (520, 990, 1 003)
SYSTEM INFORMATION TYPE 5ter:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5ter.
Neighbour Cells Description
- multiband reporting
normal reporting of the six strongest cells, irrespective of the band used.
- BA-IND
0
for c=7, use range 1024 to encode the following frequencies (0,26,1003, 1005)
for c=8, use variable bitmap to encode the following frequencies (1000,1003)
for c=9,, use range 256 to encode the following frequencies (26, 1003, 1020)
SYSTEM INFORMATION TYPE 6:
Information Element
value/ remark
Protocol Discriminator
RR Management
Message Type
sys info 6
Cell Identity
default
LAI
default
Cell Options
- Power Control Indicator
Power Control Indicator is set
- DTX Indicator
MS shall not use DTX
- Radio-Link-Time-out
default
PLMN permitted
only NCC 1 permitted
MEASUREMENT REPORT:
Information Element
value/remark
Protocol Discriminator
RR Management
Transaction Identifier
0000
Message Type
MEASUREMENT REPORT
Measurement Results
BA-used
0
DTX-used
DTX was not used
RXLEV-FULL-SERVING-CELL
See note 1
RXLEV-SUB-SERVING-CELL
See note 1
MEAS-VALID
See note 3
RXQUAL-FULL-SERVING-CELL
See note 1
RXQUAL-SUB-SERVING-CELL
See note 1
NO-NCELL-M
n (see note 2)
RXLEV-NCELL‑1
See note 1
BCCH-FREQ-NCELL‑1
See note 2
BSIC-NCELL‑1
Corresponds to that of BCCH-FREQ-NCELL‑1
RXLEV-NCELL‑2
See note 1
BCCH-FREQ-NCELL‑2
See note 2
BSIC-NCELL‑2
Corresponds to that of BCCH-FREQ-NCELL‑2
RXLEV-NCELL‑3
See note 1
BCCH-FREQ-NCELL‑3
See note 2
BSIC-NCELL‑3
Corresponds to that of BCCH-FREQ-NCELL‑3
RXLEV-NCELL‑4
See note 1
BCCH-FREQ-NCELL‑4
See note 2
BSIC-NCELL‑4
Corresponds to that of BCCH-FREQ-NCELL‑4
RXLEV-NCELL‑5
See note 1
BCCH-FREQ-NCELL‑5
See note 2
BSIC-NCELL‑5
Corresponds to that of BCCH-FREQ-NCELL‑5
RXLEV-NCELL‑6
See note 1
BCCH-FREQ-NCELL‑6
See note 2
BSIC-NCELL‑6
Corresponds to that of BCCH-FREQ-NCELL‑6
NOTE 1: These actual values are not checked.
NOTE 2: ARFCN 2 is the serving cell carrier.
c=1 report on ARFCNs 26, 38, 990, 1 003, 1 005, 1 020, n=6
c=2 report on ARFCNs 26, 38, 990, 1 003, 1 005, 0, (1 020 stronger than 1 005 but not broadcasted in SYS INFO), n=6
c=3 report on ARFCNs 26, 38, 1 003, 1 005, 1 020, 0 (990 less strong, 520 DCS), n=6
c=4 report on ARFCNs 26, 38, 990, 1 003, 1 005, 0 (1 000 less strong, 520 DCS, 1 020 not broadcasted in SYS INFO), n=6
c=5 report on ARFCNs 26, 38, 990, 1 003, 1 005, 0 (884 DCS), n=6
c=6 report on ARFCNs 26, 990, 1 003, n=3
c=7 report on ARFCNs 26, 990, 1003, 1005, 1020, 0 (520 DCS), n=6
c=8 report on ARFCNs 26, 38, 1003, 1005, 1020, 0 (990 and 1000 less strong), n=6
c=9 report on ARFCNs 26,38, 1003, 1020, n=4.
NOTE 3: The Measurement Valid Indication shall be set to valid within the second SACCH block at the latest.
R-GSM or ER-GSM:
SYSTEM INFORMATION TYPE 5:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5.
Neighbour Cells Description
- EXT IND
- EXT IND= 1, for c=1 to 6: Information Element carries only a part of the BA.
- EXT IND= 0, for c=7 to 9: Information Element carries the BA.
- BA-IND
0
for c=1, use range 128 to encode the following frequencies: (26, 38)
for c=2, use range 256 to encode the following frequencies (960, 970, 990)
for c=3, use range 512 to encode the following frequencies (520, 960, 970, 990, 1020)
for c=4, use range 1 024 to encode the following frequencies (0, 26, 38, 960, 970, 990)
for c=5, use variable Bitmap to encode the following frequencies (0, 26, 38)
for c=6, use Bitmap 0 to encode the following frequencies (26)
for c=7, use range 512 to encode the following frequencies: (520, 990, 1020)
for c=8, use range 1024 to encode the following frequencies: (0, 26, 38, 970, 990, 1020)
for c=9, use range 256 to encode the following frequencies: (38)
SYSTEM INFORMATION TYPE 5bis:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5bis.
Neighbour Cells Description
- EXT IND
Information Element carries only a part of the BA.
- BA-IND
0
for c=1, use range 512 to encode the following frequencies: (520, 960, 970, 990, 1020)
for c=2, use range 128 to encode the following frequencies (0, 26, 38)
for c=3, use range 256 to encode the following frequencies (0, 26, 38)
for c=4, use range 1 024 to encode the following frequencies (520, 1 000)
for c=5, use variable Bitmap to encode the following frequencies (884, 960, 970, 990)
for c=6, use range 512 to encode the following frequencies (520, 960, 990)
SYSTEM INFORMATION TYPE 5ter:
Information Element
value/remark
Protocol Discriminator
RR management
Message Type
Sys Info 5ter.
Neighbour Cells Description
- multiband reporting
normal reporting of the six strongest cells, irrespective of the band used.
- BA-IND
0
for c=7, use range 1024 to encode the following frequencies (0, 26, 960, 970)
for c=8, use variable bitmap to encode the following frequencies (960, 1000)
for c=9,, use range 256 to encode the following frequencies (26, 960, 1020)
SYSTEM INFORMATION TYPE 6:
Information Element
value/ remark
Protocol Discriminator
RR Management
Message Type
sys info 6
Cell Identity
default
LAI
default
Cell Options
- Power Control Indicator
Power Control Indicator is set
- DTX Indicator
MS shall not use DTX
- Radio-Link-Time-out
default
PLMN permitted
only NCC 1 permitted
MEASUREMENT REPORT:
Information Element
value/remark
Protocol Discriminator
RR Management
Transaction Identifier
0000
Message Type
MEASUREMENT REPORT
Measurement Results
BA-used
1
DTX-used
DTX was not used
RXLEV-FULL-SERVING-CELL
See note 1
RXLEV-SUB-SERVING-CELL
See note 1
MEAS-VALID
See note 3
RXQUAL-FULL-SERVING-CELL
See note 1
RXQUAL-SUB-SERVING-CELL
See note 1
NO-NCELL-M
n (see note 2)
RXLEV-NCELL‑1
See note 1
BCCH-FREQ-NCELL‑1
See note 2
BSIC-NCELL‑1
Corresponds to that of BCCH-FREQ-NCELL‑1
RXLEV-NCELL‑2
See note 1
BCCH-FREQ-NCELL‑2
See note 2
BSIC-NCELL‑2
Corresponds to that of BCCH-FREQ-NCELL‑2
RXLEV-NCELL‑3
See note 1
BCCH-FREQ-NCELL‑3
See note 2
BSIC-NCELL‑3
Corresponds to that of BCCH-FREQ-NCELL‑3
RXLEV-NCELL‑4
See note 1
BCCH-FREQ-NCELL‑4
See note 2
BSIC-NCELL‑4
Corresponds to that of BCCH-FREQ-NCELL‑4
RXLEV-NCELL‑5
See note 1
BCCH-FREQ-NCELL‑5
See note 2
BSIC-NCELL‑5
Corresponds to that of BCCH-FREQ-NCELL‑5
RXLEV-NCELL‑6
See note 1
BCCH-FREQ-NCELL‑6
See note 2
BSIC-NCELL‑6
Corresponds to that of BCCH-FREQ-NCELL‑6
NOTE 1: These actual values are not checked.
NOTE 2: ARFCN 2 is the serving cell carrier.
c=1 report on ARFCNs: 26, 38, 960, 970, 990, 1020. n=6
c=2 report on ARFCNs: 26, 38, 960, 970, 990, 0. (1020 stronger than 970 but not broadcasted in SYS INFO). n=6
c=3 report on ARFCNs: 26, 38, 960, 970, 1020, 0. (990 less strong, 520 DCS). n=6
c=4 report on ARFCNs: 26, 38, 960, 970, 990, 0. (1000 less strong, 520 DCS, 1020 not broadcasted in SYS INFO). n=6
c=5 report on ARFCNs: 26, 38, 960, 970, 990, 0. (884 DCS). n=6
c=6 report on ARFCNs: 26, 960, 990. n=3
c=7 report on ARFCNs: 26, 960, 970, 990, 1020, 0 (520 DCS). n=6
c=8 report on ARFCNs: 26, 38, 960, 970, 1020, 0 (990 and 1000 less strong). n=6
c=9 report on ARFCNs: 26, 38, 960, 1020. n=4.
