hash
stringlengths 32
32
| doc_id
stringlengths 5
12
| section
stringlengths 4
1.47k
| content
stringlengths 0
6.67M
|
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.1 Definition
|
-
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.2 Conformance requirement
|
An MS claiming to not support the MultiParty supplementary service and in the U10 call active state with one call and in the held state with another call shall, when the appropriate MultiParty MMI command is entered:
- Fail to combine the three parties in a MultiParty call.
- Optionally provide some indication to the user of an error.
3GPP TS 02.83, 3GPP TS 02.84, 3GPP TS 04.83, 3GPP TS 04.84.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.3 Test purpose
|
To verify that an MS claiming to not support the MultiParty supplementary service and in the U10 call active state with one call and another call on hold, reacts in the following manner when the appropriate MultiParty MMI command is entered:
- Fails to combine the three parties in a MultiParty call.
- Optionally provides some indication to the user of an error.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.4.1 Initial conditions
|
The mobile originating generic call set up procedures shall be followed up to and including the transmission by the MS of the CONNECT ACKNOWLEDGE to place the call in the U10 call active state. A second directory number is then entered followed by send to put the first call on hold and place a second call.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.4.2 Procedure
|
"3" followed by "SEND" is entered via the MMI.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.5.5 Test requirement
|
The MS shall not send a FACILITY message, containing the build multiparty request, on the dedicated channel. This is checked for 3 s.
The MS may however send other messages.
The MS may also give the user an indication of the error that has occurred.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6 Verification of non-support of feature (Fixed Dialling Number (FDN))
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.1 Definition
|
-
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.2 Conformance requirement
|
1. An MS claiming to not support FDN that has a SIM with FDN allocated and activated in its SIM Service Table (Service Number 3) and has FDN "enabled" shall refuse a request from the user to attempt an outgoing call.
2. An MS claiming to not support FDN that has a SIM with FDN allocated and activated in its SIM Service Table (Service Number 3) and has FDN "enabled" shall not respond to paging.
3. An MS claiming not to support FDN that has a SIM with FDN allocated and activated shall not attempt to rehabilitate the IMSI and Location Information Elementary Files of the SIM.
3GPP TS 02.07 subclause B3.2, 3GPP TS 11.11 subclause 11.2.1.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.3 Test purpose
|
1. To verify that an MS claiming to not support FDN and that has a SIM with FDN allocated and activated in its SIM Service Table and has FDN "enabled". i.e. AND, IMSI and Location Information Elementary Files are Invalidated inserted, it refuses an attempt to make an outgoing call made by the user.
2. To verify that an MS claiming to not support FDN and that has a SIM with FDN allocated and activated in its SIM Service Table and has FDN "enabled". i.e. AND, IMSI and Location Information Elementary Files are Invalidated inserted, it does not answer to paging.
3. To verify that an MS claiming not to support FDN and that has a SIM with FDN allocated and activated in its SIM Service Table and has FDN "enabled". i.e. AND, IMSI and Location Information Elementary Files are Invalidated inserted, does not attempt to rehabilitate IMSI and Location Information.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.4 Method of test
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.4.1 Initial conditions
|
The ME is powered off. No SIM is inserted in the ME.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.4.2 Procedure
|
a) A SIM with FDN allocated and activated in its SIM Service Table and has FDN "enabled" is inserted in the ME and the MS is powered on.
b) An outgoing CM connection is attempted by the user.
c) The MS paged with its IMSI.
d) The MS is powered off and the SIM is examined using a suitable tool to determine if the IMSI and Location Information Elementary Files have been Rehabilitated.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.6.5 Test requirement
|
1) in step b), the MS shall not send a CHANNEL REQUEST message.
2) in step c), the MS shall not send a CHANNEL REQUEST message.
3) in step d), the IMSI an Location Information Elementary Files shall be Invalidated.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.7 IMEI Security
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.7.1 Conformance requirements
|
The IMEI shall not be changed after the ME's final production process. It shall resist tampering, i.e. manipulation and change, by any means (e.g. physical, electrical and software).
