hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.2.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
IMSI attach/detach is allowed.
The T3212 time-out value is 2/10 hour.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
- at least one MO circuit switched basic service (TSPC_AddInfo_MOsvc)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
For MS supporting at least one MO circuit switched basic service (TSPC_AddInfo_MOsvc) an MS originated MM connection is established and cleared. The channel is released. It is checked that the MS performs a periodic location updating 12 minutes after the release of the channel.
The MS is paged, it sends a CHANNEL REQUEST message and the SS responds with an IMMEDIATE ASSIGNMENT message, a call is established and then cleared. It is checked that the MS performs a periodic location updating 12 minutes after the release of the link.
Maximum duration of test
30 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS
For an MS that supports at least one MO circuit switched basic service (TSPC_AddInfo_MOsvc) a MO CM connection is attempted. An MS that does not support at least one MO circuit switched basic service skips the steps 2 to 13.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
CM SERVICE REJECT
cause #17 (network failure).
6
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
7
SS
The SS waits until the periodic location updating.
8
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall arrive between 11 minutes 45 s and 12 minutes 15 s after the last release of the RR connection by the SS.
9
SS -> MS
IMMEDIATE ASSIGNMENT
10
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = periodic.
11
SS -> MS
LOCATION UPDATING ACCEPT
12
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
13
SS
The SS waits 1 minute.
14
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" = IMSI.
15
MS -> SS
CHANNEL REQUEST
"Establishment cause": Answer to paging.
16
SS -> MS
IMMEDIATE ASSIGNMENT
17
MS -> SS
PAGING RESPONSE
18
SS -> MS
AUTHENTICATION REQUEST
19
MS -> SS
AUTHENTICATION RESPONSE
20
SS - MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
21
SS
The SS waits until the periodic location updating.
22
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall arrive between 11 minutes 45 s and 12 minutes 15 s after the last release of the RR connection by the SS.
23
SS -> MS
IMMEDIATE ASSIGNMENT
24
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = periodic.
25
SS -> MS
LOCATION UPDATING ACCEPT
26
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.3 Location updating / periodic normal / test 2
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.3.1 Conformance requirement
|
When a LOCATION UPDATING ACCEPT or a LOCATION UPDATING REJECT message is received, the timer T3212 is stopped and reset and the Mobile Station shall perform a periodic location updating after T3212 expiry.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.3.2 Test purpose
|
To verify that the MS stops and resets the timer T3212 of the periodic location updating procedure when a LOCATION UPDATING ACCEPT message is received.
NOTE: T3212 is stopped when the MM-idle state is left and restarted when the MM sublayer returns to that state, substate NORMAL SERVICE or ATTEMPTING TO UPDATE. As a consequence, the exact time when T3212 is reset between those two events cannot be tested.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.3.3 Method of test
|
Initial conditions
System Simulator:
2 cells, IMSI attach/detach is allowed in both cells.
T3212 is set to 6 minutes.
Mobile Station:
The MS has a valid TMSI. It is "idle updated" on cell A.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
- SIM removable without power down (TSPC_AddInfo_SIMRmv)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated" on cell B.
Test procedure
A normal location updating is performed. The channel is released. One minute later, the MS is deactivated, then reactivated in the same cell. It is checked that the MS performs an IMSI attach and a periodic location updating 6 minutes after the IMSI attach.
Maximum duration of test
20 minutes.
Expected sequence
Step
Direction
Message
Comments
The following messages are sent and shall be received on cell B.
1
SS
The RF level of cell A is lowered until the MS selects cell B.
2
MS -> SS
CHANNEL REQUEST
"establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS ->MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
7
SS
The SS waits until the periodic location updating.
8
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall arrive between 5 minutes 45s and 6 minutes 15 s after the last release of the RR connection by the SS.
9
SS -> MS
IMMEDIATE ASSIGNMENT
10
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = periodic.
11
SS -> MS
LOCATION UPDATING ACCEPT
12
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
13
MS
If possible (see PICS) SIM removal is performed. Otherwise if possible (see PICS) switch off is performed. Otherwise the power is removed. steps 14 to 17 may be performed or not depending on the action made in step 13.
14
MS -> SS
CHANNEL REQUEST
15
SS -> MS
IMMEDIATE ASSIGNMENT
16
MS -> SS
IMSI DETACH INDICATION
17
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
18
MS
Depending on what has been performed in step 13 the MS is brought back to operation.
19
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
20
SS -> MS
IMMEDIATE ASSIGNMENT
21
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = IMSI attach.
22
SS -> MS
LOCATION UPDATING ACCEPT
23
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
24
SS
The SS waits until the periodic location updating.
25
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall arrive between 5 minutes 45 s and 6 minutes 15s after the last release of the RR connection by the SS.
26
SS -> MS
IMMEDIATE ASSIGNMENT
27
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = periodic.
28
SS -> MS
LOCATION UPDATING ACCEPT
29
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4 Location updating / periodic HPLMN search
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.1 Location updating / periodic HPLMN search / MS waits time T
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.1.1 Conformance requirement
|
When in automatic mode and roaming in the home country, the MS shall make an attempt to access the HPLMN, if the MS is on the VPLMN at time T after since the last attempt.
NOTE: This test is not intended to test every value in the range 6 minutes to 8 hours or the default of 30 minutes, but is intended to check that the mobile is capable of using the value stored on the SIM.
References
3GPP TS 02.11 subclause 3.2.2.5.2.
3GPP TS 03.22 subclause 4.4.3.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.1.2 Test purpose
|
To verify that when a cell of the HPLMN becomes available, following the successful location request on the VPLMN of the home country and after the first search the mobile has failed to find its HPLMN, that the MS shall perform a location update request on the HPLMN after time T. Were T is the HPLMN Search Period stored in the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.1.3 Method of test
|
Initial conditions
System Simulator:
Two cells A and B, belonging to different location areas with location identification a and b. Cell A shall be a cell of the HPLMN and Cell B shall be a cell of the VPLMN with a Country Code the same as that of Cell A. Initially Cell A shall not be broadcasting. IMSI attach/detach is not allowed on either cell.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell A.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. Cell A shall be made available after 8 minutes, thus ensuring the MS fails to find the HPLMN during its first attempt. It is verified that the MS performs a location update request on Cell A, within 6 minutes after broadcasting of Cell A.
Maximum duration of test
17 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link. The SS waits a period of 8 minutes, this allowing the MS to make its first periodic search.
7
Cell A is made available.
8
SS
Within 8 minutes after step 7 the following messages shall be sent and received on Cell A.
9
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
10
SS -> MS
IMMEDIATE ASSIGNMENT
11
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": normal.
12
SS -> MS
LOCATION UPDATING ACCEPT
13
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.2 Location updating / periodic HPLMN search / MS in manual mode
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.2.1 Conformance requirement
|
The periodic attempts shall only be performed if in automatic mode when the MS is roaming in its home country.
References
3GPP TS 02.11 subclause 3.2.2.5.2.
3GPP TS 03.22 subclause 4.4.3.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.2.2 Test purpose
|
To verify that no HPLMN Search is performed when the MS is not in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.2.3 Method of test
|
Initial conditions
System Simulator:
Two cells A and B, belonging to different location areas with location identification a and b. Cell A shall be a cell of the HPLMN and Cell B shall be a cell of the VPLMN with a Country Code the same as that of Cell A. Initially Cell A shall not be broadcasting. IMSI attach/detach is not allowed on either cell.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell B.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. The MS is forced into manual selection mode. Cell A is made available. It is verified that the MS does not attempt to perform a location update on Cell A.
Maximum duration of test
7 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
8
MS
The MS is forced into manual selection mode.
If the MS triggers a new Location Update Procedure on cell B (within 30s), steps 9 to 15 apply, otherwise steps 14 and 15 only
9(optional)
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating, received on Cell B.
10 (conditional)
SS -> MS
IMMEDIATE ASSIGNMENT
11 conditional)
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
12 conditional)
SS -> MS
LOCATION UPDATING ACCEPT
13 conditional)
SS -> MS
CHANNEL RELEASE
14
SS
Cell A is made available.
15
SS
The SS waits a period of 7 minutes. During this time no messages shall be received on Cell A.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.3 Location updating / periodic HPLMN search / MS waits at least two minutes and at most T minutes
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.3.1 Conformance requirement
|
After switch on, the MS waits at least 2 minutes and at most T minutes before the first HPLMN Search is attempted.
References
3GPP TS 02.11 subclause 3.2.2.5.2.
3GPP TS 03.22 subclause 4.4.3.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.3.2 Test purpose
|
To verify that the MS waits at least 2 minutes and at most T minutes before attempting its first HPLMN Search.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.3.3 Method of test
|
Initial Conditions
System Simulator:
Two cells A and B, belonging to different location areas with location identification a and b. Cell A shall be a cell of the HPLMN and Cell B shall be a cell of the VPLMN with a Country Code the same as that of Cell A. Initially Cell A shall not be broadcasting. IMSI attach/detach is not allowed on either cell.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell A.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. Cell A is made available. It is verified that the MS attempts to perform a location update on Cell A, after at least 2 minutes and at most T minutes have passed following power on.
Maximum duration of test
8 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
8
SS
Cell A is made available.
9
SS
The SS waits a period of 2 minutes after MS is switched on. During this time no messages shall be received on Cell A. The following messages shall be sent and received on cell A. Within T minutes after step 5 the following messages shall be sent and received on cell A.
10
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall be sent between 2 and 7 minutes after step 1
11
SS -> MS
IMMEDIATE ASSIGNMENT
12
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": normal.
13
SS -> MS
LOCATION UPDATING ACCEPT
14
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
26.7.4.5.4.4 Location updating/periodic search of the higher priority PLMN, when a MS is receiving foreign country’s VPLMN/MS is in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.4.1 Conformance requirement
|
A MS in Automatic Mode shall make periodic attempts to look for a higher priority PLMN of the same country as the currently received PLMN.
References.
3GPP TS 22.011, subclause 3.2.2.5
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.4.2 Test purpose
|
To verify that the MS selects the highest priority network if the HPLMN/higher priority PLMN Search is performed, when a MS is receiving foreign country’s VPLMN and MS is in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.4.3 Method of test
|
Initial conditions
System Simulator:
Three cells A, B and C, belonging to different location areas with location identification a, b and c. Cell A shall be a cell of the HPLMN, Cell B shall be a cell of the VPLMN with a different Mobile Country Codes that of Cell A and Cell C shall be a cell of a higher priority VPLMN but of the same Mobile Country Code as Cell B. Initially Cell A and Cell C shall not be broadcasting. IMSI attach/detach is not allowed on any cell. The downlink input level setting for cells B and C shall be the same as cell A.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell C.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. The MS is in automatic selection mode. Cell A and Cell C are made available. It is verified that the MS does not attempt to perform a location update on Cell A. It is verified that the MS does perform a location update on Cell C.