NOTE 3: The Measurement Valid Indication shall be set to valid within the second SACCH block at the latest.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.2 E-GSM or R-GSM or ER-GSM signalling / RR / Immediate assignment
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.2.1 Conformance requirement
|
Following a PAGING REQUEST message, the MS shall correctly set up an RR connection on a supported channel described in the IMMEDIATE ASSIGNMENT message, using some E-GSM or R-GSM or ER-GSM frequency.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.2.2 Test purpose
|
To verify that the MS can correctly set up a dedicated control channel when E-GSM or R-GSM or ER-GSM frequencies are used.
This tested for a SDCCH/8.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell.
E-GSM:
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
SYSTEM INFORMATION type 1 message contains the following frequencies in the Cell Channel Description IE: 0, 30, 40, 66, 80, 1 005, 1 010, 1 015 (use range 1 024 to encode).
BCCH carrier number 1 015.
R-GSM or ER-GSM:
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
SYSTEM INFORMATION type 1 message contains the following frequencies in the Cell Channel Description IE: 0, 30, 40, 66, 80, 958, 1010, 972 (use range 1 024 to encode).
BCCH carrier number 972.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
PIXIT statements:
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
This test procedure is performed twice.
The System Simulator pages the MS and after the MS has responded with a CHANNEL REQUEST message the SS assigns an SDCCH channel using some E-GSM or R-GSM or ER-GSM frequencies. The MS shall go to the correct channel and send a PAGING RESPONSE message. Then the SS initiates RR-release by sending a CHANNEL RELEASE message.
Maximum Duration of Test
15 seconds.
Expected Sequence
The sequence is performed for execution counter k = 1 to 2.
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
2
MS -> SS
CHANNEL REQUEST
cause "answer to paging"
3
SS -> MS
IMMEDIATE ASSIGNMENT
Channel Type: see below
4
MS -> SS
PAGING RESPONSE
Shall be sent on the correct channel
5
SS -> MS
CHANNEL RELEASE
Specific Message Contents
E-GSM:
IMMEDIATE ASSIGNMENT
As default except:
Information element
remark/value
Channel description
- Channel Type
SDCCH/8
- Timeslot number
arbitrary but not zero
- Training sequence code
arbitrary
- Hopping channel
k=1 Single RF
k=2 RF hopping channel
- Channel Selector
k=1 ARFCN=1 015
k=2 MAIO = arbitrarily chosen HSN arbitrary chosen from the set (1,..63)
Mobile allocation
k=1 empty
k=2 indicates the following frequencies (0, 80, 1 005, 1 010)
R-GSM or ER-GSM:
IMMEDIATE ASSIGNMENT
As default except:
Information element
remark/value
Channel description
- Channel Type
SDCCH/8
- Timeslot number
arbitrary but not zero
- Training sequence code
arbitrary
- Hopping channel
k=1 Single RF
k=2 RF hopping channel
- Channel Selector
k=1 ARFCN=972
k=2 MAIO = arbitrarily chosen HSN arbitrary chosen from the set (1,..63)
Mobile allocation
k=1 empty
k=2 indicates the following frequencies (0, 80, 958, 1010)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.3 E-GSM or R-GSM or ER-GSM signalling / RR / channel assignment procedure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.3.1 Conformance requirements
|
1. Upon receipt of the ASSIGNMENT COMMAND message, the mobile station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the main signalling links).
2. The MS shall apply the hopping frequencies specified in ASSIGNMENT COMMAND message in the mobile allocation or frequency list or frequency short list at the time accessing the new channel.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.3 and 9.1.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.3.2 Test purpose
|
1. To verify that upon receipt of an ASSIGNMENT COMMAND, the MS switches to the channel defined in the ASSIGNMENT COMMAND, establishes the link and sends an ASSIGNMENT COMPLETE message.
2. To verify that an MS, having received an ASSIGNMENT COMMAND, is able in case of frequency hopping to decode the mobile allocation and frequency list correctly and applies the specified frequencies.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state with a TMSI allocated.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The test procedure is performed 2 times.
The SS pages the MS and allocates an SDCCH. Then a channel is assigned with ASSIGNMENT COMMAND. Each time the MS shall switch to the assigned channel, establish the link and send an ASSIGNMENT COMPLETE message.
The SS initiates the channel release procedure.
Maximum Duration of Test
3 minutes.
Expected Sequence
The test sequence is performed for execution counter k=1 to 2.
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
Timeslot Number = n.
4
MS -> SS
PAGING RESPONSE
5
SS -> MS
ASSIGNMENT COMMAND
See specific message contents Timeslot Number = (n+1) mod 8
6
MS -> SS
ASSIGNMENT COMPLETE
Sent on the correct channel after establishment of the main signalling link. Steps 5 and 6 are repeated cmax times, where cmax is the number of frequency formats allowed for each value of k. Use repetition counter c: See specific message content.
7
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
E-GSM:
ASSIGNMENT COMMAND:
Information element
value/remark
Protocol Discriminator
RR
Skip indicator
0000
Message type
ASSIGNMENT COMMAND
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS or SDCCH/8 if not
- Timeslot number
arbitrary
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
arbitrarily chosen from the set (1,2...63)
Power Command
- Power level
Arbitrarily chosen
For k=1
Cell Channel Description IE is not included
Frequency list
for c=1, use range 128 to encode the following frequencies: (1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following frequencies (73, 74, 75, 76, 77)
for c=3, use range 512 to encode the following frequencies (980, 981, 982, 983)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following frequencies (980, 991, 992, 993, 994, 1 015) with an encoding origin set to 980
for c=6, use Bitmap 0 to encode the following frequencies (20, 40, 66)
For k=2
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following 13 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=4, use range 1 024 to encode the following 8 frequencies (0, 30, 40, 66, 80, 1 005, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=6, use Bitmap 0 to encode the following 12 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114)
For k = 2
Mobile Allocation
indicates the following the frequencies:
for c=1 (1 005, 1 010, 1 015)
for c=2 (73, 74, 75, 76, 77)
for c=3 (980, 981, 982, 983)
for c=4 (0, 30, 40, 1 010, 1 015)
for c=5 (990, 991, 992, 993, 994)
for c=6 (20, 40, 66)
Mode of the First channel
speech full rate version 1 for TCH/F except if speech is not supported: arbitrary from those supported
Starting Time
not included
R-GSM or ER-GSM:
ASSIGNMENT COMMAND:
Information element
value/remark
Protocol Discriminator
RR
Skip indicator
0000
Message type
ASSIGNMENT COMMAND
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS or SDCCH/8 if not
- Timeslot number
arbitrary
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
arbitrarily chosen from the set (1,2...63)
Power Command
- Power level
Arbitrarily chosen
For k=1
Cell Channel Description IE is not included
Frequency list
for c=1, use range 128 to encode the following frequencies: (964, 969, 972)
for c=2, use range 256 to encode the following frequencies (73, 76, 80, 85, 90)
for c=3, use range 512 to encode the following frequencies (956, 960, 976, 980)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following frequencies (956, 960, 963, 966, 969, 972) with an encoding origin set to 956
for c=6, use Bitmap 0 to encode the following frequencies (20, 40, 66)
For k=2
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=2, use range 256 to encode the following 13 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 978, 990)
for c=4, use range 1 024 to encode the following 10 frequencies (0, 30, 40, 66, 80, 964, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following 13 frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=6, use Bitmap 0 to encode the following 12 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114)
For k = 2
Mobile Allocation
indicates the following the frequencies:
for c=1 (964, 969, 972)
for c=2 (66, 73, 76, 79, 108)
for c=3 (960, 964, 978, 990)
for c=4 (0, 30, 40, 969, 972, 990, 1020)
for c=5 (962, 965, 968, 972)
for c=6 (20, 40, 66)
Mode of the First channel
speech full rate version 1 for TCH/F except if speech is not supported: arbitrary from those supported
Starting Time
not included
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4 E-GSM or R-GSM or ER-GSM signalling / RR / Handover
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.1 E-GSM or R-GSM or ER-GSM signalling / RR / Handover / Successful handover
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.1.1 Conformance requirements
|
The MS shall correctly apply the handover procedure from a channel without frequency hopping in the primary band to a channel with frequency hopping using P-GSM and E-GSM or P-GSM and R-GSM or ER-GSM frequencies whatever the coding used for the frequency hopping description.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.4 and 9.1.15.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.1.2 Test purpose
|
To check that the MS correctly performs a non-synchronized handover, from a non hopping primary band SDCCH to a hopping TCH or SDCCH using E-GSM or R-GSM or ER-GSM frequencies, whatever the coding used for the hopping sequence description and that it activates the new channel correctly.
This is tested in the following case:
E-GSM or R-GSM or ER-GSM signalling / Handover / successful / call under establishment / non-synchronized /:
- from SDCCH/8 to TCH/F if the MS supports a TCH;
- from SDCCH/8 to SDCCH/8 if not.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.1.3 Method of test
|
Initial Conditions
System Simulator:
E-GSM:
2 cells A and B with same LAI, default parameters;
except for Cell A: the broadcasted Cell Channel Description in SYSTEM INFORMATION type 1 message contains the following frequencies: 20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114 (encoded using Bit Map 0 format);
The broadcasted BCCH frequency list for Cell A in SYSTEM INFORMATION type 2 and 5 contains the following frequencies: 10, 20, 40, 80, 90, 100, 110 and 120 (encoded in Bit Map 0 format).
