hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.2.4.2 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) After approx. 60 s the SS is reconfigured and carrier 3 becomes barred (CBA = 1) in order to give the MS the time to perform cell reselection on carrier 3.
d) The SS is reconfigured and the level of carrier 2 is decreased to 13 dBµVemf() / -100 dBm. (C2 decreases to ‑10 dB).
20.24.3.2.4.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.2.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 (highest C1) within 50 s (Cell Selection).
NOTE 1: 33 s for the MS to read the BCCH of carrier 3 (30 s + 10 %), 10 s for communicating the data between SIM and ME, 5 s for search of a matching LSA on SIM. Total 48 s, allow 50 s.
2) The following response from the SoLSA MS shall be received on carrier 3 within 25 s after the first response on carrier 1 (Reselection, highest LSA Priority (15)).
NOTE 2: 5 s for the running average, 10 s to detect C2 differences, 2,4 s to read BCCH of carrier 1, 1 s to perform RA, 5 s for search of a matching LSA on SIM. Total 23,4 s, allow 25 s.
3) After step c), there shall be response from the SoLSA MS on carrier 2 within 55 s after carrier 3 has been barred (Highest LSA Priority on the SIM (8)).
NOTE 3: 30 s for the MS to read the BCCH of carrier 3, 20 s to reselect carrier 2, 5 s for search of a matching LSA on SIM: total 55 s.
4) After step d), there shall be response from the SoLSA MS on carrier 1 within 25 s after carrier 2 has been reconfigured.
NOTE 4: 5 s for the running average, 10 s to detect C2 differences, 2,4 s to read BCCH of carrier 1, 1 s to perform RA, 5 s for search of a matching LSA on SIM. Total 23,4 s, allow 25 s.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / different location area
|
20.23.3.3.1 Definition
While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode support for SoLSA on the SIM card is enabled (See General Remark 1. of subclause 20.24).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.2 Conformance requirement
|
1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss criterion C2) in the same LA, or a much better cell in another LA of the selected PLMN (using the CRH parameter).
- The SoLSA MS will then reselect a new cell in order to fulfil the process goal.
3GPP TS 03.22, subclause 4.5.
2. A SoLSA MS with SIM indicating LSA subscription shall always try to reselect the cell with highest LSA priority according to the information stored on the SIM. 3GPP TS 03.73, subclause 11.4.2.
3. The LSA identification shall be stored on the SIM card in the LSA descriptor files (EF).
LSAs can be described in four different ways (see 3GPP TS 11.11, subclause 10.4.1.3):
- as a list of LSA IDs (3 bytes);
- as a list of LAC + CIs (4 bytes);
- as a list of CIs (2 bytes);
- as a list of LACs (2 bytes); or
- as a combination of the lists above.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.3 Test purpose
|
To verify that the SoLSA MS when idle mode support for SoLSA on the SIM card is enabled shall favour camping on those LSA cells with the highest C2 among those cells with the highest LSA priority the SoLSA MS is subscribed to even if the cell belongs to a different location area.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.4.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/ ‑70
33/ ‑80
33 / -80
13 / -100
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
-90
-90
-90
CRH (dB)
10
10
C1
20
10
10
-10
C2
20
10
10
-10
C4
20
10
10
-10
LSA ID
54
54
54
30.000
LAC
5
5
3
3
CI
5000
5001
5002
5003
c) Further initial conditions (Carrier 1-3 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA1
LSA1
LSA5
Escape PLMN
No
No
No
No
d) Further initial conditions (Carrier 1-3 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA1
LSA1
LSA5
Escape PLMN
Yes
Yes
Yes
Yes
e) Identification of the LSA by means of:
- LSA ID on Carrier 1;
- LAC + CI on Carrier 2;
- LAC on Carrier 3;
- CI on carrier 4.
(see subclause 20.24. General remark 2.)
f) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/ ‑70
33/ ‑80
33 / -80
13 / -100
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
-90
-90
-90
CRH (dB)
10
10
C1
20
10
10
-10
C2
20
10
10
-10
C4
20
10
10
-10
LSA ID
100
250
250
250
LAC
3
3
10
5
CI
5000
500
5002
256
g) Further initial conditions (Carrier 1-4 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA7
LSA7
LSA7
LSA5
Escape PLMN
No
No
No
No
h) Further initial conditions (Carrier 1-4 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA7
LSA7
LSA7
LSA5
Escape PLMN
Yes
Yes
Yes
Yes
Run the following test procedure twice by using four different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d);
- using initial conditions e), f) and g);
- using initial conditions e), f) and h).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.4.2 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 3 is increased to 63 dBV emf() / -50 dBm (C2 increases to 40 dB).
d) The SS is reconfigured and the level of carrier 2 is increased to 63 dBV emf() / -50 dBm (C2 increases to 40 dB).
e) The SS is reconfigured and carrier 3 becomes barred (CBA = 1).
f) The SS activates carrier 4 and monitors carriers 1, 2 and 4. Carrier 3 is switched off.
g) The SS is reconfigured and the level of carrier 4 is increased to 33 dBV emf () / -80 dBm (C2 increases to 10 dB).
20.24.3.3.4.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.3.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. (Cell Selection, highest C1). There shall be no response from the SoLSA MS on any other carrier within 35 s after first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c), there shall be response from the SoLSA MS on carrier 3 within 25 s after increasing the level of carrier 3 (now highest C2 (C2-CRH), for cells with C4 > 0).
3) After step d), there shall be no response from the SoLSA MS on carrier 2 within 35 s after increasing the level of carrier 2 (still highest C2/C2-CRH for carrier 3).
NOTE 2: Any potential access is likely to occur within 25 s.
4) After step e), there shall be response from the SoLSA MS on carrier 2 within 55 s after carrier 3 becomes barred.
5) After step f), there shall be no response from the SoLSA MS on carrier 4 within 60 s after carrier 4 is switched on (Highest LSA Priority (15), but C2 < 0).
6) After step g), there shall be response from the SoLSA MS on carrier 4 within 25 s after increasing level of carrier 4 (not highest C2, but C4 > 0 and highest LSA Priority (15) on the SIM).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4 SoLSA Cell Reselection / idle mode support enabled / Priority Threshold
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.1 Definition
|
While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode support for SoLSA on the SIM card is enabled (see General Remark 1 in subclause 20.24).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.2 Conformance requirement
|
The SoLSA MS shall be able to calculate correctly the signal strength threshold criterion parameter C4 which is to determine whether prioritised LSA cell reselection shall apply.
The signal strength threshold criterion parameter C4 is used to determine whether prioritised LSA cell reselection shall apply and is defined by:
C4 = A - PRIO_THR
Where:
A is defined as above and PRIO_THR is the signal threshold for applying LSA reselection. PRIO_THR is broadcast on the BCCH. If the idle mode support is disabled for the LSA (see 3GPP TS 11.11) or if the cell does not belong to any LSA to which the MS is subscribed or if no PRIO_THR parameter is broadcast, PRIO_THR shall be set to .
3GPP TS 05.08, subclause 6.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3 SoLSA Cell Reselection / idle mode support enabled / Priority Threshold any value
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3.1 Test purpose
|
To verify that the SoLSA MS is able to reselect cells correctly according to parameter PRIO_THR. (parameter C4 criterion).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3.2 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3.2.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2.)
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBµV emf() / dBm)
47 / - 66
55 / ‑58
63 / -50
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
-90
‑90
-90
C1
15
25
40
C2
15
25
40
PRIO_THR
(level / dB)
1 / 6
6 / 36
2 / 12
C4
9
-11
28
LSA ID
66.001
9.000.000
30.000
LAC
5
5
5
CI
5000
5001
5002
NOTE: The level of PRIO_THR is evaluated according to 3GPP TS 05.08, clause 9 and table 1.
c) Further initial conditions (Carrier 1-3 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA3
LSA5
Escape PLMN
No
No
No
d) Further initial conditions (Carrier 1-3 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA3
LSA5
Escape PLMN
Yes
Yes
Yes
Run the following test procedure twice by using two different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3.2.2 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) Carrier 3 is barred (CBA = 1).
d) The PRIO_THR value of carrier 2 is set to 0 dB (level 0).
e) The PRIO_THR value of carrier 2 is set to 36 dB (level 6).