NOTE: This requirement is valid for new GSM Phase 2 and Release 96, 97, 98 and 99 MEs type approved after 1st June 2002.
3GPP TS 02.09, 3GPP TS 02.16, 3GPP TS 03.03.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.7.2 Test purpose
|
To verify the conformance requirement.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.7.3 Method of test
|
Not available.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.7.4 Declaration
|
The manufacturer shall declare that:
- he has taken necessary and sufficient steps to ensure that any individual or organisation cannot economically change the IMEI after the ME's final production process; and
- that the IMEI resists tampering, i.e. manipulation and change, by any means (e.g. physical, electrical and software).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8 Coding of the Bearer Capability information element
|
This subclause describes the coding of the bearer capability IE in a SETUP and in a CALL CONFIRMED message according to 3GPP TS 07.01 and 3GPP TS 04.08 / 3GPP TS 24.008.
More precisely, the matter of subclause 11.8.1 is the coding of the bearer capability IE in a mobile terminating SETUP and subclause 11.8.2 deals with the coding of the bearer capability IE in a mobile originating SETUP and in a CALL CONFIRMED message.
In the whole section "x", "y" and "X" have the following meanings:
- when a field is coded with values of "x", it means that several bit combinations are authorized and the allowable ones are described in the relevant paragraph or section;
- "y" means that the value of the spare bit can be set to either 0 or 1 at the sending side and that the receiving side shall accept either of these values;
- "X" in the hexadecimal coding of the Bearer Capability IE reflects all the possible values taken by an octet taking account of the number of bits coded as '"x" or "y" and their place in the octet.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1 Network to MS Direction
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1 BS 21 to 26 - Asynchronous Service
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.1 BS 21
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.1.1 3,1 kHz Audio, Transparent
|
BC GSM = 04 07 AX X8 81 21 X1 4X 81
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement: Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
1
Modem Type: V.21
The following configuration is also authorized:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.1.2 3,1 kHz Audio, Non Transparent
|
BC GSM = 04 0X X2 XX 81 21 X1 6X A1 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
y
y
Radio Channel Requirement: Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
1
Connection Element: Non transparent
0
0
0
0
1
Modem Type: V.21
Octet 7
1
Extension
(note)
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending on the TE Configuration
NOTE: Because Modem Type is V.21, Octet7 shall be present.
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
The following configuration is also authorized:
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.1.3 UDI, Transparent
|
BC GSM = 04 07 X1 X8 89 21 X1 4X 80
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement: Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
0
Modem Type: None
The following configuration is also authorized:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.1.4 UDI, Non Transparent
|
BC GSM = 04 0X X1 XX 89 21 X1 6X A0 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
1
Connection Element: Non Transparent
0
0
0
0
0
Modem Type: None
Octet 7 (need not be present)
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending of the TE Configuration
Depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control". If octet 7 is present, the value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
The following configuration is also authorized:
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.2 BS 22
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.3 BS 24
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.4 BS 25
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.5 BS 26
|
Same as BS 21 except:
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.1.6 BS 23
|
For MOC only.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2 BS 31 to 34 - Synchronous Service
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1 BS 32
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1.1 3,1 kHz Audio, Transparent, non-X.32 case
|
BC GSM = 04 07 X2 X8 81 20 13 43 83
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
1
1
Modem Type: V.22 bis
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1.2 UDI, Transparent mode, non-X.32 case
|
BC GSM = 04 07 X1 X8 8X 20 13 43 80
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
0
x
x
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
0
Modem Type: none
If the mobile station supports only SAP I.440/450, the System Simulator sets SAP field value to::
SAP in Octet 5:
-
-
-
-
-
0
0
1
I.440/I.450
If the MS supports only SAP X.21, SAP field is set to:
SAP in Octet 5:
-
-
-
-
-
0
1
0
X.21
Else, the MS supports both values and SAP is set to:
either:
SAP in Octet 5:
-
-
-
-
-
0
0
1
I.440/I.450
or:
SAP in Octet 5:
-
-
-
-
-
0
1
0
X.21
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1.3 3,1 kHz Audio, Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 07 X2 X8 86 20 13 43 83
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
1
1
Modem Type: V.22 bis
The following configuration is also authorized:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
UIL2P in Octet 7
-
-
-
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1.4 3,1 kHz Audio, Non Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 07 X2 XX 86 20 13 63 A3 C6
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
1
Connection Element: Non Transparent
0
0
0
1
1
Modem Type: V.22 bis
Octet 7
1
Extension
1
0
Layer 2 Id.