R-GSM or ER-GSM:
2 cells A and B with same LAI, default parameters;
except for Cell A: the broadcasted Cell Channel Description in SYSTEM INFORMATION type 1 message contains the following frequencies: 20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114 (encoded using Bit Map 0 format);
Except for Cell B: the BCCH carrier number is 965.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and camped on cell A.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated" with TMSI allocated and camped on cell B.
Test Procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The test procedure is performed 17 times.
A Mobile Originating Call is initiated on cell A. After the MS has sent the SETUP message (and before the last L2 frame carrying the SETUP message is acknowledged by the SS) the SS sends a HANDOVER COMMAND message, ordering the MS to switch to cell B.
The MS shall then begin to send access bursts on the new channel, a TCH/F if supported (see PICS) or an SDCCH if not, to cell B.
The SS observes the access bursts. After receiving n access bursts, n being randomly drawn between 10 and 20 for the TCH case, 2 and 5 for the SDCCH (see table 26.6‑2 of subclause 26.6.5), the SS sends one PHYSICAL INFORMATION message with a Timing Advance of 20 (see table 26.6‑1 of subclause 26.6.5).
The MS shall activate the channel in sending and receiving mode. Then the MS shall establish a signalling link using the correct timing advance. The MS shall be ready to transmit a HANDOVER COMPLETE message before x ms after the end of the PHYSICAL INFORMATION message but not before a UA frame has been sent by the SS. The MS shall then again send the SETUP message to the SS, using the same value in the N(SD) field. Finally the SS sends a CHANNEL RELEASE to end the test.
The term "ready to transmit" is specified in 3GPP TS 04.13. The value of "x" depends upon the target channel:
- case SDCCH/8 x = 750;
- case TCH/F x=500.
Maximum Duration of Test
10 minutes.
Expected Sequence
The sequence is performed for execution counter k=1 to 3 and c=1 to 6 (excluding k=1 and c=6 as Format Bit Map 0 is not supported in the Frequency Short List IE).
Step
Direction
Message
Comments
1
--------
--------
A MO call is initiated on cell A
2
MS -> SS
CHANNEL REQUEST
Establ. Cause = "Originating call, NECI not set to 1
3
SS -> MS
IMMEDIATE ASSIGNMENT
see specific message contents
4
MS -> SS
CM SERVICE REQUEST
CM Service Type = Mobile Originating Call Establishment.
5
SS -> MS
CIPHERING MODE COMMAND
6
MS -> SS
CIPHERING MODE COMPLETE
7
MS -> SS
SETUP
Last L2 frame not acknowledged by the SS.
8
SS -> MS
HANDOVER COMMAND
see specific message contents
9
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND
10
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS. Timing Advance: 20
11
MS -> SS
SABM
Sent without information field
12
SS -> MS
UA
13
MS -> SS
HANDOVER COMPLETE
This message shall be ready to be transmitted before "x" ms after the completion of step 10
14
MS -> SS
SETUP
Same N(SD) as in step 7.
15
SS -> MS
CHANNEL RELEASE
Specific Message Contents
E-GSM:
IMMEDIATE ASSIGNMENT
Information Element
Value/remark
As default message contents, except:
Channel Description
- Channel type
SDCCH/8
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
Single RF channel
- ARFCN
Chosen arbitrarily from the Cell Allocation of Cell A, but not the BCCH carrier of Cell A.
HANDOVER COMMAND
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
40
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS or SDCCH/8 if not
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
arbitrarily chosen from the set (1,2...63)
Synchronization Indication IE is not included
For k = 1,
Cell Channel Description IE is not included
Frequency short list
for c=1, use range 128 to encode the following frequencies: (1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following frequencies (73, 74, 75, 76, 77)
for c=3, use range 512 to encode the following frequencies (980, 981, 982, 983)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following frequencies (980, 991, 992, 993, 994, 1 015)
For k=2
Cell Channel Description IE is not included
Frequency list
for c=1, use range 128 to encode the following frequencies: (1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following frequencies (73, 74, 75, 76, 77)
for c=3, use range 512 to encode the following frequencies (980, 981, 982, 983)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following frequencies (980, 991, 992, 993, 994, 1 015)
for c=6, use Bitmap 0 to encode the following frequencies (10, 40, 66)
For k=3
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following 13 frequencies (10, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=4, use range 1 024 to encode the following 10 frequencies (0, 30, 40, 66, 80, 520, 975, 1 005, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following 13 frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=6, use Bitmap 0 to encode the following 12 frequencies (10, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114)
For k = 3
Mobile Allocation
indicates the following the frequencies:
for c=1 (1 005, 1 010, 1 015)
for c=2 (73, 74, 75, 76, 77)
for c=3 (980, 981, 982, 983)
for c=4 (30, 40, 1 010, 1 015)
for c=5 (990, 991, 992, 993, 994)
for c=6 (10, 40, 66)
Mode of the First channel
if SDCCH/8: signalling
if TCH/F: speech full rate version 1 if speech is supported, otherwise arbitrary from those supported
R-GSM or ER-GSM:
IMMEDIATE ASSIGNMENT
Information Element
Value/remark
As default message contents, except:
Channel Description
- Channel type
SDCCH/8
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
Single RF channel
- ARFCN
Chosen arbitrarily from the Cell Allocation of Cell A, but not the BCCH carrier of Cell A.
HANDOVER COMMAND
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
965
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS or SDCCH/8 if not
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
arbitrarily chosen from the set (1,2...63)
Synchronization Indication IE is not included
For k = 1,
Cell Channel Description IE is not included
Frequency short list
for c=1, use range 128 to encode the following frequencies: (964, 969, 972)
for c=2, use range 256 to encode the following frequencies (73, 76, 79, 86, 97)
for c=3, use range 512 to encode the following frequencies (956, 960, 964, 970)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following frequencies (956, 960, 964, 967, 970, 973)
For k=2
Cell Channel Description IE is not included
Frequency list
for c=1, use range 128 to encode the following frequencies: (964, 969, 972)
for c=2, use range 256 to encode the following frequencies (73, 76, 79, 86, 97)
for c=3, use range 512 to encode the following frequencies (956, 960, 963, 970)
for c=4, use range 1 024 to encode the following frequencies (30, 40, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following frequencies (956, 960, 964, 967, 970, 973)
for c=6, use Bitmap 0 to encode the following frequencies (10, 40, 66)
For k=3
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=2, use range 256 to encode the following 13 frequencies (10, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=4, use range 1 024 to encode the following 12 frequencies (0, 30, 40, 66, 80, 520, 955, 964, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=6, use Bitmap 0 to encode the following 12 frequencies (10, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114)
For k = 3
Mobile Allocation
indicates the following the frequencies:
for c=1 (964, 969, 972)
for c=2 (73, 76, 79, 108, 115)
for c=3 (960, 964, 969, 972)
for c=4 (30, 40, 969, 972, 990, 1020)
for c=5 (960, 963, 966, 969, 972)
for c=6 (10, 40, 66)
Mode of the First channel
if SDCCH/8: signalling
if TCH/F: speech full rate version 1 if speech is supported, otherwise arbitrary from those supported
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.2 E-GSM or R-GSM or ER-GSM signalling / RR / Handover / layer 1 failure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.2.1 Conformance requirements
|
During a handover from a channel in the E-GSM or R-GSM or ER-GSM band to a channel in the P-GSM band, or the contrary, the MS shall correctly return to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.2.2 Test purpose
|
To check that the MS correctly returns to the old channel in the case of a handover failure caused by a layer 1 failure on the target cell, even if the origin is in the P-GSM band and the target in the E-GSM or R-GSM or ER-GSM band.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.4.2.3 Method of test
|
Initial Conditions
System Simulator:
E-GSM:
2 cells with same LAI, default parameters.
Cell A: The broadcasted BCCH frequency list for Cell A in SYSTEM INFORMATION type 2 and 5 contains the following frequencies: 10, 20, 40, 80, 90, 100, 110 and 120 (encoded in Bit Map 0 format).
The BCCH carrier number of Cell B is 40. (According to Table 26.1)
R-GSM or ER-GSM:
2 cells with same LAI, default parameters, except the BCCH carrier number of Cell A is 990, the BCCH carrier number of Cell B is 965.
Mobile Station:
E-GSM:
The MS is in the active state (U10) of a call on a P-GSM channel of cell A. power level = 10.
R-GSM or ER-GSM:
The MS is in the active state (U10) of a call on a E-GSM channel of cell A, power level = 10.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen Final State of the MS
The active state (U10) of a mobile call (on cell A), used power level 10.
