hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2 Outgoing call / U0.1 MM connection pending
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.1 Outgoing call / U0.1 MM connection pending / CM service rejected
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.1.1 Definition
|
A request for MM connection is rejected by the SS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.1.2 Conformance requirement
|
Upon receiving indication of an MM-connection establishment being rejected, CC entity should inform upper layer of this rejection.
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 4.5.1.1, 3GPP TS 04.07 / 3GPP TS 24.007, subclause 6.2.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.1.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U0.1, "MM-connection pending", upon the MS receiving a CM SERVICE REJECT message, returns to CC state U0, "Null".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.1.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U0.1 by using table 26.8.1.2/1.
Foreseen final state of the MS
U0, null.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. When the SS receives CM SERVICE REQUEST, the contents of it shall be checked. The SS rejects it by CM SERVICE REJECT. Then the SS will check the state of the MS by using STATUS ENQUIRY with all the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
CM SERVICE REJECT
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
RELEASE COMPLETE
cause shall be 81# (invalid TI value)
4
SS
repeat steps 2‑3 to cover all the transaction identifiers from 000 ...110
5
SS -> MS
CHANNEL RELEASE
6
MS
the MS shall release the main signalling link (DISC/UA)
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.2 Outgoing call / U0.1 MM connection pending / CM service accepted
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.2.1 Definition
|
A CM request is accepted for the MM-connection by the SS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.2.2 Conformance requirement
|
A CC entity of the MS in CC-state U0.1, "MM-connection pending", upon the MS receiving a CM SERVICE ACCEPT message, shall send a SETUP message specifying the Called party BCD number that was entered into the MS and then enter CC state U1, "Call initiated".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 4.5.1.1 and 5.2.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.2.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U0.1, "MM-connection pending", upon the MS receiving a CM SERVICE ACCEPT message, sends a SETUP message specifying the Called party BCD number that was entered into the MS and then enters CC state U1, "Call initiated".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.2.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U0.1 by using table 26.8.1.2/1.
Foreseen final state of the MS
U1, call initiated.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. When the MS is requesting a MM-connection, the SS will indicate acceptance by sending a CM SERVICE ACCEPT message. The MS shall respond with SETUP. Then the SS will check the state of the call control entity by STATUS ENQUIRY with the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
CM SERVICE ACCEPT
2
MS -> SS
SETUP
with called party BCD number.
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause shall be 30# (response to enq.) and state U1 call initiated.
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.3 Outgoing call / U0.1 MM connection pending / lower layer failure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.3.1 Definition
|
The call control entity of the MS being in the state, U0.1, a lower layer failure is accomplished at the MS and consequently, communication at layer 3 level with the peer entity is terminated. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.3.2 Conformance requirement
|
1) Upon a lower layer failure the MS releases the MM connection in progress and returns to idle mode. In that state no call exists and the CC entities relating to the seven mobile originating transaction identifiers are in state U0, "Null".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 4.5.1.2, 5.2.1.1, 5.5.3.2 and 8.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.3.3 Test purpose
|
To verify that after the MS with a CC entity in state U0.1, "MM-connection pending", has detected a lower layer failure and has returned to idle mode, the CC entities relating to the seven mobile originating transaction identifiers are in state U0, "Null".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.2.3.4 Method of test
|
Specific PICS statements
- Support of UTRAN Radio Access Technology (TSPC_Type_UTRAN)
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U0.1 by using table 26.8.1.2/1.
Foreseen final state of the MS
U0, null.
Maximum duration of test
1 min.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. When the MS has sent a CM SERVICE REQUEST message, the SS generates a lower layer failure at the MS. The SS waits long enough to enable the MS to return to idle state listening to paging, and then pages MS to create RR-connection. Finally, the SS will check the state of the MS by using STATUS ENQUIRY with the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS
SS generates lower layer failure.
2
SS
If PICS statement “Support of UTRAN Radio Access Technology” is ‘NO’, then the SS waits 20 s for the MS to return to listening to paging.
If PICS statement “Support of UTRAN Radio Access Technology” is ‘YES’, then the SS waits 50 s for the MS to return to listening to paging.
