hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.1.4.1 Initial conditions
|
System simulator:
1 cell, default parameters.
Mobile Equipment:
Connected to a SIM-simulator with bit b2 of the file characteristics set to 1.
ME is powered on.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.1.4.2 Procedure
|
An authentication is made in the same way as in test [26.7.2. Authentication]. The MS is paged. After the MS has responded with a PAGING RESPONSE message to the SS, the SS initiates an authentication procedure, sending the MS the value RAND. During authentication, the SIM simulator checks the frequency of the clock supplied by the ME. Following the AUTHENTICATION RESPONSE from the MS, the SS sends CHANNEL RELEASE.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.1.5 Test requirement
|
The frequency of the clock shall be at least 13/4 MHz during the authentication procedure.
27.12.1a Operating speed in authentication procedure - for GPRS
27.12.1a.1 Definition
Authentication is performed by a GSM network on the SIM, by sending a random number to the SIM. The SIM then performs a calculation on the random number, and sends the result to the network for verification.
27.12.1a.2 Conformance requirement
If bit b2 of the file characteristics is set to 1, then the ME shall provide a clock frequency of at least 13/4 MHz to enable the SIM to run the authentication process in the required time.
3GPP TS 11.11 / 3GPP TS 51.011, subclause 5.4.
27.12.1a.3 Test purpose
To verify that the authentication procedure is done with a frequency of at least 13/4 MHz if the bit b2 of the file characteristics (byte 1 of the directory characteristics) is set to 1.
27.12.1a.4 Method of test
27.12.1a.4.1 Initial conditions
System simulator:
The SS transmits default message contents of Cell A, subclauses 40.1.1 and 40.2.1.1 on the BCCH, with the exception that Network Mode of Operation is set to NMO II.
Mobile Equipment:
Connected to a SIM-simulator with EF contents of GPRS SIM and additional with bit b2 of the file characteristics set to 1.
27.12.1a.4.2 Procedure
a) The MS is powered on.
b) After receipt of a CHANNEL REQUEST from the MS, the SS sends IMMEDIATE ASSIGNMENT to the MS.
c) After receipt of an ATTACH REQUEST from the MS, the SS sends AUTHENTICATION AND CIPHERING REQUEST to the MS, includes RAND set to any allowed value.
d) During authentication procedure, the SIM simulator checks the frequency of the clock supplied by the ME.
e) After receipt of an AUTHENTICATION AND CIPHERING RESPONSE from the MS, the SS sends ATTACH ACCEPT to the MS.
f) The MS is soft powered down.
27.12.1a.5 Test requirement
The frequency of the clock shall be at least 13/4 MHz during the authentication procedure.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2 Clock stop
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.1 Definition
|
The ME may switch off the clock signal to the SIM, but only if the SIM indicates that it supports this feature.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.2 Conformance requirement
|
1. The ME shall not stop the clock, unless the requirements indicated in byte 1 of the file characteristics are met.
3GPP TS 11.11, subclauses 5.6 and 9.2.1.
2. The ME shall wait at least 1 860 clock cycles after having received the last character including the minimum guard time (2 etu) of the response before switching off the clock. The ME shall wait at least 744 clock cycles before it sends the first command after having restarted the clock.
3GPP TS 11.11, subclause 5.6.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.3 Test purpose
|
1. To verify that the clock is only switched off if requirements are met as indicated in the file characteristics (byte 1 of the directory characteristics).
2. To verify that the timing of the clock switching is as specified.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.4 Method of test
|
Specific PICS statements:
• 5V only SIM/ME interface (TSPC_AddInfo_5V)
PIXIT statements:
-
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.4.1 Initial conditions
|
The ME is connected to a SIM simulator. CHV 1 is enabled.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.4.2 Procedure
|
a) A SIM simulator is used with bits set as follows:
Bit b1 Bit b3 Bit b4
0 0 0
b) The ME is powered on. When the ME is in mode PIN check, 10 s shall elapse before the PIN is entered.
c) The ME is powered off, and a SIM simulator is used with bits set as follows:
Bit b1 Bit b3 Bit b4
0 1 0
d) The ME is powered on. When the ME is in mode PIN check, 10 s shall elapse before the PIN is entered.
e) The ME is powered off, and a SIM simulator is used with bits set as follows:
Bit b1 Bit b3 Bit b4
0 0 1
f) The ME is powered on. When the ME is in mode PIN check, 10 s shall elapse before the PIN is entered.
g) The ME is powered off, and a SIM simulator is used with bits set as follows:
Bit b1 Bit b3 Bit b4
1 0 0
h) The ME is powered on. When the ME is in mode PIN check, 10 s shall elapse before the PIN is entered.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.12.2.5 Test requirement
|
1. During step b), the ME shall not switch off the clock. This applies only to MEs supporting 5V SIM interface (see PICS).