Test Procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The MS is in the active state (U10) of a call on a P-GSM channel (on an E-GSM channel for R-GSM or ER-GSM testing) of cell A (used power level 10). The SS sends a HANDOVER COMMAND on the main DCCH. The MS shall begin to send access bursts at the commanded power level on the new DCCH (and optionally on SACCH) to cell B (power level 12). With the exception of normal BCCH signalling, the SS does not transmit anything on cell B (thus causing a time-out of T3124). The MS shall re-establish the old link on cell A and send a HANDOVER FAILURE within 3 seconds from the transmission of HANDOVER COMMAND, using the old power level.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
SS -> MS
HANDOVER COMMAND
to an E-GSM or R-GSM or ER-GSM channel see specific message contents
2
MS -> SS
HANDOVER ACCESS
Several messages are sent, all with correct Handover References.
3
MS -> SS
HANDOVER FAILURE
Sent on old channel, RR cause value = "Abnormal release, unspecified", "Abnormal release, channel unacceptable", "Abnormal release, timer expired", "Abnormal release, no activity on the radio path" or "Protocol error unspecified". Layer 1 header has the same power level as the layer 1 header in step 1. Shall be sent within 3 seconds from the transmission of HANDOVER COMMAND.
Specific Message Contents
E-GSM:
HANDOVER COMMAND
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
40
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
chosen randomly from the set (1,2...63)
Synchronization Indication IE is not included
Cell Channel Description IE is not included
Frequency short list
use range 128 to encode the following frequencies: (1 005, 1 010, 1 015)
Mode of the first channel
Full rate speech version 1 if supported. If not, arbitrary from those supported except signalling.
R-GSM or ER-GSM:
HANDOVER COMMAND
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
965
Channel Description
- Channel type
TCH/F + ACCHs if supported by the MS
- Timeslot number
arbitrary but not zero
- Training sequence code
chosen arbitrarily
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
chosen randomly from the set (1,2...63)
Synchronization Indication IE is not included
Cell Channel Description IE is not included
Frequency short list
use range 128 to encode the following frequencies: (960, 970, 990)
Mode of the first channel
Full rate speech version 1 if supported. If not, arbitrary from those supported except signalling.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.5 E-GSM or R-GSM or ER-GSM signalling / RR / Frequency Redefinition
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.5.1 Conformance requirements
|
1) To verify that the MS, after receiving a FREQUENCY REDEFINITION message, correctly starts using the new frequencies, and hopping sequence when some E-GSM or R-GSM or ER-GSM frequencies are used.
2) The last received Cell Channel Description information element is used to decode the Mobile Allocation IE received on the FREQUENCY REDEFINITION message.
References
3GPP TS 04.08 / 3GPP TS 44.018, subclauses 3.4.5 and 9.1.13.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.5.2 Test purpose
|
1) To verify that the MS, after receiving a FREQUENCY REDEFINITION message, starts using the new frequencies and hopping sequence when some E-GSM or R-GSM or ER-GSM frequencies are used.
2) To check that the last received Cell Channel Description information element is used to decode the Mobile Allocation IE received in the FREQUENCY REDEFINITION message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.2.5.3 Method of test
|
Initial conditions
System Simulator:
1 cell; default parameters.
Mobile Station:
The MS is in "idle, updated" state with TMSI allocated.
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Foreseen final state of the MS
"Idle, updated", with TMSI allocated.
Test procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The test procedure is performed six times.
The System Simulator pages the MS and after the MS has responded with a CHANNEL REQUEST, the simulator assigns a TCH/F if supported otherwise a SDCCH/8. Then the SS sends to MS a FREQUENCY REDEFINITION. The MS shall then use the new frequencies/hopping sequence.
Maximum duration of test
3 minutes.
Expected sequence
The sequence is performed for execution counter c=1 to 6.
Step
Direction
Message
Comments
1
SS->MS
PAGING REQUEST TYPE 1
2
MS->SS
CHANNEL REQUEST
3
SS->MS
IMMEDIATE ASSIGNMENT
Hopping channel,
Channel type = TCH/F if a TCH is supported otherwise, Channel type=SDCCH/8.
4
MS->SS
PAGING RESPONSE
Sent on the correct channel after establishment of the main signalling link
5
SS->MS
FREQUENCY REDEFINITION
See specific message contents.
6
-----
------------------
The SS checks that the MS is transmitting on the correct frequencies.
7
SS->MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents
E-GSM:
FREQUENCY REDEFINITION
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
40
Channel Description
- Channel type
Same as in IMMEDIATE ASSIGNMENT
- Timeslot number
Same as in IMMEDIATE ASSIGNMENT
- Training sequence code
Same as in IMMEDIATE ASSIGNMENT
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
Same as in IMMEDIATE ASSIGNMENT
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=2, use range 256 to encode the following 13 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=4, use range 1 024 to encode the following 8 frequencies (0, 30, 40, 66, 80, 1 005, 1 010, 1 015)
for c=5, use variable Bitmap to encode the following frequencies (980, 981, 982, 983, 990, 991, 992, 993, 994, 1 000, 1 005, 1 010, 1 015)
for c=6, not present (the mobile station will use the last Cell Channel Description IE received, i.e. the one broadcast in the SYSTEM INFORMATION TYPE 1 message).
Mobile Allocation
indicates the following frequencies:
for c=1 (1 005, 1 010, 1 015)
for c=2 (73, 74, 75, 76, 77)
for c=3 (980, 981, 982, 983)
for c=4 (30, 40, 1 010, 1 015)
for c=5 (990, 991, 992, 993, 994)
for c=6 (30, 50, 70)
Starting time
indicates (current frame number + 100 frames) mod 42432
R-GSM or ER-GSM:
FREQUENCY REDEFINITION
Information Element
Value/remark
As default message contents, except:
Cell Description
- BCCH carrier number
40
Channel Description
- Channel type
Same as in IMMEDIATE ASSIGNMENT
- Timeslot number
Same as in IMMEDIATE ASSIGNMENT
- Training sequence code
Same as in IMMEDIATE ASSIGNMENT
- Hopping
RF hopping channel
- MAIO
arbitrary
- HSN
Same as in IMMEDIATE ASSIGNMENT
Cell Channel Description
for c=1, use range 128 to encode the following 13 frequencies: (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=2, use range 256 to encode the following 13 frequencies (20, 40, 66, 73, 74, 75, 76, 77, 78, 79, 108, 114, 115)
for c=3, use range 512 to encode the following 13 frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=4, use range 1 024 to encode the following 10 frequencies (0, 30, 40, 66, 80, 964, 969, 972, 990, 1020)
for c=5, use variable Bitmap to encode the following 13 frequencies (960, 961, 962, 963, 964, 965, 966, 967, 968, 969, 970, 971, 972)
for c=6, not present (the mobile station will use the last Cell Channel Description IE received, i.e. the one broadcast in the SYSTEM INFORMATION TYPE 1 message).
Mobile Allocation
indicates the following frequencies:
for c=1 (964, 969, 972)
for c=2 (73, 76, 79, 108, 114)
for c=3 (960, 964, 968, 972)
for c=4 (30, 40, 969, 972, 990, 1020)
for c=5 (960, 964, 967, 970, 972)
for c=6 (30, 50, 70)
Starting time
indicates (current frame number + 100 frames) mod 42432
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3 E-GSM or R-GSM or ER-GSM signalling / Structured procedure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.1 E-GSM or R-GSM or ER-GSM signalling / Structured procedure / Mobile originated call
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.1.1 Conformance requirement
|
1) An MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS , shall start to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.
2) Upon receipt of the ASSIGNMENT COMMAND message, the Mobile Station initiates a local end release of link layer connections, disconnects the physical channels, commands the switching to the assigned channels and initiates the establishment of lower layer connections (this includes the activation of the channels, their connection and the establishment of the data links). After the main signalling link is successfully established, the MS returns an ASSIGNMENT COMPLETE message, specifying cause "normal event", to the network on the main DCCH.
3, 4) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:
- attach the user connection to the radio path;
- return a CONNECT ACKNOWLEDGE message.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.3.1 and 3.4.3.2.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3.
Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.1.6.
Conformance requirement 5: 3GPP TS 02.07.
Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1.1.6 and 5.1.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.1.2 Test purpose
|
1) To verify that the MS in MM state "idle, updated" and in RR idle mode with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message.
2) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed authentication and cipher mode setting procedures, after having sent a SETUP message, after having received a CALL PROCEEDING message followed by an ALERTING message and an ASSIGNMENT COMMAND message allocating an appropriate TCH, the MS sends an ASSIGNMENT COMPLETE message.
3) To verify that subsequently, after the suite of actions specified in test purposes 1 and 2, the MS after receiving a CONNECT message returns a CONNECT ACKNOWLEDGE message.
4) To verify that after the suite of actions specified in test purposes 1 and 2, the MS after receiving a CONNECT message attaches the user connection to the radio path. (This is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.1.3 Method of test
|
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band)
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
- Way to indicate mobile originated alerting.
-. Way to display the called number
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen Final State of the MS
The MS is in MM state "idle updated".
Test procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The following test is performed for one teleservice supported by the MS:
- A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.
- The MS is made to initiate a call. The call is established with late assignment. The release of the call is initiated by the MS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" is entered
3
MS
4
MS -> SS
CHANNEL REQUEST
Establishment cause is "originating call and the network does not set the NECI bit to 1".
5
SS -> MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM.
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
SRES specifies correct value.
9
SS -> MS
CIPHERING MODE COMMAND
SS starts deciphering after sending the message.