Maximum duration of test
7 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
7
SS
Cell A is made available.
8
SS
Cell C is made available.
9
SS
The SS waits a period of 7 minutes. During this time no messages shall be received on Cell A but the following messages are received on Cell C.
10
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
11
SS -> MS
IMMEDIATE ASSIGNMENT
12
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
13
SS -> MS
LOCATION UPDATING ACCEPT
14
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
26.7.4.5.4.5 Location updating/periodic PLMN search in foreign country’s border areas/MS is in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.5.1 Conformance requirement
|
A MS in Automatic Mode shall make periodic attempts to look for a higher priority PLMN of the same country as the currently received PLMN. The MS shall not select a lower priority PLMN of the same country as the currently received PLMN.
References
1. 3GPP TS 22.011, subclause 3.2.2.5
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.5.2 Test purpose
|
To verify that the MS remains on the highest priority network when the HPLMN/higher priority PLMN Search is performed, if the MS is receiving a foreign country’s VPLMN and is in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.5.3 Method of test
|
Initial conditions
System Simulator:
Three cells A, B and C, belonging to different location areas with location identification a, b and c. Cell A shall be a cell of the HPLMN, Cell B shall be a cell of the VPLMN with a different Mobile Country Codes that of Cell A and Cell C shall be a cell of a lower priority VPLMN but of the same Mobile Country Code as Cell B. Initially Cell A and Cell C shall not be broadcasting. IMSI attach/detach is not allowed on any cell. The downlink input level setting for cells B and C shall be the same as cell A.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted". The PLMN Selector on the SIM shall contain entries for both PLMNs of Cell B and Cell C, where PLMN B is of a higher priority then PLMN C.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell B.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. The MS is in automatic selection mode. Cell A and Cell C are made available. It is verified that the MS does not attempt to perform a location update on Cell A or Cell C.
Maximum duration of test
7 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
7
SS
Cell A is made available.
8
SS
Cell C is made available.
9
SS
The SS waits a period of 7 minutes. During this time no messages shall be received on Cell A or C.
Specific message contents
None.
26.7.4.5.4.6 Location updating/periodic search for higher priority PLMN when the list of equivalent PLMNs includes the HPLMN, when a MS is registered in a foreign country’s VPLMN/MS is in automatic mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.6.1 Conformance requirement
|
A UE in Automatic Mode shall make periodic attempts to look for a higher priority PLMN of the same country as the currently registered PLMN. For the ranking of PLMNs the UE shall use the order used in subclause 3.2.2.2. In the case that the MS has stored a list of equivalent PLMNs, the UE shall only select a PLMN if it has a higher priority than all the PLMNs, in the list of equivalent PLMNs, which are of the same country as the currently registered PLMN
The Mobile Equipment stores a list of "equivalent PLMNs". This list is replaced or deleted at the end of each location update procedure, routing area update procedure and GPRS attach procedure. The stored list consists of a list of equivalent PLMNs as downloaded by the network plus the PLMN code of the network that downloaded the list. All PLMNs in the stored list are regarded as equivalent to each other for PLMN selection, cell selection/re-selection and handover.
References.
1. 3GPP TS 22.011, subclause 3.2.2.5
2. 3GPP TS 23.122, subclause 4.4.3
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.6.2 Test purpose
|
To verify that, in automatic mode, when registered on a VPLMN of a country different to it’s HPLMN, the MS only selects the highest priority network available from upon those of the same country as the serving PLMN. It also verifies that the MS does not take into account PLMNs, including the HPLMN, which are included in the Equivalent PLMN list.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.4.6.3 Method of test
|
Initial conditions
System Simulator:
Three cells A, B and C, belonging to different location areas with location identification a, b and c. Cell A shall be a cell of the HPLMN, Cell B shall be a cell of the VPLMN with a different Mobile Country Codes that of Cell A and Cell C shall be a cell of a higher priority VPLMN but of the same Mobile Country Code as Cell B. Initially Cell A and Cell C shall not be broadcasting. The downlink input level setting for cells B and C shall be the same as cell A. The BA list of Cell B does not include Cell A or Cell C.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated" on Cell C.
Test Procedure
Only Cell B shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell B. During the location update procedure Cell B sends an equivalent PLMN list which includes the HPLMN (Cell A). The MS is in automatic selection mode. The MS receives and store the equivalent PLMN list. The Cell A and Cell C are made available. Cell C is of a higher priority VPLMN but of the same Mobile Country Code as Cell B. It is verified that the MS does not attempt to perform a location update on Cell A. It is verified that the MS does perform a location update on Cell C.
Maximum duration of test
8 minutes.
Expected sequence
Step
Direction
Message
Contents
The following messages shall be sent and received on Cell B.
1
MS
The MS is switched on by either using the Power Switch or by applying power.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
5
SS -> MS
LOCATION UPDATING ACCEPT
The MS receives and store an equivalent PLMN list.
6
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
7
SS
Cell A is made available.
8
SS
Cell C is made available.
9
SS
The SS waits a period of 7 minutes. During this time no messages shall be received on Cell A but the following messages are received on Cell C.
10
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
11
SS -> MS
IMMEDIATE ASSIGNMENT
12
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
13
SS -> MS
LOCATION UPDATING ACCEPT
14
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
26.7.4.5.4a Location updating / periodic per-device timer
26.7.4.5.4a.1 Conformance requirement
1. In the case that the mobile has a stored "Equivalent PLMNs" list the mobile shall only select a PLMN if it is of a higher priority than those of the same country as the current serving PLMN which are stored in the "Equivalent PLMNs" list.
2. In steps i), ii) and iii) of the Automatic Network Selection Mode Procedure, the MS shall limit its attempts to access higher priority PLMNs to PLMNs of the same country as the current serving VPLMN;
3. If the MS is in idle mode in a VPLMN, the MS shall periodically attempt to obtain service on its HPLMN or higher priority PLMN listed in "user controlled PLMN selector" or "operator controlled PLMN selector". The MS shall make an attempt if the MS is on the VPLMN at time T after the last attempt.
4. If the MS is configured with the MinimumPeriodicSearchTimer, the MS shall not use a value for T that is less than the MinimumPeriodicSearchTimer. If the value stored in the SIM, or the default value for T (when no value is stored in the SIM), is less than the MinimumPeriodicSearchTimer, then T shall be set to the MinimumPeriodicSearchTimer
References
3GPP TS 23.122 subclause 4.4.3.3.
26.7.4.5.4a.2 Test purpose
To verify that if a MS is camped on a VPLMN it will perform a search for higher priority networks (e.g. HPLMN) with a periodicity of T, where T is the largest value of the Search Period stored in the SIM and the Minimum Periodic search timer, if present
This test will confirm that, if a cell from a new PLMN becomes available, within a time T the MS will perform a location updating on it only if the following requirements are met:
- The PLMN of this new cell if from the same country as the VPLMN, and
- This PLMN is the HPLMN stored in the SIM, or has a higher priority than the serving VPLMN or any PLMN from the country of the VPLMN that is stored in the equivalent PLMN list.
26.7.4.5.4a.3 Method of test
Initial conditions
System Simulator:
four cells A, B, C and D, belonging to different location areas with location identification a, b, c and d. Their country codes and mobile network codes are defined as follows:
Cell
Cell No.
MCC
MNC
A
1
001
01
B
2
022
02
C
7
001
10
D
4
001
11
E
3
001
30
If operated in GSM850 or GSM1900 the value of MNC3 shall be 1.
initially Cells A, B and C shall not be broadcasting.
Cell E is not activated.
Mobile Station:
The MS is switched off. The HPLMN Search Period on the SIM shall be set to 6 minutes. The location area information on the SIM is "deleted".
The MS is configured with the Minimum Periodic search timer that shall be set to 9 minutes.
The following SIM fields are configured:
SIM field
Priority
PLMN
EFHPLMNwAcT
1st
A
EFPLMNwAcT
1st
B
2nd
E
EFOPLMNwAcT
1st
C
2nd
D
In the table, PLMN X is the PLMN code from cell X (see above).
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated" on cell A.
Test procedure
Only Cell D shall be broadcasting. The MS shall be switched on either by using the Power Switch or by applying power. A normal location updating is performed on Cell D. The SS shall include the PLMN E in the list of equivalent PLMNs that is sent in the Location Update Accept message. Cells B and C shall be made available after 10 minutes from switched on, thus ensuring the MS fails to find any higher priority PLMN during its first attempt. It is verified that the MS does not perform a location update request on Cell B or C (waiting for at least 10 minutes after broadcasting of Cells B and C).Then Cell A is also made available, and it is verified that the MS performs a location update request on Cell A within 10 minutes after broadcasting of Cell A.
Maximum duration of test
30 minutes.
Expected sequence
Step
Direction
Message
Comments
The following messages shall be sent and received on Cell D.
1
SS
Only cell D is made available
2
MS
The MS is switched on by either using the Power Switch or by applying power.
3
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
4
SS -> MS
IMMEDIATE ASSIGNMENT
5
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": Normal.
6
SS -> MS
LOCATION UPDATING ACCEPT
"Equivalent PLMNs": PLMN E
7
SS -> MS
CHANNEL RELEASE
The SS releases the signalling connection.
8
SS
The SS waits a period of 10 minutes after the MS is switched on, allowing the MS to make its first periodic search.
9
SS
Cells B and C are made available
10
SS
The SS shall wait for 10 minutes during which no messages should be received.
11
SS
Cell A is made available
Within 10 minutes after step 10, the following messages shall be sent and received on Cell A. The lower boundary of time T shall not be checked in this test step.
12
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
13
SS -> MS
IMMEDIATE ASSIGNMENT
14
MS -> SS
LOCATION UPDATING REQUEST
"Location Update Type": normal.