2. During step d), the ME shall not switch off the clock, unless at high level.
3. During step f), the ME shall not switch off the clock, unless at low level.
4. During steps d), f) and h), the ME shall not switch off the clock until at least 1 860 clock cycles after having received the last character of the response including the minimum guard time (2 etu).
5. During steps d), f) and h), the ME shall wait at least 744 clock cycles before it sends the first command after having restarted the clock.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13 Mechanical tests
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1 Contact pressure
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.1 Definition
|
The contacts of the card reader must exert a force to maintain a good electrical contact, but the force must not be excessive and damage the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.2 Conformance requirement
|
A contact force may not be greater than 0,5 N per contact.
3GPP TS 11.11, subclause 4.3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.3 Test purpose
|
To verify that the contact pressure of each contacting element is not greater than 0,5 N when each of the following types of card is used:
i) Unembossed.
ii) Embossed on the contact side.
iii) Embossed on the opposite side to the contacts.
NOTE: Only type i) applies to the plug-in SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.4.1 Initial conditions
|
The ME manufacturers shall provide a separate card reader (mechanical components) to make the measurement possible.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.4.2 Procedure
|
The pressure of each contacting element is measured.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.1.5 Test requirement
|
The contact pressure of each contacting element shall be not greater than 0,5 N.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2 Shape of contacts for IC card SIM card reader
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.1 Definition
|
The shape of the contacts is important to maintain a good electrical contact, but must not damage the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.2 Conformance requirement
|
The radius of curvature of the contacting elements shall be greater than or equal to 0,8 mm in the contact area of both axes.
3GPP TS 11.11, subclause 4.3.4.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.3 Test purpose
|
To verify that the radius of curvature of the contacting elements is greater than or equal to 0,8 mm in the contact area on both axes.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.4.1 Initial conditions
|
The ME manufacturers shall provide a separate card reader (mechanical components) to make the measurement possible.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.4.2 Procedure
|
The radius of curvature of the contacting elements is measured on both axes.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.13.2.5 Test requirement
|
The radius of curvature of the contacting elements shall be greater than or equal to 0,8 mm in the contact area on both axes.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14 Secret code usage
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1 Entry of PIN
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.1 Definition
|
The PIN is a number used to authenticate the user to the SIM for security. Entry of the correct PIN allows PIN-protected data to be accessed over the SIM-ME interface.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.2 Conformance requirement
|
Following insertion of the SIM and switching on the MS, the ME shall check the state of the PIN. If the PIN is enabled, the ME asks the user for PIN verification.
The VERIFY CHV function verifies the PIN presented by the ME to the SIM.
Reference:
3GPP TS 02.30, subclause 4.6.1; 3GPP TS 11.11, subclauses 8.9, 9.2.9 and 11.3.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.3 Test purpose
|
1. To verify that the PIN verification procedure is performed by the ME correctly.
2. To verify that the GSM basic public MMI string is supported.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.4.1 Initial conditions
|
The ME is connected to a SIM or SIM-simulator with the PIN enabled, and powered off.
The default SIM is used.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.4.2 Procedure
|
a) The ME is powered on.
b) When the MS is in mode "PIN check" enter "2468#".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.1.5 Test requirement
|
1) The ME shall send a VERIFY CHV command to the SIM, with CHV number = "01".
2) The MS shall give an indication "OK", following a successful execution of the command.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2 Change of PIN
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.1 Definition
|
The PIN may be changed by the user, by entering the old and new PINs. The length of the PIN is between 4 and 8 digits.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.2 Conformance requirement
|
The ME shall support the change of PIN procedure as defined in 3GPP TS 02.30 and 3GPP TS 11.11.