3
SS -> MS
PAGING REQUEST
4
MS -> SS
CHANNEL REQUEST
5
SS -> MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
PAGING RESPONSE
7
SS -> MS
STATUS ENQUIRY
8
MS -> SS
RELEASE COMPLETE
cause shall be 81# (invalid TI value).
9
SS
repeat steps 7‑8 to cover all the transaction identifiers from 000 ...110.
10
SS -> MS
CHANNEL RELEASE
the main signalling link shall be released by the MS (L2: DISC/UA).
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3 Outgoing call / U1 call initiated
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.1 Outgoing call / U1 call initiated / receiving CALL PROCEEDING
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.1.1 Definition
|
The call control entity of the MS being in the state, U1, a CALL PROCEEDING message is sent by the SS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.1.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a CALL PROCEEDING message, shall enter CC state U3, "Mobile originating call proceeding".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.1, 5.2.1.2 and 5.2.1.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.1.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a CALL PROCEEDING message, enters CC state U3, "Mobile originating call proceeding".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.1.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/2.
Foreseen final state of the MS
U3, Mobile originating call proceeding.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. The SS sends a CALL PROCEEDING message to the MS. The SS checks by using the status enquiry procedure that the CC entity has entered the state U3.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
CALL PROCEEDING
tone generation not mandatory
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
cause 30#, state U3
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.2 Outgoing call / U1 call initiated / rejecting with RELEASE COMPLETE
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.2.1 Definition
|
The call control entity of the MS being in the state, U1, the call is rejected by a RELEASE COMPLETE message sent by the SS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.2.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a RELEASE COMPLETE message with valid cause value, shall enter CC state U0, "Null".
2) On returning to idle mode, the CC entities relating to the seven mobile originating transaction identifiers shall be in state U0, "Null".
3) On releasing the MM-connection, the MS shall wait for MM layer release initiated by the network.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.4.2 and 5.4.4.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.5.3.2.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.4.4.3 and 4.5.3,
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.13.1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.2.3 Test purpose
|
1) To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a RELEASE COMPLETE message with valid cause value, enters CC state U0, "Null".
2) To verify that in returning to idle mode, the CC entities relating to the seven mobile originating transaction identifiers are in state U0, "Null".
3) To verify that in releasing the MM-connection, the MS shall wait for MM layer release initiated by SS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.2.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/2.
Foreseen final state of the MS
U0, null.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. The SS sends a RELEASE COMPLETE message to the MS. The SS checks by using the status enquiry procedure that the CC entity has entered the state U0 with all the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
RELEASE COMPLETE
See specific message content below.
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
RELEASE COMPLETE
cause 81# (invalid TI value)
4
SS
repeat steps 2‑3 to cover all the transaction identifiers from 000...110
5
SS -> MS
CHANNEL RELEASE
the main signalling link shall be released by the MS (L2: DISC/UA).
Specific message contents:
RELEASE COMPLETE
1) With a valid cause value among:
related to numbering,
#1 unallocated number
#3 no route to destination
#22 number changed
#28 invalid number format
related to bearer capabilities,
#8 operator determined barring
#57 bearer capability not authorized
#58 bearer capability not presently available
#63 service or option not available
#65 bearer service not implemented
#34 no circuit/channel available (call queuing).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.3 Outgoing call / U1 call initiated / T303 expiry
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.3.1 Definition
|
The call control entity of the MS being in the state, U1, if no response is then received from the SS, timer T303 expires at the MS side. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.3.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon expiry of T303 shall send a DISCONNECT message to its peer entity and enter state U11, "Disconnect request".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.1 and 5.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.3.3 Test purpose
|
1) To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon expiry of T303 (accuracy ±20 % between reception of CM SERVICE REQUEST and DISCONNECT by SS) sends a DISCONNECT message to its peer entity and enters state U11, "Disconnect request".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.3.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/2.
Foreseen final state of the MS
U11, disconnect request.
Maximum duration of test
1 minute.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. When T303 expires at the MS, the MS shall send DISCONNECT. The SS checks by using the status enquiry procedure that the CC entity has entered the state U11, disconnect request.
Expected sequence
Step
Direction
Message
Comments
1
SS
SS waits for T303 expiry.