20.24.3.4.3.2.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.3.2.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s after switch on.
2) After step c), the SoLSA MS shall respond on carrier 1 within 55 s after barring of carrier 3 (Highest Priority + C4 > 0).
3) After step d), the SoLSA MS shall respond on carrier 2 within 55 s after changing the PRIO_THR value of carrier 2 (C4 > 0 + Highest C2+LSA_OFFSET).
4) After step e), the SoLSA MS shall respond on carrier 1 within 55 s after changing the PRIO_THR value of carrier 2 (C4 > 0, Highest priority).
20.24.3.4.4 SoLSA Cell Reselection / idle mode support enabled / Priority
Threshold infinite
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.4.1 Test purpose
|
To verify that the SoLSA MS is able to reselect cells correctly according to parameter C2 among those cell not fulfilling C4 0.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.4.2 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.4.2.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
63 / -50
53 / -60
58 / -55
31 / -82
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
-90
-90
-90
-90
CRH (dB)
10
PRIO_THR (level / dB)
7 / 'infinite'
7 / 'infinite'
7 / 'infinite'
C1
40
30
35
8
C2
40
30
35
8
C4
<0
<0
<0
8
LSA_OFFSET (level / dB)
5 / 32
LSA ID
66.001
66.001
9.000.000
30.000
LAC
5
5
3
3
CI
5000
5001
5002
5003
c) Further initial conditions (Carrier 1-4 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA1
LSA3
LSA5
Escape PLMN
No
No
No
No
d) Further initial conditions (Carrier 1-4 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA1
LSA1
LSA3
LSA5
Escape PLMN
Yes
Yes
Yes
Yes
Run the following test procedure twice by using two different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.4.2.2 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 1 is decreased to 33 dBµV emf() / -80 dBm (C2 of carrier 1 becomes 10).
d) The SS is reconfigured and the level of carrier 3 is increased to 63 dBµV emf() / -50 dBm (C2 of carrier 3 becomes 40).
e) Carrier 1 is switched off. Carrier 4 is switched on. The SS monitors carriers 2, 3 and 4.
20.24.3.4.4.2.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.4.4.2.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 25 s after carrier 1 has been reconfigured (Highest C2/C2-CRH).
3) After step d), there shall be response on carrier 3 within 25 s after carrier 2 has been reconfigured (Highest C2/C2-CRH).
4) After step e), there shall be response on carrier 4 within 60 s after the system has been reconfigured (idle mode support enabled for carrier 4).
NOTE: 5,5 s to notice new strongest carriers on top 6 (because the updating time for the 6 strongest is 5 s (±10%)), 33 s to read BCCH, 15 s for reselection, 5 s for search of a matching LSA on SIM. Allow 60 s.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / LSA_OFFSET
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.1 Definition
|
While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.2 Conformance requirement
|
While performing cell reselection, the SoLSA MS shall be able to calculate correctly the signal strength threshold criterion parameter consisting of C2 + LSA_OFFSET to determine which LSA cell shall be selected among those having the same LSA priority; 3GPP TS 05.08, subclause 6.6.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.3 Test Purpose
|
To verify that the SoLSA MS shall be able to reselect the cell with the highest value of C2 + LSA_OFFSET among those cells that have highest LSA priority and fulfil the criteria C4 0.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.4.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBµV emf() / dBm)
63 / ‑50
43 / ‑70
33 / ‑80
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
40
20
10
C2
40
20
10
C4
40
20
10
LSA_OFFSET (level / dB)
0 / 0
1 / 4
4 / 24
LSA ID
30.000
66.001
66.001
LAC
5
5
5
CI
5000
5001
5002
NOTE: The level of LSA_OFFSET is evaluated according to 3GPP TS 05.08, clause 9 and table 1.
c) Further initial conditions (Carrier 1-3 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA5
LSA1
LSA1
Escape PLMN
No
No
No
d) Further initial conditions (Carrier 1-3 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
LSA5
LSA1
LSA1
Escape PLMN
Yes
Yes
Yes
Run the following test procedure twice by using two different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.4.2 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) Carrier 1 is barred (CBA = 1).
d) Carrier 3 is barred (CBA = 1).
20.24.3.5.4.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.5.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 after 50 s. (highest value of C1). There shall be no response from the SoLSA MS on other carriers within 35s after the first response sent on carrier 1.
NOTE: Any potential access is likely to occur within 25 s.
2) After step c), the SoLSA MS shall respond on carrier 3 within 55 s after carrier 1 becomes barred. (same priority as for LSA on carrier 2 but highest value of C2+LSA_OFFSET).
3) After step d), the SoLSA MS shall respond on carrier 2 within 55 s after carrier 3 becomes barred.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6 SoLSA Cell Reselection / idle mode support enabled / LSA Priority / cell combinations
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.1 Definition
|
-
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.2 Conformance requirement
|
1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss criterion C2) in the same LA.
- The MS will then reselect a new cell in order to fulfil the process goal.
3GPP TS 03.22, subclause 4.5.
2. The SoLSA MS shall reselect the correct cell when subscription for normal LSA cells and LSA exclusive access cells varies; GSM 03.73, subclauses 4.3.1 and 4.3.3.
The setting of the LSA only bit on the SIM shall not influence the behaviour of the cell reselection: for subscribers with LSA only access call unrelated service requests are accepted even outside of the allowed LSAs. 3GPP TS 03.73, subclause 4.5.4.
3. When MS is out of the allowed LSA it shall be registered in PLMN but indicate subscriber/service specific "out of LSA area" notification. It shall be a network controlled function to prevent terminated or/and originated calls. Emergency calls are however always allowed. 3GPP TS 02.11, subclause 5.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.3 Test purpose
|
To verify that the SoLSA MS shall reselect the correct cell when subscription for normal LSA cells and LSA exclusive access cells varies. The setting of LSA only bit on the SIM shall not influence the behaviour of the cell reselection.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4 Method of tests
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.1 Initial conditions
|
a) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
53/ ‑60
43/ ‑70
63 / ‑50
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
30
20
40
C2
30
20
40
C4
30
20
<0
b) Further parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
LSA ID
9.000.000
30.000
250
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
LSA3
LSA5
-
Escape PLMN
Yes
No
No
c) Further parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
LSA ID
250
9.000.000
250
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
-
LSA3
-
Escape PLMN
No
Yes
No
d) Further parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
LSA ID
250
30.000
250
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
-
LSA5
-
Escape PLMN
No
No
Yes
e) Further parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
LSA ID
250
250
250
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
-
-
-
Escape PLMN
Yes
No
No
f) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
Run the following test procedures twice using two different sets of initial conditions:
- with an LSA only SIM;
- with a normal LSA SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.2.1 Test Procedure
|
Using conditions from table a), b) and f).
a) The SS activates the carriers 1, 2, 3 and monitors these carriers for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and carrier 3 becomes barred (CBA = 1).
d) The SS is reconfigured and carrier 2 becomes barred (CBA = 1) and carrier 3 becomes not barred (CBA = 0).
20.24.3.6.4.2.2 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.2.3 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 3.
NOTE 1: Any potential access is likely to occur within 35 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 60 s after activating of carriers 2 and 3. (Highest LSA Priority on the SIM (15) for C4 0 in the present subscription).
NOTE 2: 5,5 s to notice new strongest carriers on top 6 (because the updating time for the 6 strongest is 5 s (±10%)), 33 s to read BCCH, 15 s for reselection, 5 s for search of a matching LSA on SIM. Allow 60 s.
3) After step d), there shall be response from SoLSA MS on carrier 1 within 55 s after carrier 2 has become barred (highest priority (8) with C4 0).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.3.1 Test Procedure
|
Using conditions from table a), c) and f).
a) The SS activates carrier 1 and monitors that carrier for RA requests from the SoLSA MS.
Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) The SS activates the carriers 2 and 3 (carrier 1 is still switched on) and monitors carriers 1, 2 and 3 for RA requests from the SoLSA MS.
d) The SS is reconfigured and the carrier 2 becomes barred (CBA = 1).
20.24.3.6.4.3.2 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.3.3 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 after 60 s (highest LSA Priority on the SIM (8) with C4 0).
3) After step d), there shall be response from SoLSA MS on carrier 3 within 55 s after carrier 2 becomes barred (no subscription, Highest C2).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.4.1 Test Procedure
|
Using conditions from table a), d) and f).
a) The SS activates the carrier 1 and monitors that carrier for RA requests from the SoLSA MS. Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) The SS activates the carriers 2 and 3 (carrier 1 is still switched on) and monitors carriers 1, 2 and 3 for RA requests from the SoLSA MS.
d) The SS is reconfigured and carrier 2 becomes barred (CBA = 1).
20.24.3.6.4.4.2 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.4.3 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 after 60 s after carrier 2 and 3 were switched on (LSA with highest Priority (15)).
3) After step d), there shall be response from SoLSA MS on carrier 1 within 55 s after carrier 2 has become barred (Carrier 3 is an LSA exclusive access cell with no matching subscription).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.5.1 Test Procedure
|
Using conditions from table a),e) and f).
a) The SS activates carriers 1 and 3 and monitors these for RA requests from the SoLSA MS.
b) The SoLSA MS is switched on.
c) The SS activates carrier 2 and carrier 3 becomes barred. (CBA = 1).
d) The SS is reconfigured and carrier 2 becomes barred. (CBA = 1).
20.24.3.6.4.5.2 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.6.4.5.3 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 3 within 50 s (Carrier 1 is an LSA exclusive access cell with no matching subscription).
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 55 s.
3) After step d), there shall be no paging response from SoLSA MS on any carrier (Carrier 2 and 3 are barred, carrier 1 is an exclusive access cell, the SoLSA MS is in the limited state) within 65 s.
NOTE: Any potential access is likely to occur quicker.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7 SoLSA Cell Reselection / roaming
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.1 Definition
|
While camped on a cell of the selected PLMN the SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
Idle mode support for SoLSA on the SIM card is enabled (see General Remark 1. in subclause 20.24).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.2 Conformance requirement
|
1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- There is a better cell (in terms of the path loss criterion C2) in the same LA.
- The SoLSA MS will then reselect a new cell in order to fulfil the process goal.
3GPP TS 03.22, subclause 4.5.
2. A SoLSA MS with SIM indicating LSA subscription shall always try to reselect the cell with highest LSA priority according to the information stored on the SIM. 3GPP TS 03.73, subclause 11.4.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.3 Test Purpose
|
To verify that the SoLSA MS when idle mode support for SoLSA on the SIM card is enabled shall favour camping on those LSA cells with the highest LSA priority the SoLSA MS is subscribed to even if subscriber is outside of his HPLMN.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.4.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24 General remark 2.).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
63/-50
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
‑90
MCC, MNC
VPLMN
VPLMN
VPLMN
VPLMN
C1
20
30
10
40
C2
20
30
10
40
C4
20
<0
10
40
LSA ID
9.000.000
-
9.000.001
54
LAC
5
5
5
5
CI
5000
5001
5002
5003
c) Further initial conditions (Carrier 1-3 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
-
-
LSA8
LSA9
Escape PLMN
No
No
No
No
d) Further initial conditions (Carrier 1-3 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Matching LSA on SIM
-
-
LSA8
LSA9
Escape PLMN
Yes
Yes
Yes
Yes
Run the following test procedure twice by using two different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.4.2 Test Procedure
|
a) The SS activates carrier 1 and carrier 2, pages the MS on these carriers and monitors these for RA requests from the SoLSA MS. Carriers 3 and 4 are switched off.
b) The SoLSA MS is switched on.
c) After approx. 60 s the SS is reconfigured and level of carrier 2 decreases to 33 dBµV/-80dBm (C2 decreases to 10). The SS monitors carriers 1 and 2 for RA requests from the SoLSA MS.
d) The SS activates carriers 3 and 4. The SS pages the MS on carriers 3 and 4, and monitors these carriers for RA requests from the SoLSA MS.
e) The SS is reconfigured and carrier 3 becomes barred (CBA = 1). The SS pages the MS on carrier 4, and monitors this carrier for RA requests from the SoLSA MS.
20.24.3.7.4.3 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.3.7.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 2 within 50 s.
2) After step c), there shall be response from the SoLSA MS on carrier 1 within 25 s after decreasing the level of carrier 2 (highest C2).
3) After step d), there shall be response from the SoLSA MS on carrier 3 within 55 s (highest priority on the SIM card for matching LSA subscription).
4) After step e), there shall be response from the SoLSA MS on carrier 4 within 55 s.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4 SoLSA Cell Reselection / idle mode support / any value
|
General Remark
Definition of "idle mode support" is given in subclause 20.24 General Remark 1.
"Idle mode support" is only controlling if 'favouring' shall be done at cell reselection. It does not disable the LSA subscription.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.1 Definition
|
While camped on a cell of the selected PLMN a SoLSA MS may need to select a different cell in order to fulfil the normal service state. This ensures that the SoLSA MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.2 Conformance requirement
|
1. While camped on a cell of the selected PLMN ("camped normally"), the SoLSA MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
- The cell camped on (current serving cell) has become barred.
- There is a better cell (in terms of the path loss criterion C2) in the same LA, or a much better cell in another LA of the selected PLMN (using the CRH parameter).
- The SoLSA MS will then reselect a new cell in order to fulfil the process goal.
3GPP TS 03.22, subclause 4.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.3 Test purpose
|
To verify that the SoLSA MS shall not favour camping on the LSA for which support in idle mode is disabled.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.5 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
63/ ‑50
53/-60
58/-55
31 / -82
CBA
0
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
-90
-90
-90
CRH (dB)
10
C1
40
30
35
8
C2
40
30
35
8
C4
40
30
35
8
LSA ID
66.000
66.000
9.000.001
5
LAC
5
5
3
3
CI
5000
5001
5002
5003
c) Further initial conditions (Carrier 1-4 are normal LSA cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Idle mode support enabled
No
No
No
Yes
Matching LSA on SIM
LSA2
LSA2
LSA4
LSA6
Escape PLMN
No
No
No
No
d) Further initial conditions (Carrier 1-4 are LSA exclusive access cells).
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Idle mode support enabled
No
No
No
Yes
Matching LSA on SIM
LSA2
LSA2
LSA4
LSA6
Escape PLMN
Yes
Yes
Yes
Yes
Run the following test procedure twice by using two different sets of initial conditions:
- using initial conditions a), b) and c);
- using initial conditions a), b) and d).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.6 Test Procedure
|
a) The SS activates carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS. Carrier 4 is switched off.
b) The SoLSA MS is switched on.
c) The SS is reconfigured and the level of carrier 1 is decreased to 33 dBµV emf() / -80 dBm (C2 of carrier 1 becomes 10).
d) The SS is reconfigured and the level of carrier 3 is increased to 63 dBµV emf() / -50 dBm (C2 of carrier 3 becomes 40).
e) Carrier 1 is switched off. Carrier 4 is switched on. The SS monitors carriers 2, 3 and 4.
20.24.4.7 void
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.4.8 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no response from the SoLSA MS on any other carrier within 35 s after the first response on carrier 1.
NOTE 1: Any potential access is likely to occur within 25 s.
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 25 s after carrier 1 has been reconfigured (Highest C2/C2-CRH).
3) After step d), there shall be response on carrier 3 within 25 s after carrier 3 has been reconfigured (Highest C2/C2-CRH).
4) After step e), there shall be response on carrier 4 within 60 s after the system has been reconfigured (idle mode support enabled for carrier 4).
NOTE 2: 5,5 s to notice new strongest carriers on top 6 (because the updating time for the 6 strongest is 5 s (±10%)), 33 s to read BCCH, 15 s for reselection, 5 s for search of a matching LSA on SIM. Allow 60 s.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5 SoLSA Cell Reselection / LSA indication for idle mode
|
General Remark
Definition of "LSA indication for idle mode" is given in subclause 20.24 General Remark 1.