0
0
1
1
0
X.25
The following configuration is also authorized:
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.1.5 UDI, Non Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 08 X1 XX 96 20 13 63 A0 C6
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
1
0
Rate Adaptation: X.31 flagstuffing
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
1
Connection Element: Non Transparent
0
0
0
0
0
Modem Type: None
Octet 7
1
Extension
1
0
Layer 2 Id.
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.2 BS 31
|
For non X.32 case only, same as BS 32 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
BS31 for Packet Service does not exist.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.3 BS 33
|
Same as BS 32 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.2.4 BS 34
|
Same as BS 32 except:
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.3 BS 61 - Alternate Speech / Data
|
The first BC in the Setup message is coded "Speech": 04 01 A0.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.3.1 Speech/Asynchronous Data, Transparent
|
BC GSM = 04 07 X2 X8 81 21 XX XX 8X
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
x
x
x
x
Modem Type
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
0
1
0,3 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
0
1
Modem V.21
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
The following configuration is also authorized:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
User Information L2 Protocol (see Non Transparent service).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.3.2 Speech/Asynchronous Data, Non Transparent
|
BC GSM = 04 0X X2 XX 81 21 XX 6X AX (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
x
x
x
x
User Rate
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
0
1
Connection Element: Non transparent
0
x
x
x
x
Modem Type
Octet 7 (may not be present)
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending of the TE Configuration
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control". The "Outband Flow control is not allowed with V.21 modem).
Depending of the user rate supported by the MS, the user rate and the modem type change:
User Rate in Octet 6a:
-
-
-
-
0
0
0
1
0,3 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
0
1
Modem V.21
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
The following configuration is also authorized:
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.3.3 Speech/Synchronous Data
|
BC GSM = 04 07 X2 X8 81 20 1X X3 8X
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
x
x
x
x
Modem Type
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.4 BS 81 - Speech followed by Data
|
The first BC in the Setup message is coded "Speech": 04 01 A0.
The repeat Indicator in the Setup message is coded “Circular for successive selection "mode 1 alternate mode 2": D1”.
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.4.1 Speech followed by Asynchronous Data
|
See subclauses 11.8.1.3.1 and 11.8.1.3.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.4.2 Speech followed by Synchronous Data
|
See subclause 11.8.1.3.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.5 TS 61 - Alternate Speech / Facsimile group 3
|
The first BC in the Setup message is coded "Speech": 04 01 A0.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.5.1 TS 61 - Alternate Speech / Facsimile group 3, Transparent
|
BC GSM = 04 07 X3 X8 81 20 1X X3 80
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
1
Info. Transfer Cap.: FAX3
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: NA
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
0
Modem Type: None
Depending of the user rate supported by the MS, the user rate and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.5.2 TS 61 - Alternate Speech / Facsimile group 3, Non-Transparent
|
BC GSM = 04 07 X3 XX 81 20 1X 63 X0
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
1
Info. Transfer Cap.: FAX3
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: NA
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
1
Intermediate Rate: 16 kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
x
x
Connection Element
0
0
0
0
0
Modem Type: None
Depending of the user rate supported by the MS, the MS may have the following values:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Depending on the support or not of both modes, Non Transparent and Transparent, the connection element field may have the following values:
Connection element in Octet 6c:
-
0
1
-
-
-
-
-
Non transparent
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
If present, Octet 7 shall have the following value:
Octet 7
1
Extension
1
0
Layer 2 id
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.1.6 TS 62 - Automatic Facsimile group 3
|
The repeat Indicator in the Setup message is not available.