2
MS -> SS
DISCONNECT
Shall be transmitted between 24 s and 36 s after the CM SERVICE REQUEST.
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, status U11
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.4 Outgoing call / U1 call initiated / lower layer failure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.4.1 Definition
|
The call control entity of the MS being in the state, U1, a lower layer failure is accomplished at the MS and consequently, communication at layer 3 level with the peer entity is terminated. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.4.2 Conformance requirement
|
Upon a lower layer failure MM informs the relevant CM entities that the MM connection has been interrupted. As call re-establishment is not allowed, the CC entity must perform a local release. The MS returns to idle mode. In that state no call exists, and the CC entities relating to the seven mobile originating transaction identifiers are in state U0, "Null".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 4.5.2.3, 5.2.1.1 and 5.5.3.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.4.3 Test purpose
|
To verify that after the MS with a CC entity in state U1 "Call initiated", has detected a lower layer failure and has returned to idle mode, the CC entities relating to the seven mobile originating transaction identifiers are in state U0, "Null".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.4.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/4.
Foreseen final state of the MS
U0, null.
Maximum duration of test
1 min.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The MS is brought to the state U1. The SS generates a lower layer failure at the MS. The SS waits long enough to enable the MS to return to idle state listening to paging, and then pages MS to create RR-connection. Finally, the SS will check the state of the MS by using STATUS ENQUIRY with the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS
SS generates lower layer failure.
2
SS
SS waits 20 s for the MS to return to listening to paging.
3
SS -> MS
PAGING REQUEST
4
MS -> SS
CHANNEL REQUEST
5
SS -> MS
IMMEDIATE ASSIGNMENT
6
MS -> SS
PAGING RESPONSE
7
SS -> MS
STATUS ENQUIRY
8
MS -> SS
RELEASE COMPLETE
cause 81# (invalid TI value).
9
SS
repeat steps 7‑8 to cover all the transaction identifiers from 000...110.
10
SS -> MS
CHANNEL RELEASE
11
MS
the MS shall release the main signalling link (DISC/UA).
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.5 Outgoing call / U1 call initiated / receiving ALERTING
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.5.1 Definition
|
The call control entity of the MS being in the state, U1, an ALERTING message is sent to the MS as a indication that a call is being alerted at a called end. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.5.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon receipt of an ALERTING message, shall enter CC state U4, "Call delivered".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.5.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon receipt of an ALERTING message, enters CC state U4, "Call delivered".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.5.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/4.
Foreseen final state of the MS
U4, call delivered.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. The SS sends an ALERTING message to the MS. The SS checks by using the status enquiry procedure that the CC entity has entered the state U4, call delivered.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
ALERTING
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
cause 30#, state U4
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.6 Outgoing call / U1 call initiated / entering state U10
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.6.1 Definition
|
The call control entity of the MS being in the state, U1, a CONNECT message is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.6.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a CONNECT message, shall send a CONNECT ACKNOWLEDGE message to its peer entity and enter CC state U10, "Active".
References
3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.1.1 and 5.2.1.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.6.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a CONNECT message, sends a CONNECT ACKNOWLEDGE message to its peer entity and enters CC state U10, "Active".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.6.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/4.
Foreseen final state of the MS
U10, call active.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. The SS sends a CONNECT message to the MS. The MS shall respond by sending a CONNECT ACKNOWLEDGE message. The SS checks by using the status enquiry procedure that the CC entity has entered the state U10, active.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
CONNECT
2
MS -> SS
CONNECT ACKNOWLEDGE
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U10
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.7 Outgoing call / U1 call initiated / unknown message received
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.7.1 Definition
|
The call control entity of the MS being in the state, U1, an unknown message is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.7.2 Conformance requirement
|
1) A CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a message with message type not defined for the protocol discriminator from its peer entity shall return a STATUS message.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 8.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.7.3 Test purpose
|
To verify that a CC entity of the MS in CC-state U1, "Call initiated", upon receipt of a message with message type not defined for the protocol discriminator unknown message from its peer entity returns a STATUS message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.3.7.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U1 by using table 26.8.1.2/1.