15
SS -> MS
LOCATION UPDATING ACCEPT
Mobile Identity: TMSI
16
MS -> SS
TMSI REALLOCATION COMPLETE
17
SS -> MS
CHANNEL RELEASE
After sending this message the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.5 Location Updating / Multi-Band PLMN selection between different ITU regions /
|
The PLMN numbers indicated below are used in test cases to associate a cell with an MCC and MNC for that cell. The MCC used are in the range 310-316 to be considered for National Roaming (cf TS 23.122, s. 4.4.3.3 / Annex B)
Table 26.7.4.5.5-1: MNC-MCC used in System Information
type 3 messages broadcast on the BCCH
PLMN
MCC1
MCC2
MCC3
MNC1
MNC2
MNC3
Band
1 (HPLMN)
3
1
1
0
1
1
1900 (NOTE 1)
2
3
1
2
1
1
1
1900 (NOTE 1)
3
3
1
3
2
1
1
850 (NOTE 2)
4
3
1
4
3
1
F
1800 (NOTE 2)
5
3
1
5
4
1
F
900(NOTE 2)
6
3
1
6
5
1
1
1900 (NOTE 1)
7
3
1
0
6
1
1
850 (NOTE 2)
NOTE 1: the main band used is by default the 1900 band. If the MS does NOT support the 1900 band, 850 band is used instead
NOTE 2: the band used is set according to the MS supported bands:
- the 1900 band is used instead of 850 band if not supported,
- the 900 band is used instead of 1800 band if not supported,
- the 1800 band is used instead of 900 band is not supported.
The SIM used for testing is the standard SIM defined in Annex 4, except for the Following Parameters:
Table 26.7.4.5.5-2: SIM settings
SIM field
Priority
PLMN
EFLOCI
PLMN 2 (NOTE 3)
EFHHPLMN
1 (6 min)
EFPLMNsel (NOTE 4)
1st
PLMN 5
2nd
PLMN 4
3rd
PLMN 3
4th
PLMN 2
NOTE 3: Unless otherwise stated in the method of test, in all of the tests of this clause, SIM is idle updated in the PLMN 2 at the beginning of each test to achieve EFLOCI as PLMN 2.
NOTE 4: In case additional fields EFPLMNwAcT , EFOPLMNwAcT are present on the SIM they shall have same settings as EFPLMNsel.
LAC is valid and different from 0000 or FFFE (LAI is not deleted) or 0001.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.5.1 Higher Priority PLMN / Automatic PLMN Selection Mode / Normal Service
|
Conformance requirement
At switch on, or following recovery from lack of coverage, the MS selects the registered PLMN or equivalent PLMN (if it is available) using all access technologies that the MS is capable of and if necessary (in the case of recovery from lack of coverage, see clause 4.5.2) attempts to perform a Location Registration.
If successful registration is achieved, the MS indicates the selected PLMN.
If the MS is in a VPLMN, the MS shall periodically attempt to obtain service on its HPLMN (if the EHPLMN list is not present or is empty) or one of its EHPLMNs (if the EHPLMN list is present) or a higher priority PLMN/access technology combinations listed in "user controlled PLMN selector" or "operator controlled PLMN selector" by scanning in accordance with the requirements that are applicable to i), ii) and iii) as defined in the Automatic Network Selection Mode in subclause 4.4.3.1.1. In the case that the mobile has a stored "Equivalent PLMNs" list the mobile shall only select a PLMN if it is of a higher priority than those of the same country as the current serving PLMN which are stored in the "Equivalent PLMNs" list. For this purpose, a value T minutes may be stored in the SIM, T is either in the range 6 minutes to 8 hours in 6 minute steps or it indicates that no periodic attempts shall be made. If no value is stored in the SIM, a default value of 60 minutes is used.
The attempts to access the HPLMN or an EHPLMN or higher priority PLMN shall be as specified below:
a) The periodic attempts shall only be performed in automatic mode when the MS is roaming;
b) After switch on a period of at least 2 minutes and at most T minutes shall elapse before the first attempt is made;
References
TS 23.122, clause 4.4.3.1, 4.5.2 and section 4.4.3.3.1
Test purpose
To verify that in Automatic Network Selection Mode Procedure, after Power On:
1 the MS selects the Last Registered PLMN if available,
2 the MS selects the Highest Priority PLMN available (regardless of the ITU region) according to the SIM “PLMN Selector” Data
3 the MS reselects the Highest Priority PLMN available (regardless of the ITU region) according to the SIM “PLMN Selector” Data
Initial conditions
The MS is in automatic PLMN selection mode.
Cell
RF signal level [dBm]
Cell 2 / PLMN 2
-60
Cell 3 / PLMN 3
-50
Cell 4 / PLMN 4
-50
Cell 5 / PLMN 5
-50
NOTE: the Band used are defined in section 26.7.4.5.5.
The SIM parameters and the MNC-MCC used are also defined in section 26.7.4.5.5.
Specific PICS statements:
• Support of GSM 900 Band (TSPC_Type_GSM_E_Band, TSPC_Type_GSM_P_Band)
• Support of GSM 1800 Band (TSPC_Type_DCS_Band)
• Support of GSM 850 Band (TSPC_Type_GSM_850_Band)
• Support of PCS 1900 Band (TSPC_Type_PCS_Band)
PIXIT statements:
Test procedure
a) The SS activates Cell 2, Cell 3 and Cell 4 and monitors the cells for random access requests from the MS.
b) The MS is switched on.
c) The SS waits for the MS registration.
d) The SS waits for the PLMN reselection triggered by the MS
e) Cell 4 is deactivated and Cell 5 activated.
f) The SS waits for the MS registration.
Test Requirements
1. In step c), the MS must select and register on Cell 2 / PLMN 2.
2. In step d), the MS must reselect and register on Cell 4 / PLMN 4 within 2 to 6 min (± 10%) of step b).
3. In step f), the MS must select and register on Cell 5 / PLMN 5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.5.2 Higher Priority PLMN / Automatic PLMN Selection Mode / Limited Service
|
Conformance requirement
If a "PLMN not allowed" message is received by an MS in response to an LR request from a VPLMN, that VPLMN is added to a list of "forbidden PLMNs" in the SIM and thereafter that VPLMN will not be accessed by the MS when in automatic mode.
The behaviour of the MS in the roaming not allowed state is dependent on the LR reject cause as shown in table 2 in clause 5. Additionally:
- in automatic mode, "PLMN not allowed" and "roaming not allowed in this location area" cause the Automatic Network Selection procedure of clause 4.4.3.1.1 to be started;
At switch on, or following recovery from lack of coverage, the MS selects the registered PLMN or equivalent PLMN (if it is available) using all access technologies that the MS is capable of and if necessary (in the case of recovery from lack of coverage, see clause 4.5.2) attempts to perform a Location Registration.
If successful registration is achieved, the MS indicates the selected PLMN.
References
TS 23.122, clause 3.1, 4.3.3, 4.4.3.1 and section 3.5.
Test purpose
To verify that in Automatic Network Selection Mode Procedure, after Power On:
1. the MS selects the Last Registered PLMN if available
2. the MS attempts to obtain service on its HPLMN or a Higher priority PLMN when a its registration on a VPLMN is rejected with "PLMN not allowed" .
Initial conditions
The MS is in automatic PLMN selection mode.
Cell
RF signal level [dBm]
Cell 2 / PLMN 2
-60
Cell 3 / PLMN 3
-50
Cell 4 / PLMN 4
-50
NOTE: the Band used are defined in section 26.7.4.5.5.
The SIM parameters and the MNC-MCC used are also defined in section 26.7.4.5.5.
Specific PICS statements:
• Support of GSM 900 Band (TSPC_Type_GSM_E_Band, TSPC_Type_GSM_P_Band)
• Support of GSM 1800 Band (TSPC_Type_DCS_Band)
• Support of GSM 850 Band (TSPC_Type_GSM_850_Band)
• Support of PCS 1900 Band (TSPC_Type_PCS_Band)
PIXIT statements:
Test procedure
a) The SS activates Cell 2, Cell 3 and Cell 4 and monitors the cells for random access requests from the MS.
b) The MS is switched on.
c) The SS waits for the MS registration.
d) The SS reject the MS registration on Cell 2 / PLMN 2 with the cause #11 “PLMN Not allowed”
e) The SS waits for the MS registration.
Test Requirements
1. In step c), the MS must select and try to register on Cell 2 / PLMN 2.
2. In step e), the MS must reselect and register on Cell 4 / PLMN 4. Verified for 2 mins.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.5.3 Higher Priority PLMN / Automatic PLMN Selection Mode / Recovery from Lack of Service
|
Conformance requirement
At switch on, or following recovery from lack of coverage, the MS selects the registered PLMN or equivalent PLMN (if it is available) using all access technologies that the MS is capable of and if necessary (in the case of recovery from lack of coverage, see clause 4.5.2) attempts to perform a Location Registration.
If successful registration is achieved, the MS indicates the selected PLMN.
References
TS 23.122, clause 4.4.3.1.
Test purpose
To verify that in Automatic Network Selection Mode Procedure, after Power On:
1. the MS selects the Last Registered PLMN if available,
2. the MS selects the Highest Priority PLMN available (regardless of the ITU region) according to the SIM “PLMN Selector” Data
3. the MS reselects the Highest Priority PLMN available (regardless of the ITU region) according to the SIM “PLMN Selector” Data
Initial conditions
The MS is in automatic PLMN selection mode.
Cell
RF signal level [dBm]
Cell 2 / PLMN 2
-60
Cell 3 / PLMN 3
-50
Cell 4 / PLMN 4
-50
NOTE 1: the Band used are defined in section 26.7.4.5.5.
The SIM parameters and the MNC-MCC used are also defined in section 26.7.4.5.5.
Specific PICS statements:
• Support of GSM 900 Band (TSPC_Type_GSM_E_Band, TSPC_Type_GSM_P_Band)
• Support of GSM 1800 Band (TSPC_Type_DCS_Band)
• Support of GSM 850 Band (TSPC_Type_GSM_850_Band)
• Support of PCS 1900 Band (TSPC_Type_PCS_Band)
PIXIT statements:
Test procedure
a) The SS activates Cell 2 and monitors the cells for random access requests from the MS.
b) The MS is switched on.
c) The SS waits for the MS registration.
d) The SS waits 3 min and deactivates Cell 2.
e) The SS waits 2 more minutes and actives Cell 3 and Cell 4.
f) The SS waits for the MS registration.