The BC GSM is coded as described in subclause 11.8.1.5.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2 MS to SS direction
|
In the whole subclause 11.8.2, "1)" and "2)" stand for:
1) Not applicable in a CALL CONFIRMED message.
2) Not applicable in a CALL CONFIRMED message responding to a SETUP message with no BC-IE (PSTN-originated call with single numbering scheme).
If the MS supports only Full Rate:
Radio Channel Requirement in Octet 3:
-
0
1
-
-
-
-
-
Full rate support only mobile station
Else
Radio Channel Requirement in Octet 3:
-
1
x
-
-
-
-
-
Dual rate mobile station
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1 BS 21 to 26 - Asynchronous Service
|
If the MS supports only SAP I.440/I.450:
SAP in Octet 5:
-
-
-
-
-
0
0
1
I.440/I.450
If the MS supports only SAP X.28 non dedicated PAD:
SAP in Octet 5:
-
-
-
-
-
1
0
1
X.28 nond
Else:
SAP in Octet 5:
-
-
-
-
-
x
0
1
I.440/I.450 or X.28 nond
The use of the alternative configuration "Autobauding modem type 1" in BS 22 to BS 26 is the same as indicated for BS 21 in subclauses 11.8.2.1.1.1 and 11.8.2.1.1.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.1 BS 21
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.1.1 3,1 kHz Audio, Transparent
|
BC GSM = 04 0X X2 X8 8X 21 X1 XX X1 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on the presence of octet 7.
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
x
x
Structure
1
Duplex Mode
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
x
0
1
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
x
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element
0
0
0
0
1
Modem Type: V.21
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4:
-
1
1
-
-
-
-
-
Unstructured
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Connection element in Octet 6c:
-
0
0
-
-
-
-
-
Transparent
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
User Information L2 protocol in Octet 7 (see Non Transparent service)
2) The following configuration is also authorised in the SETUP message:
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
Modem type in Octet 6c (if CE = "both":
-
-
-
0
1
0
0
0
Autobauding Type 1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.1.2 3,1 kHz Audio, Non Transparent
|
BC GSM = 04 0X X2 XX 8X 21 X1 6X X1 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
x
0
1
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element: NT, (Both T or Both NT)1)
0
0
0
0
1
Modem Type: V.21
Octet 7 (need not be present)
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending on the TE Configuration
The following configuration is also authorised:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.1.3 2) UDI, Transparent
|
BC GSM = 04 0X X1 X8 8X 21 X1 XX X0
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on the presence of octet 7
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
x
x
Structure
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
x
0
1
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element
0
0
0
0
0
Modem Type: None
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4:
-
1
1
-
-
-
-
-
Unstructured
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Connection element in Octet 6c:
-
0
0
-
-
-
-
-
Transparent
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
User Information L2 protocol in Octet 7 (see Non Transparent service).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.1.4 2) UDI, Non Transparent
|
BC GSM = 04 0X X1 XX 8X 21 X1 6X X0 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
x
0
1
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element: NT, (Both T or Both NT) 1)
0
0
0
0
0
Modem Type: None
Octet 7 (need not be present)
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending of the TE Configuration
Depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control". If octet 7 is present, the value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.2 BS 22
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.3 BS 24
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
1
0
1
Modem V.26ter
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.4 BS 25
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.5 BS 26
|
Same as BS 21 except:
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.1.6 BS 23
|
Same as BS 21 except:
User Rate in Octet 6a:
-
-
-
-
0
1
1
1
1,2 kbit/s/75 bit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
0
0
Modem V.23
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2 BS 31 to 34 - Synchronous Service
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1 BS 32
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1.1 3,1 kHz Audio, Transparent, non-X.32 case
|
BC GSM = 04 07 X2 X8 81 20 13 43 83
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement : Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
x
x
1
Modem Type: V.22 bis or V.26 ter
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1.2 2) UDI, Transparent mode, non-X.32 case