Foreseen final state of the MS
U1, call initiated.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U1. The SS sends a message with message type not defined for the protocol discriminator to the MS. The MS shall respond with a STATUS message, and finally the SS checks by using the status enquiry procedure that the state of the CC entity has remained unchanged.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
unknown message
message type not defined for PD
2
MS -> SS
STATUS
cause 97#, state U1
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U1
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4 Outgoing call / U3 MS originating call proceeding
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.1 Outgoing call / U3 MS originating call proceeding / ALERTING received
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.1.1 Definition
|
The call control entity of the MS being in the state, U3, an ALERTING message is sent to the MS as a indication that a call is being alerted at a called end. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.1.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a ALERTING message shall enter CC-state U4, "Call Delivered".
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.1.3 Test purpose
|
To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a ALERTING message enters CC-state U4, "Call Delivered".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.1.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U4, call delivered.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends an ALERTING message to the MS. The SS checks by using the status enquiry procedure that the CC entity has entered the state U4, call delivered.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
ALERTING
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
cause 30#, state U4
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.2 Outgoing call / U3 MS originating call proceeding / CONNECT received
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.2.1 Definition
|
The call control entity of the MS being in the state, U3, a CONNECT message is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.2.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a CONNECT message shall return a "CONNECT ACKNOWLEDGE" message to its peer entity and enter the CC state U10, "Active".
2) The MS shall then stop any locally generated indication.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.6.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.2.3 Test purpose
|
1) To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a CONNECT message returns a "CONNECT ACKNOWLEDGE" message to its peer entity and enters the CC state U10, "Active".
2) To verify that the MS stops locally generated indication, if any.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.2.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U10, active.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a CONNECT message to the MS. The MS shall respond by sending a CONNECT ACKNOWLEDGE message. The SS checks by using the status enquiry procedure that the CC entity has entered the state U10, active.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
CONNECT
the MS shall stop tone generation, if any
2
MS -> SS
CONNECT ACKNOWLEDGE
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U10
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.3 Outgoing call / U3 MS originating call proceeding / PROGRESS received without in band information
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.3.1 Definition
|
The call control entity of the MS being in the state, U3, a PROGRESS message is received by the MS. The PROGRESS message does not contain indication of in-band information availability. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.3.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a PROGRESS message with valid Progress Indicator values shall stay in CC-state U3.
2) After receipt of the PROGRESS message timer T310 shall be stopped.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.4.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 11.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.3.3 Test purpose
|
1) To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a PROGRESS message with valid Progress Indicator values stays in CC-state U3.
2) To verify that after receipt of the PROGRESS message timer T310 is stopped.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.3.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U3, mobile originating call proceeding.
Maximum duration of test
1 min.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a PROGRESS message not containing indication of in-band information availability to the MS. The SS checks that the MS has stopped T310, i.e. at T310 time-out no DISCONNECT message is sent by the MS. Then the SS checks by using the status enquiry procedure that the state of the CC entity has remained unchanged.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
PROGRESS
(note)
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
cause 30#, state U3
4
SS
SS waits at least 45 s and checks no DISCONNECT is sent by the MS
5
SS -> MS
STATUS ENQUIRY
6
MS -> SS
STATUS
cause 30#, state U3
NOTE: Tested with a valid Progress Indicator value among:
#4 call has returned to PLMN/ISDN;
#32 call is end-to-end PLMN/ISDN; or
any value in the set #(21‑127).
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.4 Outgoing call / U3 MS originating call proceeding / PROGRESS with in band information
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.4.1 Definition
|
The call control entity of the MS being in the state, U3, a PROGRESS message indicating availability of in band information is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.4.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a PROGRESS message indicating in-band announcement shall through-connect the traffic channel for speech, if TCH is in a speech mode. If TCH is not in speech mode, the MS shall not through-connect the TCH.
2) After receipt of the PROGRESS message, T310 shall be stopped.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3,
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.1.3, 5.2.1.4, 5.2.1.9, 5.5.1 and 11.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.4.3 Test purpose
|
1) To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a PROGRESS message indicating in-band announcement through-connects the traffic channel for speech, if TCH is in speech mode. If TCH is not in a speech mode, the MS does not through-connect the TCH.