Reference:
3GPP TS 02.30, subclause 4.6.2; 3GPP TS 11.11, subclauses 8.10, 9.2.10 and 11.3.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.3 Test purpose
|
1. To verify that the PIN substitution procedure is performed correctly by the ME.
2. To verify that the GSM basic public MMI string is supported.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.4.1 Initial conditions
|
The ME is connected to a SIM or SIM-simulator with the PIN enabled.
The default SIM is used.
The ME is powered-on, with the correct PIN entered.
Specific PICS Statements:
- support of basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.4.2 Procedure
|
a) When the public basic MMI strings to change/unblock PIN are supported enter "**04*2468*01234567*01234567#", else initiate an equivalent MMI dependent procedure to change the PIN from '2468' to '01234567'.
b) The MS is switched off and on.
c) When the MS is in mode "PIN-check", the sequence "01234567#" is entered.
d) The MS is switched off and on.
e) When the MS is in mode "PIN check" enter "2468#".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.2.5 Test requirement
|
1) After step a), the ME shall send a CHANGE CHV command to the SIM, with CHV number set to "01".
2) Following the successful execution of the command, the MS shall give an indication that the new PIN is accepted.
3) After step c), the MS shall give an indication "OK".
4) After step e), the MS shall give an indication that the entered PIN is not accepted.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3 Disabling the PIN
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.1 Definition
|
Entry of the PIN may be disabled by the user, depending on the service table of the SIM. It is the responsibility of the ME to check the SIM service table.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.2 Conformance requirement
|
Disabling PIN is achieved through the DISABLE CHV command. If the PIN disable function in the SIM service table is not allocated or activated, then the ME shall not attempt to disable the PIN.
Reference:
3GPP TS 11.11, subclauses 8.11, 9.2.11, 10.2.7, 11 and 11.3.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.3 Test purpose
|
To verify that the ME does not attempt to disable the PIN.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.4.1 Initial conditions
|
The ME is connected to the SIM simulator.
Elementary files in the SIM simulator shall be default, with the exception of:
EFSST (SIM Service Table)
Logically: CHV1 disable function not activated.
Abbreviated dialling numbers allocated and activated.
PLMN selector allocated and activated.
Fixed dialling numbers not activated.
Coding:
B1
B2
B3
B4
Value (binary)
xx0x110x
0011xxxx
xxxxxxxx
0000xxxx
The coding of EFSST shall conform with the capabilities of the SIM simulator.
The ME is powered on and a correct PIN entered.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.4.2 Procedure
|
Using the ME's MMI procedure, an attempt is made to disable the PIN.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.3.5 Test requirement
|
The ME shall not send a DISABLE CHV command across the SIM/ME interface.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4 PUK entry
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.1 Definition
|
After three consecutive wrong entries of the PIN, the PIN becomes blocked. The PUK is used to unblock the PIN. This function may be performed whether or not the PIN is blocked.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.2 Conformance requirement
|
The ME shall support the procedure to unblock PIN using PUK, as defined in 3GPP TS 02.30 and 3GPP TS 11.11.
Reference:
3GPP TS 02.30, subclause 4.6.3; 3GPP TS 11.11, subclauses 8.13, 9.2.13 and 11.3.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.3 Test purpose
|
1. To verify that the CHV unblocking procedure is performed correctly.
2. To verify that the GSM basic public MMI string is supported.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.4.1 Initial conditions
|
The ME is connected to the SIM simulator.
The default SIM is used.
Specific PICS Statements:
- support of basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.4.2 Procedure
|
Step ‘a’ up to and including step ‘e’ are applicable if MS supports basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings).
a) The ME is powered on.
b) Enter "**05*13243546*1234*1234#"
c) The ME is powered off and on.
d) Enter the new PIN: "1234".
e) The ME is powered off.
f) The ME is powered on.
g) Enter a wrong PIN three times.
h) When the public basic MMI strings to change/unblock PIN are supported enter "**05*13243546*1357*1357#", else initiate an equivalent MMI dependent procedure to unblock the PIN with unblock code '13243546' and a new PIN '1357'.
i) The ME is powered off and on.
j) Enter the new PIN: "1357".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.4.5 Test requirements
|
Test requirement 1 and Test requirement 2 are not applicable for an ME that does not support basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)..