10
MS -> SS
CIPHERING MODE COMPLETE
Shall be sent enciphered. All following messages shall be sent enciphered.
11
SS
SS starts ciphering.
12
MS -> SS
SETUP
13
SS -> MS
CALL PROCEEDING
14
SS -> MS
ALERTING
15
MS
Depending on the PICS, an alerting indication is given.
16
SS -> MS
ASSIGNMENT COMMAND
17
MS -> SS
ASSIGNMENT COMPLETE
18
SS -> MS
CONNECT
19
MS -> SS
CONNECT ACKNOWLEDGE
20
MS
The appropriate bearer channel is through connected in both directions.
21
MS
If the call is a data call, the TCH shall be through connected in both directions.
22
MS
The MS is made to release the call.
23
MS -> SS
DISCONNECT
24
SS -> MS
RELEASE
25
MS -> SS
RELEASE COMPLETE
26
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.2 E-GSM or R-GSM or ER-GSM signalling / Structured procedures / emergency call
|
Emergency call establishment can be initiated by an MS whether location updating has been successful or not and whether a SIM is inserted into the MS or not; but only if the MS is equipped for speech.
This subclause is only applicable to an MS supporting speech.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.2.1 Conformance requirement
|
1) The MS in the "idle, updated" state, as after a successful location update, after the number 112 has been entered by user, shall send a CHANNEL REQUEST message with correct establishment cause ("emergency call").
2) After assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel shall be a CM SERVICE REQUEST message specifying the correct IMEI and a non-available CKSN, with CM Service Type "emergency call establishment".
3) After cipher mode setting acceptance by the network, the MS shall send an EMERGENCY SETUP message.
4, 5) The emergency call shall be correctly established. The assignment procedure shall be correctly performed.
6) After receipt of a CONNECT ACKNOWLEDGE message during correct establishment of the emergency call the TCH shall be through connected in both directions if an appropriate TCH is available.
7) The call shall be cleared correctly.
Requirement Reference:
For conformance requirement 1 and 2:
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1;
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1 and 4.5.1.5;
3GPP TS 02.30 clause 4.
For conformance requirement 3:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.2.
For conformance requirements 4 and 5:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.1; and
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3.
For conformance requirement 6:
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.1.6 and 5.1.3.
For conformance requirement 7:
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.2.2 Test purpose
|
1) To verify that the MS in the "idle, no IMSI" state (no SIM inserted) when made to call the number 112, sends a CHANNEL REQUEST message with establishment cause "emergency call".
2) To verify that after assignment of a dedicated channel the first layer message sent by the MS on the assigned dedicated channel is a CM SERVICE REQUEST message specifying the correct CKSN and TMSI, with CM Service Type "emergency call establishment".
3) To verify that after receipt of a CM SERVICE ACCEPT message from the SS, the MS sends an EMERGENCY SETUP message.
4) To verify that subsequently, the SS having sent a CALL PROCEEDING message and then an ALERT message and having initiated the assignment procedure, the MS performs correctly that assignment procedure.
5) To verify subsequent correct performance of a connect procedure.
6) To verify that subsequently the MS has through connected the TCH in both directions.
7) To verify that the call is cleared correctly.
This is tested in the following case:
Structured procedures / emergency call / idle, no IMSI / accept case.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.2.3 Method of test
|
Specific PICS statements:
- R-GSM Band (TSPC_Type_GSM_R_Band)
- ER-GSM Band (TSPC_Type_ER_GSM_Band )
- TSPC_AddInfo_Full_rate_version_1
PIXIT statements:
-
Initial Conditions
System Simulator:
1 cell, default parameters except:
See Table 26.1
Mobile Station:
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Foreseen Final State of the MS
The MS is in MM-state "idle, no IMSI", no SIM inserted.
Test procedure
If the MS is R-GSM or ER-GSM capable, then this test shall be performed using R-GSM or ER-GSM, otherwise this test shall be performed using E-GSM.
The MS is made to initiate an emergency call. The call is established without authentication, without ciphering, with early assignment. Having reached the active state, the call is cleared by the SS.
Maximum Duration of Test
1 minute.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The "called number" 112 is entered
2
MS -> SS
CHANNEL REQUEST
Establishment cause is "emergency call".
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
Message is contained in SABM. The CM service type IE indicates "emergency call establishment". The mobile identity IE specifies the IMEI of the MS. The cipher key sequence number IE indicates "no key is available". The mobile station classmark IE is as specified by the manufacturer in a PICS/PIXIT statement.
5
SS -> MS
CM SERVICE ACCEPT
6
MS -> SS
EMERGENCY SETUP
7
SS -> MS
CALL PROCEEDING
8
SS -> MS
ASSIGNMENT COMMAND
The rate of the channel is one indicated by the EMERGENCY SETUP message.
9
MS -> SS
ASSIGNMENT COMPLETE
10
SS -> MS
ALERTING
11
SS -> MS
CONNECT
12
MS -> SS
CONNECT ACKNOWLEDGE
13
MS
The TCH is through connected in both directions.
14
SS -> MS
DISCONNECT
15
MS -> SS
RELEASE
16
SS -> MS
RELEASE COMPLETE
17
SS -> MS
CHANNEL RELEASE
The main signalling link is released.
Specific Message Contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.3.3 Default contents of messages
|
Same as in subclause 26.9.7 except for the following.
ASSIGNMENT COMMAND
E-GSM:
Information element
Value/remark
Description of the first channel
describes non-hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
ARFCN = 990
Power Command
-
Chosen arbitrarily but within the range supported by the MS.
Frequency list
Omitted
Cell channel description
Omitted
Mode of the first channel
appropriate for one bearer capability chosen for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
R-GSM or ER-GSM:
Information element
Value/remark
Description of the first channel
describes non-hopping Bm+ACCHs or Lm+ACCHs as appropriate for the test
ARFCN = 965
Power Command
-
Chosen arbitrarily but within the range supported by the MS.
Frequency list
Omitted
Cell channel description
Omitted
Mode of the first channel
appropriate for one bearer capability chosen for the test
Description of the second channel
Omitted
Mode of the second channel
Omitted
Mobile allocation
Omitted
Starting time
Omitted
Cipher mode setting
Omitted
IMMEDIATE ASSIGNMENT
Information element
Value/remark
Page mode
Normal paging
Channel description
describes a valid SDCCH+SACCH in non-hopping mode
ARFCN = 40
Request reference
Random access information
As received from MS
N51, N32, N26
Corresponding to frame number of the CHANNEL REQUEST
Timing advance
Arbitrary
Mobile allocation
Empty (L=0)
Starting time
Omitted
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.10.4 E-GSM or R-GSM or ER-GSM signalling / Default message contents
|
Default SYSTEM INFORMATION:
NOTE: SYSTEM INFORMATION 7, and SYSTEM INFORMATION 8 messages are not used.
SYSTEM INFORMATION type 1 message
Information elements
Value/Remark
Cell Channel Description
For Cell A
- Format identifier
Bit Map 0
- Cell Allocation ARFCN
Channel Numbers 20, 30, 50 and 70.
For Cell B
- Format identifier
Bit Map 0
- Cell Allocation ARFCN
Channel Numbers 10, 12, 40, 60, 62, 63
RACH Control parameters
see below
SI1 Rest octets
see below
SYSTEM INFORMATION type 2 message
Information elements
Value/Remark
BCCH frequency list
For cell A
- Format identifier
bit map 0
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 10, 20, 80, 90, 100, 110 and 120
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
bit map 0
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 10, 36, 40, 114, 118
- EXT-IND
This IE does not carry the complete BA
NCC permitted
see below
RACH control parameters
see below
SYSTEM INFORMATION type 2bis message
E-GSM:
Information elements
Value/Remark
Extended BCCH frequency list
For cell A
- Format identifier
range 256
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
988, 990, 1 003
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
range 128
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 1 005, 1 010, 1 015
- EXT-IND
This IE does not carry the complete BA
RACH control parameters
see below
SI 2bis rest octets
see below
R-GSM or ER-GSM:
Information elements
Value/Remark
Extended BCCH frequency list
For cell A
- Format identifier
range 256
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
962, 965, 968, 980, 990
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
range 128
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 969, 970, 972, 1005, 1010
- EXT-IND
This IE does not carry the complete BA
RACH control parameters
see below
SI 2bis rest octets
see below
SYSTEM INFORMATION type 3 message
Information elements
Value/Remark
Cell identity
see below
LAI
see below
Control channel description
see below
Cell options
see below
Cell Selection parameters
see below
RACH control parameter
see below
SI3 Rest octets
see below
SYSTEM INFORMATION type 4 message
Information elements
Value/Remark
LAI
see below
Cell selection parameters
see below
RACH control parameters
see below
CBCH Channel Description
see below
CBCH MA
see below
SI4 Rest octets
see below
SYSTEM INFORMATION type 5 message
Information elements
Value/Remark
BCCH frequency list
For cell A
- Format identifier
bit map 0
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 10, 20, 80, 90, 100, 110 and 120
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
Bit map 0
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 10, 36, 40, 114, 118
- EXT-IND
This IE does not carry the complete BA
SYSTEM INFORMATION type 5bis message
E-GSM:
Information elements
Value/Remark
Extension of BCCH frequency list description
For cell A
- Format identifier
Range 256
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 988, 990, 1 003
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
range 128
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 1 005, 1 010, 1 015
- EXT-IND
This IE does not carry the complete BA
R-GSM or ER-GSM:
Information elements
Value/Remark
Extension of BCCH frequency list description
For cell A
- Format identifier
Range 256
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 962, 965, 968, 980, 990
- EXT-IND
This IE does not carry the complete BA
For cell B
- Format identifier
range 128
- BCCH Allocation Sequence
0
- BCCH Allocation ARFCN
Channels numbers 968, 970, 972, 1005, 1010
- EXT-IND
This IE does not carry the complete BA
SYSTEM INFORMATION type 6 message
Information elements
Value/Remark
Cell identity
see below
LAI
see below
Cell options
see below
NCC permitted
see below
Common contents of information elements in SYSTEM INFORMATION TYPE 1 to 6 messages
(CBCH) Channel Description
Not present
(CBCH) Mobile Allocation
Not present
Cell Identity
- Cell Identity Value
0001H for cell A, 0002H for cell B
Cell Options
- Power Control Indicator
Power Control Indicator is not set
- DTX Indicator
MS shall not use DTX
- Radio-Link-Time-out
8 SACCH blocks
Cell Selection Parameters
- Cell-Reselect-Hysteresis
12 dB
- MX-TXPWR-MAX-CCH
Minimum level
- ACS
No addition cell parameters are present in SYSTEM INFORMATION messages 7 and 8.