2) To verify that after receipt of the PROGRESS message, T310 is stopped.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.4.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U3, mobile originating call proceeding.
Maximum duration of test
1 minute.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a PROGRESS message containing indication of in-band information availability to the MS. The SS checks that if channel mode is speech, the TCH shall be through connected. If channel mode is not speech, the TCH shall not be through connected. Also the SS checks that the MS has stopped T310, i.e. at T310 time-out no DISCONNECT message is sent by the MS. Then the SS checks by using the status enquiry procedure that the state of the CC entity has remained unchanged.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
PROGRESS
the MS shall stop all the CC timers (note), if channel mode is speech, the TCH shall be through connected. If channel mode is not speech, the TCH shall not be through connected.
2
SS -> MS
STATUS ENQUIRY
3
MS -> SS
STATUS
cause 30#, state U3
4
SS
SS waits at least 45 s and checks no DISCONNECT is sent by the MS.
5
SS -> MS
STATUS ENQUIRY
6
MS -> SS
STATUS
cause 30#, state U3
7
SS
If the channel mode is speech the SS will check that the user connection for speech is attached (both downlink and uplink).
Specific message contents:
NOTE: Tested with a valid Progress Indicator value among:
#1 call is not end to end PLMN/ISDN;
#2 destination address is non PLMN/ISDN;
#3 originating address is non PLMN/ISDN;
#8 in band information or appropriate pattern now available; or
any value in the set #(6‑20).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.5 Outgoing call / U3 MS originating call proceeding / DISCONNECT with in band tones
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.5.1 Definition
|
The call control entity of the MS being in the state, U3, a DISCONNECT message indicating availability of in band information is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.5.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a DISCONNECT with progress indicator #8, shall through-connect the speech channel to make in-band announcements available, if traffic channel is in speech mode. If TCH is not in speech mode, the MS shall send a RELEASE message.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1.4 and 5.4.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.5.3 Test purpose
|
To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a DISCONNECT with progress indicator #8 through-connects the speech channel to make in-band announcements available, if traffic channel is in speech mode. If TCH is not in speech mode, the MS sends a RELEASE message.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.5.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U12, disconnect indication if TCH is speech mode.
U19, release request if TCH is not speech mode.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a DISCONNECT message containing indication of in-band information availability to the MS. The SS checks that if channel mode is speech, the TCH shall be through connected and the MS enters state U12, disconnect indication. If channel mode is not speech, the TCH shall not be through connected and the MS shall enter state U19, release request.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
DISCONNECT
(note)
TCH in speech mode:
B2
SS
the SS will check that the audio path for in band tones is attached.
B3
SS -> MS
STATUS ENQUIRY
B4
MS -> SS
STATUS
cause 30#, state U12
TCH is not in speech mode:
C2
MS -> SS
RELEASE
C3
SS -> MS
STATUS ENQUIRY
C4
MS -> SS
STATUS
cause 30#, state U19
Specific message contents:
NOTE: the Progress Indicator value:
#8 in band information or appropriate pattern now available.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.6 Outgoing call / U3 MS originating call proceeding / DISCONNECT without in band tones
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.6.1 Definition
|
The call control entity of the MS being in the state, U3, a DISCONNECT message is received by the MS. The DISCONNECT message does not contain indication of in-band information availability. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.6.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a DISCONNECT without progress indicator shall return a RELEASE message and enter the CC-state U19, "Release Request"
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.4.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.6.3 Test purpose
|
To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a DISCONNECT without progress indicator returns a RELEASE message and enters the CC-state U19, "Release Request".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.6.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U19, release request.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a DISCONNECT message not containing indication of in-band information availability to the MS. The MS shall respond with a RELEASE message. The SS checks by using the status enquiry procedure that the CC entity of the MS has entered the state U19, release request.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
DISCONNECT
2
MS -> SS
RELEASE
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U19
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.7 Outgoing call / U3 MS originating call proceeding / RELEASE received
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.7.1 Definition
|
The call control entity of the MS being in the state, U3, a RELEASE message is received by the MS. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.7.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a RELEASE will return a RELEASE COMPLETE and enter the CC-state U0, "Null".