|
BC GSM = 04 07 X1 X8 8X 20 13 43 80
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
0
x
x
Signalling Access Protocol
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
0
Intermediate Rate: 8kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
0
Modem Type: none
If the mobile station supports only SAP I.440/450
SAP in Octet 5:
-
-
-
-
-
0
0
1
I.440/I.450
If the MS supports only SAP X.21
SAP in Octet 5:
-
-
-
-
-
0
1
0
X.21
Else
SAP in Octet 5:
-
-
-
-
-
0
x
x
I.440/I.450 or X.21
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1.3 3,1 kHz Audio, Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 0X X2 X8 86 20 13 X3 X3 (C6)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
x
x
Structure
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
x
x
Connection Element: Transparent
0
0
x
x
1
Modem Type: V.22 bis or V.26 ter
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4:
-
1
1
-
-
-
-
-
Unstructured
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Connection element in Octet 6c:
-
0
0
-
-
-
-
-
Transparent
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
UIL2P in Octet 7
-
-
-
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1.4 3,1 kHz Audio, Non Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 08 A2 XX 86 20 13 63 X3 C6
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
x
x
Connection Element: NT, (Both T or Both NT)1)
0
0
x
x
1
Modem Type: V.22 bis or V.26 ter
Octet 7
1
Extension
1
0
Layer 2 Id.
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.1.5 2) UDI, Non Transparent mode, X.32 case (Packet Service)
|
BC GSM = 04 08 X1 XX 96 20 13 63 A0 C6
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
1
0
Rate Adaptation: X.31 flagstuffing
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
1
Connection Element: Non Transparent
0
0
0
0
0
Modem Type: None
Octet 7
1
Extension
1
0
Layer 2 Id.
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.2 BS 31
|
For non X.32 case only, same as BS 32 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
BS31 for Packet Service does not exist.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.3 BS 33
|
Same as BS 32 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.2.4 BS 34
|
Same as BS 32 except:
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
If different from "none",
Modem Type Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3 BS 41 to 46 - PAD Access Asynchronous
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.1 2) BS 41
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.1.1 2) UDI, Transparent
|
BC GSM = 04 0X X1 X8 8C 21 X1 XX X0 (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
x
x
Structure
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
1
0
0
Signalling Access Protocol: X.28 dedicated universal NUI
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element
0
0
0
0
0
Modem Type: None
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4:
-
1
1
-
-
-
-
-
Unstructured
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Connection element in Octet 6c:
-
0
0
-
-
-
-
-
Transparent
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
User Information L2 Protocol (see Non Transparent service).
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.1.2 2) UDI, Non transparent
|
BC GSM = 04 08 X1 XX 8C 21 X1 6X X0 CX
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length.
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
1
Rate Adaptation: V.110
1
0
0
Signalling Access Protocol: X.28 dedicated PAD, universal NUI
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
0
0
0
1
User Rate: 0,3 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element: NT, (Both T or Both NT)1)
0
0
0
0
0
Modem Type: None
Octet 7
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol: Depending on the TE Configuration
Depending on the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control". If octet 7 is present, the value COPnoFLCT (01100) means "No flow control".
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.2 BS 42
|
Same as BS 41 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.3 BS 44
|
Same as BS 41 except:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.4 BS 45
|
Same as BS 41 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.5 BS 46
|
Same as BS 41 except:
NIRR in Octet 4
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.3.6 BS 43
|
Same as BS 41 except:
User Rate in Octet 6a:
-
-
-
-
0
1
1
1
1,2 kbit/s 75bit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.4 BS 51 to 53 - Packet Service Synchronous
| |
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.4.1 2) BS 51
|
BC GSM = 04 08 X1 X8 96 20 13 63 A0 C6
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
1
0
0
0
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
0
1
Info. Transfer Cap.: UDI
Octet 4
1
Extension
y
Spare
0
0
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
1
0
Rate Adaptation: X.31 flag.