- NECI
New establishment causes not supported
- RXLEV-ACCESS-MIN
Minimum level
Control Channel Description
- Attach-Detach allowed
No Attach/Detach
- BS-AG-BLKS-RES
0 blocks reserved for access grant
- CCCH-CONF
1 basic physical channel used for CCCH, combined with SDCCHs
- BS-PA-MFRMS
5 multiframe periods for transmission of paging messages
- T3212 Time-out value
Infinite
L2 pseudo length
- System information 1
21
- System information 2
22
- System information 2bis
21
- System information 3
18
- System information 4
12
Location Area Identification
- Mobile Country Code
001 decimal
- Mobile Network Code
01 decimal
- Location Area Code
0001H
Message Type
- System information 1
00011001
- System information 2
00011010
- System information 2bis
00000010
- System information 3
00011011
- System information 4
00011100
- System information 5
00011101
- System information 5bis
00000101
- System information 6
00011110
NCC Permitted
0000 0010
RACH Control Parameters
- Max Retrans
Max 1 retrans
- Tx-integer
5 slots used
- Cell Barred for Access
Cell is not barred
- Call Reestablishment Allowed
Not allowed
- Access Control Class
Access is not barred
- Emergency Call allowed
Yes
SI 1 rest octets
Not used (all bits are set to spare)
SI 2 rest octets
Not used (all bits are set to spare)
SI 3 rest octets
Not used (all bits are set to spare)
SI 4 rest octets
Not used (all bits are set to spare)
Default settings for cell A:
Downlink input level
63 dBmicroVolt emf
Uplink output power
minimum supported by the MS's power class
Propagation profile
static
BCCH/CCCH carrier number
20
Default settings for cell B:
Downlink input level
53 dBmicroVolt emf
Uplink output power
minimum supported by the MS's power class
Propagation profile
static
BCCH/CCCH carrier number
10
Default message contents for other messages
For subclauses 26.10.1 to 26.10.2.5
same as in 26.6.14
For subclause 26.10.3
same as in 26.9.7
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11 Multiband signalling
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.1 General considerations
|
This subclause applies only to Multiband mobile stations, as defined in 3GPP TS 02.06 subclause 3.2.1.
Conformance requirements of clause 26 fully apply to any Multiband MS in the whole supported band(s) of operation of the mobile station.
A Multiband mobile station has the functionality to perform handover, channel assignment, cell selection and re-selection between all its bands of operation within a PLMN.
A Multiband mobile station shall meet all requirements specified for each individual band. In addition it shall meet the extra functional requirements for multiband mobile stations.
The purpose of this subclause is to test these extra functional requirements for a multiband mobile station.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2 Multiband signalling / RR
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.1 Multiband signalling / RR / Immediate assignment procedure
|
To inform the multiband network of the MSs additional frequency and power capability, the multiband MS has to send a CLASSMARK CHANGE as soon as possible in a connection establishment.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.1.1 Conformance requirement
|
Following a PAGING REQUEST message, the MS shall correctly set up an RR connection on a supported channel described in the IMMEDIATE ASSIGNMENT message. On the MS side, the procedure is terminated when the establishment of the main signalling link is confirmed. When the ES bit is set to 1 in the Classmark 1 or the Classmark 2 information element and the Early Sending Classmark Control bit is set to "high" in SI3 Rest Octets, then the MS shall send, on the first occasion, the CLASSMARK CHANGE message.
During a contention resolution procedure, if the last timeslot of the block containing a L2 UA frame occurs at time T, then the MS shall be ready to transmit the CLASSMARK CHANGE before T + 40 ms.
Reference(s)
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1.2 and 3.3.1.1.4.
3GPP TS 04.13 subclause 5.2.11.
3GPP TS 05.10 subclause 6.10.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.1.2 Test purpose
|
To verify that the MS can correctly set up a dedicated control channel and that a multi band MS is able to perform early sending of CLASSMARK CHANGE.
To verify the performance requirement on early sending of the CLASSMARK CHANGE message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.1.3 Method of test
|
Initial Conditions
System Simulator:
For 450/900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 263.
For 480/900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 310.
For 450/1 800 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 263.
For 480/1 800 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 310.
For 900/1 800 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 20.
For 710/1 900 MS, 750/1 900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 457.
For 850/1 900 MS:
1 cell.
CCCH-CONF is set to "1 basic physical channel used for CCCH not combined with SDCCHs".
BCCH carrier number 147.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated.
Specific PICS statements:
- GSM 450 Band (TSPC_Type_GSM_450_Band)
- Standard GSM Band (P-GSM) (TSPC_Type_GSM_P_Band)
- Extended GSM Band (E-GSM) (TSPC_Type_GSM_E_Band)
- GSM 480 Band (TSPC_Type_GSM_480_Band)
- DCS 1800 band (TSPC_Type_DCS_Band)
- GSM 750 band (TSPC_Type_GSM_750_Band)
- GSM 710 band (TSPC_Type_GSM_710_Band)
PIXIT statements:
-
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The test is performed twice, first time in the lower band (BCCH carrier number 20, 263, 310, 457 or 147) and second time in the upper band (BCCH carrier number 20 or 590).
The System Simulator pages the MS and after the MS has responded with a CHANNEL REQUEST message the SS assigns an SDCCH. The MS shall go to the correct channel and send a PAGING RESPONSE message followed by a CLASSMARK CHANGE message. Then the SS initiates RR-release by sending a CHANNEL RELEASE message.
Before the procedure is repeated, the SS is reconfigured to transmit BCCH carrier in the upper band of operation (ARFCN 20 or 590).
Maximum Duration of Test
6 seconds per value of the execution timer and 1 min for reconfiguring the SS.
Expected Sequence
This sequence is performed for execution counter k = 1 to 2.
Step
Direction
Message
Comments
1
SS -> MS
PAGING REQUEST TYPE 1
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
Channel Type: SDCCH/8
4
MS -> SS
SABM (PAGING RESPONSE)
Shall be sent on the correct channel
5
SS -> MS
UA (PAGING RESPONSE)
6
MS -> SS
CLASSMARK CHANGE
Shall be ready to transmit (see 3GPP TS 05.10 subclause 06.10) within 40 ms after the completion of step 4. Shall indicate the MS frequency and power capabilities
Note: In this case 'ready to transmit' shall result in the actual transmission of the Classmark Change 51 frames later (51 * 4.62ms = 235.62 ms). Therefore receipt of the Classmark Change within 250ms of step 4 is required.