2) The MS on returning to the idle mode shall release the MM-connection and the CC-entities relating to the seven mobile originating transaction identifiers shall be in CC-state U0, "Null".
3) On releasing the MM-connection, the MS shall wait for MM layer release initiated by the network.
References
Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.4.2 and 5.4.4.
Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.5.3 and 5.5.3.2.
Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.4.4.3 and 4.5.3,
3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.13.1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.7.3 Test purpose
|
1) To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon receipt of a RELEASE will return a RELEASE COMPLETE and enter the CC-state U0, "Null".
2) To verify that the MS on returning to the idle mode releases the MM-connection and that the CC-entities relating to the seven mobile originating transaction identifiers are in CC-state U0, "Null".
3) To verify that in releasing the MM-connection, the MS shall wait for MM layer release initiated by SS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.7.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/2.
Foreseen final state of the MS
U0, null.
Maximum duration of test
1 minute 30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends a RELEASE message to the MS. The MS shall respond with a RELEASE COMPLETE message. The SS checks by using the status enquiry procedure that the CC entity has entered the state U0 with all the relevant transaction identifiers.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
RELEASE
with cause "Normal, unspecified"
2
MS -> SS
RELEASE COMPLETE
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
RELEASE COMPLETE
cause 81# (invalid TI value)
5
SS
repeat steps 3‑4 to cover all the transaction identifiers from 000...110
6
SS -> MS
CHANNEL RELEASE
the main signalling link shall be released by the MS (L2: DISC/UA).
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.8 Outgoing call / U3 MS originating call proceeding / termination requested by the user
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.8.1 Definition
|
The call control entity of the MS being in the state, U3, the user requests to terminate the call. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.8.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon request by the user to terminate will send a DISCONNECT message and enter the CC-state U11, "Disconnect Request".
References
3GPP TS 04.07 / 3GPP TS 24.007 subclause 6.2.2,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.4.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.8.3 Test purpose
|
To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", upon request by the user to terminate will send a DISCONNECT message and enter the CC-state U11, "Disconnect Request".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.8.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator: 1 cell, default parameters.
Mobile Station: The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/3.
Foreseen final state of the MS
U11, disconnect request.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The user requests termination of the call. The MS shall send a DISCONNECT message. The SS checks by using the status enquiry procedure that the CC entity has entered the state U11, disconnect request.
Expected sequence
Step
Direction
Message
Comments
1
MMI action, terminate call
2
MS -> SS
DISCONNECT
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U11
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.9 Outgoing call / U3 MS originating call proceeding / traffic channel allocation
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.9.1 Definition
|
The call control entity of the MS being in the state, U3, a traffic channel assignment procedure is performed. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.9.2 Conformance requirement
|
1) A CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", when allocated a traffic channel by the network performing the assignment procedure, shall perform a layer 2 establishment on the FACCH without changing the state of the call in progress.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.3,
3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.9.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.9.3 Test purpose
|
To verify that a CC-entity of the MS in CC-state U3, "Mobile Originating Call Proceeding", when allocated a traffic channel by the network performing the assignment procedure, performs a layer 2 establishment on the FACCH without changing the state of the call in progress.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.9.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
The MS is brought into the state U3 by using table 26.8.1.2/3.
Foreseen final state of the MS
U3, mobile originating call proceeding.
Maximum duration of test
30 s.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U3. The SS sends an ASSIGNMENT COMMAND for traffic channel to the MS. The MS shall establish layer 2 link on the newly allocated channel and respond with an ASSIGNMENT COMPLETE message. The SS checks by using the status enquiry procedure that the state of the CC entity has remained unchanged.
Expected sequence
Step
Direction
Message
Comments
1
SS -> MS
ASSIGNMENT COMMAND
(TCH) the MS shall perform L2 establishment on the FACCH
2
MS -> SS
ASSIGNMENT COMPLETE
3
SS -> MS
STATUS ENQUIRY
4
MS -> SS
STATUS
cause 30#, state U3
Specific message contents:
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.10 Outgoing call / U3 MS originating call proceeding / timer T310 time-out
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.4.10.1 Definition
|
The call control entity of the MS being in the state, U3, if no response is then received from the SS, timer T310 expires at the MS side. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.