1. After step b), the ME shall send an UNBLOCK CHV command to the SIM, with CHV number = "00".
2. After step d), the ME shall indicate that the PIN has been accepted.
3. After step g), the ME shall indicate that the PIN has been blocked.
4. After step h), the ME shall send an UNBLOCK CHV command to the SIM, with CHV number = "00".
5. After step j), the ME shall indicate that the PIN has been accepted.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5 Entry of PIN2
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.1 Definition
|
PIN2 is a number used to authenticate the user to the SIM for security. Entry of the correct PIN2 allows PIN2-protected data to be accessed over the SIM-ME interface.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.2 Conformance requirement
|
Where entry of PIN2 is necessary for security access, the ME shall indicate that PIN2 is to be entered.
The VERIFY CHV function verifies the PIN presented by the ME to the SIM.
Reference:
3GPP TS 02.30, subclause 4.6.1; 3GPP TS 11.11, subclauses 8.9, 9.2.9 and 11.3.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.3 Test purpose
|
To verify that entry of PIN2 is processed by the ME correctly.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.4.1 Initial conditions
|
The ME is connected to a SIM or SIM-simulator and powered on, with the correct PIN entered.
A default FDN SIM is used.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.4.2 Procedure
|
a) A feature is accessed which requires the entry of PIN2, e.g. resetting ACM for Advice of Charge, or changing a Fixed Dialling Number.
b) The MMI is used to enter PIN2: "3579".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.5.5 Test requirement
|
1) After step b), the ME shall send a VERIFY CHV command to the SIM, with CHV number = "02".
2) Following the successful execution of the command, the MS shall give an indication that PIN2 was accepted.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6 Change of PIN2
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.1 Definition
|
The PIN2 may be changed by the user, by entering the old and new PIN2s. The length of the PIN is between 4 and 8 digits.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.2 Conformance requirement
|
The ME shall support the change of PIN2 procedure as defined in 3GPP TS 02.30 and 3GPP TS 11.11.
Reference:
3GPP TS 02.30, subclause 4.6.2; 3GPP TS 11.11, subclauses 8.10, 9.2.10 and 11.3.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.3 Test purpose
|
1. To verify that PIN2 substitution procedure is performed correctly by the ME.
2. To verify that the GSM basic public MMI string is supported.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.4.1 Initial conditions
|
The ME is connected to a SIM or SIM-simulator.
The default FDN SIM is used, with PIN enabled.
The ME is powered on, with the correct PIN entered.
Specific PICS Statements:
- support of basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.4.2 Procedure
|
a) When the public basic MMI strings to change/unblock PIN are supported enter "**042*3579*12345678*12345678#", else initiate an equivalent MMI dependent procedure to change the PIN2 from '3579' to '12345678'.
b) The MS is switched off and on, and PIN entered: "2468".
c) When the public basic MMI strings to change/unblock PIN are supported enter "**042*3579*12345678*12345678#", else initiate an equivalent MMI dependent procedure to change the PIN2 from '3579' to '12345678'.
d) When the public basic MMI strings to change/unblock PIN are supported enter "**042*12345678*3579*3579#", else initiate an equivalent MMI dependent procedure to change the PIN2 from '12345678' to '3579'.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.6.5 Test requirement
|
1) After step a), the ME shall send a CHANGE CHV command to the SIM, with CHV number set to "02".
2) Following the successful execution of the command, the MS shall give an indication that the new PIN2 is accepted.
3) After step c), the MS shall give an indication that the new PIN2 is not accepted.
4) After step d), the MS shall give an indication that the new PIN2 is accepted.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7 PUK2 entry
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.1 Definition
|
After three consecutive wrong entries of PIN2, it becomes blocked. PUK2 is used to unblock PIN2. This function may be performed whether or not PIN2 is blocked.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.2 Conformance requirement
|
The ME shall support the procedure to unblock PIN2 using PUK2, as defined in 3GPP TS 02.30 and 3GPP TS 11.11.
Reference:
3GPP TS 02.30, subclause 4.6.3; 3GPP TS 11.11, subclauses 8.13, 9.2.13 and 11.3.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.3 Test purpose
|
1. To verify that the PUK2 unblock procedure is performed correctly by the ME.
2. To verify that the GSM basic public MMI string is supported.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.4.1 Initial conditions
|
The ME is connected to the SIM simulator.
The default FDN SIM is used, with PIN enabled.