1
1
0
Signalling Access Protocol: X.32
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
0
0
1
1
User Rate: 2,4 kbit/s
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
1
Connection Element: Non Transparent
0
0
0
0
0
Modem Type: None
Octet 7
1
Extension
1
0
Layer 2 Id.
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.4.2 BS 52
|
Same as BS 51 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.4.3 BS 53
|
Same as BS 51 except:
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.5 BS 61 - Alternate Speech / Data
|
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2;
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.5.1 Speech/Asynchronous Data, Transparent
|
BC GSM = 04 0X X2 X8 81 21 XX XX XX (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
x
x
Structure
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element
0
x
x
x
x
Modem Type
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4:
-
1
1
-
-
-
-
-
Unstructured
Intermediate rate in Octet 6b:
-
1
x
-
-
-
-
-
Depending on the user rate
Connection element in Octet 6c:
-
0
0
-
-
-
-
-
Transparent
1) If the mobile station supports both Transparent and Non Transparent modes
Structure in Octet 4:
-
0
0
-
-
-
-
-
SDU Integrity
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Connection element in Octet 6c:
-
1
x
-
-
-
-
-
Both T or NT preferred
User Information L2 protocol in Octet 7 (see Non Transparent service)
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
0
1
0,3 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
0
0
1
Modem V.21
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
1
0
1
Modem V.26ter
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
1
1
1
1,2 kbits/s 75bit/2
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s in Transparent mode
Modem type in Octet 6c:
-
-
-
0
0
1
0
0
Modem V.23
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c:
-
-
-
0
1
0
0
0
Autobauding Type 1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.5.2 Speech/Asynchronous Data, Non Transparent
|
BC GSM = 04 0X X2 XX 81 21 XX 6X XX (CX)
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
x
x
x
x
Length (7 or 8) depending on presence of octet 7.
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
1
Synchronous / Asynchronous: Asynchronous
Octet 6a
0
Extension
x
Number of Stop Bits, Depending of the TE Configuration
0
Negotiation: In band Negotiation not possible
x
Number of Data Bits, Depending of the TE Configuration
x
x
x
x
User Rate
Octet 6b
0
Extension
1
1
Intermediate Rate: 16kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
x
x
x
Parity, Depending of the TE Configuration
Octet 6c
1
Extension
x
x
Connection Element: NT, (Both T or Both NT)1)
0
x
x
x
x
Modem Type
Octet 7 (may not be present)
1
Extension
1
0
Layer 2 Id.
0
1
x
0
0
User Inform. layer 2 protocol, Depending of the TE Configuration
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control". The "Outband Flow control is not allowed with V.21 modem).
Depending of the user rate supported by the MS, the user rate and the modem type change:
User Rate in Octet 6a:
-
-
-
-
0
0
0
1
0,3 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
0
1
Modem V.21
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
1
0
1
Modem V.26ter
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
-
-
-
0
1
0
0
0
Autobauding Type 1
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
-
-
-
0
1
0
0
0
Autobauding Type 1
User Rate in Octet 6a:
-
-
-
-
0
1
1
1
1,2 kbit/s 75bit/s
Modem type in Octet 6c:
-
-
-
0
0
1
0
0
Modem V.23
-
-
-
0
1
0
0
0
Autobauding Type 1
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.5.3 Speech/Synchronous Data
|
BC GSM = 04 07 X2 X8 81 20 1X X3 8X
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
x
x
Radio Channel Requirement
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
0
Info. Transfer Cap.: 3,1 kHz Audio
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: I.440 / I.450
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: Synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
x
x
x
x
Modem Type
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
1
0
1,2 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
0
Modem V.22
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
0
1
1
Modem V.22bis
1
0
1
Modem V.26ter
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Intermediate rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Intermediate rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
Modem type in Octet 6c:
-
-
-
0
0
1
1
0
Modem V.32
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.6 BS 81 - Speech followed by Data
|
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2.