7
SS -> MS
CHANNEL RELEASE
Specific Message Contents
For 450/900 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 263
k=2; ARFCN 20
Mobile Allocation
empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 450 power capability
k=2; GSM 900 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 450 power capability
k=2; GSM 900 power capability
Additional MS Classmark information
- Band 1 (P-GSM) supported
According to PICS statement
- Band 2 (E-GSM) supported
According to PICS statement
- R-Band (R-GSM) supported
According to PICS statement
- - ER-Band (ER-GSM) supported
According to PICS statement
- GSM 400 Band (GSM 450) supported
According to PICS statement
- GSM400 Associated radio capability
Corresponding to GSM 400 band
- Associated radio capability 1
Corresponding to GSM 900 band
- R-Band Associated radio capability
Corresponding to R-GSM 900 band
For 480/900 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 310
k=2; ARFCN 20
Mobile Allocation
empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 480 power capability
k=2; GSM 900 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 480 power capability
k=2; GSM 900 power capability
Additional MS Classmark information
- Band 1 (P-GSM) supported
According to PICS statement
- Band 2 (E-GSM) supported
According to PICS statement
- R-Band (R-GSM) supported
According to PICS statement
- ER-Band (ER-GSM) supported
According to PICS statement
- GSM 400 Band (GSM 480) supported
According to PICS statement
- GSM 400 Associated radio capability
Corresponding to GSM 480 band
- Associated radio capability 1
Corresponding to GSM 900 band
- R-Band Associated radio capability
Corresponding to R-GSM 900 band
For 450/1 800 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 263
k=2; ARFCN 590
Mobile Allocation
empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 450 power capability
k=2; DCS 1 800 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 450 power capability
k=2; DCS 1 800 power capability
Additional MS Classmark information
- Band 3 (DCS 1 800) supported
According to PICS statement
- GSM 400 Band (GSM 450) supported
According to PICS statement
- GSM 400 Associated radio capability
Corresponding to GSM 450 band
- Associated radio capability 2
Corresponding to DCS 1 800 band
For 480/1 800 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 310
k=2; ARFCN 590
Mobile Allocation
empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 480 power capability
k=2; DCS 1 800 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 480 power capability
k=2; DCS 1 800 power capability
Additional MS Classmark information
- Band 3 (DCS 1 800) supported
According to PICS statement
- GSM 400 Band (GSM 480) supported
According to PICS statement
- GSM 400 Associated radio capability
Corresponding to GSM 480 band
- Associated radio capability 2
Corresponding to DCS 1 800 band
For 900/1 800 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 20
k=2; ARFCN 590
Mobile Allocation
empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 900 power capability
k=2; DCS 1 800 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 900 power capability
k=2; DCS 1 800 power capability
Additional MS Classmark information
- Band 1 (P-GSM) supported
According to PICS statement
- Band 2 (E-GSM) supported
According to PICS statement
- Band 3 (DCS 1 800) supported
According to PICS statement
- R-Band (R-GSM) supported
According to PICS statement
- ER-Band (ER-GSM) supported
According to PICS statement
- Associated radio capability 1
Corresponding to GSM 900 band
- Associated radio capability 2
Corresponding to DCS 1 800 band
- R-Band Associated radio capability
Corresponding to R-GSM 900 band
For 710/1 900 MS, 750/1 900 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 457
k=2; ARFCN 590
Mobile Allocation
Empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 700 power capability
k=2; PCS 1 900 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
Corresponding to the frequency band in use
k=1; GSM 700 power capability
k=2; GSM 1900 power capability
Additional MS Classmark information
- GSM 700 Associated radio capability
Corresponding to GSM 700 band
- PCS 1 900 Associated radio capability
Corresponding to PCS 1 900 band
For 850/1 900 MS:
IMMEDIATE ASSIGNMENT
As default except:
Information element
Value/remark
Channel description
- Channel Type
SDCCH/8
- Timeslot number
Arbitrary but not zero
- Training sequence code
Arbitrary
- Hopping channel
Single RF
- Channel selector
k=1; ARFCN 147
k=2; ARFCN 590
Mobile Allocation
Empty
PAGING RESPONSE
Information element
Value/remark
Protocol Discriminator
RR management
Ciphering Key Sequence number
- Key Sequence
Key sequence number previously allocated to MS, or "111" if no key is available
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
corresponding to the frequency band in use
k=1; GSM 850 power capability
k=2; DCS 1 900 power capability
Mobile Identity
- odd/even
Even
- Type of identity
TMSI
- Identity digits
TMSI previously allocated to MS
CLASSMARK CHANGE
Information element
Value/remark
Protocol Discriminator
RR management
Mobile station Classmark 2
- ES IND
Shall indicate early autonomous sending of CLASSMARK CHANGE
- RF power capability
Corresponding to the frequency band in use
k=1; GSM 850 power capability
k=2; DCS 1 900 power capability
Additional MS Classmark information
- GSM 850 Associated radio capability
Corresponding to GSM 850 band
- PCS 1 900 Associated radio capability
Corresponding to PCS 1 900 band
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2 Multiband signalling / RR / Handover
|
This subclause applies to any multiband mobile stations.
The purpose of this extra section is to test the handover where the target cell uses frequencies outside the frequency band of the serving cell.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.1 Multiband signalling / RR / Handover / successful / active call / non-synchronized
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.1.1 Conformance requirements
|
The MS shall correctly apply the handover procedure in the non-synchronized case when a call is in progress and when handover is performed from a TCH/F without frequency hopping in one band towards a TCH/F without frequency hopping in another band.
When the MS releases a TCH or SDCCH and returns to idle mode, it shall, as quickly as possible, camp on the BCCH carrier of the cell whose channel has just been released, ie the BCCH carrier indicated in the HANDOVER COMMAND.
A multi band mobile station shall not consider a HANDOVER COMMAND as invalid because it indicates target channel frequencies that are all in a different frequency band to that of the ARFCN in the Cell Description IE.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.4 and 9.1.15.
3GPP TS 04.13 subclause 5.2.6.2.
3GPP TS 05.08 subclause 6.7.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.1.2 Test purpose
|
To test that when the MS is ordered to make a non-synchronized handover it continuously sends access bursts on the main DCCH (and optionally on the SACCH) until it receives a PHYSICAL INFORMATION message from the SS. To test that the MS correctly handles the Timing Advance IE in the PHYSICAL INFORMATION message. To test that the MS activates the new channel correctly and transmits the HANDOVER COMPLETE message without undue delay. To test that upon release of the TCH, the mobile camps on the BCCH carrier of the cell indicated in the HANDOVER COMMAND.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.1.3 Method of test
|
Initial Conditions
For execution counter M =1, 2
System Simulator:
For 450/900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263
Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
Cell B has:
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 480/900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310
Cell Allocation = (306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338)
Cell B has:
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 450/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263
Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
Cell B has:
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 480/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310
Cell Allocation = (306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338)
Cell B has:
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 900/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
Cell B has:
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 710/1 900 MS, 750/1 900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 457
Cell Allocation = (447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508)
Cell B has:
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 803, 804, 806)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
For 850/1 900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 147
Cell Allocation = (137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241)
Cell B has:
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 803, 804, 806)
The frame numbers of cells A and B shall be different by 100.
The timebase of cells A and B shall be such that the edges of their timeslots are not coincident at the antenna connector.
Mobile Station:
The MS is in the active state (U10) of a call on cell A. (for execution counter M = 1) and on cell B (for execution counter M=2).
For execution counter M = 3
System Simulator:
For 450/900 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263
Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 480/900 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310
Cell Allocation = (306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 450/1 800 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263
Cell Allocation = (259, 261, 263, 265, 267, 269, 271, 273, 275, 277, 279, 281, 283, 285, 287, 289, 291)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 480/1 800 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310
Cell Allocation = (306, 308, 310, 312, 314, 316, 318, 320, 322, 324, 326, 328, 330, 332, 334, 336, 338)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 900/1 800 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 20
Cell Allocation = (10, 17, 20, 26, 34, 42, 45, 46, 52, 59, 66, 73, 74, 75, 76, 108, 114)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 829, 832, 844)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 710/1 900 MS, 750/1 900 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 457
Cell Allocation = (447, 454, 457, 463, 471, 479, 482 ,483 ,489, 496, 498, 500, 501, 502, 503, 506, 508)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 803, 804, 806)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
For 850/1 900 MS: 2 cells, A and B with different LAI, default parameters except:
Cell A has:
BCCH ARFCN = 147
Cell Allocation = (137, 144, 147, 153, 161, 169, 172, 173, 179, 186, 193, 200, 201, 202, 203, 235, 241)
Cell B has:
LAI = 0003 H
BCCH ARFCN = 764
Cell Allocation = (739, 743, 746, 749, 756, 758, 761, 764, 771, 779, 782, 791, 798, 803, 804, 806)
The frame numbers of cells A and B shall be the same. The timebase of cells A and B shall be such that the edges of their timeslots are coincident at the antenna connector. ie cells A and B shall be fully synchronised.
Mobile Station:
The MS is succesfully registered in the LA of cell A and the MS is in the active state (U10) of a call on cell A.
Specific PICS statements:
- GSM 450 Band (TSPC_Type_GSM_450_Band)
- Standard GSM Band (P-GSM) (TSPC_Type_GSM_P_Band)
- Extended GSM Band (E-GSM) (TSPC_Type_GSM_E_Band)
- GSM 480 Band (TSPC_Type_GSM_480_Band)
- DCS 1800 band (TSPC_Type_DCS_Band)
- GSM 750 band (TSPC_Type_GSM_750_Band)
- GSM 710 band (TSPC_Type_GSM_710_Band)
PIXIT statements:
-
Foreseen Final State of the MS
For execution counter M = 1:
The active state (U10) of a call on cell B.
For execution counter M = 2:
The active state (U10) of a call on cell A.
For execution counter M = 3:
The MM idle state on cell A.
Test Procedure
The MS is in the active state (U10) of a call on cell A. The SS sends a HANDOVER COMMAND on the main DCCH. The MS shall begin to send access bursts on the new DCCH (and optionally on the SACCH) of the target cell. The SS observes the access bursts and after receiving n (n being randomly drawn between values according to table 26.6‑2 of subclause 26.6.5) access bursts, the SS sends one PHYSICAL INFORMATION message with a Timing Advance as specified in table 26.6‑1 of subclause 26.6.5. The MS shall activate the channel in sending and receiving mode. The MS shall establish a signalling link. The MS shall be ready to transmit a HANDOVER COMPLETE message, before "x" ms after the end of the PHYSICAL INFORMATION message, but not before a UA frame has been sent by the SS.