Test Requirements
1. In step c), the MS must select and register on Cell 2 / PLMN 2.
2. In step f), the MS must select and register on Cell 4 / PLMN 4 (Note).
NOTE 2: If the MS registers first on Cell 3 / PLMN 3, it must reselect and register on Cell 4 / PLMN 4 within 6 min (+10%) of the registration on PLMN 3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.5.4 User Selection / Manual PLMN Selection Mode
|
Conformance Requirements
The user may select his desired PLMN and the MS then initiates registration on this PLMN using the access technology chosen by the user for that PLMN or using the highest priority available access technology for that PLMN, if the associated access technologies have a priority order. (This may take place at any time during the presentation of PLMNs). For such a registration, the MS shall ignore the contents of the "forbidden LAs for roaming", "forbidden LAs for regional provision of service", "forbidden PLMNs for GPRS service" and "forbidden PLMNs" lists.
NOTE 1: It is an MS implementation option whether to indicate access technologies to the user. If the MS does display access technologies, then the access technology used should be the access technology chosen by the user for that PLMN. If the MS does not display access technologies, then the access technology chosen for a particular PLMN should be the highest priority available access technology for that PLMN, if the associated access technologies have a priority order.
The MS selects and attempts registration on PLMNs, if available and allowable, in all of its bands of operation in accordance with the following order:
i) HPLMN;
ii) PLMNs contained in the " User Controlled PLMN Selector with Access Technology" data field in the SIM (in priority order) excluding the previously selected PLMN;
iii) PLMNs contained in the "Operator Controlled PLMN Selector with Access Technology" data field in the SIM (in priority order) excluding the previously selected PLMN;
iv) other PLMN/access technology combinations with the received high quality signal in random order excluding the previously selected PLMN;
v) other PLMN/access technology combinations, excluding the previously selected PLMN in order of decreasing signal quality or, alternatively, the previously selected PLMN may be chosen ignoring its signal quality;
vi) The previously selected PLMN.
The previously selected PLMN is the PLMN which the MS has selected prior to the start of the user reselection procedure.
NOTE 2: If the previously selected PLMN is chosen, and registration has not been attempted on any other PLMNs, then the MS is already registered on the PLMN, and so registration is not necessary.
References
TS 23.122, clause 4.4.3.1.2, 4.4.3.2.1
Test purpose
To verify that in Manual Network Selection Mode Procedure:
- the MS registers in the PLMN selected by the user, regardless of the ITU region.
Initial conditions
The MS is in automatic PLMN selection mode.
Cell
RF signal level [dBm]
Cell 2 / PLMN 2
-60
Cell 3 / PLMN 3
-50
Cell 4 / PLMN 4
-50
Cell 5 / PLMN 5
-50
NOTE 3: the Band used are defined in section 26.7.4.5.5.
The SIM parameters and the MNC-MCC used are also defined in section 26.7.4.5.5, except for the Last Registered PLMN being set to PLMN 1 (EFLOCI set to HPLMN) SIM is idle updated in PLMN 1.
Specific PICS statements:
• Support of GSM 900 Band (TSPC_Type_GSM_E_Band, TSPC_Type_GSM_P_Band)
• Support of GSM 1800 Band (TSPC_Type_DCS_Band)
• Support of GSM 850 Band (TSPC_Type_GSM_850_Band)
• Support of PCS 1900 Band (TSPC_Type_PCS_Band)
• Support of automatically enter automatic selection of PLMN mode.(TSPC_AddInfo_AutoAutoMode)
PIXIT statements:
-
Test procedure
a1) If the MS does not support TSPC_AddInfo_AutoAutoMode: The MS is switched On and set in Manual PLMN selection Mode and powered Off (Note 4).
a2) If the MS does support TSPC_AddInfo_AutoAutoMode: The MS is switched On and set in Manual PLMN selection Mode (Note 4).
b) The SS activates Cell 2, Cell 3, Cell 4 and Cell 5.
c) If the MS does not support TSPC_AddInfo_AutoAutoMode: The MS is switched On.
d) PLMN 4 is selected for Manual Reselection
e) The MS is set to Automatic PLMN selection mode
f) The SS waits for the MS registration.
NOTE 4: Depending on MS implementation it might be needed to activate a Cell/PLMN in order to put the MS in Manual selection mode. The Test Simulator MUST handle this case with Cell 1/ PLMN 1 if needed.
Test Requirements
1. In step c), the MS must remain in Limited Service and do not register on any of the available PLMN,
2. In step d), the MS must register on Cell 4 / PLMN 4,
3. In step f), the MS must select and register on Cell 5 / PLMN 5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.6 Location updating / periodic per-device timer
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.6.1 Conformance requirement
|
Periodic updating may be used to notify periodically the availability of the mobile station to the network. Periodic updating is performed by using the location updating procedure. The location updating type information element in the LOCATION UPDATING REQUEST message shall indicate periodic updating.
The procedure is controlled by the timer T3212 in the mobile station. The MS indicates in the MS network feature support IE whether it supports the extended value for timer T3212. If the MS receives the Per MS T3212 IE in the Location Updating Accept message, the MS shall use this IE to determine the value of T3212 instead of the value of T3212 that is broadcast.
References
3GPP TS 24.008 subclause 4.4.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.6.2 Test purpose
|
To verify that the MS uses the per-device timer value for Periodic Location Area Update broadcast by the network.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.5.6.3 Method of test
|
Initial conditions
System Simulator:
One cell, T3212 is set to 30 minutes.
IMSI attach is allowed in the cell.
Mobile Station:
The MS is deactivated. The stored MCC, MNC and LAC correspond to the broadcasted values. The stored update status is "updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
The MS is activated. It performs IMSI attach. The MS signals that it supports the extended periodic timer. The SS provides the per device timer, T3212, with a value of 6 minutes. The MS shall perform periodic location updating 6 minutes after the end of the IMSI attach procedure.
Maximum duration of test
20 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS
The MS is activated.
2
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"location updating type": IMSI attach.
“MS network feature support”: 1 (MS supports the extended periodic timer in this domain)
5
SS -> MS
LOCATION UPDATING ACCEPT
“Per MS T3212”: 6 minutes
Mobile Identity: TMSI
6
MS -> SS
TMSI REALLOCATION COMPLETE
7
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
8
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall be sent by the MS between 5minutes 45s and 6minutes 15s after step 6.
9
SS -> MS
IMMEDIATE ASSIGNMENT
10
MS -> SS
LOCATION UPDATING REQUEST
"location updating type": periodic updating.
11
SS -> MS
LOCATION UPDATING ACCEPT
12
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.6 Location updating / interworking of attach and periodic
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.6.1 Conformance requirement
|
1) If the Mobile Station is in service state NO CELL AVAILABLE, LIMITED SERVICE, PLMN SEARCH or PLMN SEARCH-NORMAL SERVICE when the timer expires the location updating procedure is delayed until this service state is left.
2) The T3212 time-out value shall not be changed in the NO CELL AVAILABLE, LIMITED SERVICE, PLMN SEARCH and PLMN SEARCH-NORMAL SERVICE states.
3) If the selected cell is in the location area where the mobile station is registered and IMSI ATTACH is not required and timer T3212 has not expired, then the state is NORMAL SERVICE.
References
1. 3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.2.
2. 3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.2.
3. 3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.2.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.6.2 Test purpose
|
1) To check that if the PLU timer expires while the MS is out of coverage, the MS informs the network of its return to coverage.
2) To check that the PLU timer is not disturbed by cells of forbidden PLMNs.
3) To check that if the PLU timer does not expire while out of coverage and if the mobile returns to the LA where it is updated, the mobile does not inform the network of its return to coverage.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.4.6.3 Method of test
|
Initial conditions
System Simulator:
Two cells, a and b, of different PLMNs.
T3212 is set to 12 minutes on cell a.
T3212 is set to 6 minutes on cell b.
IMSI attach is allowed in both cells.
Mobile Station:
The MS is deactivated. The PLMN of cell b is entered in the SIM's forbidden PLMN list.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS is "idle updated". The PLMN of cell b is entered in the SIM's forbidden PLMN list.
Test procedure
The MS is activated and placed in automatic network selection mode. It performs IMSI attach. 1 minute after the end of the IMSI attach procedure, cell a is switched off. The MS shall not location update on cell b. 8 minutes after the end of the IMSI attach procedure, cell a is switched on. The MS shall not location update on cell a before 11,75 minutes after the end of the IMSI attach procedure. The MS shall perform a periodic location update on cell a between 11,75 minutes and 12,25 minutes after the end of the IMSI attach procedure.
3 minutes after the end of the periodic location updating procedure, cell a is switched off. The MS shall not location update on cell b. 14 minutes after the end of the periodic location updating procedure, cell a is switched on and cell b is switched off. The MS shall perform a location update on cell a before 17 minutes after the end of the periodic location updating procedure.
Maximum duration of test
35 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS
The MS is activated in automatic network selection mode.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"location updating type": IMSI attach.
5
SS -> MS
LOCATION UPDATING ACCEPT
6
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
7
SS
1 minute after step 6, cell a is switched off.
8
SS
8 minutes after step 6, cell a is switched on.
9
MS -> SS
CHANNEL REQUEST
This message shall be sent by the MS between 11 minutes 45s and 12 minutes 15s after step 6.
10
SS -> MS
IMMEDIATE ASSIGNMENT
11
MS -> SS
LOCATION UPDATING REQUEST
"location updating type": periodic updating.
12
SS -> MS
LOCATION UPDATING ACCEPT
13
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
14
SS
3 minutes after step 13, cell a is switched off.
15
SS
14 minutes after step 13, cell a is switched on and cell b is switched off.
16
MS -> SS
CHANNEL REQUEST
This message shall be sent by the MS before 17 minutes after step 13.
17
SS -> MS
IMMEDIATE ASSIGNMENT
18
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = periodic.
19
SS -> MS
LOCATION UPDATING ACCEPT
22
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5 MM connection
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.1 Introduction
|
[tbd]
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.2 MM connection / establishment with cipher and repeated FACCH
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.2.1 Conformance requirement
|
The Mobile Station shall be able to correctly set up an MM connection in a Mobile Originating CM connection attempt and send a CM Service Request message with CKSN information element as stored in the SIM and Mobile Identity information element set to the TMSI.
The Mobile Station shall be able to interpret cipher mode setting as acceptance of its CM service request i.e. send a CM message.
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.5.1.1;
The MS shall, when receiving a downlink FACCH block, always attempt to decode it without combining with any previously received FACCH block.
If the current FACCH block is successfully decoded and an identical FACCH block was previously received (successfully decoded and spaced in time from the current FACCH block as specified in sub-clause 10.2), the MS shall not send the LAPDm frame of the current FACCH block to the LAPDm entity.
3GPP TS 44.006 subclause 10.4;
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.2.2 Test purpose
|
To verify that the MS can correctly set up an MM connection in an origination and interpret cipher mode setting as acceptance of its CM service request.