"LSA indication for idle mode" is only controlling if indication of the LSA name shall be done. It has no influence on the LSA subscription.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.1 General Definition
|
The SoLSA MS in idle mode may inform the user whether or not the serving cell belongs to the subscribed LSA.
- The indication is dependent on the setting of the idle mode indication bit on the SIM card for that LSA.
- The indication is independent from the setting of the LSA idle mode support bit on the SIM card for that LSA (see subclause 20.24 General Remark 1).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.2 General conformance requirement
|
1. The service subscriber can define a name (alphanumeric name, icon, etc) for each of her allowed LSAs. The MS will, in idle mode and if required by the user, indicate to the user the current LSA. The indication may be the name of the current LSA, as set by the user. The form of display and indication are left to manufacturer's choice. 3GPP TS 03.73, subclause 4.3.2.
2. In addition to indicate the registered PLMN, an MS with subscription for an LSA in the registered PLMN shall indicate this LSA when it is available. The indication towards the user is optional and may be done by displaying the stored LSA name that corresponds to the ID of the current LSA. An MS with LSA only access subscription may also give an indication towards the user, when the no subscribed LSAs are available to the user. The indication is optional and may be done by displaying the LSA only access text stored in the SIM. 3GPP TS 03.73, subclause 11.8.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3 SoLSA Cell Reselection / LSA indication for idle mode / idle mode support enabled
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.1 Definition
|
See general Definition of this subclause.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.2 Conformance requirement
|
1. When both idle mode support and idle mode indication are enabled on the SIM card, the SoLSA MS shall display the name (which was defined by the service subscriber) of the current LSA to the user.
2. When idle mode support is enabled and idle mode indication is disabled on the SIM card, it is expected that the SoLSA MS does not display the LSA name (which was defined by the service subscriber) of the current LSA to the user.
3GPP TS 03.73, subclause 4.3.2; 3GPP TS 03.73, subclause 11.8.1; 3GPP TS 11.11, subclause 10.4.1.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.3 Test Purpose
|
1. To verify that if idle mode indication bit on the SIM card is enabled for the LSA, the SoLSA MS supports the LSA indication. The LSA name (text/icon) shall be displayed on the SoLSA MS.
2. To verify that if idle mode indication bit on the SIM card is disabled for the LSA the SoLSA MS does not support the LSA indication.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.4.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
OFF
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
20
30
10
C2
20
30
10
LSA ID
-
66.001
9.000.000
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
-
LSA1
LSA3
Escape PLMN
No
No
No
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.4.2 Test Procedure
|
a) The SS activates carrier 1, pages the MS on this carrier and monitors it for RA requests from the SoLSA MS. Carrier 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) Carrier 2 and Carrier 3 are switched on. The SS pages the MS on carriers 1, 2 and 3, and monitors these carriers for RA requests from the SoLSA MS.
d) The SS is reconfigured and carrier 3 becomes barred (CBA = 1). The SS pages the MS on carriers 1, 2 and 3, and monitors these carriers for RA requests from the SoLSA MS.
e) The SS is reconfigured and sets CBA = 0 on carrier 3. The SS pages the MS on carriers 1, 2 and 3 and monitors these carriers for RA requests from the SoLSA MS.
20.24.5.3.4.3a Specific PICS statements
-20.24.5.3.4.3b PIXIT statements
- Interface to the human user (p1=Y/N).
- Way to indicate the identity of the current LSA to the human user (only applicable if the SoLSA MS has an interface to the human user).
- Way to indicate the change of the current LSA to the human user (only applicable if the SoLSA MS has an interface to the human user).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.3.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no LSA indication on the SoLSA MS (No LSA).
2) After step c), there shall be response from the SoLSA MS on carrier 3 within 25 s (highest LSA Priority (8) on the SIM card). An LSA indication is expected on the SoLSA MS.
3) After step d), there shall be response from the SoLSA MS on carrier 2 within 55 s. There shall be no indication on the SoLSA MS (highest LSA Priority on the SIM card, no indication on the SIM card).
4) After step e), there shall be response from the SoLSA MS on carrier 3 within 55 s (LSA carrier on the SIM card). An LSA indication is expected on the SoLSA MS (idle mode indication for that LSA is enabled).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4 SoLSA Cell Reselection / LSA indication for idle mode / idle mode support disabled
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.1 Definition
|
See general Definition of this subclause.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.2 Conformance requirement
|
1. When idle mode support is disabled and idle mode indication is enabled on the SIM card, it is expected that the SoLSA MS displays the LSA name (which was defined by the service subscriber) of the current LSA to the user.
2. When idle mode support is disabled and idle mode indication is disabled on the SIM card, the SoLSA MS shall not display the LSA name (which was defined by the service subscriber) of the current LSA to the user.
3GPP TS 03.73, subclause 4.3.2; 3GPP TS 03.73, subclause 11.8.1; 3GPP TS 11.11, 1subclause 0.4.1.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.3 Test Purpose
|
To verify that when idle mode support is disabled, the SoLSA MS shall display the LSA name in dependence from the idle mode indication bit.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.4.1 Initial conditions
|
a) Identification of the LSA by means of LSA ID (see subclause 20.24. General remark 2).
b) Parameters changed from the default values in table 20.24.1; further initial conditions.
Parameter/condition
Carrier 1
Carrier 2
Carrier 3
Carrier 4
RF Signal Level
(dBV emf() / dBm)
43/-70
53/-60
33/-80
OFF
CBA
0
0
0
RXLEV_ACCESS_MIN (dBm)
‑90
‑90
‑90
C1
20
30
10
C2
20
30
10
LSA ID
250
66.000
9.000.001
LAC
5
5
5
CI
5000
5001
5002
Matching LSA on SIM
-
LSA2
LSA4
Escape PLMN
No
No
No
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.4.2 Test Procedure
|
a) The SS activates carrier 1, pages this carrier and monitors it for RA requests from the SoLSA MS. Carriers 2 and 3 are switched off.
b) The SoLSA MS is switched on.
c) Carrier 2 and carrier 3 are switched on. The SS pages the MS on carriers 1, 2 and 3, and monitors these carriers for RA requests from the SoLSA MS.
d) The SS is reconfigured and the level of carrier 3 increases to 63 dBµVemf / -50dBm (C2 increases to 40 dB).
e) The SS is reconfigured and the level of carrier 3 decreases to 33 dBµVemf0,1,0 /- 80dBm (C2 decreases to 10 dB).
20.24.5.4.4.3a Specific PICS statements
-
20.24.5.4.4.3b PIXIT statements
- Interface to the human user (p1=Y/N).
- Way to indicate the identity of the current LSA to the human user (only applicable if the SoLSA MS has an interface to the human user).
- Way to indicate the change of the current LSA to the human user (only applicable if the SoLSA MS has an interface to the human user).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.24.5.4.4.4 Test Requirements
|
1) After step b), the first response from the SoLSA MS shall be received on carrier 1 within 50 s. There shall be no LSA indication on the SoLSA MS.
2) After step c), there shall be response from the SoLSA MS on carrier 2 within 25 s (highest C2). An LSA indication is expected on the SoLSA MS.
3) After step d), there shall be response from the SoLSA MS on carrier 3 within 25 s (highest C2). There shall be no LSA indication on the SoLSA MS.
4) After step e), there shall be response from the SoLSA MS on carrier 2 within 25 s (highest C2). An LSA indication is expected on the SoLSA MS.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25 Intersystem Cell Reselection
|
The default parameters for the GSM/GPRS cell, the accuracy of the MS signal measurements and tolerance of timers, are given in TS 51.010 section 20.22.