Specific PICS Statements:
- support of basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.4.2 Procedure
|
Step ‘a’ up to and including step ‘c’ are applicable if MS supports basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings).
a) The ME is powered on and a correct PIN entered.
b) Enter "**052*08978675*1234*1234#".
c) The MS is powered off.
d) The MS is powered on, and a correct PIN entered.
e) A feature is selected requiring the entry of PIN2.
f) A wrong PIN2 is entered three times.
g) When the public basic MMI strings to change/unblock PIN are supported enter "**052*08978675*3579*3579#", else initiate an equivalent MMI dependent procedure to unblock the PIN2 with unblock code '08978675' and a new PIN2 '3579'.
h) A feature is selected requiring the entry of PIN2, and the new PIN2 "3579" is entered.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.14.7.5 Test requirements
|
Test requirement 1 is not applicable for an ME that does not support basic public MMI strings to change/unblock PIN (TSPC_PIN_MMI_Strings)..
1. After step b), the ME shall send an UNBLOCK CHV command to the SIM, with CHV number = "02".
2. After step f), the ME shall indicate that PIN2 has been blocked.
3. After step g), the ME shall send an UNBLOCK CHV command to the SIM, with CHV number = "02".
4. After step h), the ME shall indicate that PIN2 has been accepted.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15 Abbreviated Dialling Numbers (ADN)
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.1 Definition
|
Abbreviated Dialling Numbers contain subscriber number and supplementary service control strings. They may also contain alpha identifiers.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.2 Conformance requirement
|
The ME shall be able to manage the storage and retrieval of ADNs from the SIM, and set up calls to these numbers.
Reference:
3GPP TS 02.07, subclause B.3.1; 3GPP TS 02.30 subclause 4.6.4; 3GPP TS 11.11, subclause 11.5.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.3 Test purpose
|
To verify that the ME manages the storage and retrieval of ADNs from the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.4 Method of Test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.4.1 Initial conditions
|
Coding of elementary files in the SIM shall be as default, with the addition of:
EFADN (Abbreviated Dialling Number)
Logically:
At least 101 records, each record unique. Example of record 1 below
Record 1: Length of alpha identifier: 32 characters
Alpha identifier: "ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEF"
Length of BCD number: "03"
TON and NPI: Telephony and Unknown
Dialled number: 123
CCI: None
Ext1: None
Coding:
For record 1:
B1
B2
B3
...
B32
B33
B34
B35
B36
B37
B38
B39
...
B46
41
42
43
...
46
03
81
21
F3
FF
FF
FF
...
FF
The ME is installed with the default SIM or SIM simulator, and switched on.
The code "+123456789012345" is stored as abbreviated dialling entry number 7 on the SIM.
The code "00112233" is stored as abbreviated dialling entry number 6 on the SIM.
The code "**21*44556677#" is stored as abbreviated dialling entry number 101 on the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.4.2 Procedure
|
a) Retrieve data from SIM entry number 7 using the procedure N(N)(N)#.
b) Retrieve data from SIM entry number 6 using the procedure N(N)(N)#.
c) Retrieve data from SIM entry number 101 using the procedure N(N)(N)#.
d) Retrieve data from SIM entry number 1 using the procedure N(N)(N)#.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.15.5 Test requirements
|
1) After step a), the number "+123456789012345" shall be displayed.
2) After step b), the number "00112233" shall be displayed.
3) After step c), the number "**21*44556677#" (or an equivalent representation) shall be displayed.
4) After step d), the number “123” shall be displayed.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16 MMI reaction to SIM status encoding
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.1 Definition
|
The SIM gives status information in response to instructions, as two-byte codes. Some of these codes give valuable information to the user, and appropriate indication by the ME is mandatory.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.2 Conformance requirement
|
It is mandatory to give the user an appropriate indication when any of the codes given below appear.
Reference:
3GPP TS 02.30, subclause 4.6.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.3 Test purpose
|
To verify that the ME gives an appropriate indication to the user in response to status information return codes from the SIM.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.4.1 Initial conditions
|
The ME is connected to the SIM simulator. All elementary files are coded as default.
The ME is powered on.
27.16.4.2 Procedure.
The SIM simulator is used to send the following error codes as reaction on an instruction from the ME:
- 9240 Memory Problem;
- 9804 Access security policy not fulfilled or secret code rejected;
- 9840 Secret code locked;
- 6FXX Technical problem with no diagnostic given as reaction on an instruction from the ME.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
27.16.5 Test requirement
|
For each error code, the ME shall give an appropriate MMI indication.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.