To verify that the MS behaves correctly when Repeated FACCH is used by the SS for LAPDm command frames, and additionally where the MS supported repeated FACCH for LAPDm response frames.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.2.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
• at least one half rate service (TSPC_AddInfo_HalfRate)
• Support of Repeated FACCH (TSPC_Repeated_FACCH)
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN. It is "idle updated".
Test Procedure
A mobile originating CM connection is initiated. After the MS has sent the CM SERVICE REQUEST message to the SS, an authentication procedure and a ciphering mode setting procedure are performed. Then, the MS sends a CM message and the SS clears the call and releases the channel.
For k=2 and k=3, the SS shall activate Repeated FACCH for LAPDm command frames on FACCH.
If the MS supports Repeated FACCH, the SS shall additionally activate Repeated FACCH for LAPDm response frames on FACCH. It is checked by the SS that the MS does not respond to identical FACCH blocks which are repeated.
If the MS does not support Repeated FACCH, the MS may respond to the identical FACCH blocks which are repeated, with a REJ frame.
This test is repeated for:
k=1;
k=2;
k=3 where the MS supports at least one half rate service.
Maximum duration of test
3 minute.
Expected sequence
Step
Direction
Message
Comments
If the MS supports Repeated FACCH (TSPC_Repeated_FACCH), the SS shall check that the MS does not respond to identical FACCH blocks which are repeated.
If the MS does not support Repeated FACCH (TSPC_Repeated_FACCH), the MS may respond to the identical FACCH blocks which are repeated, with a REJ frame.
1
MS
A MO CM connection is attempted.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
See specific message contents.
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
7
SS -> MS
CIPHERING MODE COMMAND
The SS starts deciphering.
8
MS -> SS
CIPHERING MODE COMPLETE
The SS starts enciphering.
A9
MS -> SS
SETUP
A10
SS -> MS
RELEASE COMPLETE
"Cause" IE: "unassigned number".
B9
MS -> SS
REGISTER
B10
SS -> MS
RELEASE COMPLETE
C9
MS -> SS
CP-DATA
C10
SS -> MS
CP-ACK
C11
SS -> MS
CP-DATA
C12
MS -> SS
CP-ACK
C13
SS -> MS
RELEASE COMPLETE
14
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
IMMEDIATE ASSIGNMENT
Information Element
value/remarks
Channel description
k=1: SDCCH
k=2: TCH/F
k=3: TCH/H
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.3 MM connection / establishment without cipher
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.3.1 Conformance requirement
|
Upon reception of the CM SERVICE ACCEPT message, the MS shall send a CM message.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.5.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.3.2 Test purpose
|
To verify that the MS can correctly set up an MM connection in an originating CM connection establishment when ciphering mode setting is not required.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.3.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test Procedure
A mobile originating CM connection is attempted. The MM-connection is established without invoking the ciphering mode setting procedure.
Then, the MS sends a CM message and the SS releases the channel.
Maximum duration of test
one minute.
Expected sequence
Step
Direction
Message
Comments
1
MS
A MO CM connection is attempted.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
CM SERVICE ACCEPT
A6
MS -> SS
SETUP
B6
MS -> SS
REGISTER
C6
MS -> SS
CP-DATA
C7
SS -> MS
CP-ACK
C8
SS -> MS
CP-DATA
C9
MS -> SS
CP-ACK
10
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.4 MM connection / establishment rejected
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.4.1 Conformance requirement
|
Upon reception of a CM SERVICE REJECT message, the MS shall not send any layer 3 message, start timer T3240 and enter the "wait for network command" state.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.5.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.4.2 Test purpose
|
To verify that the MS does not send a layer 3 message when the service request is rejected by the SS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.4.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI; It is "idle updated".
Test Procedure
A mobile originating CM connection is attempted. After the MS has sent the CM SERVICE REQUEST message to the SS, the SS responds with a CM SERVICE REJECT message with reject cause "requested service option not subscribed". It is checked that the MS does not send a layer 3 message.
Maximum duration of test
1 minute.
Expected sequence
Step
Direction
Message
Comments
1
MS
A MO CM connection is attempted
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
CM SERVICE REJECT
"Reject cause" IE: "requested service option not subscribed".
6
SS
The MS shall not send a layer 3 message. This is checked during 5 s.
7
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.5 MM connection / establishment rejected cause 4
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.5.1 Conformance requirement
|
1) The Mobile Station shall be able to correctly set up an MM connection in a Mobile Originating CM connection attempt and send a CM Service Request message with CKSN information element as stored in the SIM and Mobile Identity information element set to the TMSI.
2) The Mobile Station, when receiving a CM SERVICE REJECT message with reject cause "IMSI unknown in VLR" shall wait for the network to release the RR connection.
3) The Mobile Station shall then be able to perform a location updating procedure.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.5.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.5.2 Test purpose
|
To verify that the MS can correctly accept a CM SERVICE REJECT message with reject cause "IMSI unknown in VLR".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.5.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has valid TMSI, CKSN. It is "idle updated".
Test Procedure
A mobile originating CM connection is attempted. After the MS has sent the CM SERVICE REQUEST message to the SS, the SS responds with a CM SERVICE REJECT message with reject cause "IMSI unknown in VLR". On receipt of this message, the MS shall delete any TMSI, LAI, cipher key and cipher key sequence number. The channel is released. It is checked that the MS performs a normal location updating procedure.
Maximum duration of test
One minute.
Expected sequence
Step
Direction
Message
Comments
1
MS
A MO CM connection is attempted.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
CM SERVICE REJECT
"Reject cause" = "IMSI unknown in VLR".
6
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
7
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
8
SS -> MS
IMMEDIATE ASSIGNMENT
9
MS -> SS
LOCATION UPDATING REQUEST
"Ciphering key sequence number" = "No key is available". "Mobile identity" = IMSI. "Location area identification" = deleted LAI (the MCC and MNC hold the previous values, the LAC is coded FFFE).
10
SS -> MS
AUTHENTICATION REQUEST
11
MS -> SS
AUTHENTICATION RESPONSE
12
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile identity" = new TMSI.
13
MS -> SS
TMSI REALLOCATION COMPLETE
14
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.6 MM connection / expiry T3230
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.6.1 Conformance requirement
|
At T3230 expiry (i.e. no response is given but an RR connection is available) the MM connection establishment shall be aborted.
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 4.5.1.2 and 11.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.6.2 Test purpose
|
To verify that at T3230 expiry, the MS aborts the MM-connection establishment.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.6.3 Method of test
|
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS has a valid TMSI. It is "idle updated".
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test Procedure
A mobile originating CM connection is attempted. After the MS has sent the CM SERVICE REQUEST message to the SS, the SS waits for expiry of timer T3230. It is checked that the MS does not send a layer 3 message but waits for the release of the RR-connection.
Maximum duration of test
1 minute.
Expected sequence
Step
Direction
Message
Comments
1
MS
A MO CM connection is attempted.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS
The SS waits for expiry of timer T3230.
6
SS -> MS
CM SERVICE ACCEPT
7
MS -> SS
MM STATUS
"Reject cause” IE is "message not compatible with the call state or not implemented".
8
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7 MM connection / abortion by the network
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.1 MM connection / abortion by the network / cause #6
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.1.1 Conformance requirement
|
1) Upon reception of an ABORT message, the MS shall release any ongoing MM connection and enter the "wait for network command" state.
2) If the cause in the ABORT message was cause #6, the Mobile Station shall:
2.1 not perform normal location updating;
2.2 not perform periodic location updating;
2.3 not respond to paging with TMSI;
2.4 reject any request for Mobile Originating call establishment except Emergency call;
2.5 not perform IMSI detach if deactivated.
3) After reception of an ABORT message with cause #6, the Mobile Station, if it supports speech, shall accept a request for an emergency call by sending a Channel Request message with the establishment cause set to "emergency call".
4) After reception of an ABORT message with cause #6, the Mobile Station shall delete the stored LAI, CKSN and TMSI.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.3.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.1.2 Test purpose
|
To check that upon reception of an ABORT message with cause #6 during call establishment:
- the MS does not send any layer 3 message;
- after reception of an ABORT message and after having been deactivated and reactivated, the MS performs location updating using its IMSI as mobile identity and indicates deleted LAI and CKSN;
- the MS does not perform location updating, does not answer to paging with TMSI, rejects any request for mobile originating call except emergency call, does not perform IMSI detach;
- the MS accepts a request for emergency call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.1.3 Method of test
|
Initial Conditions
System Simulator:
2 cells, default parameters.
Mobile Station:
The MS has a valid TMSI, CKSN and Kc. It is "idle updated" on cell B.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
- SIM removable without power down (TSPC_AddInfo_SIMRmv)
- Speech supported for Full rate version 1 (GSM FR) (TSPC_AddInfo_Full_rate_version_1)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated" on cell A.
Test procedure
A mobile originating CM connection is attempted. Upon reception of the AUTHENTICATION RESPONSE message, the SS sends an ABORT message with cause #6. The SS waits for 5 s. The MS shall not send any layer 3 message. The SS releases the RR connection.
The SS checks that the MS has entered the state MM IDLE substate NO IMSI, i.e. does not perform normal location updating, does not perform periodic updating, does not respond to paging, rejects any requests from CM entities except emergency calls and does not perform IMSI detach if deactivated.
Maximum Duration Of Test
10 minutes.
Expected Sequence
Step
Direction
Message
Comments
The following messages are sent and shall be received on cell B
1
MS
A mobile originating CM connection is attempted.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
CM SERVICE REQUEST
5
SS -> MS
AUTHENTICATION REQUEST
6
MS -> SS
AUTHENTICATION RESPONSE
7
SS -> MS
ABORT
"reject cause" = #6.
8
SS
The SS waits for 5 s.
9
MS
The MS shall not send any layer 3 message during that time.
10
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
The following messages are sent and shall be received on cell A.
11
SS
The RF levels are changed to make the MS reselect cell A.
12
MS
The MS performs cell reselection according to procedure as specified in 3GPP TS 05.08 (this however is not checked until step 22). The MS shall not initiate an RR connection establishment on cell A or on cell B.
13
SS
The SS waits at least 7 minutes for a possible periodic updating.
14
MS
The MS shall not initiate an RR connection establishment on cell A or on cell B.
15
SS -> MS
PAGING REQUEST TYPE 1
"Mobile identity" IE contains TMSI.