The default parameters and tolerances of the UTRAN cells are specified in TS 34.108.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.1 Definition of system information messages
|
SYSTEM INFORMATION TYPE 3 REST OCTETS
• SI2q indicated on BCCH Norm
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
< RR management Protocol Discriminator bit (4) >
‘0110'B
< Skip Indicator : bit (4) >
‘0000'B
< Message type : bit (8) >
‘0000 0111’B
< SI2 quarter Rest Octets >
< BA_IND : bit >
0
< 3G_BA_IND : bit >
0
< MP_CHANGE_MARK : bit >
0
< SI2quater _INDEX : bit (4) >
‘0000’B
< SI2quater_COUNT : bit (4) >
‘0000’B
0 | 1 < Measurement_Parameters Description >
0
0 | 1 < GPRS_Real Time Difference Description >
0
0 | 1 < GPSR_BSIC Description >
0
0 | 1 < GPRS_REPORT PRIORITY Description >
0
0 | 1 < GPRS_Measurement_Parameters Description >
0
0 | 1 < NC Measurement Parameters >
0
0 | 1 < extension length >
0
0 | 1 < 3G Neighbour Cell Description >
1
0 | 1 < Index_Start_3G : bit (7) >
0
0 | 1 < Absolute_Index_Start_EMR : bit (7) >
0
0 | 1 < UTRAN FDD Description >
1
0 | 1 < Bandwidth_FDD : bit (3) >
0
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
1
0 < FDD-ARFCN : bit (14) >
0 See TS 34.108, clause 6.1.5, table 6.1.1
< FDD_Indic0 : bit >
0
< NR_OF_FDD_CELLS : bit (5) >
‘00001’B
< FDD_CELL_INFORMATION Field >
10 bits
Scrambling code according to TS 34.108, clause 6.1.4, Default settings for cell No.1
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
0
0 | 1 < UTRAN TDD Description >
0
0 | 1 < 3G MEASUREMENT Parameters Description >
1
< Qsearch_I : bit (4) >
‘0111’B (Always)
< Qsearch_C_Initial : bit (1) >
0
0 | 1 < FDD_Qoffset : bit (4) >
1 ‘0000’B (Always select a cell if acceptable)
< FDD_REP_QUANT : bit (1) >
0
< FDD_MULTIRAT_REPORTING : bit (2) >
‘01’B
< FDD_Qmin : bit (3) >
’111’B (-12 dB)
0 | 1 < TDD_Qoffset : bit (4) >
0
0 | 1 < GPRS_3G_MEASUREMENT Parameters Description >
1
< Qsearch_P : bit (4) >
‘0111’B (Always)
< 3G_SEARCH_PRIO : bit >
0
0 | 1 < FDD_REP_QUANT : bit >
0
0 | 1 < FDD_REPORTING_OFFSET : bit (3) >
0
0 | 1 < TDD_MULTIRAT_REPORTING : bit (2) >
0
0 | 1 < TDD_REPORTING_OFFSET : bit (3) >
0
SYSTEM INFORMATION TYPE 2QUATER Instance 1
Information Element
Value/remark
< RR management Protocol Discriminator bit (4) >
‘0110'B
< Skip Indicator : bit (4) >
‘0000'B
< Message type : bit (8) >
‘0000 0111’B
< SI2 quarter Rest Octets >
< BA_IND : bit >
0
< 3G_BA_IND : bit >
0
< MP_CHANGE_MARK : bit >
0
< SI2quater _INDEX : bit (4) >
‘0000’B
< SI2quater_COUNT : bit (4) >
‘0001’B
0 | 1 < Measurement_Parameters Description >
0
0 | 1 < GPRS_Real Time Difference Description >
0
0 | 1 < GPSR_BSIC Description >
0
0 | 1 < GPRS_REPORT PRIORITY Description >
0
0 | 1 < GPRS_Measurement_Parameters Description >
0
0 | 1 < NC Measurement Parameters >
0
0 | 1 < extension length >
0
0 | 1 < 3G Neighbour Cell Description >
1
0 | 1 < Index_Start_3G : bit (7) >
0
0 | 1 < Absolute_Index_Start_EMR : bit (7) >
0
0 | 1 < UTRAN FDD Description >
1
0 | 1 < Bandwidth_FDD : bit (3) >
0
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
1
0 < FDD-ARFCN : bit (14) >
0 See TS 34.108, clause 6.1.5, table 6.1.1
< FDD_Indic0 : bit >
0
< NR_OF_FDD_CELLS : bit (5) >
‘00001’B
< FDD_CELL_INFORMATION Field >
10 bits
Scrambling code according to TS 34.108, clause 6.1.4, Default settings for cell No.1
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
0
0 | 1 < UTRAN TDD Description >
0
0 | 1 < 3G MEASUREMENT Parameters Description >
1
< Qsearch_I : bit (4) >
‘0111’B (Always)
< Qsearch_C_Initial : bit (1) >
0
0 | 1 < FDD_Qoffset : bit (4) >
1 ‘0000’B (Always select a cell if acceptable)
< FDD_REP_QUANT : bit (1) >
0
< FDD_MULTIRAT_REPORTING : bit (2) >
‘01’B
< FDD_Qmin : bit (3) >
’111’B (-12 dB)
0 | 1 < TDD_Qoffset : bit (4) >
0
0 | 1 < GPRS_3G_MEASUREMENT Parameters Description >
1
< Qsearch_P : bit (4) >
‘0111’B (Always)
< 3G_SEARCH_PRIO : bit >
0
0 | 1 < FDD_REP_QUANT : bit >
0
0 | 1 < FDD_REPORTING_OFFSET : bit (3) >
0
0 | 1 < TDD_MULTIRAT_REPORTING : bit (2) >
0
0 | 1 < TDD_REPORTING_OFFSET : bit (3) >
0
0 | 1 < 3G Additional Measurement Parameters Description >
1
0 | 1 < FDD_REPORTING_OFFSET : bit (3) >
’000’B (0 dB)
0 | 1 < FDD_RSCPmin : bit (4) >
’0000’B (-114 dBm)
0 | 1 <Additions in Rel-6
0
0 | 1 <Additions in Rel-7
0
0 | 1 <Additions in Rel-8
1
0 | 1 <Additions in Rel-8
1
0 | 1 < Priority and E-UTRAN Parameters Description >
1
0 | 1 < Serving Cell Priority Parameters Description >
1
< GERAN_PRIORITY : bit(3) >
‘011’
< THRESH_Priority_Search : bit(4) >
‘1111’ (Always)
< THRESH_GSM_low : bit(4) >
‘1110’ ( 28dB )
< H_PRIO : bit(2) >
‘00’ (rule disabled)
< T_Reselection : bit(2) >;
‘00’ (5 sec)
0 | 1 < 3G Priority Parameters Description >
1
< UTRAN_Start : bit >
1
< UTRAN_Stop : bit >
0
1 < DEFAULT_UTRAN_PRIORITY : bit(3)
5
DEFAULT_THRESH_UTRAN: bit(5)
’01010’B ( 20dB )
DEFAULT_UTRAN_QRXLEVMIN: bit(5) >
’00000’B (-119 dBm)
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
0
0 | 1 < E-UTRAN Parameters Description >
0
0 | 1 < 3G CSG Description >
0
0 | 1 < E-UTRAN CSG Description >
0
SYSTEM INFORMATION TYPE 2QUATER Instance 2
Information Element
Value/remark
< RR management Protocol Discriminator bit (4) >
‘0110'B
< Skip Indicator : bit (4) >
‘0000'B
< Message type : bit (8) >
‘0000 0111’B
< SI2 quarter Rest Octets >
< BA_IND : bit >
0
< 3G_BA_IND : bit >
0
< MP_CHANGE_MARK : bit >
0
< SI2quater _INDEX : bit (4) >
‘0001’B
< SI2quater_COUNT : bit (4) >
‘0001’B
0 | 1 < Measurement_Parameters Description >
0
0 | 1 < GPRS_Real Time Difference Description >
0
0 | 1 < GPSR_BSIC Description >
0
0 | 1 < GPRS_REPORT PRIORITY Description >
0
0 | 1 < GPRS_Measurement_Parameters Description >
0
0 | 1 < NC Measurement Parameters >
0
0 | 1 < extension length >
0
0 | 1 < 3G Neighbour Cell Description >
0
0 | 1 < 3G MEASUREMENT Parameters Description >
0
0 | 1 < GPRS_3G_MEASUREMENT Parameters Description >
0
0 | 1 <Additions in Rel-5
0
0 | 1 <Additions in Rel-6
0
0 | 1 <Additions in Rel-7
0
0 | 1 <Additions in Rel-8
1
0 | 1 < Priority and E-UTRAN Parameters Description >
1
0 | 1 < Serving Cell Priority Parameters Description >
0
0 | 1 < 3G Priority Parameters Description >
1
< UTRAN_Start : bit >
0
< UTRAN_Stop : bit >
1
{ 0 | 1 < DEFAULT_UTRAN_PRIORITY : bit(3) >
0
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
1
1 < UTRAN_FREQUENCY_INDEX > ** 0
1
< UTRAN_FREQUENCY_INDEX : bit (5) >
’0000’B
1 < UTRAN_FREQUENCY_INDEX > ** 0
0
0 | 1 < UTRAN_PRIORITY : bit(3) >
’101’B
< THRESH_UTRAN_high : bit(5) >
’01111’B ( 30dB )
0 | 1 < THRESH_UTRAN_low : bit(5) >
0 ( Default value )
0 | 1 < UTRAN_QRXLEVMIN : bit(5) >
’00010’B (-115 dBm)
1 < Repeated UTRAN FDD Neighbour Cells > ** 0
0
0 | 1 < E-UTRAN Parameters Description >
0
0 | 1 < 3G CSG Description >
0
0 | 1 < E-UTRAN CSG Description >
0
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.2 Intersystem Cell Reselection/Idle Mode/FDD_Qmin
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.2.1 Conformance requirement
|
If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
The MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of RLA_C for the serving cell and all of the suitable (see 3GPP TS 03.22) non-serving GSM cells by the value XXX_Qoffset for a period of 5 seconds and, for FDD, the UTRAN cells measured Ec/No value is equal or greater than the value FDD_Qmin. In case of a cell reselection occurring within the previous 15 seconds, XXX_Qoffset is increased by 5 dB.