The term "ready to transmit" is defined in 3GPP TS 04.13. The value of "x" depends upon the target channel and is specified in the specific message contents section.
For execution counter M = 3, the call is then released and then the SS sends a CHANNEL RELEASE message. It is then checked for 2 minutes that the MS does not access Cell B.
Note: the CRH parameter is set to 12 dB. After the Channel release, the MS is required to go to the BCCH carrier of cell A. Then C1 on cell A is greater than_that on cell B Hence the MS shall not location update on cell B. The absence of additional cell (re)selection parameters means that C2 = C1.
Maximum Duration of Test
5 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
This sequence is performed for an execution counter M = 1, 2, 3 for an MS which supports TCH/F.
Steps after step 7 are only performed for execution counter M = 3.
Step
Direction
Message
Comments
0
MS -> SS
The MS and SS are in the active state of a call on the channel described below.
1
SS -> MS
HANDOVER COMMAND
See Specific message contents
2
MS -> SS
HANDOVER ACCESS
Repeated on every burst of the uplink main DCCH (and optionally on the SACCH) until reception of PHYSICAL INFORMATION. Handover Reference as included in the HANDOVER COMMAND.
3
SS -> MS
PHYSICAL INFORMATION
Sent after reception of n HANDOVER ACCESS messages. See specific message contents.
4
MS -> SS
SABM
Sent without information field
5
SS -> MS
UA
6
MS -> SS
HANDOVER COMPLETE
The message shall be ready to be transmitted before "x" ms after the completion of step 3.
7
MS -> SS
The MS and SS are in the active state of a call on the channel described below.
steps 8-10 are only performed for execution counter M = 3.
8
SS -> MS
RELEASE COMPLETE
9
SS -> MS
CHANNEL RELEASE
10
SS
The SS checks that for a period of 2 minutes, the MS does not access cell B.
Specific Message Contents For Mobiles Supporting Speech
In case of 450/900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Bit map 0
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 3, 20, 29, 62, 84, 89, 99 and 119
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
263
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (259, 261, 263, 265, 277, 279, 281, 283, 285, 287, 289, 291)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
263
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 480/900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Bit map 0
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 3, 20, 29, 62, 84, 89, 99 and 119
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
310
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (306, 308, 310, 312, 324, 326, 328, 330, 332, 334, 336, 338)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
310
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 450/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
263
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (259, 261, 263, 265, 277, 279, 281, 283, 285, 287, 289, 291)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
263
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 480/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
310
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency List IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (306, 308, 310, 312, 324, 326, 328, 330, 332, 334, 336, 338)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
310
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 900/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency Channel Sequence IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency Channel Sequence after time
- Frequency Channel Sequence
Allocates the following 12 frequencies (10, 17, 20, 26, 59, 66, 73, 74, 75, 76,108, 114)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 710/1 900 MS, 750/1 900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 800 and 810
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
457
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency Channel Sequence IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (447, 454, 457, 463, 496, 498, 500, 501, 502, 503, 506, 508)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
457
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
In case of 850/1 900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 800 and 810
For M = 1:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
For M = 2:
Step 0: The MS and SS are using a full rate TCH in non-hopping mode on cell B.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
147
Channel Description
- Channel Type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not Zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
RF hopping channel.
- MAIO
Chosen arbitrarily from the set (0, 1 to N‑1), where N is the number of frequencies encoded in the Frequency Channel Sequence IE.
- HSN
Chosen arbitrarily from the set (1,2,..63)
Synchronization Indication IE is not included.
Channel Mode IE is not included.
Frequency List after time
- Frequency List
Allocates the following 12 frequencies (137, 144, 147, 153, 186, 193, 200, 201, 202, 203, 235, 241)
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents, except:
Timing advance
Arbitrarily selected but different to default value.
Step 6: x = 500.
Step 7: The MS and SS are using a full rate TCH in hopping mode on cell A.
For M = 3:
Step 0: The MS and SS are using a full rate TCH in hopping mode on cell A.
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
147
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily,but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronisation Indication
- Report Observed Time Difference
Shall not be included.
- Synchronisation Indication
'Non synchronised'.
- Normal Cell Indication
Ignore out of range timing advance.
PHYSICAL INFORMATION
Information Element
value/remarks
As default message contents.
Step 6: x = 500
Step 7: The MS and SS are using a full rate TCH in non hopping mode on cell B.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.2 Multiband signalling / RR / Handover / layer 1 failure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.2.1 Conformance requirements
|
During a handover from a channel in the lower band to a channel in the upper band, or the contrary, the MS shall correctly return to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.2.2 Test purpose
|
To check that the MS correctly returns to the old channel in the case of an handover failure caused by a layer 1 failure on the target cell, if the origin is in the lower band and the target is in the upper band or the contrary.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.11.2.2.2.3 Method of test
|
Initial Conditions
System Simulator:
For 450/900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263.
Cell B has:
BCCH ARFCN = 20.
For 480/900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310.
Cell B has:
BCCH ARFCN = 20.
For 450/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 263.
Cell B has:
BCCH ARFCN = 764.
For 480/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 310.
Cell B has:
BCCH ARFCN = 764.
For 900/1 800 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 20.
Cell B has:
BCCH ARFCN = 764.
For 710/1 900 MS, 750/1 900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 457.
Cell B has:
BCCH ARFCN = 764.
For 850/1 900 MS: 2 cells, A and B with same LAI, default parameters except:
Cell A has:
BCCH ARFCN = 147.
Cell B has:
BCCH ARFCN = 764.
Mobile Station:
The MS is in the active state (U10) of a call on cell A. Used power level is the maximum supported by the MS in the band in use.
Specific PICS statements:
- GSM 450 Band (TSPC_Type_GSM_450_Band)
- Standard GSM Band (P-GSM) (TSPC_Type_GSM_P_Band)
- Extended GSM Band (E-GSM) (TSPC_Type_GSM_E_Band)
- GSM 480 Band (TSPC_Type_GSM_480_Band)
- DCS 1800 band (TSPC_Type_DCS_Band)
- GSM 750 band (TSPC_Type_GSM_750_Band)
- GSM 710 band (TSPC_Type_GSM_710_Band)
PIXIT statements:
-
Foreseen Final State of the MS
The active state (U10) of a mobile call on cell A. Used power level is the maximum supported by the MS in the band in use.
Test Procedure
The MS is in the active state (U10) of a call on cell A. The SS sends a HANDOVER COMMAND on the main DCCH. The MS shall begin to send access bursts on the new DCCH (and optionally on the SACCH) to cell B. With the exception of normal BCCH signalling, the SS does not transmit anything on cell B (thus causing a time-out of T3124). The MS shall re-establish the old link on cell A and send a HANDOVER FAILURE within 3 seconds from the transmission of HANDOVER COMMAND, using the old Power Control Level.
Maximum Duration of Test
5 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
Step
Direction
Message
Comments
0
SS
-
The SS records the old Power Control Level in the layer 1 header of the last SACCH message sent by the MS before step 1.
1
SS -> MS
HANDOVER COMMAND
Channel description: non-hopping, full rate. Synchronisation Indication: non synchronised.
2
MS -> SS
HANDOVER ACCESS
Several messages are sent, all with correct Handover References.
3
MS -> SS
HANDOVER FAILURE
Sent on old channel, RR cause value ="Abnormal release, unspecified", "Abnormal release, channel unacceptable", "Abnormal release, timer expired", "Abnormal release, no activity on the radio path" or "Protocol error unspecified".Shall be sent within 3 seconds from the transmission of HANDOVER COMMAND.
4
SS
-
The SS checks that the PowerControl Level reported in the layer 1 header of the SACCH message that is sent in the first SACCH multiframe following the SABM is the same as in step 0.
Specific Message Contents
For 450/900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Bit map 0
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 3, 20, 29, 62, 84, 89, 99 and 119
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 480/900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Bit map 0
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 3, 20, 29, 62, 84, 89, 99 and 119
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
20
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 450/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 480/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 900/1 800 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 810 and 870
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 710/1 900 MS, 750/1 900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 800 and 810
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
For 850/1 900 MS:
SYSTEM INFORMATION TYPE 5ter
Information Element
Value/remark
Neighbour Cells Description 2
Multiband reporting
0
For Cell A
- Format notation
Range 512
- BA_IND
0
- BCCH Allocation ARFCN
ARFCN 520, 590, 600, 700, 764, 780, 800 and 810
HANDOVER COMMAND
Information Element
value/remarks
As default message contents, except:
Cell Description
- Network Colour Code
1
- Base Station Colour Code
5
- BCCH Carrier Number
764
Channel description
- Channel type
TCH/F + ACCHs
- Timeslot number
Chosen arbitrarily, but not zero
- Training Sequence Code
Chosen arbitrarily
- Hopping
Single RF.
- ARFCN
Chosen arbitrarily from Cell Allocation for cell B.
Synchronization Indication
- Report Observed Time Difference
Shall not be included.
- Synchronization Indication
"Non synchronized".
- Normal Cell Indication
Ignore out of range timing advance.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.