16
MS
The MS shall not initiate an RR connection establishment on cell A or on cell B. This is verified during 3 s.
17
MS
A MO CM connection is attempted.
18
MS
The MS shall not initiate an RR connection establishment on cell A or on cell B. This is checked during 3 s.
19
MS
If the MS supports speech (see PICS), an emergency call is attempted.
20
MS -> SS
CHANNEL REQUEST
"Establishment cause": Emergency call.
21
SS -> MS
IMMEDIATE ASSIGNMENT
22
MS -> SS
CM SERVICE REQUEST
"CM service type": Emergency call establishment.
23
SS -> MS
CM SERVICE ACCEPT
24
MS -> SS
EMERGENCY SETUP
25
SS -> MS
RELEASE COMPLETE
"Cause" = unassigned number.
26
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
27
MS
If possible (see PICS) SIM detachment is performed. Otherwise if possible (see PICS) switch off is performed. Otherwise the power is removed.
28
MS
The MS shall not initiate an RR connection establishment on cell A or on cell B. This is checked during 3 s.
29
MS
Depending on what has been performed in step 29 the MS is brought back to operation.
30
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating.
31
SS -> MS
IMMEDIATE ASSIGNMENT
32
MS -> SS
LOCATION UPDATING REQUEST
"location updating type" = normal, "CKSN" = no key available, "Mobile Identity" = IMSI, "LAI" = deleted LAI (the MCC and MNC hold the previous values, the LAC is coded FFFE).
33
SS -> MS
AUTHENTICATION REQUEST
"CKSN" = CKSN1.
34
MS -> SS
AUTHENTICATION RESPONSE
35
SS -> MS
LOCATION UPDATING ACCEPT
"Mobile Identity" = TMSI.
36
MS -> SS
TMSI REALLOCATION COMPLETE
37
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.2 MM connection / abortion by the network / cause not equal to #6
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.2.1 Conformance requirement
|
Upon reception of an ABORT message, the MS shall release any ongoing MM connection and enter the "wait for network command" state.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.3.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.2.2 Test purpose
|
1. When multiple MM connections are established, the MS releases all MM connections upon reception of an ABORT message, in the case when the two MM connections are established for a mobile terminating call and a non call related supplementary service operation.
2. The TMSI isn’t deleted from MS after reception of ABORT message with cause another than #6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.7.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, default parameters.
T3212 is set to 6 minutes.
Mobile Station:
The MS is in state U10 of a mobile terminating call.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
A non call related supplementary service operation is attempted at the MS. Upon reception of the REGISTER message, the SS sends an ABORT message with cause # 17. The SS waits for 5 s. The MS shall not send any layer 3 message. The SS releases the RR connection. The MS shall perform periodic location updating 6 minutes after the CHANNEL RELEASE message. TMSI shall be used as an MS Identity in LOCATION UPDATING REQUEST
Maximum Duration Of Test
15 minutes.
Expected Sequence
This procedure is performed if the MS supports non call related supplementary service operation.
Step
Direction
Message
Comments
1
MS
A non call related supplementary service operation is attempted at the MS.
2
MS -> SS
CM SERVICE REQUEST
3
SS -> MS
CM SERVICE ACCEPT
4
MS -> SS
REGISTER
5
SS -> MS
ABORT
"reject cause" = #17.
6
SS
The SS waits for 5 seconds. The MS shall not send any layer 3 message during that time.
7
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
8
MS -> SS
CHANNEL REQUEST
"Establishment cause": Location updating This message shall be sent by the MS between 5minutes 45s and 6minutes 15s after step 7.
9
SS -> MS
IMMEDIATE ASSIGNMENT
10
MS -> SS
LOCATION UPDATING REQUEST
"location updating type": periodic updating. Mobile identity IE specifies the TMSI of the MS.
11
SS -> MS
LOCATION UPDATING ACCEPT
12
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8 MM connection / follow-on request pending
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.1 MM connection / follow-on request pending / test 1
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.1.1 Conformance requirement
|
The MS shall not attempt to establish a new MM connection after location updating on the same RR connection if not allowed by the network.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.4.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.1.2 Test purpose
|
To check that when the network does not include the follow on proceed IE in a LOCATION UPDATING ACCEPT message, a MS that has a CM application request pending does not attempt to establish a new MM connection on that RR connection.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.1.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, ATT flag is set to "MSs in the cell shall apply IMSI attach and detach procedure".
Mobile Station:
The MS has a valid TMSI and is deactivated.
Specific PICS statements:
-
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
The MS is activated and a CM connection is attempted during the location updating procedure. The SS does not include the follow on proceed information element in the LOCATION UPDATING ACCEPT message. The SS waits for at least 8 seconds. The MS shall not send any layer 3 message for 8 seconds.
Maximum Duration of Test
60 s.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The MS is activated.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
location updating type = IMSI attach.
Then the SS waits for 15 s. During this delay a CM connection is attempted.
5
SS -> MS
LOCATION UPDATING ACCEPT
follow on proceed IE not included.
6
SS
The SS wait for at least 8 seconds.
7
MS
The MS shall not send any layer 3 message for 8 seconds after reception of the LOCATION UPDATING ACCEPT message.
8
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.2 MM connection / follow-on request pending / test 2
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.2.1 Conformance requirement
|
A MS supporting the follow-on request procedure and having a CM connection request pending shall correctly establish an MM connection following a location update when allowed by the network.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.4.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.2.2 Test purpose
|
To check that when the network includes the follow on proceed IE in a LOCATION UPDATING ACCEPT message, a MS that supports the follow on request procedure and that has a CM application request pending establishes successfully a new MM connection on that RR connection.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.2.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, ATT flag is set to "MSs in the cell shall apply IMSI attach and detach procedure".
Mobile Station:
The MS has a valid TMSI and is deactivated.
Specific PICS statements:
- follow-on request procedure (TSPC_AddInfo_followOnReq)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
The MS is activated and a CM connection is attempted during the location updating procedure. The SS includes the follow on proceed information element in the LOCATION UPDATING ACCEPT message. The SS waits for at least 8 seconds.
If the MS supports the follow on request procedure:
The MS shall send a CM SERVICE REQUEST. Upon reception of that message, the SS sends a CM SERVICE ACCEPT message. The MS shall send an initial CM message. Upon reception of that message, the SS releases the RR connection.
If the MS does not support the follow on request procedure:
The MS shall not send any layer 3 message for 8 seconds.
Maximum Duration of Test
60 s.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The MS is activated.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
Location updating type = IMSI attach.
Then the SS waits for 15 s. During this delay a CM connection is attempted.
5
SS -> MS
LOCATION UPDATING ACCEPT
follow on proceed IE included.
If the MS supports the follow on request procedure (see PICS) steps A6 to A8 are performed, otherwise steps B6 to B7 are performed.
A6
MS -> SS
CM SERVICE REQUEST
A7
SS ->MS
CM SERVICE ACCEPT
A8
MS -> SS
An initial CM message
B6
SS
The SS wait for at least 8 seconds.
B7
MS
The MS shall not send any layer 3 message for 8 seconds after reception of the LOCATION UPDATING ACCEPT message.
9
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.3 MM connection / follow-on request pending / test 3
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.3.1 Conformance requirement
|
1) The MS shall not set the follow on request bit in a LOCATION UPDATING REQUEST message if no MM connection request is pending.
2) When the network includes the follow on proceed IE in a LOCATION UPDATING ACCEPT message, a MS that has no CM application request pending shall not attempt to establish a new MM connection on that RR connection.
3) The MS shall correctly handle a CM connection established by the network on the RR connection that was used for the location updating procedure.
Reference(s)
3GPP TS 04.08 / 3GPP TS 24.008 subclause 4.4.4.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.3.2 Test purpose
|
1) To check that a MS that has no CM application request pending sets the Follow-On-Request bit to No follow-on request pending in a LOCATION UPDATING REQUEST message.
2) To check that when the network includes the follow on proceed IE in a LOCATION UPDATING ACCEPT message, a MS that has no CM application request pending does not attempt to establish a new MM connection on that RR connection.
3) To check that the MS accepts establishment by the network of a new MM connection on the existing RR connection.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.5.8.3.3 Method of test
|
Initial Conditions
System Simulator:
1 cell, ATT flag is set to "MSs in the cell shall apply IMSI attach and detach procedure".
Mobile Station:
The MS has a valid TMSI and is deactivated.
Specific PICS statements:
- at least one MO circuit switched basic service (TSPC_AddInfo_MOsvc)
PIXIT statements:
-
Foreseen final state of the MS
The MS has a valid TMSI. It is "idle updated".
Test procedure
The MS is activated. The MS performs location updating. The MS shall set the FOR bit to No follow-on request pending in the LOCATION UPDATING REQUEST message. The SS includes the follow on proceed information element in the LOCATION UPDATING ACCEPT message. The SS waits for 5 s. The MS shall not send any layer 3 message for 5 s. The SS sends a SETUP message to the MS requesting a basic service supported by the MS. The MS shall send either a CALL CONFIRMED message if it supports a service on TCH or a RELEASE COMPLETE with cause #88.
Maximum Duration of Test
20 s.
Expected Sequence
Step
Direction
Message
Comments
1
MS
The MS is activated.
2
MS -> SS
CHANNEL REQUEST
3
SS -> MS
IMMEDIATE ASSIGNMENT
4
MS -> SS
LOCATION UPDATING REQUEST
"Location updating type" = IMSI attach. The FOR bit is set to No follow-on request pending.
5
SS -> MS
LOCATION UPDATING ACCEPT
follow on proceed IE is included.
6
SS
The SS wait for 5 s.
7
MS
The MS shall not send any layer 3 message for 5 s after reception of the LOCATION UPDATING ACCEPT message.
8
SS -> MS
SETUP
If the MS supports a basic service on TCH.
A9
MS -> SS
CALL CONFIRMED
If the MS does not support any basic service on TCH.
B9
MS -> SS
RELEASE COMPLETE
cause #88.
10
SS -> MS
CHANNEL RELEASE
After the sending of this message, the SS waits for the disconnection of the main signalling link.
Specific message contents
None.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6 Network Identity and Time zone (NITZ)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6.1 NITZ and CS location update procedures
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6.1.1 NITZ / CS location update / Time zone, Time and DST Handling
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6.1.1.1 Conformance requirement
|
The feature Network Identities and Time zone shall make it possible for a serving PLMN to transfer its current identity, universal time, DST and LTZ to MSs, and for the MS to store and use this information. Each one of these elements is optional. The feature significantly enhances roaming as it enables the accurate indication of network identities that are either newer than the ME or have changed their name since the ME was manufactured or sold. Additionally time and time zone information can be utilised by MEs as desired.