Table 1: Radio sub‑system link control parameters
Parameter name
Description
Range
Bits
Channel
FDD_Qmin
A minimum threshold for Ec/No for UTRAN FDD cell re-selection,
0= -20dB, 1= -6dB, 2= -18dB, 3= -8dB, 4= -16dB, 5= -10dB, 6= -14dB, 7= -12dB.
Default value= -12dB.
0-7
3
BCCH D/L
References:
3GPP TS 05.08, subclause 6.6.5 and 9
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.2.2 Test purpose
|
To verify that the MS uses the FDD_Qmin parameter at cell re-selection from GSM to UTRAN while in GSM Idle Mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.2.3 Method of test
|
Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50
Off to -48
Ec/No (dB)
-
-6>dB>-16
NOTE 1: MS is IMSI updated on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, GPRS not present.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4, Default settings for cell No.1
NOTE 4: Serving Cell Parameters are coded and transmitted on the specified Channel Type
NOTE 5: Carriers should have a relative accuracy of ±2 dB.
NOTE 6: When executing the test in FDD band II or FDD band VIII carrier 2 shall use the high range UARFCN, defined in TS 3GPP 34.108 clause 5.1.1. This is to avoid the FDD band overlapping with the GSM band under test.
SYSTEM INFORMATION TYPE 3 REST OCTETS
• GPRS not indicated
SYSTEM INFORMATION TYPE 4 REST OCTETS
• GPRS not indicated
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
< MP_CHANGE_MARK : bit (1)>
0
< FDD_Qmin : bit (3) >
’001’B (-6 dB)
Test procedure
The MS is camping on the GSM cell and has received a 3G Neighbour Cell list is in the 3G_NEIGHBOUR CELL description in System Information Type 2quater. The FDD_Qmin in the 3G_MEASUREMENT_PARAMETERS description is set to –6 dB.
It is verified for 30 sec that no Cell Reselection to the UTRAN cell is performed.
System Information 2quater is updated with FDD_Qmin in the 3G_MEASUREMENT_PARAMETERS description set to -16 dB.
It is verified that a Cell Reselection to UTRAN is performed within 45 secs when UE receives and acts on revised SI2quater and the UTRAN cell Ec/No gets greater than FDD_Qmin. (45 secs = 30 secs period of SI reading + 5 secs for UE to receive and decode SI2quater +2*5sec, where 5 sec is the maximum time between 2 consecutive UTRAN measurements.)
Maximum duration of the test
2 minutes
Expected sequence
Step
Direction
Message
Comments
1
SS
Carrier 2 is activated with -6>Ec/No>-16 (dB)
2
SS <->MS
Verify that no cell reselection is performed to Carrier 2 for 30 sec.
3
SS
SYSTEM INFORMATION TYPE 2QUATER
See specific contents below.
4
MS -> SS
RRC CONNECTION REQUEST
Verify that the MS reselects to Carrier 2 within 45 secs from Step 3.
Establishment cause shall be “interRAT-CellReselection”
Specific message contents
SYSTEM INFORMATION TYPE 2QUATER in Step 3
Information Element
Value/remark
< MP_CHANGE_MARK : bit (1)>
1
< FDD_Qmin : bit (3) >
’100’B (-16 dB)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.3 Intersystem Cell Reselection/Idle Mode/FDD_Qoffset
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.3.1 Conformance requirement
|
If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
The MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of RLA_C for the serving cell and all of the suitable (see 3GPP TS 03.22) non-serving GSM cells by the value XXX_Qoffset for a period of 5 seconds and, for FDD, the UTRAN cells measured Ec/No value is equal or greater than the value FDD_Qmin. In case of a cell reselection occurring within the previous 15 seconds, XXX_Qoffset is increased by 5 dB.
Table 1: Radio sub‑system link control parameters
Parameter name
Description
Range
Bits
Channel
FDD_Qoffset
Applies an offset to RLA_C for cell re‑selection to access technology/mode FDD
0 = - (always select a cell if acceptable),
1 = -28 dB, 2 = -24 dB, … , 15 = 28 dB.
Default value = 0 dB.
0-15
4
BCCH D/L
Power Spectral Density: The units of Power Spectral Density (PSD) are extensively used in this document. PSD is a function of power versus frequency and when integrated across a given bandwidth, the function represents the mean power in such a bandwidth.
References:
3GPP TS 05.08, subclause 6.6.5 and 9; TS 25.101 subclause 3.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.3.2 Test purpose
|
To verify that the MS uses the FDD_Qoffset parameter at cell re-selection from GSM/GPRS to UTRAN while in Idle Mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.3.3 Method of test
|
Initial conditions
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-75
RXLEV_ACCESS_MIN
dBm
-100
FDD_Qoffset
dB
20
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
CPICH_Ec (FDD)
dBm / 3.84 MHz
OFF to -62 to -48
NOTE 1: MS is IMSI updated on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, GPRS not present.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4, Default settings for cell No.1
NOTE 4: Serving Cell Parameters are coded and transmitted on the specified Channel Type.
NOTE 5: Carriers should have a relative accuracy of ±3 dB.
NOTE 6: When executing the test in FDD band II or FDD band VIII carrier 2 shall use the high range UARFCN, defined in TS 3GPP 34.108 clause 5.1.1. This is to avoid the FDD band overlapping with the GSM band under test.
SYSTEM INFORMATION TYPE 3 REST OCTETS
• SI2q indicated on BCCH extended
• GPRS not indicated
SYSTEM INFORMATION TYPE 4 REST OCTETS
• GPRS not indicated
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
0 | 1 < FDD_Qoffset : bit (4) >
1 ‘1101’B (20 dB)
Test procedure
The MS is camping on the GSM cell and has received a 3G Neighbour Cell list is in the 3G_NEIGHBOUR CELL description in System Information Type 2quater. The FDD_Qoffset in the 3G_MEASUREMENT_PARAMETERS description is set to 20 dB.
It is verified for 30 sec that no Cell Reselection to the UTRAN cell is performed.