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection 'mode 1 alternate mode 2' : D1".
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.6.1 Speech followed by Asynchronous Data
|
See subclauses 11.8.2.5.1 and 11.8.2.5.2.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.6.2 Speech followed by Synchronous Data
|
See subclause 11.8.2.5.3.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.7 TS 61 - Alternate Speech / Facsimile group 3
|
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2.
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.7.1 TS 61 - Alternate Speech / Facsimile group 3, Transparent
|
BC GSM = 04 07 X3 X8 81 20 1X X3 80
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement: Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
1
Info. Transfer Cap.: FAX3
Octet 4
1
Extension
y
Spare
1
1
Structure: Unstructured
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
0
Negotiation of Intermediate Rate Requested: No meaning
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: NA
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
x
Intermediate Rate
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
0
0
Connection Element: Transparent
0
0
0
0
0
Modem Type: None
Depending of the user rate supported by the MS, the user rate and the intermediate rate change:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
Interm. Rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
Interm. Rate in Octet 6b:
-
1
0
-
-
-
-
-
8 kbit/s
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
Interm. Rate in Octet 6b:
-
1
1
-
-
-
-
-
16 kbit/s
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.7.2 TS 61 - Alternate Speech / Facsimile group 3, Non Transparent
|
BC GSM = 04 07 X3 XX 81 20 1X 63 X0 66
Octet 1
0
0
0
0
0
1
0
0
Information Element: Bearer Capability
Octet 2
0
0
0
0
0
1
1
1
Length
Octet 3
1
Extension
y
y
Radio Channel Requirement: Spare
0
Coding Standard: GSM
0
Transfer Mode: Circuit
0
1
1
Info. Transfer Cap.: FAX3
Octet 4
1
Extension
y
Spare
0
0
Structure: SDU Integrity
1
Duplex Mode: Full duplex
0
Configuration: Point to Point
x
Negotiation of Intermediate Rate Requested
0
Establishment: Demand
Octet 5
1
Extension
0
0
Access Id
0
0
Rate Adaptation: No
0
0
1
Signalling Access Protocol: NA
Octet 6
0
Extension
0
1
Layer 1 Id: Default
0
0
0
0
User Information Layer 1 Protocol
0
Synchronous / Asynchronous: synchronous
Octet 6a
0
Extension
0
Number of Stop Bits: NA
0
Negotiation: In band Negotiation not possible
1
Number of Data Bits: NA
x
x
x
x
User Rate
Octet 6b
0
Extension
1
1
Intermediate Rate: 16 kbit/s
0
NIC on TX: Not Required
0
NIC on RX: Not Supported
0
1
1
Parity: NA
Octet 6c
1
Extension
x
x
Connection Element
0
0
0
0
0
Modem Type: None
Octet 7
1
Extension
1
0
Layer 2 Id
0
0
1
1
0
X.25
The user rate supported by the MS may have the following values:
User Rate in Octet 6a:
-
-
-
-
0
0
1
1
2,4 kbit/s
User Rate in Octet 6a:
-
-
-
-
0
1
0
0
4,8 kbit/s
NIRR in Octet 4:
-
-
-
-
-
-
0
-
no meaning
User Rate in Octet 6a:
-
-
-
-
0
1
0
1
9,6 kbit/s
If present, Octet 7 shall have the following value:
UI2LP in Octet 7
-
-
-
0
0
1
1
0
X.25
|
683b5b8a98f7b1390ddd5516ea9247a2
|
51.010-1
|
11.8.2.8 TS 62 - Automatic Facsimile group 3
|
The repeat Indicator in the Setup message is not available.
The BC GSM is coded as described in subclause 11.8.2.7.
|
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.