The serving PLMN shall make Local Time Zone (LTZ) available to the MS as an offset from Universal Time in units of 15 minutes.
When the LTZ is compensated for DST (summertime), the serving PLMN shall provide a DST parameter to indicate this. The adjustment for DST can be +1h or +2h.
The Time Zone code enables the receiver to calculate the equivalent time in GMT from the other semi‑octets in the Service‑Centre‑Time‑Stamp, or indicate the time zone (GMT, GMT+1H etc.), or perform other similar calculations as required by the implementation. The value contained in the Time Zone field must take into account daylight saving time, such that when the sending entity changes from regular (winter) time to daylight saving (summer) time, there is a change to the value in the Time Zone field.
The mobile station should assume that this time zone applies to the Location Area of the cell to which the Channel Request message was sent.
If the local time zone has been adjusted for Daylight Saving Time, the network shall indicate this by including the IE Network Daylight Saving Time.
The network may be able to select particular instants where it can send the MM INFORMATION message without adding delay to, or interrupting, any CM layer transaction, e.g. immediately after the AUTHENTICATION REQUEST message.
Reference(s):
3GPP TS 02.42 / 3GPP TS 22.042 subclause 4
3GPP TS 03.40 / 3GPP TS 23.040 subclause 9.2.3.11
3GPP TS 04.08 / 3GPP TS 24.008 subclause 9.4.19.4, 4.3.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6.1.1.2 Test purpose
|
To verify that a MS supporting any of the NITZ Time related feature (Local Time Zone, Universal Time and DST IE and thus MM Information) is able to handle them properly.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.7.6.1.1.3 Method of test
|
Initial conditions
System Simulator:
One cell (cell A)
IMSI attach/detach allowed in the cell
Mobile Station:
The MS has a valid IMSI. MS is powered off.
Specific PICS statements:
- On/Off switch (TSPC_Feat_OnOff)
- Use of NITZ DST (TSPC_NITZ_DST)
- Use of NITZ Universal Time for PLMN (TSPC_NITZ_Universal_Time)
- Use of NITZ Local Time Zone for PLMN (TSPC_NITZ_Time_Zone)
PIXIT statements:
-
Test procedure
During the Location Update procedure on Cell A, SS sends its local time and date (UK, Winter Time) using the MM INFORMATION Message to the MS. The operator verifies then the supported parameters and/or the time and date stored in the MS.
The MS is powered off and then powered on. During the location update the SS sets local time and date (UK, Summer Time). The operator verifies then the supported parameters and/or the time and date stored in the MS.
This is then repeated for the follow scenarios: US East coast summer time (GMT–5+1), US West coast summer time (GMT–8+1), US Mountain time (no summer adjustment) (GMT–7).
Maximum duration of test
10 minutes.
Expected sequence
Step
Direction
Message
Comments
1
MS
The MS is powered up or switched on (see PICS) and initiates a location update.
2
MS -> SS
LOCATION UPDATE REQUEST
3
SS -> MS
AUTHENTICATION REQUEST
4
MS -> SS
AUTHENTICATION RESPONSE
5
SS ->MS
MM INFORMATION
Universal Time IE is included:
“< Current Year >/ 12/31 06:25:00” for UT
“0 hour” for Timezone
Local Time Zone IE included:
“0 hour” for Timezone
No DST IE included
See specific message content
6
SS -> MS
LOCATION UPDATE ACCEPT
7
MS
Operator Action:
The use of the supported Fields is checked:
Universal Time:
Year: < Current Year >
Month: December
Day: 31st
Hour: 6 Hours
Minute: 25 Minutes
Timezone: GMT+0
Local Time Zone:
Timezone: GMT+0
DST:
Daylight Saving Time not in use (i.e. winter time)
cf note
8
MS
The MS is switched off or power is removed (see PICS).
9
MS -> SS
IMSI DETACH
Message not sent if power is removed.
Detach type = IMSI detach
10
MS
The MS is powered up or switched on (see PICS) and initiates a location update.
11
MS -> SS
LOCATION UPDATE REQUEST
12
SS -> MS
AUTHENTICATION REQUEST
13
MS -> SS
AUTHENTICATION RESPONSE
14
SS ->MS
MM INFORMATION
Universal Time IE is included:
“< Current Year >/ 12/31 06:25:00” for UT
“1 hour” for Timezone (including DST)
DST = +1 hour
See specific message content
15
SS -> MS
LOCATION UPDATE ACCEPT
16
MS
Operator Action:
The use of the supported Fields is checked:
Universal Time:
Year: < Current Year >
Month: December
Day: 31st
Hour: 7 Hours
Minute: 25 Minutes
Timezone: GMT+0
Local Time Zone:
Not sent
DST:
Daylight Saving Time in use (i.e. summer time)
cf note
17
MS
The MS is switched off or power is removed (see PICS).
18
MS -> SS
IMSI DETACH
Message not sent if power is removed.
Detach type = IMSI detach
19
MS
The MS is powered up or switched on (see PICS) and initiates a location update.
20
MS -> SS
LOCATION UPDATE REQUEST
21
SS -> MS
AUTHENTICATION REQUEST
22
MS -> SS
AUTHENTICATION RESPONSE
23
SS ->MS
MM INFORMATION
UniversalTime IE is included:
“< Current Year >/ 12/31 06:25:00” for UT
“-4 hours” for Timezone (including DST)
DST = +1 hour
See specific message content
24
SS -> MS
LOCATION UPDATE ACCEPT
25
MS
Operator Action:
The use of the supported Fields is checked:
Universal Time:
Year: < Current Year >
Month: December
Day: 31st
Hour: 2 Hours
Minute: 25 Minutes
Timezone: GMT-5
Local Time Zone:
Not sent
DST:
Daylight Saving Time in use (i.e. summer time)
cf note
26
MS
The MS is switched off or power is removed (see PICS).
27
MS -> SS
IMSI DETACH
Message not sent if power is removed.
Detach type = IMSI detach
28
MS
The MS is powered up or switched on (see PICS) and initiates a location update.
29
MS -> SS
LOCATION UPDATE REQUEST
30
SS -> MS
AUTHENTICATION REQUEST
31
MS -> SS
AUTHENTICATION RESPONSE
32
SS ->MS
MM INFORMATION
Universal Time IE is included:
“< Current Year >/ 12/31 06:25:00” for UT
“-7 hours” for Timezone (including DST)
DST = +1 hour
See specific message content
33
SS -> MS
LOCATION UPDATE ACCEPT
34
MS
Operator Action:
The use of the supported Fields is checked:
Year: < Current Year >
Month: December
Day: 31st
Hour: 23 Hours
Minute: 25 Minutes
Timezone: GMT-8
Local Time Zone:
Not sent
DST:
Daylight Saving Time in use (i.e. summer time)
cf note
35
MS
The MS is switched off or power is removed (see PICS).
36
MS -> SS
IMSI DETACH
Message not sent if power is removed.
Detach type = IMSI detach
37
MS
The MS is powered up or switched on (see PICS) and initiates a location update.
38
MS -> SS
LOCATION UPDATE REQUEST
39
SS -> MS
AUTHENTICATION REQUEST
40
MS -> SS
AUTHENTICATION RESPONSE
41
SS ->MS
MM INFORMATION
Universal Time IE is included:
“< Current Year >/ 12/31 06:25:00” for UT
“-7 hour” for Timezone
No DST IE included
See specific message content
42
SS -> MS
LOCATION UPDATE ACCEPT
43
MS
Operator Action:
The use of the supported Fields is checked:
Universal Time:
Year: < Current Year >
Month: DecemberMay
Day: 31st
Hour: 23 Hours
Minute: 25 Minutes
Timezone: GMT-7
Local Time Zone:
No sent
DST:
Daylight Saving Time not in use (i.e. winter time)
cf note
44
MS
The MS is switched off or power is removed (see PICS).
45
MS -> SS
IMSI DETACH
Message not sent if power is removed.
Detach type = IMSI detach
Note: In steps 7, 16, 25, 34 and 43 the “minute” is not so relevant and can be higher than “25” depending on operator’s action time.
Current Year is derived by the SS.
The check of Timezone and DST is done implicitly by checking the time only in case MS does not support the display of these two fields.
Specific message contents
MM Information on step 5:
Information element
Value/remark
Universal Time IE
47
Year
< Current Year >
Month
21 – December
Day
13 - 31st
Hour
60 - 6 hours
Minute
52 - 25 Minutes
Second
00 - 0 second
Time Zone
00 - GMT+0 (0*15 minutes + 0*15 minutes DST)
Local Time Zone IE
46
Time Zone
00 - GMT+0 (0*15 minutes + 0*15 minutes DST)
MM Information on step 14:
Information element
Value/remark
UniversalTime IE
47
Year
< Current Year >
Month
21 - December
Day
13 - 31st
Hour
60 - 6 hours
Minute
52 - 25 Minutes
Second
00 - 0 second
Time Zone
40 - GMT+0+1 (0*15 minutes + (1*4)*15 minutes DST)
Daylight Saving Time IE
49
Length of DST Content
1
Value
1 - + 1 hour (summer time)
MM Information on step 23:
Information element
Value/remark
Universal Time IE
47
Year
< Current Year >
Month
21 - December
Day
13 - 31st
Hour
60 - 6 hours
Minute
52 - 25 Minutes
Second
00 - 0 second
Time Zone
69 - GMT-5+1 ((-5*4)*15 minutes + (1*4)*15 minutes DST)
Daylight Saving Time IE
49
Length of DST Content
1
Value
1 - + 1 hour (summer time)
MM Information on step 32:
Information element
Value/remark
UniversalTime IE
47
Year
< Current Year >
Month
21 – December
Day
13 - 31st
Hour
60 - 6 hours
Minute
52 - 25 Minutes
Second
00 - 0 second
Time Zone
8A - GMT-8+1 ((-8*4)*15 minutes + (1*4)*15 minutes DST)
Daylight Saving Time IE
49
Length of DST Content
1
Value
1 - + 1 hour (summer time)
MM Information on step 41:
Information element
Value/remark
Universal Time IE
47
Year
< Current Year >
Month
21 – December
Day
13 - 31st
Hour
60 - 6 hours
Minute
52 - 25 Minutes
Second
00 - 0 second
Time Zone
8A - GMT-7 ((-7*4)*15 minutes)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8 Tests related to circuit switched call control
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1 Circuit switched Call Control (CC) state machine verification
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.1 General on CC state machine verification
|
The principle of checking the call control functions consists in the validation of each call control identified state.