The UTRAN cell CPICH Ec is increased to –50 dBm / 3.84 MHz and therefore, The mean power of the CPICH Ec integrated across 3.84 MHz bandwidth is –50dBm
It is verified that a Cell Reselection to UTRAN CPICH Ecis performed within 15.4 sec when the UTRAN cell mean power of the CPICH Ec integrated across 3.84 MHz gets greater than the GSM cell RLA_C + FDD_Qoffset. (15.4 sec = 2*5sec, where 5 sec is the maximum time between 2 consecutive UTRAN measurements, with 4 seconds to read the SIBs plus 10% tolerance overall)
Maximum duration of the test
2 minutes
Expected sequence
Step
Direction
Message
Comments
1
SS
Carrier 2 is activated
2
SS
Verify that the MS does not reselect to Carrier 2 for 30 sec.
3
SS
Increase power of Carrier 2 to –50 dBm.
4
MS -> SS
RRC CONNECTION REQUEST
Verify that the MS reselects to Carrier 2 within 15.4 sec from Step 3.
Establishment cause shall be “interRAT-CellReselection”
Specific message contents
None
20.25.3a Intersystem Cell Reselection/Idle Mode/TDD_Qoffset (1.28Mcps TDD)
20.25.3a.1 Conformance requirement
If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
The MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of TDD_ Qoffset for a period of 5 seconds.
Table 1: Radio sub‑system link control parameters
Parameter name
Description
Range
Bits
Channel
TDD_Qoffset
An absolute threshold of RSCP for UTRAN TDD cell re-selection,
0 = -105dBm, 1 = -102dBm, 2=-99dBm, 3 = -96dBm, 4 = -93dBm, 5 = -90dBm, 6 = -87dBm, 7 = -84dBm, 8 = -81dBm, 9 = -78dBm, 10 = -75dBm, 11 = -72dBm, 12 = -69dBm, 13 = -66dBm, 14 = -63dBm, 15 = -60dBm.
Default value = -90dBm.
0-15
4
BCCH D/L
References:
3GPP TS 05.08, subclause 6.6.5 and 9; TS 25.101 subclause 3.1.
20.25.3a.2 Test purpose
To verify that the MS uses the TDD_Qoffset parameter at cell re-selection from GSM/GPRS to UTRAN while in Idle Mode.
20.25.3a.3 Method of test
Initial conditions
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-75
RXLEV_ACCESS_MIN
dBm
-100
Qsearch_I
dBm
7 (always)
TDD_Qoffset
dBm
-90
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
PCCPCH RSCP (TDD)
dBm / 1.28 MHz
OFF to -99 to -77
NOTE 1: MS is IMSI updated on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, GPRS not present.
NOTE 3: Carrier 2 is the UTRAN TDD cell configured according to TS 34.108, clause 6.1.4, Default settings for cell No.1
NOTE 4: Serving Cell Parameters are coded and transmitted on the specified Channel Type.
NOTE 5: Carriers should have a relative accuracy of ±3 dB.
SYSTEM INFORMATION TYPE 3 REST OCTETS
- SI2q indicated on BCCH extended
- GPRS not indicated
SYSTEM INFORMATION TYPE 4 REST OCTETS
- GPRS not indicated
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
0 | 1 < TDD_Qoffset : bit (4) >
1 ‘0101’B (-90 dBm)
Test procedure
The MS is camping on the GSM cell and has received a 3G Neighbour Cell list is in the 3G_NEIGHBOUR CELL description in System Information Type 2quater. The TDD_Qoffset in the 3G_MEASUREMENT_PARAMETERS description is set to -90 dBm.
It is verified for 30 sec that no Cell Reselection to the UTRAN cell is performed.
The UTRAN cell PCCPCH RSCP is increased to –77 dBm / 1.28 MHz and therefore, The mean power of the PCCPCH RSCP integrated across 1.28 MHz bandwidth is –77dBm
It is verified that a Cell Reselection to UTRAN is performed within 15.4 sec when the UTRAN cell mean power of the PCCPCH RSCP integrated across 1.28 MHz gets greater than TDD_Qoffset. (15.4 sec = 2*5sec, where 5 sec is the maximum time between 2 consecutive UTRAN measurements, with 4 seconds to read the SIBs plus 10% tolerance overall)
Maximum duration of the test
2 minutes
Expected sequence
Step
Direction
Message
Comments
1
SS
Carrier 2 is activated
2
SS
Verify that the MS does not reselect to Carrier 2 for 30 sec.
3
SS
Increase power of Carrier 2 to –77 dBm.
4
MS -> SS
RRC CONNECTION REQUEST
Verify that the MS reselects to Carrier 2 within 15.4 sec from Step 3.
Establishment cause shall be “interRAT-CellReselection”
Specific message contents
None
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.4 Intersystem Cell Reselection/Idle Mode/Qsearch_I
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.4.1 Conformance requirement
|
If the 3G Cell Reselection list includes UTRAN frequencies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non-serving GSM cells.
For FDD, the MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of RLA_C for the serving cell and all of the suitable (see 3GPP TS 03.22) non-serving GSM cells by the value FDD_Qoffset for a period of 5 seconds and the UTRAN cells measured Ec/No value is equal or greater than the value FDD_Qmin. In case of a cell reselection occurring within the previous 15 seconds, FDD_Qoffset is increased by 5 dB.
For TDD, the MS shall then reselect a suitable (see TS 25.304) UTRAN cell if its measured RSCP value exceeds the value of TDD_ Qoffset for a period of 5 seconds.
Table 1a: Radio sub‑system link control parameters for FDD
Parameter name
Description
Range
Bits
Channel
Qsearch_I
Search for 3G cells if signal level is below (0‑7) or above (8‑15) threshold
0 = - 98 dBm, 1 = - 94 dBm, … ,
6 = - 74 dBm, 7 = (always)
8 = - 78 dBm, 9 = - 74 dBm, … ,
14 = - 54 dBm, 15 = (never).
Default value = (never).
0-15
4
BCCH D/L
Table 1b: Radio sub‑system link control parameters for TDD
Parameter name
Description
Range
Bits
Channel
Qsearch_I
Search for 3G cells if signal level is below (0‑7) or above (8‑15) threshold
0 = - 98 dBm, 1 = - 94 dBm, … ,
6 = - 74 dBm, 7 = (always)
8 = - 90 dBm, 9 = - 86 dBm, … ,
14 = - 66 dBm, 15 = (never).
Default value = (never).
0-15
4
BCCH D/L
References:
3GPP TS 05.08, subclause 6.6.5 and 9
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.4.2 Test purpose
|
To verify that the MS uses the Qsearch_I parameter at cell re-selection from GSM to UTRAN while in Idle Mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.4.3 Method of test
|
Initial conditions
For MS supporting FDD:
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-60 to -77
RXLEV_ACCESS_MIN
dBm
-100
MP_CHANGE_MARK
0
Qsearch_I
15 to 6
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
CPICH_Ec (FDD)
dBm / 3.84 MHz
OFF to -50
For MS supporting TDD:
Parameter
Unit
Cell 1
(GSM)
Test Channel
1
RF Signal Level
dBm
-77 to -71
RXLEV_ACCESS_MIN
dBm
-100
MP_CHANGE_MARK
0
Qsearch_I
15 (never) to 12 (-74dBm)
Parameter
Unit
Cell 2
(UTRAN)
Test Channel
1
PCCPCH_RSCP (TDD)
dBm / 1.28 MHz
OFF to -50
NOTE 1: MS is IMSI attached on Cell 1.
If MS supports GPRS, then MS is GPRS attached on cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, PBCCH not present, NC0.
NOTE 3: Carrier 2 is either the UTRAN FDD cell or the UTRAN TDD cell configured according to TS 34.108, clause 6.1.4, Default settings for cell No.1
NOTE 4: Serving Cell Parameters are coded and transmitted on the specified Channel Type
NOTE 5: Carriers should have a relative accuracy of ±3 dB.