State U0 as an initial state is not verified in the tests of 26.8.1.2 (establishment of an outgoing call).
State U0.1 is never verified.
The steps to be followed within each performed test are:
- bring the MS into the required state;
- trigger the tested event;
- check the MS response and new state.
In subclauses 26.8.1.2 and 26.8.1.3 different tables are defined to bring the MS into the required initial state. The exact table to be chosen is specified individually in subclause "Initial conditions" of "Method of test" for each test case.
For each test, unless otherwise specified, a circuit switched basic service among those supported by the MS but excluding the emergency call teleservice shall be chosen arbitrarily, and the test shall be performed according to that basic service. If the only circuit switched basic service supported by the mobile is emergency call, then the incoming call tests shall not be performed and the other call control tests shall be performed with the EMERGENCY SETUP message replacing the SETUP message.
The initial states are to be checked through STATUS ENQUIRY messages sent by the SS, when feasible. This is not explicitly stated in the tables of expected sequences of signalling messages. The checking of final states are explicitly included into the expected sequences of signalling messages.
The following postamble may be used by the SS to bring MS back to idle mode in those test cases, in which it is not already included into expected sequence of signalling messages:
Table 26.8.1.1/1: A postamble to bring the MS back to idle mode.
Step
Direction
Message
Comments
n
SS -> MS
CHANNEL RELEASE
n+1
MS
the MS shall release the main signalling link (DISC/UA)
The postamble has not been included into the all of the tests in order to leave an option to concatenate the procedures in the future by using a final state of a test case as an initial state to another one.
For the special case of U0, the state is checked by sending STATUS ENQUIRY message with all possible values of transaction identifier (seven values) as U0 is the only state in which for every TI the MS will answer with release complete with cause #81. If U0 is to be verified when no RR connection exists, first a mobile terminating radio connection must be established.
The MS responses are either call management messages received by the SS or lower layers functions activated within the MS or MMI actions (e.g. the buzzing of an alerting tone).
A time-out within the MS is triggered by the SS when it does not answer back an MS expected response.
The test sequences may be split in 3 main groups:
- establishment and release of an outgoing call;
- establishment and release of an incoming call;
- in-call functions.
Remark on verification of transient states:
Some call control states of the mobile station may be transient, depending on implementation, configuration of the MS and previous messages (see annex 3, subclause 3.1.6).
If a test starts in a transient state, then the test is executed without verification of the starting state.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2 Establishment of an outgoing call
|
Initial conditions
As a minimum requirement the MS is updated and has been given a TMSI, a ciphering key and cipher key sequence number, and the layer 2, RR and MM functionalities have been verified.
There are as many CM initial conditions as states to be checked.
The tables below describe message exchanges which bring the MS in the requested initial states.
A state may be taken as initial only when all the states which lead to this initial state have been validated. The order followed in the test procedure will be U0, U0.1, U1, U3, U4, U10, U12, U19, U11 as seen in the table underneath.
The MS is brought again in the initial state starting with U0 at each new test performed.
Table 26.8.1.2/1: Establishment of an outgoing call, procedure 1 (late assignment)
Step
Direction
Message
Comments/actions/next state
1
MS -> SS
CHANNEL REQUEST
initiate outgoing call
2
SS -> MS
IMMEDIATE ASSIGNMENT
SDCCH, U0
3
MS -> SS
CM SERVICE REQUEST
U0.1
4
SS -> MS
CIPHERING MODE COMMAND
5
MS -> SS
CIPHERING MODE COMPLETE
6
MS -> SS
SETUP
U1
7
SS -> MS
CALL PROCEEDING
U3
8
SS -> MS
ALERTING
U4
9
SS -> MS
ASSIGNMENT COMMAND
TCH
10
MS -> SS
ASSIGNMENT COMPLETE
11
SS -> MS
CONNECT
12
MS -> SS
CONNECT ACKNOWLEDGE
U10
A13
SS -> MS
DISCONNECT
U12 (note 1)
B13
SS -> MS
DISCONNECT
U12 (note 2)
B14
MS -> SS
RELEASE
U19
C13
MMI action, terminate call
C14
MS -> SS
DISCONNECT
U11
NOTE 1: The Progress Indicator IE with progress description #8 "in band information or appropriate pattern now available" is included.
NOTE 2: The Progress Indication IE is not included.
Table 26.8.1.2/2: Establishment of an outgoing call, procedure 2
Step
Direction
Message
Comments/actions/next state
1
MS -> SS
CHANNEL REQUEST
initiate outgoing call
2
SS -> MS
IMMEDIATE ASSIGNMENT
TCH, U0
3
MS -> SS
CM SERVICE REQUEST
U0.1
4
SS -> MS
CHANNEL MODE MODIFY
(note 1)
5
MS -> SS
CHANNEL MODE MODIFY ACKNOWLEDGE
6
SS -> MS
CIPHERING MODE COMMAND
7
MS -> SS
CIPHERING MODE COMPLETE
8
MS -> SS
SETUP
U1
9
SS -> MS
CALL PROCEEDING
U3
10
SS -> SS
ALERTING
U4
11
SS -> MS
CONNECT
12
MS -> SS
CONNECT ACKNOWLEDGE
U10
A13
SS -> MS
DISCONNECT
U12 (note 2)
B13
SS -> MS
DISCONNECT
U12 (note 3)
B14
MS -> SS
RELEASE
U19
C13
MMI action, terminate call
C14
MS -> SS
DISCONNECT
U11
NOTE 1: Assigned channel is appropriate for the chosen bearer capability (see subclause 26.8.1).
NOTE 2: The Progress Indicator IE with progress description #8 "in band information or appropriate pattern now available' is included.
NOTE 3: The Progress Indicator IE is not included.
Table 26.8.1.2/3: Establishment of an outgoing call, procedure 3
Step
Direction
Message
Comments/actions/next state
1
MS -> SS
CHANNEL REQUEST
initiate outgoing call
2
SS -> MS
IMMEDIATE ASSIGNMENT
SDCCH, U0
3
MS -> SS
CM SERVICE REQUEST
U0.1
4
SS -> MS
CIPHERING MODE COMMAND
5
MS -> SS
CIPHERING MODE COMPLETE
6
MS -> SS
SETUP
U1
7
SS -> MS
AUTHENTICATION REQUEST
8
MS -> SS
AUTHENTICATION RESPONSE
9
SS -> MS
CALL PROCEEDING
U3
10
SS -> MS
ASSIGNMENT COMMAND
TCH
11
MS -> SS
ASSIGNMENT COMPLETE
12
SS -> MS
ALERTING
U4
13
SS -> MS
CONNECT
14
MS -> SS
CONNECT ACKNOWLEDGE
U10
A15
SS -> MS
DISCONNECT
U12 (note 1)
B15
SS -> MS
DISCONNECT
U12 (note 2)
B16
MS -> SS
RELEASE
U19
C15
MMI action, terminate call
C16
MS -> SS
DISCONNECT
U11
NOTE 1: The Progress Indicator IE with progress description #8 "in band information or appropriate pattern now available" is included.
NOTE 2: The Progress indicator IE is not included.
Table 26.8.1.2/4: Establishment of an outgoing call, procedure 4
Step
Direction
Message
Comments
1
MS -> SS
CHANNEL REQUEST
initiate outgoing call
2
SS -> MS
IMMEDIATE ASSIGNMENT
TCH, U0
3
MS -> SS
CM SERVICE REQUEST
U0.1
4
SS -> MS
IDENTITY REQUEST
5
MS -> SS
IDENTITY RESPONSE
6
SS -> MS
CIPHERING MODE COMMAND
7
MS -> SS
CIPHERING MODE COMPLETE
8
MS -> SS
SETUP
U1
9
SS -> MS
CHANNEL MODE MODIFY
(note 1)
10
MS -> SS
CHANNEL MODE MODIFY ACKNOWLEDGE
11
SS -> MS
CALL PROCEEDING
U3
12
SS -> MS
ALERTING
U4
13
SS -> MS
CONNECT
14
MS -> SS
CONNECT ACKNOWLEDGE
U10
A15
SS -> MS
DISCONNECT
U12 (note 2)
B15
SS -> MS
DISCONNECT
U12 (note 3)
B16
MS -> SS
RELEASE
U19
C15
MMI action, terminate call
C16
MS -> SS
DISCONNECT
U11
NOTE 1: Assigned channel is appropriate for the chosen bearer capability (see subclause 26.8.1).
NOTE 2: The Progress Indicator IE with progress description #8 "in band information or appropriate pattern now available" is included.
NOTE 3: The Progress Indicator IE is not included.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1 Outgoing call / U0 null state
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1.1 Outgoing call / U0 null state / MM connection requested
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1.1.1 Definition
|
The call control entity of the Mobile Station requests the MM-sublayer to establish a mobile originating MM-connection. This test is applicable for any equipment supporting at least one mobile originated circuit switched basic service.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1.1.2 Conformance requirement
|
1) Upon initiation of an outgoing basic call by user the MS shall initiate establishment of an MM connection, using as first MM message a CM SERVICE REQUEST message with CM service type "Mobile originating call establishment or packet mode connection establishment".
References
3GPP TS 04.08 / 3GPP TS 24.008 subclauses 5.2.1.1, 4.5.1.1 and 3.3.1.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1.1.3 Test purpose
|
To verify that upon initiation of an outgoing basic call by user the MS initiates establishment of an MM connection, using as first MM message a CM SERVICE REQUEST message with CM service type "Mobile originating call establishment or packet mode connection establishment".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
26.8.1.2.1.1.4 Method of test
|
Specific PICS statements
-
PIXIT statements
-
Initial conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in MM-state "idle, updated" with valid TMSI and CKSN.
Foreseen final state of the MS
U0, null.
Test procedure
An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. When the SS receives CM SERVICE REQUEST, the contents of it shall be checked.
Maximum duration of test
30 s.
Expected sequence
Step
Direction
Message
Comments
1
MS -> SS
CHANNEL REQUEST
initiate outgoing call
2
SS -> MS
IMMEDIATE ASSIGNMENT
TCH
3
MS -> SS
CM SERVICE REQUEST
verify the type of call which is asked for "basic" or "emergency by the MS
4
SS -> MS
CHANNEL RELEASE
5
MS
the MS shall release the main signalling link (DISC/UA)
Specific message contents:
None.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.