SYSTEM INFORMATION TYPE 2QUATER
Information Element
Value/remark
< Qsearch_I : bit (4) >
‘1111’B (Never)
< Qsearch_P : bit (4) >
‘0111’B (Always)
Specific PICS statements:
• Support of UTRAN FDD (TSPC_Type_UTRAN_FDD)
• Support of UTRAN TDD (TSPC_Type_UTRAN_TDD)
Test procedure
The MS is camping on the GSM cell and has received a 3G Neighbour Cell list is in the 3G_NEIGHBOUR CELL description in System Information Type 2quater. Qsearch_I in the 3G_MEASUREMENT_PARAMETERS description indicates that no 3G measurements shall be performed.
It is verified for 30 sec that no Cell Reselection to the UTRAN cell is performed.
For FDD, the SS broadcast a new System Information Type 2quater with an updated Qsearch_I indicating that 3G measurements shall be performed when the strongest GSM cell RLA_C is below –74 dBm.
For TDD, The SS broadcast a new System Information Type 2quater with an updated Qsearch_I indicating that 3G measurements shall be performed when the strongest GSM cell RLA_C is above –74 dBm.
It is verified for 65 sec that no Cell Reselection to the UTRAN cell is performed. (Maximum 30 sec for SI reading + 5 sec for System Information 2quater reading + 30 sec to find the UTRAN.)
For FDD, the GSM cell RLA_C is decreased to –77 dBm.
For TDD, the GSM cell RLA_C is increased to –71 dBm.
It is verified that a Cell Reselection to UTRAN is performed within 30 sec.
Maximum duration of the test
4 minutes
Expected sequence
This sequence is performed for each UTRAN mode the MS supports.
Step
Direction
Message
Comments
1
SS
Carrier 2 is activated on –50 dBm
2
SS
Verify that no cell reselection is performed to Carrier 2 for 30 sec.
3
SS
SYSTEM INFORMATION 2QUATER
3a
SS
SYSTEM INFORMATION TYPE 13
See specific contents below.
4
SS
Verify that no cell reselection is performed to Carrier 2 for 65 sec.
5
SS
For FDD, reduce power of Carrier 1 to –77 dBm.
For TDD, increase power of Carrier 1 to –71 dBm.
6
MS -> SS
RRC CONNECTION REQUEST
Verify that the MS reselects to Carrier 2 within 30 sec.
Establishment cause shall be “interRAT-CellReselection”
Specific message contents
SYSTEM INFORMATION 2QUATER in Step 3
< MP_CHANGE_MARK : bit >
1
0 | 1 < 3G_MEASUREMENT Parameters Description >
0
< Qsearch_I : bit (4) >
For FDD:
‘0110’B (-74 dBm)
For TDD:
‘1100’B (above -74 dBm)
< Qsearch_C_Initial : bit (1) >
0
0 | 1 < FDD_Qoffset : bit (4) >
0
0 | 1 < TDD_Qoffset : bit (4) >
0
SYSTEM INFORMATION Type 13 in Step 3a
Information Element
Value/remark
< BCCH_CHANGE_MARK : bit (3) >
‘001’B
< SI_CHANGE_FIELD : bit (4) >
‘0010’B (Update of SI2, SI2 bis or SI2 ter message or any instance of SI2quater messages )
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.5 Intersystem Cell Reselection / Idle Mode / High Priority
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.5.1 Conformance requirement
|
If the 3G Cell Reselection list or the E-UTRAN Neighbour Cell list include frequencies of other radio access technologies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non serving GSM cells.
The MS shall then reselect a suitable (see 3GPP TS 25.304 for UTRAN and 3GPP TS 36.304 for E-UTRAN) cell of another radio access technology if the criteria below are satisfied. S_non-serving_XXX is the measurement quantity of a non-serving inter-RAT cell and XXX indicates the other radio access technology/mode and is defined as follows:
- for a UTRAN cell, is the measured RSCP value for the cell minus UTRAN_QRXLEVMIN for the cell’s frequency;
…
Cell reselection to a cell of another inter-RAT frequency shall be performed if any of the conditions below (to be evaluated in the order shown) is satisfied:
- The S_non-serving_XXX of one or more cells of a higher priority inter-RAT frequency is greater than THRESH_XXX_high during a time interval T_reselection; in that case, the mobile station shall consider the cells for reselection in decreasing order of priority and, for cells of the same priority, in decreasing order of S_non-serving_XXX, and reselect the first cell that satisfies the conditions above;
…
A UTRAN FDD cell shall only be reselected if, in addition to the criteria above, its measured Ec/No value is equal to or greater than FDD_Qmin - FDD_Qmin_Offset.
References:
3GPP TS 45.008, subclause 6.6.6
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.5.2 Test purpose
|
To verify that the MS uses the priority information and performs cell re-selection to High priority UTRAN cell while in Idle Mode.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.5.3 Method of test
|
Initial conditions
Parameter
Cell 1
Cell 2
Carrier1
Carrier2
Channel Type carried
BCCH
BCH
Signal Level (dBm)
-50
Off to -60
Ec/No (dB)
-
-6dB
NOTE 1: MS is GPRS attached on Cell 1.
NOTE 2: Carrier 1 is the BCCH carrier, NC0.
NOTE 3: Carrier 2 is the UTRAN FDD cell configured according to TS 34.108, clause 6.1.4, Default settings for cell No.1
NOTE 4: Serving Cell Parameters are coded and transmitted on the specified Channel Type
NOTE 5: Carriers should have a relative accuracy of ±3 dB.
NOTE 6: SYSTEM INFORMATION TYPE 2QUATER Instance1 and Instance2 as per 20.25.1.
Test procedure
The MS is GPRS attached and has received a 3G Neighbour Cell description in System Information Type 2quater message, along with priority information.
Update the Carrier 2, power level as per the initial conditions
It is verified that a Cell Reselection to UTRAN is performed within 30 sec.
Maximum duration of the test
5 minutes
Expected sequence
Step
Direction
Message
Comments
1
SS
Carrier 2 is activated with Ec/No = -6 (dB) and power level -60(dBm)
2
MS -> SS
RRC CONNECTION REQUEST
Verify that the MS reselects to Carrier 2 within 30 secs from Step 1.
Establishment cause shall be “interRAT-CellReselection”
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.6 Intersystem Cell Reselection / Idle Mode / Low Priority
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
20.25.6.1 Conformance requirement
|
If the 3G Cell Reselection list or the E-UTRAN Neighbour Cell list include frequencies of other radio access technologies, the MS shall, at least every 5 s update the value RLA_C for the serving cell and each of the at least 6 strongest non serving GSM cells.
The MS shall then reselect a suitable (see 3GPP TS 25.304 for UTRAN and 3GPP TS 36.304 for E-UTRAN) cell of another radio access technology if the criteria below are satisfied. S_non-serving_XXX is the measurement quantity of a non-serving inter-RAT cell and XXX indicates the other radio access technology/mode and is defined as follows:
- for a UTRAN cell, is the measured RSCP value for the cell minus UTRAN_QRXLEVMIN for the cell’s frequency;
…
For a GSM cell, S_GSM is defined as the C1 value for the cell (see subclause 6.4);
Cell reselection to a cell of another inter-RAT frequency shall be performed if any of the conditions below (to be evaluated in the order shown) is satisfied:
- The S_non-serving_XXX of one or more cells of a higher priority inter-RAT frequency is greater than THRESH_XXX_high during a time interval T_reselection; in that case, the mobile station shall consider the cells for reselection in decreasing order of priority and, for cells of the same priority, in decreasing order of S_non-serving_XXX, and reselect the first cell that satisfies the conditions above;
- The value of S_GSM is lower than THRESH_GSM_low for the serving cell and all measured GSM cells during a time interval T_reselection; in this case, the mobile station shall consider for reselection the inter-RAT cells in the following order, and reselect the first one that satisfies the following criteria:
- cells of a lower priority inter-RAT frequency whose S_non-serving_XXX is greater than THRESH_XXX_low during a time interval T_reselection; these cells shall be considered in decreasing order of priority and, for cells of the same priority, in decreasing order of S_non-serving_XXX;
…
A UTRAN FDD cell shall only be reselected if, in addition to the criteria above, its measured Ec/No value is equal to or greater than FDD_Qmin - FDD_Qmin_Offset.
References:
3GPP TS 45.008, subclause 6.6.6
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.